Search
dr inż. Natalia Korcz-Konkol
Employment
- Assistant professor at Department of Engineering Structures
Publications
Filters
total: 9
Catalog Publications
Year 2023
-
Truss imperfections in the design of bar and diaphragm bracing systems
PublicationIn the article three variants of roof bracing were considered: bar bracing, diaphragm bracing and the combination of bar and diaphragm bracing. Different analytical and numerical ways of taking into account the imperfections of the truss girder were compared. The entire 3D model of the roof (shell and beam elements with the eccentricities taken into account) was analysed numerically. Selected stressed-skin aspects were considered....
Year 2021
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublicationIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublicationIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
Year 2020
-
Corrugated Sheeting as a Member of a Shear Panel Under Repeated Load—Experimental Test
PublicationIn stressed-skin design, the cladding stiffening effect on structures is taken into account. However, the “traditional” design is more usual, wherein this effect is neglected. Even if the diaphragm actions are not regarded, in particular cases such as big sheds (and others), the parasitic (unwanted) stressed-skin action may occur with the result of leakage or even failure. The structures of this kind have already been built. Thus,...
Year 2019
-
Influence of steel brackets supporting crane runway girders structure on the stress distribution in the brackets
PublicationThe paper presents a numerical analysis of steel brackets supporting a double-span crane runway girders. The purpose of the study was to assess the new structural solution based on the stress distribution in the brackets. In order to simplify the connection, the bottom flange of the crane runway girder is based directly on the upper flange of the bracket. As a result, the support reaction is no longer applied in the plane of the...
Year 2018
-
Influence of fasteners and connections flexibility on deflections of steel building including the stressed skin effect
PublicationThe paper presents the analysis of the influence of fasteners and connections flexibility on displacements of symmetrical single-bay pitched-roof steel building, including trapezoidal cladding acting as a diaphragm. The purpose of the article was to compare numerical models with and without taking into consideration fasteners and connections flexibility in order to observe the differences in transverse stiffness of the building...
-
Influence of sheet/purlin fasteners spacing on shear flexibility of the diaphragm
PublicationThe paper presents the influence of sheet/purlin fasteners location (in reference to trapezoidal profile cross section) on shear flexibility of the cladding acting as a diaphragm. Analytical procedures were presented and their limitations were discussed. Next, selected schemes of fasteners location, known from engineering practice, but not included in European codes and recommendations, were analysed numerically in order to observe...
-
Stability of roof trusses stiffened by trapezoidal sheeting and purlins
PublicationIn the article linear buckling analysis of a set of steel trusses braced by purlins and trapezoidal sheeting are conducted. The buckling load factor due to the height of a corrugated sheeting profile is investigated in parametric studies. The minimal height of trapezoidal sheeting required for preventing the sheeting and chords of the trusses against the buckling is obtained. Two groups of models are considered: “axial” model as...
Year 2017
-
Modele numeryczne uwzględniające tarczową pracę pokrycia dachowego z blach trapezowych
PublicationW artykule porównano wybrane sposoby uwzględniania w modelowaniu numerycznym tarczowej pracy pokrycia dachowego z blachy trapezowej, możliwe do zrealizowania w programie Autodesk Robot Structural Analysis Professional 2015, w celu oceny słuszności stosowania ich do obliczeń konstrukcji nośnej współpracującej z poszyciem z blachy trapezowej. Analizy przeprowadzono dla pojedynczej przepony. Za pomocą powłokowych elementów skończonych...
seen 2323 times