Wyszukiwarka
Katedra Elektrochemii, Korozji i Inżynierii Materiałowej
Publikacje
Filtry
wszystkich: 510
Katalog Publikacji
Rok 2021
-
Investigation of the 0.4C-35Cr-45Ni-Nb Alloy after Service in High-Temperature Steam and Hydrocarbons Environment
PublikacjaThe paper presents the results of investigation of the 0.4C-35Cr-45Ni-Nb alloy, which operated in the cracked hydrocarbon feeds and dilution steam at 1125 C. The material originated from the pyrolytic furnace coil tubes, of which internal walls were in contact with the aforementioned medium, whereas the external walls were in contact with the flue gases. The examination included metallographic and mechanical tests on the material...
-
Laser-assisted approach for improved performance of Au-Ti based glucose sensing electrodes
PublikacjaThis paper focuses on the synthesis route and electrochemical properties of electrocatalytic material based on gold nanoparticles (NPs) embedded in a structured titanium template obtained via optimized anodization, chemical etching and laser processing. SEM inspection reveals the presence of Au NPs (60–90 nm in diameter) sited in the titanium foil cavities. Performed electrochemical measurements enable nomination of the set of working...
-
Low-power microwave-induced fabrication of functionalised few-layer black phosphorus electrodes: A novel route towards Haemophilus Influenzae pathogen biosensing devices
PublikacjaIn this paper, various passivation schemes were applied at few-layer black phosphorus (FLBP) to achieve covalent functionalisation with 4-azidobenzoic acid, improving its electrochemical response intended for analytical and biosensing applications. The thermal and microwave assisted modification procedures in toluene and dime-thylformamide resulted in high reversibility of reactions on functionalised FLBP using a ferricyanide/ferrocya-nide...
-
Novel fast non-linear electrochemical impedance method for corrosion investigations
PublikacjaThe paper presents a novel approach to corrosion rate monitoring using non-linear electrochemical impedance spectroscopy. The authors propose a new variant of non-linear impedance measurement using amplitude-modulated multi-frequency ac perturbation signal. It allows shortening of measurement duration so it is possible to monitor corrosion rate of the systems experiencing rapid changes. In this way a limitation resulting from lack...
-
Optimization of the Relative Humidity of Reactant Gases in Hydrogen Fuel Cells Using Dynamic Impedance Measurements
PublikacjaWater management is a key factor affecting the efficiency of proton exchange membrane fuel cells (PEMFCs). The currently used monitoring methods of PEMFCs provide limited information about which processes or components that humidity has a significant impact upon. Herein, we propose the use of a novel approach of impedance measurements using a multi-sinusoidal perturbation signal, which enables impedance measurements under dynamic...
-
Partial inhibition of borohydride hydrolysis using porous activated carbon as an effective method to improve the electrocatalytic activity of the DBFC anode
PublikacjaCarbon materials are commonly used catalyst supports in various types of fuel cells. Due to the possibility of designing their properties, they seem to be attractive and functional additives. In Direct Borohydride Fuel Cells (DBFCs), the electrooxidation reaction of borohydride competes with the undesirable hydrolysis reaction, therefore our work aimed to modify anodes based on a multi-component hydrogen storage alloy with a small...
-
Polynomial description of dynamic impedance spectrogram—introduction to a new impedance analysis method
PublikacjaThis paper presents a polynomial description of spectrograms obtained using Dynamic Electrochemical Impedance Spectroscopy. A method to fit the polynomial degree correctly is discussed. A simple electrical system of a diode connected in parallel with a capacitor was used for testing. Dynamic impedance measurements during potentiodynamic polarization were conducted. This paper presents an alternative analysis method that allows...
-
Sodium nitrite as a corrosion inhibitor of copper in simulated cooling water
PublikacjaThe corrosion inhibition behavior of sodium nitrite (NaNO2) towards pure copper (99.95%) in simulated cooling water (SCW) was investigated by means of electrochemical impedance spectroscopy (EIS) and dynamic electrochemical impedance spectroscopy (DEIS). NaNO2 interferes with metal dissolution and reduce the corrosion rate through the formation or maintenance of inhibitive film on the metal surface. Surface morphologies illustrated...
-
Spectacular Oxygen Evolution Reaction Enhancement through Laser Processing of the Nickel‐Decorated Titania Nanotubes
PublikacjaThe selective, laser‐induced modification of the nickel‐decorated titania nanotubes provides remarkable enhancement toward oxygen evolution reaction. Particularly, the irradiation of the laterally spaced crystalline TiO2 nanotubes, results in the formation of the tight closure over irradiated end, preserving their hollow interior. The shape of the absorbance spectra is modulated along with applied energy, and the new absorption...
-
Studies on Aminoanthraquinone-Modified Glassy Carbon Electrode: Synthesis and Electrochemical Performance toward Oxygen Reduction
PublikacjaIn this paper, 9,10-anthraquinone (AQ) derivative-modified glassy carbon (GC) electrodes werestudied towards the electrochemical reduction of oxygen in aqueous and non-aqueous solutions. The reaction of 1-chloro-9,10-anthraquinone with aliphatic diamines was applied for the synthesis of amino-9,10-anthraquinone derivatives. The obtained AQ derivatives were grafted onto the surface of glassy carbon electrodes by electropolymerisation...
-
The Effect of Increasing the Amount of Indium Alloying Material on the Efficiency of Sacrificial Aluminium Anodes
PublikacjaAl-Zn-In alloys having 4.2% zinc content and various indium content in the range of 0.02–0.2% were tested with respect to the most important electrochemical properties of sacrificial anodes in a cathodic protection, i.e., the current capacity and potential of the operating anode. The distribution of In and Zn in the tested alloys was mapped by means of the EDX technique, which demonstrated that these elements dissolve well in the...
-
Ultrasonic-assisted Electrodeposition of Cu-Sn-TiO2 Nanocomposite Coatings with Enhanced Antibacterial Activity
PublikacjaCopper-based coatings are known for their high antibacterial activity. In this study, nanocomposite Cu–Sn–TiO2 coatings were obtained by electrodeposition from an oxalic acid bath additionally containing 4 g/dm3 TiO2 with mechanical and ultrasonic agitation. Ultrasound treatment was performed at 26 kHz frequency and 32 W/dm3 power. The influence of agitation mode and the current load on the inclusion and distribution of the TiO2...
Rok 2020
-
Adsorption behavior and corrosion inhibitive characteristics of newly synthesized cyano-benzylidene xanthenes on copper/sodium hydroxide interface: Electrochemical, X-ray photoelectron spectroscopy and theoretical studies
PublikacjaElegant process for synthesis of 3-(7H-dibenzo[c,h]xanthen-7-yl)benzaldehyde (3), as new starting material to create a set of novel xanthene analogues, 2-(3-(7H-dibenzo[c,h]xanthen-7-yl)benzylidene)malononitrile (4), 3-(3-(7H-dibenzo[c,h]xanthen-7-yl)phenyl)-2-cyanoacrylic acid (5), and Ethyl-3-(3-(7H-dibenzo[c,h]xanthen-7-yl)phenyl)-2-cyanoacrylate (6), was achieved starting with available materials under mild conditions. Various...
-
An integral-differential method for impedance determination of the hydrogen oxidation process in the presence of carbon monoxide in the proton exchange membrane fuel cell
PublikacjaThe impedance of a proton exchange membrane fuel cell powered by hydrogen contaminated with carbon monoxide, ranging from 150 to 300 ppb, is measured and discussed. The tested range of CO concentration complied with the fuel standard specified in the ISO standards. Studies of influence of CO contamination on operation of PEMFC are crucial for further development and commercialization of fuel cells for automotive applications. Based...
-
Application of BiOClnBrm photocatalyst to cytostatic drugs removal from water; mechanism and toxicity assessment
PublikacjaThe photocatalytic activity of series of BiOClnBrm photocatalysts toward degradation and mineralization of the cytostatic drugs 5-fluorouracil (5-FU) and imatinib mesylate (IMA) both singly and in their mixture under simulated solar and visible light irradiation has been investigated. Screening test revealed that among BiOClnBrm photocatalysts synthesized by a solvothermal method, the one with molar 1.3Cl/0.7Br ratio was the most...
-
Capacitance Enhancement by Incorporation of Functionalised Carbon Nanotubes into Poly(3,4-Ethylenedioxythiophene)/Graphene Oxide Composites
PublikacjaThis paper reports on the role of oxidised carbon nanotubes (oxMWCNTs) present in poly-3,4-ethylenedioxytiophene (PEDOT)/graphene oxide (GOx) composite. The final ternary composites (pEDOT/GOx/oxMWCNTs) are synthesised by an electrodeposition process from the suspension-containing monomer, oxidised carbon nanotubes and graphene oxide. Dissociated functional groups on the surface of graphene oxide play a role of counter-ions for the...
-
Cathodic activation of synthesized highly defective monoclinic hydroxyl‐functionalized ZrO2 nanoparticles for efficient electrochemical production of hydrogen in alkaline media
PublikacjaThe high electrochemical stability of Zirconia (ZrO2) at high potentials strongly suggested it as an alternative to carbon supports, which experience reduced efficiency due to some corrosion problems particularly during prolonged electrocatalysis activity. However, the use of ZrO2 was limited by its low electrical conductivity and surface area. In this work, we developed a methodology for synthesizing monoclinic ZrO2 NPs with increased...
-
Comparison of Cadmium Cd2+ and Lead Pb2+ Binding by Fe2O3@SiO2‐EDTA Nanoparticles – Binding Stability and Kinetic Studies
PublikacjaThis study describes the synthesis and characterization of ethylenediaminetetraacetic acid (EDTA) functionalized magnetic nanoparticles of 20 nm in size – Fe3O4@SiO2‐EDTA – which were used as a novel magnetic adsorbent for Cd(II) and Pb(II) binding in aqueous medium. These nanoparticles were obtained in two‐stage synthesis: covering by tetraethyl orthosilicate and functionalization with EDTA derivatives. Nanoparticles were characterized...
-
Correlation between partial inhibition of hydrogen evolution using thiourea and catalytic activity of AB5-type hydrogen storage alloy towards borohydride electrooxidation
PublikacjaDirect borohydride fuel cells (DBFCs) are devices which directly convert the chemical energy stored in the borohydride ion and oxidant into electrical energy as a result of redox reactions. Unfortunately, a significant amount of fuel is lost as a result of the undesirable hydrolysis reaction. The selection of an efficient borohydride hydrolysis inhibitor requires detailed knowledge regarding the interaction mechanism between the...
-
Corrosion hazards and inhibitor protection in the seawater injection system on the Baltic sea rig
PublikacjaOil extraction efficiency in LOTOS Petrobaltic Company is increased by means of injection of seawater into an oilfield aquifer, which is implemented on the Baltic Beta rig, operating on the Baltic Sea. Operational experience has shown a significant degree of corrosion aggressiveness in the injected water, which necessitates frequent repairs of the seawater injection installation. Evaluation of the corrosion phenomena is crucial...
-
Defective TiO2 Core-Shell Magnetic Photocatalyst Modified with Plasmonic Nanoparticles for Visible Light-Induced Photocatalytic Activity
PublikacjaIn the presented work, for the first time, the metal-modified defective titanium(IV) oxide nanoparticles with well-defined titanium vacancies, was successfully obtained. Introducing platinum and copper nanoparticles (NPs) as surface modifiers of defective d-TiO2 significantly increased the photocatalytic activity in both UV-Vis and Vis light ranges. Moreover, metal NPs deposition on the magnetic core allowed for the effective separation...
-
DETERMINATION OF THE EFFECT OF ENVIRONMENTAL FACTORS ON THE CORROSION OF WATER DISTRIBUTION SYSTEM BASED ON ANALYSIS OF ON-LINE CORROSION MONITORING RESULTS
PublikacjaCorrosion of water distribution system is a significant issue causing problems with quality, safety and continuity of distribution. The changes of corrosion rates of the water distribution systems in Cracow made of carbon steel were investigated by analysis of online corrosion monitoring system results. Corrosion rates were determined using the linear polarization method. The impact of rain, temperatures, conductivity, dissolved...
-
Differential analysis of dynamic immittance spectra
PublikacjaThis work presents a new approach to the analysis of immittance spectrograms of systems characterised by non-stationarity. The possibility of linking the evolution of the immittance response with changes in the parameters describing the system is achieved by introducing a spectrum in differential form. By using the above procedure, it becomes possible to separate elements with a dependence (or lack thereof) from an independent...
-
Efficient Method for the Concentration Determination of Fmoc Groups Incorporated in the Core-Shell Materials by Fmoc–Glycine
PublikacjaIn this paper, we described the synthesis procedure of TiO2@SiO2 core-shell modified with 3-(aminopropyl)trimethoxysilane (APTMS). The chemical attachment of Fmoc–glycine (Fmoc–Gly–OH) at the surface of the core-shell structure was performed to determine the amount of active amino groups on the basis of the amount of Fmoc group calculation. We characterized nanostructures using various methods: transmission electron microscope...
-
Electrochemical performance of thin free-standing boron-doped diamond nanosheet electrodes
PublikacjaIn the following work we describe preparation and the electrochemical performance of thin and free-standing heavy boron-doped diamond (BDD) nanosheets. The investigated foils were deposited on Ta substrate using microwave plasma-enhanced chemical vapor deposition technique (MPECVD). Foils of two B-dopant densities were investigated, obtained on the base of 10 k and 20 k ppm [B]/[C] ratio in the gas admixture. The obtained foils...
-
Electrochemical, theoretical and surface physicochemical studies of the alkaline copper corrosion inhibition by newly synthesized molecular complexes of benzenediamine and tetraamine with π acceptor
PublikacjaTwo charge transfer complexes, namely [(BDAH)+(PA−)] CT1 [(BTAH)2+(PA−)2] and CT2 (BDAH = 1,2-benzenediamine, BTAH = 1,2,4,5-benzenetetramine, and PA− = 2,4,6-trinitrophenolate), were synthesized and fully characterized using various spectroscopic techniques. CT1 and CT2 were tested as inhibitors to effectively control the uniform and anodic corrosion processes of copper in an alkaline electrolyte (1.0 M KOH) using various electrochemical...
-
Enhanced Charge Storage Mechanism And Long-Term Cycling Stability In Diamondized Titania Nanocomposite Supercapacitors Operating In Aqueous Electrolytes
PublikacjaThe long cycle life stability jointly with high energy density are limiting broader feasible applications of supercapacitors. The novel diamondized titania nanocomposite supercapacitors deliver high power and energy densities along with high capacitance retention rates. Supercapacitor electrodes were fabricated utilizing a combination of Ti anodization followed by chemical vapor deposition resulting in simultaneous growth of complex...
-
Failures and a concept of corrosion protection system for spiral classifiers at KGHM Polska Miedź S.A. Ore Concentration Plant
PublikacjaThe Ore Concentration Plant, where the process of flotation is carried out as well as the final production of copper concentrate, plays a key role in the entire production line of KGHM Polska Miedź S.A. Majority of operations related to the run-of-mine preparation to copper flotation enrichment are carried out in a water environment. The maintaining of production process continuity requires to pursue minimisation of many production...
-
Fault Diagnostics in PEMFC Stacks by Evaluation of Local Performance and Cell Impedance Analysis
PublikacjaStarvation, flooding, and dry‐out phenomena occur in polymer electrolyte membrane fuel cells (PEMFCs), due to heterogeneous local conditions, material inhomogeneity, and uneven flow distribution across the single cell active area and in between the individual cells. The impact of the load level and air feed conditions on the performance was identified for individual single cells within a 10‐cell stack. Analysis of the current density...
-
Formation of the hollow nanopillar arrays through the laser-induced transformation of TiO2 nanotubes
PublikacjaIn the following article, we present a simple, two-step method of creating spaced, hollow nanopillars, from the titania nanotube arrays via pulsed laser-treatment. Due to the high ordering of the structure, the prepared material exhibits photonic properties, which has been shown to increase the overall photoefficiency. The optical and morphological changes in the titania nanotubes after pulsed laser-treatment with 532, 355, and...
-
High-Temperature Oxidation of Heavy Boron-Doped Diamond Electrodes: Microstructural and Electrochemical Performance Modification
PublikacjaIn this work, we reveal in detail the effects of high-temperature treatment in air at 600 °C on the microstructure as well as the physico-chemical and electrochemical properties of boron-doped diamond (BDD) electrodes. The thermal treatment of freshly grown BDD electrodes was applied, resulting in permanent structural modifications of surface depending on the exposure time. High temperature affects material corrosion, inducing...
-
Intergranular Corrosion Detection Using Electromagnetic Transducers for Ultrasonic Testing
PublikacjaThe aim of this paper is to create a research methodology that allows a quick analysis of the structural state of high alloy austenitic steels using non-destructive ultrasonic tests, in contrast to destructive standard methods. Electromagnetic acoustic transducers (EMAT) are used to generate and receive the ultrasonic wave and detect the microstructural changes caused by sample sensitization in elevated temperature, even after...
-
Laser induced formation of copper species over TiO2 nanotubes towards enhanced water splitting performance
PublikacjaWe proposed fast and scalable route where the ordered TiO2 nanotubes coated with thin copper layers were annealed by the laser beam of 355 nm wavelength at different fluencies in the range of 15–120 mJ/cm2. As a result, copper species are integrated with the titania substrate and the formed material exhibits unique optical absorption bands in the visible range. Moreover, X-ray photoelectron spectroscopy analysis reveals the formation...
-
Laser-Assisted Synthesis and Oxygen Generation of Nickel Nanoparticles
PublikacjaNowadays, more than ever, environmental awareness is being taken into account when it comes to the design of novel materials. Herein, the pathway to the creation of a colloid of spherical, almost purely metallic nickel nanoparticles (NPs) through pulsed laser ablation in ethanol is presented. A complex description of the colloid is provided through UV-vis spectroscopy and dynamic light scattering analysis, ensuring insight into...
-
Modernized cathodic protection system for legs of the production rig – Evaluation during ten years of service
PublikacjaThe modernization of cathodic protection system of the Baltic Beta platform legs is described. It was that the sacrificial anodes cone-shaped groups were to be placed on the seabed at a depth of 80 m. The measurements results of cathodic protection effectiveness during its ten-years operation are presented. The effectiveness was assessed based on the potential value along the entire length of the legs from the sea surface to the...
-
Możliwości wykorzystania spektroskopii fotoelektronów w analizie jakości środowiska wodnego
PublikacjaSpektroskopia fotoelektronów w zakresie promieniowania X, (XPS, z ang. X-ray photoelectron spectroscopy) jest nowoczesną metodą analityczną wykorzystywaną w wielu wiodących ośrodkach naukowych na świecie. Jest ona stale ulepszana, jak też poznawane są nowe obszary jej zastosowania. W niniejszym artykule przedstawione zostały możliwości wykorzystania metody XPS w ramach obszarów badawczych powiązanych z gospodarką wodną, takich...
-
Multisine impedimetric probing of biocatalytic reactions for label-free detection of DEFB1 gene: How to verify that your dog is not human?
PublikacjaAlbert is a dog (Canis familiaris), but he does not realize this. Albert loves human food (and beer), watching movies on the internet, sleeping in bed, and more. But he should not do all these things. To convince him that, we have desinged a test procedure. The DEFB1 gene is unique to human species. Detecting its presence from saliva and in short periods may offer an advantage in the field of forensic medicine, and influence Albert’s...
-
Ni/cerium Molybdenum Oxide Hydrate Microflakes Composite Coatings Electrodeposited from Choline Chloride: Ethylene Glycol Deep Eutectic Solvent
PublikacjaCerium molybdenum oxide hydrate microflakes are codeposited with nickel from a deep eutectic solvent-based bath. During seven days of exposure in 0.05 M NaCl solution, the corrosion resistance of composite coating (Ni/CeMoOxide) is slightly reduced, due to the existence of some microcracks caused by large microflakes. Multielemental analysis of the solution, in which coatings are exposed and the qualitative changes in the surface...
-
Novel application of dynamic electrochemical impedance monitoring to a cataphoretic coating process
PublikacjaThe paper presents a novel method of on-line impedance monitoring of cataphoretic coating application process. Utilization of dynamic electrochemical impedance spectroscopy (DEIS) overcame the fundamental problem connected with non-stationarity of the aforementioned coating deposition process, which eliminates classical impedance spectroscopy technique from a real-time description of cataphoresis. The paper illustrates selected examples...
-
Obtaining and Characterization of the PLA/Chitosan Foams with Antimicrobial Properties Achieved by the Emulsification Combined with the Dissolution of Chitosan by CO2 Saturation
PublikacjaA new method of obtaining functional foam material has been proposed. The materials were created by mixing the poly lactic acid (PLA) solution in chloroform, chitosan (CS) dissolved in water saturated with CO2 and polyethylene glycol (PEG), and freeze-dried for removal of the solvents. The composite foams were characterized for their structural (SEM, FT-IR, density, porosity), thermal (DSC), functional (hardness, elasticity, swelling...
-
Ocena zagrożenia korozyjnego zbiorników na terenie modernizowanego Terminala Paliw LOTOS w Piotrkowie Trybunalskim.
PublikacjaZbadano zagrożenie korozyjne nowo budowanych zbiorników na terenie modernizowanego terminala paliw. Oceny dokonano na podstawie badań agresywności korozyjnej pobranych próbek gruntu oraz wykonanych pomiarów terenowych. Uzyskane wyniki będą wykorzystane przy projektowaniu systemu ochrony katodowej nowych zbiorników podziemnych.
-
Określenie przyczyn korozji śrub napędowych ORP Drużno.
PublikacjaPrzedmiotem ekspertyzy było określenie przyczyn korozji śrub napędowych na okręcie ORP Drużno oraz wskazanie zaleceń odnośnie ograniczenia czynników powodujących ich korozję.
-
One-step recovery of REE oxalates in electro-leaching of spent NdFeB magnets
PublikacjaRecovery of rare-earth elements (REEs) from spent NdFeB magnets is receiving great attention because of high amount of neodymium and potential risk of environmental pollution. In this study, a novel environment-friendly hydrometallurgical route is proposed for efficient recovery of REEs during electrochemical leaching with sulfuric and oxalic acids. With proper adjustment of the electrolyte composition and operating conditions,...
-
Performance of organic coatings upon cyclic mechanical load
PublikacjaA number of engineering structures fail due to the fatigue damage resulting from cyclic mechanical stress. However, as far as organic coatings are concerned this degradation factor remains underestimated. In the paper the authors propose a methodology combining global electrochemical impedance spectroscopy and local atomic force microscopy measurements for evaluation of coating resistance to an impact of repetitive mechanical stress. Typical...
-
Podstawowe procedury pomiarowe w ochronie katodowej
PublikacjaOpracowanie zawiera opis podstawowych procedur pomiarowych stosowanych przez personel ochrony katodowej w sektorze lądowych konstrukcji metalowych. Znajomość opisanych metod jest wymagana od personelu na poziomie 1 oraz na poziomie 2 kompetencji zgodnie z wymogami normy PN-EN ISO 15257:2017-10: "Ochrona katodowa -- Poziomy kompetencji osób zajmujących się ochroną katodową -- Podstawa systemu certyfikacji". Opracowanie przeznaczone...
-
Pomiary terenowe i analiza techniczna stopnia agresywności korozyjnej gruntu w Bazie PERN S.A. Adamowo.
PublikacjaW ramach realizacji pracy pobrano próbki gruntu na terenie bazy paliw i wykonano na nich analizy fizyko-chemiczne, na podstawie których określono agresywność korozyjną gruntu na terenie bazy. Uzyskane wyniki będą wykorzystane przy projektowaniu zabezpieczeń przeciwkorozyjnych obiektów na terenie bazy paliw.
-
Pomiary terenowe i analiza techniczna stopnia agresywności korozyjnej gruntu w Bazie PERN S.A. Gdańsk
PublikacjaW ramach realizacji pracy pobrano próbki gruntu na terenie bazy paliw i wykonano na nich analizy fizyko-chemiczne, na podstawie których określono agresywność korozyjną gruntu na terenie bazy. Uzyskane wyniki będą wykorzystane przy projektowaniu zabezpieczeń przeciwkorozyjnych obiektów na terenie bazy paliw.
-
Pomiary terenowe i analiza techniczna stopnia agresywności korozyjnej gruntu w Bazie PERN S.A. Miszewko Strzałkowskie
PublikacjaW ramach realizacji pracy pobrano próbki gruntu na terenie bazy paliw i wykonano na nich analizy fizyko-chemiczne, na podstawie których określono agresywność korozyjną gruntu na terenie bazy. Uzyskane wyniki będą wykorzystane przy projektowaniu zabezpieczeń przeciwkorozyjnych obiektów na terenie bazy paliw.
-
Preparation and Characterization of Defective TiO2. The Effect of the Reaction Environment on Titanium Vacancies Formation
PublikacjaAmong various methods of improving visible light activity of titanium(IV) oxide, the formation of defects and vacancies (both oxygen and titanium) in the crystal structure of TiO2 is an easy and relatively cheap alternative to improve the photocatalytic activity. In the presented work, visible light active defective TiO2 was obtained by the hydrothermal reaction in the presence of three different oxidizing agents: HIO3, H2O2, and...
-
Protective and Suppressing Electromagnetic Interference Properties of Epoxy Coatings Containing Nano-Sized NiZn Ferrites
PublikacjaNano-crystalline ferrites with the chemical formula NixZn(1−x)Fe2O4, where x = 0, 0.2, 0.4, 0.6, 0.8, 1.0, were synthesized using a co-precipitation method. The obtained ferrites were investigated by X-ray diffraction (XRD). The corrosion inhibiting behavior of nano-sized ferrites was tested using carbon steel samples and 10% aqueous ferrite extracts. Results were compared with previous data obtained for micro-sized ceramic ferrites....