Wyszukiwarka
Katedra Technologii Maszyn i Automatyzacji Produkcji
Publikacje
Filtry
wszystkich: 801
Katalog Publikacji
Rok 2024
-
Analysis of Roughness, the Material Removal Rate, and the Acoustic Emission Signal Obtained in Flat Grinding Processes
PublikacjaIn this work, the analysis of the acoustic emission (AE) signal in grinding processes is addressed. The proposed analysis method decomposes the acoustic signal into three frequency ranges. The total energy of each range is determined, as well as the highest frequency. Different grinding experiments were carried out, according to a full factorial design of experiments (DOE), in which feed speed, depth of cut, and transversal step...
Rok 2023
-
Influence of Honing Parameters on the Quality of the Machined Parts and Innovations in Honing Processes
PublikacjaThe article presents a literature review dealing with the effect of the honing parameters on the quality of the machined parts, as well as with the recent innovations in honing processes. First, an overview about the honing and the plateau-honing processes is presented, considering the main parameters that can be varied during machining. Then, the influence of the honing parameters on surface finish, shape deviation and material...
-
Modeling of Surface Roughness in Honing Processes by UsingFuzzy Artificial Neural Networks
PublikacjaHoning processes are abrasive machining processes which are commonly employed to improve the surface of manufactured parts such as hydraulic or combustion engine cylinders. These processes can be employed to obtain a cross-hatched pattern on the internal surfaces of cylinders. In this present study, fuzzy artificial neural networks are employed for modeling surface roughness parameters obtained in finishing honing operations. As...
-
Multi-objective optimization of tool wear, surface roughness, and material removal rate in finishing honing processes using adaptive neural fuzzy inference systems
PublikacjaHoning processes are usually employed to manufacture combustion engine cylinders and hydraulic cylinders. A crosshatch pattern is obtained that favors the oil flow. In this paper, Adaptive Neural Fuzzy Inference System (ANFIS) models were obtained for tool wear, average roughness Ra, cylindricity and material removal rate in finish honing processes. In addition, multi-objective optimization with the desirability function method...
Rok 2021
-
A pilot study to assess manufacturing processes using selected point measures of vibroacoustic signals generated on a multitasking machine
PublikacjaThe article presents the method for the evaluation of selected manufacturing processes using the analysis of vibration and sound signals. This method is based on the use of sensors installed outside the machining zone, allowing to be used quickly and reliably in real production conditions. The article contains a developed measurement methodology based on the specific location of microphones and vibration transducers mounted on...
-
Analiza gładzenia otworów walcowych przy zmiennych warunkach kinematycznych
PublikacjaW pracy zweryfikowano wpływ parametrów obróbki na przebieg procesu gładzenia i stwierdzono, że metodą umożliwiającą uzyskanie zarówno dobrej jakości powierzchni jak i niższej o 35,2% temperatury przedmiotu gładzonego oraz mniejszej o 12,77% odchyłki walcowości (w porównaniu do gładzenia tradycyjnego) jest gładzenie ze zmienną kinematyką. Zmienny...
-
Experimental research of the effect of face milling strategy on the flatness deviations
PublikacjaIn this paper the dependencies between face milling strategy of EN AW6082-T6 aluminum alloy samples, with difference thicknesses (6, 8, and 12 mm) and two cold rolling directions, and flatness deviations were presented. Three strategies of milling included different proportions of material removed from both sides of the plates. This approach allowed to control the proportions of residual surface stresses on both sides of the specimens,...
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublikacjaThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 1/2
PublikacjaWind power plants are considered as ecologically-clean source of energy. However, manufacturing processes cannot be treated that way. Manufacturing processes consume huge amount of electrical and thermal energy and significant amount of materials, e.g. steel, polymers, oils and lubricants. All of the above could be potentially harmful for environment. There are not many works and publications regarding life-cycle analysis of wind...
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 2/2
PublikacjaThe process of conversion of wind kinetic energy into electricity in innovative wind power plant emits practically no harmful substances into the environment. However, the production stage of its components requires a lot of energy and materials. The biggest problem during production plan-ning process of an innovative wind power plant is selection of materials and technologies and, consequently, the waste generated at this stage....
-
Opinia na temat celowości oraz zakresu rzeczowego remontu tokarki karuzelowej FKD-60/80. Ekspertyza techniczna opracowana na zlecenie ENEROMONTAŻ-PÓŁNOC GDYNIA S.A.
PublikacjaOpracowana Opinia Jednostki Naukowej dotyczyła ciężkiej tokarki karuzelowej typu FKD-60/80 ze sterowaniem CNC. Na podstawie przeprowadzonego w miejscu użytkowania tej obrabiarki audytu, dokonano oceny obecnego stanu maszyny oraz przeanalizowano przyczyny awarii, które zdarzały się w okresie jej eksploatacji. Zakres analizy przyczyn stanów awaryjnych obejmował: - awarie zespołu elektrowrzeciona oraz układów hydraulicznych zawartych...
-
Opinia na temat celowości oraz zakresu rzeczowego remontu wytaczarko-frezarki płytowej typu FLF16/CNC. Ekspertyza techniczna opracowana na zlecenie ENEROMONTAŻ-PÓŁNOC GDYNIA S.A.
PublikacjaOpracowana Opinia Jednostki Naukowej dotyczyła ciężkiej wytaczarko-frezarki płytowej typu FLF16/CNC ze sterowaniem CNC. Na podstawie przeprowadzonego w miejscu użytkowania tej obrabiarki audytu, dokonano oceny obecnego stanu maszyny oraz przeanalizowano przyczyny awarii, które zdarzały się w okresie jej eksploatacji. Zakres analizy przyczyn problemów eksploatacyjnych i stanów awaryjnych obejmował: - awarie zespołu elektrowrzeciona...
-
Wpływ sposobu suszenia na wiązkość i naprężenia tnące przy przecinaniu wybranych gatunków drewna
PublikacjaW rozprawie doktorskiej przedstawiono wpływ sposobów suszenia na wiązkość i naprężenia tnące w strefie skrawania, które zgodnie ze współczesną mechaniką pękania można uznać za energetyczne wskaźniki skrawalności. Badania zostały przeprowadzone dla próbek z drewna sosnowego (Pinus sylvestris L.) i bukowego (Fagus silvatica L.) suszonego czterema sposobami. Trzy z nich, to najczęściej wykorzystywane w przemyśle, suszenie w sposób...
Rok 2020
-
45 lat minęło - kolejne spotkanie technologów na Wydziale Mechanicznym
PublikacjaOmówiono przebieg Jubileuszowego Zjazdu Absolwentów Wydziału Mechanicznego Politechniki Gdańskiej, którzy ukończyli studia wiosną i jesienią w roku 1974.
-
A Critical Reanalysis of Uncontrollable Washboarding Phenomenon in Metal Band Sawing
PublikacjaThe article analyzes the cutting process of hard bars. Investigations conducted in industrial conditions demonstrated the presence of surface errors in the machined workpieces in the form of washboard patterns. The purpose of this study was to analyze the results of cutting on band sawing machines with different band saw blades. The cutting processes were conducted on three different horizontal band sawing machine types. Analyzed...
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublikacjaPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
Absolwent Wydziału Mechanicznego Złotym Inżynierem "Przeglądu Technicznego"
PublikacjaPrzedstawiono sylwetke i dorobek mgr. inż. Janusza Ochocińskiego, tegorocznego laureata plebiscytu czasopima "Przegląd Techniczny", o tytuł Złotego Inżyniera 2019 w kategorii Menedżer. Pan Janusz Ochociński jest absolwentem Wydziału Mechanicznego Technologicznego Politechniki Gdańskiej z roku 1981.
-
Analiza ilościowa technologiczności konstrukcji oprzyrządowania obróbkowego - studium przypadku
PublikacjaOmówiono ilościową metodę oceny technologiczności konstrukcji oprzyrządowania obróbkowego. Przedstawiono przykład oceny technologiczności zaprojektowanych trzech wersji uchwytów wiertarskich w procesie technologicznym części klasy dźwignia
-
Analysis of flat compensator lapping in an assembly process
PublikacjaPrzedstawiono sposób analizy docierania kompensatora płaskiego podczas montażu połączenia konstrukcyjnego. Wyznaczono czas główny obróbki i koszty operacji docierania jednotarczowego
-
Application of 3D printing metal powder technology in the manufacture of components with complex geometries
PublikacjaThe possibilities of using 3D printing powder technologies for making objects with complex geometries were presented. For this purpose, selected examples of elements with different geometries were used, which were built using metal powder methods – DMLS (direct metal laser sintering) / SLM (selective laser melting). Simultaneously, the indicated elements concern those areas of industry where 3D printing technology has been widely...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublikacjaIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Deformation and Surface Color Changes of Beech and Oak Wood Lamellas Resulting from the Drying Process
PublikacjaThe drying process was examined relative to parameters’ influence on the deformation and surface layer color changes of beech wood (Fagus sylvatica L.) and oak wood (Quercus robur L.). The goal was to analyze the impact of drying process conditions, wood and growth rings types, and load on the deformation and surface color changes of drying thin wooden elements. A further aim was to reduce the time of the lamella drying and minimize...
-
Druk 3D części z tworzyw sztucznych na skalę przemysłową w technologii SLS
PublikacjaFirma EOS, wiodący i światowy dostawca technologii przemysłowego wykorzystania druku 3D dla materiałów metalicznych i polimerowych, zaprezentowała na targach formnext 2017 nowy system EOS P500, przeznaczony do addytywnego wytwarzania modeli. Drukarka 3D adresowana jest dla przedsiębiorstw chcących wytwarzać na skalę przemysłową części i elementy z tworzyw sztucznych o wysokiej jakości.
-
Druk 3D części z tworzyw sztucznych na skalę przemysłową w technologii SLS
PublikacjaFirma EOS, wiodący i światowy dostawca technologii przemysłowego wykorzystania druku 3D dla materiałów metalicznych i polimerowych, zaprezentowała na targach formnext 2017 nowy system EOS P500, przeznaczony do addytywnego wytwarzania modeli. Drukarka 3D adresowana jest dla przedsiębiorstw chcących wytwarzać na skalę przemysłową części i elementy z tworzyw sztucznych o wysokiej jakości.
-
E-dyplomy: uwarunkowania administracyjne i funkcjonalne ich wprowadzenia na polskich uczelniach
PublikacjaPandemia COVID-19 wymusiła na polskim systemie szkolnictwa wyższego szereg zmian, z których główne dotyczą zmian w zakresie organizacji pracy, cyfryzacji procesów obsługi toku studiów. Przepisy prawa stanowią już o e-teczce, mamy rozporządzenia dotyczące jej prowadzenia, niemniej niewiele uczelni, o ile w ogóle, prowadzi na chwilę obecną akta osobowe studentów w postaci elektronicznej. Jednym z elementów składowych e-teczki jest...
-
Effect of electrode waterproof coating on quality of underwater wet welded joints
PublikacjaIn this paper, the effects of different hydrophobic coatings on the surface of covered electrodes on the quality of wet welded carbon steel joints were discussed. Commonly available hydrophobic substances used in industrial applications were selected for the research. The aim of using waterproof coatings was to check the possibility to decreasing the susceptibility of highstrength low-alloy S460N steel to cold cracking. During...
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublikacjaThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
Effect of the Drying Method of Pine and Beech Wood on Fracture Toughness and Shear Yield Stress
PublikacjaThe modern wood converting processes consists of several stages and material drying belongs to the most influencing future performances of products. The procedure of drying wood is usually realized between subsequent sawing operations, affecting significantly cutting conditions and general properties of material. An alternative methodology for determination of mechanical properties (fracture toughness and shear yield stress) based...
-
Effect of Thermal Treatment of Birch Wood by Saturated Water Vapor on Granulometric Composition of Chips from Sawing and Milling Processes from the Point of View of Its Processing to Composites
PublikacjaThe goal of this work is to investigate the impact of thermal modification of birch wood with saturated steam on the particle size distribution of the sawing and milling process. Birch wood (Betula pendula Roth) is an excellent source to produce plywood boards. Wastes from mechanical processing of birch wood are suitable to produce composite materials. Granulometric analyses of chips from sawing processes on the PRW 15M frame saw,...
-
Innovative rehabilitation lifts – mechanics in medical devices
PublikacjaMechanical devices are now widely used in physiotherapy and other rehabilitation processes. Particular importance is attached to devices enabling easy and effective transport of disabled people. The article presents innovative designs of rehabilitation lifts offered by the Polish manufacturer of lifts and medical accessories, LeviCare company. Moreover, the main assumptions of the research and development project implemented by...
-
MULTI-CRITERIA COMPARATIVE ANALYSIS OF THE USE OF SUBTRACTIVE AND ADDITIVE TECHNOLOGIES IN THE MANUFACTURING OF OFFSHORE MACHINERY COMPONENTS
PublikacjaThe dynamic development of additive manufacturing technologies, especially over the last few years, has increased the range of possible industrial applications of 3D printed elements. This is a consequence of the distinct advantages of additive techniques, which include the possibility of improving the mechanical strength of products and shortening lead times. Offshore industry is one of these promising areas for the application...
-
Nagrzewanie się elementów układu obróbkowego w docieraniu powierzchni płaskich
PublikacjaPrzedstawiono analizę temperatury elementów układu wykonawczego docierarki jednotarczowej przy użyciu kamery termowizyjnej. W badaniach stosowano różne wartości prędkości obrotowej tarczy docierającej oraz dwa zakresy ziarnistości mikroziaren ściernych w dozowanej paście. Obrabiano elementy płaskie wykonane ze stali chromowo - niklowej oraz brązu berylowego.
-
On-line measurement of wood surface smoothness
PublikacjaThe latest progress in the field of optics and microelectronics resulted in development of new generation vision systems capable of scanning surface topography with very high sampling frequencies. The blue color of illuminating light as well as novel systems for controlling ultra-thin laser line thickness allows measurement of the porous surface of wood with a triangulation method. Three alternative sensors were tested here in...
-
Opportunities and challenges for exploiting drones in agile manufacturing systems
PublikacjaDrones have become an advanced supply chain implementation instrument, especially in connecting warehouses to outlet points or even individual customers. However, their potential application in an intra-logistics framework has not been studied, let alone explored so far. Modeling and simulations in virtual environments can help explore and evaluate the opportunities for practical and profitable applications of drones in manufacturing...
-
Podstawy technologii selektywnego spiekania laserowego proszków polimerowych – SLS
PublikacjaW pracy zaprezentowano zbiór informacji oraz praktycznych wskazówek związanych z drukowaniem elementów metodą selektywnego spiekania laserowego proszków polimerowych – SLS. Zawarte treści dotyczą omówienia zasady działania, charakterystyki poszczególnych czynników procesu oraz powszechnie stosowanych materiałów. Przedstawiono ponadto najważniejsze korzyści i ograniczenia związane z wykorzystaniem metody SLS.
-
Pomiary temperatury podczas gładzenia otworów
PublikacjaPrzedstawiono wyniki badań temperatury podczas gładzenia otworów w elementach stalowych. Analizowano obróbkę otworów o średnicach 75H7, 75H10 i 150H7 mm. W badaniach zastosowano metodę termowizyjną. Otrzymane wyniki pomiarów pozwolą właściwie zaplanować miejsce i czas kontroli.
-
Predicting cutting power for band sawing process of pine and beech wood dried with the use of four different methods
PublikacjaWood drying is an important stage in the woodworking process. After drying, wood is subject to a re-sawing process, for which a high quality surface, low material loss, and high efficiency are often required. In this paper, forecasted values were presented of cutting power for the re-sawing process of pine and beech wood that were dried with four different methods. Forecasting of cutting power for an industrial band saw machine...
-
Revisiting the estimation of cutting power with different energetic methods while sawing soft and hard woods on the circular sawing machine: a Central European case
PublikacjaIn the classical approaches, used in Central Europe in practice, cutting forces and cutting power in sawing processes of timber are commonly computed by means of the specific cutting resistance kc. It needs to be highlighted that accessible sources in handbooks and the scientific literature do not provide any data about wood provenance, nor about cutting conditions, in which cutting resistance has been empirically determined. In...
-
Studying the Effect of Working Conditions on WEDM Machining Performance of Super Alloy Inconel 617
PublikacjaWire electrical discharge machining (WEDM) has been for many years a precise and efficient non-conventional manufacturing solution in various industrial applications, mostly involving the use of hard-to machine materials like, among other, the Inconel super alloys. The focus of the present study is on exploring the effect of selected control parameters, including pulse duration, pulse-off time and the dielectric flow pressure on...
-
The Design Development of the Sliding Table Saw Towards Improving Its Dynamic Properties
PublikacjaCutting wood with circular saws is a popular machining operation in the woodworking and furniture industries. In the latter sliding table saws (panel saws) are commonly used for cutting of medium density fiberboards (MDF), high density fiberboards (HDF), laminate veneer lumber (LVL), plywood and chipboards of different structures. The most demanded requirements for machine tools are accuracy and precision, which mainly depend on...
-
THE EFFECT OF DRYING INTENSITY ON THE COLOR CHANGES OF PINE WOOD (PINUS SYLVESTRIS L.)
PublikacjaThe effect of the selection of drying process parameters on the color change of Scots pine wood (Pinus Sylvestris L.) is presented. In this work the experimental studies have been performed. The research focused on the influence of drying intensity on the changes of color after drying process. Intensity of drying process was determined on the basis of the average drying gradient. To determine the color of wood before and after...
-
THE EFFECT OF LOG SORTING STRATEGY ON THE FORECASTED LUMBER VALUE AFTER SAWING PINE WOOD
PublikacjaThe optimal transformation path for the resource is determined by the quality of a log combined with its dimension. The commercial value of derived products is also closely connected with the size and extent of containing wood deficiencies. The results of studies with three diverse strategies for log sorting are presented in the paper. Resource assessment by a worker without extensive experience in sorting logs, the certified grading...
-
The Influence of the Depth of Cut in Single-Pass Grinding on the Microstructure and Properties of the C45 Steel Surface Layer
PublikacjaThe paper contains the results of a metallographic examination and nanoindentation test conducted for the medium carbon structural steel with low content of Mn, Si, Cu, Cr, and Ni after its grinding to a depth ranging from 2 μm to 20 μm, at constant cutting speed (peripheral speed) of vs = 25 ms−1 and constant feed rate of vft = 1 m/min. Applied grinding parameters did not cause the surface layer hardening, which could generate...
-
Theoretical and Actual Feed Per Tooth During Wood Sawing on an Optimizing Cross-Cut Saw
PublikacjaThe work presents the geometries of circular saw teeth, whose task is to divide the cross-cut of the cutting layer. For efficient machining on a cross-cut saw with high feed speed values (about 1 ms−1) maximal theoretical feeds per tooth are determined. These values were compared with the actual values determined during transverse cutting of pine wood on a special test stands in industrial conditions. In the experiment the rotational...
-
Thickness accuracy of sash gang sawing
PublikacjaThin lamellae, corresponding to the layer components of structural glued members, i.e. 2-ply or 3-ply glued parquet, can be manufactured in re-sawing operations of kiln-dried wood blocks. These must be prepared with high dimensional accuracy and adequate surface quality following specific technical requirements for lamellae thickness variations, especially in the upper layers of the glued composite parquet. The accuracy of oak...
-
Tool Wear Prediction in Single-Sided Lapping Process
PublikacjaSingle-sided lapping is one of the most effective planarization technologies. The process has relatively complex kinematics and it is determined by a number of inputs parameters. It has been noted that prediction of the tool wear during the process is critical for product quality control. To determine the profile wear of the lapping plate, a computer model which simulates abrasive grains trajectories was developed in MATLAB. Moreover,...
-
Unlocking creativity with new technologies
PublikacjaArtificial intelligence, augmented and virtual reality, Internet of Things and digital twins are just a few concepts related to the fourth industrial revolution that is happening right before our eyes. The key question asked by managers in the aerosol sector recently is: what does all this new technology mean to me?
-
Wear of electroplated diamond tools in lap-grinding of Al2O3 ceramic materials
PublikacjaCurrent development of modern products, together with ever-increasing demands for their operation and usage, necessitate the search for new processing methods. Abrasive machining is widely used in many industrial areas, especially for processing difficult-to-machine materials such as advanced ceramics. Grinding with lapping kinematics, also called lap-grinding, is still one of the innovative methods of abrasive processing being...
-
Wpływ rozmieszczenia elementów w separatorach na warunki kinematyczne docierania jednotarczowego
PublikacjaPrzedstawiono wyniki analiz kinematyki docierania elementów płaskich na docierarkach jednotarczowych o standardowym układzie wykonawczym. Określono wpływ rozmieszczenia elementów obrabianych w separatorach na zmienność prędkości docierania.
-
Wpływ rozmieszczenia elementów w separatorach na warunki kinematyczne docierania jednotarczowego
PublikacjaW rozdziale monografii naukowej przedstawiono wyniki analiz kinematyki docierania elementów płaskich na docierarkach jednotarczowych o standardowym układzie wykonawczym. Określono wpływ rozmieszczenia elementów obrabianych w separatorach na zmienność prędkości docierania. W przeprowadzonej symulacji wykorzystano wybrane modele docierarek firmy Kemet, analizując obróbkę dwóch elementów o zróżnicowanych wymiarach gabarytowych i zarysie...