Search
prof. dr hab. inż. Michał Wasilczuk
Employment
- Head of Section at Zakład Konstrukcji Maszyn i Inzynierii Medycznej
- Vice-Dean for Scientific Research at Faculty of Mechanical Engineering and Ship Technology
- Kierownik Studium Doktoranckiego at Faculty of Mechanical Engineering and Ship Technology
Research fields
Publications
Filters
total: 84
Catalog Publications
Year 2024
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublicationIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
Year 2023
-
Ecology In Tribology: Selected Problems of Eliminating Natural Oil-Based Lubricants from Machine Friction Couples
PublicationThe elimination of mineral oil-based lubricants from machines has multiple beneficial effects on the natural environment. Firstly – these lubricants are a direct threat to the environment in the event of leaks; secondly – their elimination reduces the demand for crude oil from which they are obtained. In addition, in many cases, e.g. when replacing traditional lubricants with water, friction losses in the bearings can also be reduced...
-
Experimental Verification of the CFD Model of the Squeeze Film Lifting Effect
PublicationAbstract: The presented study shows the results of the research into the squeeze film levitation phenomena. The system introduced in the investigation is composed of a vibrating surface, air squeeze film, and the surface of the body freely suspended over the film. The use of the CFD (Computational Fluid Dynamics) model used in the system allows us to determine the steady state, periodic behavior of the air film (described by Navier–Stokes,...
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublicationThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublicationThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
Year 2020
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublicationThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
Year 2019
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublicationIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
Year 2018
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublicationDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
Ecological bearing systems for water turbines – research and development at Gdansk University of Technology
PublicationIncreasing requirements for environmental protection make it necessary to introduce new materials and designs. Hydroelectric power plants operating in direct contact with water reservoirs and rivers are potentially endangering water cleanliness, hence they should also be modernized in the way minimizing the environmental hazards. A lot of progress in this field has been achieved in last decades, but still there is much work to...
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublicationIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublicationIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
Improvement of Thrust Bearing Calculation Considering the Convectional Heating within the Space between the Pads
PublicationA modern thrust bearing tool is used to estimate the behavior of tilting pad thrust bearings not only in the oil film between pad and rotating collar, but also in the space between the pads. The oil flow in the space significantly influences the oil film inlet temperature and the heating of pad and collar. For that reason, it is necessary to define an oil mixing model for the space between the pads. In the bearing tool, the solutions...
-
The use of plate springs for preloading of a system of tapered roller bearings of a wind turbine gearbox
PublicationThe use of preloaded tapered roller bearings in wind turbine drive systems allows a transfer of load in the case of high variations of axial forces. The examined bearing system, a modification of a current design, consists of a pair of different sized bearings. Previous study showed the high sensitivity of tapered roller bearings on the existing radial interference. Dimensional tolerances used in the original design do not allow...
Year 2017
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Improvement of the thrust bearing calculation considering the convectional heating within the space between the pads
PublicationA modern thrust bearing calculation tool should consider not only the oil film between pad and rotating collar but also the space between the pads. The oil flow in the space has a significant influence on the oil film inlet temperature, the convectional cooling of pad and collar and should be included in the bearing calculation methods. The authors use a tool developed at Clausthal University of Technology in cooperation with the...
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublicationIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublicationA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
Year 2016
-
ANALYSIS OF THE POSSIBILITIES OF HIGH SPEED SHAFT BEARING SYSTEM DURABILITY INCREASE
PublicationDuring the operation of wind turbines with a gearbox of traditional configuration, a high failure rate of high-speed shaft bearings is observed. Such a high failures frequency is not reflected in standard bearing durability calculation methods, which can be attributed to atypical failure mechanism. To avoid observed problems in the 1.5 MW wind turbine, the modification of the existing bearing system is proposed. Multiple options,...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublicationHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
The effect of the exposure-in-oil on the contact of the polymers forming sliding layers in hydrodynamic bearings. Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych.
PublicationPolimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić...
Year 2015
-
BEARING SYSTEMS OF WIND TURBINES – MAINTENANCE PROBLEMS
PublicationW praktyce eksploatacyjnej turbin wiatrowych o tradycyjnej konstrukcji (przekładniowych) obserwowana jest duża awaryjność przekładni, a zwłaszcza łożysk tocznych szybkoobrotowych wałów przekładni. W Polsce na zlecenie właściciela dużej farmy wiatrowej, firmy Energa Wytwarzanie S.A., Politechnika Gdańska we współpracy z Politechniką Poznańską i Akademią Górniczo Hutniczą podjęły badania mające na celu diagnozowanie przyczyn uszkodzeń...
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublicationExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Compliance tests of the polymer layers used as hydrodynamic bearing coatings
PublicationOperational experience and scientific investigations results showed that polymer lined hydrodynamic bearings can withstand more severe operating conditions compared than white metal bearings. PTFE and PEEK-based coatings are the most frequently used as Babbitt alternatives. Both polymers differ significantly from the each other in material properties. According to catalogue data compression modulus of PTFE, it is about an order...
-
Drivetrain of a Wind Turbine
PublicationIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplying gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublicationHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Friction and Lubrication of Large Tilting-Pad Thrust Bearings
PublicationFluid film bearings have been extensively used in the industry because of their unbeatable durability and extremely low friction coefficient, despite a very low coefficient of friction dissipation of energy being noticeable, especially in large bearings. Lubricating systems of large tilting pad thrust bearings utilized in large, vertical shaft hydrogenerators are presented in this paper. A large amount of heat is generated due...
-
Scientific research in the Department of Machine Design and Automotive Engineering
PublicationShort descriptions of various research subjects taken up at the Department of Machine Design and Automotive Engineering are included in the paper. The subjects cover a wide range of bearing systems and tribology research and the research on tires and road surfaces. A third field of activity is biomedical engineering – with the attempts to improve methods of modelling biological materials in FEM calculations. The Department has...
-
THE EFFECT OF THE FRICTION OF THE REFUSE INSIDE THE REFUSE COLLECTION VEHICLE BODY ON THE WORKING PARAMETERS OF THE COMPACTION MECHANISM
PublicationMechanizm prasujący pojazdu do usuwania odpadów z pojemników (w skrócie PUOP) spełnia dwie funkcje. W pierwszym etapie zagęszcza zebrane z pojemników odpady, a następnie przemieszcza je w głąb skrzyni zbiorczej. Znajo-mość właściwości mechanicznych odpadów znajdujących się wewnątrz skrzyni może w znaczący sposób wpłynąć na poprawę wydajności pojazdu. Celem ba-dań było zwiększenie wydajności PUOP poprzez opracowanie w oparciu...
-
UKŁAD PRZENIESIENIA NAPĘDU TURBINY WIATROWEJ
PublicationIn a most commonly met design of a wind turbine the power is transmitted from the rotor to the generator through the system composed of the main shaft, friction connection, multiplicating gearbox and a flexible coupling. The driving system comprises almost a complete set of the machine elements being described during machine design lectures and can serve as an interesting illustration of the lectures.
Year 2014
-
Effect of the Presence of the Lifting Pocket on The THD Performance of a Large Tilting-Pad Thrust Bearing
PublicationIn this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of Itaipu power plant. B3earing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublicationHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublicationThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Special Issue on Sliding Contact Bearings
Publication
Year 2013
-
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems
Publication -
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems.
PublicationFluid–structure interaction technique seems to be one of the most promising possibilities for theoretical analysis of lubrication problems. It allows coupling of different physical fields in one computational task, taking into account the interaction between them. In this article, two sets of fluid–structure interaction analyses focusing on the bearing performance evaluation are presented. One analysis was applied to a water-lubricated...
-
CDIO IN GDANSK: PEOPLE-ORIENTED STRATEGY
PublicationThe CDIO system implementation in Poland meets problems and Gdansk University of Technology (GUT) is still a single higher education institution in Poland accepted as the member of CDIO Initiative. The paper detects and characterizes the existing problems to be solved. In particular, the different groups of people are considered as supporters or fighters against CDIO idea, their attitudes being considered and applied strategy demonstrated. The...
-
Effect of Coating Material Properties on Tilting-pad Thrust Bearing Performance
PublicationPolymer lined tilting-pad bearings demonstrate many advantages over traditional bearing systems. Bearings with a polymer layer in comparison with a babbitted layer show, for example: lower value of friction coefficient (important during start/stops), higher fatigue strength of the coating, better distribution of the load on individual pads due to lower elasticity of the polymers, wider range of operational temperatures or the ability...
-
Improving performance of large thrust bearings through modeling and experimentation
PublicationLarge thrust bearings are highly loaded machine elements and their failures cause serious losses. Start ups and stoppages of the bearing under load are specially critical regimes of operation. Load carrying capacity depends on the profile of the oil gap. In transient states this profile is also changing. In the design of large thrust bearings minimizing thermo-elastic deformations is an important goal, which can be accomplished...
-
Large Hydrodynamic Thrust Bearings and Their Application in Hydrogenerators
PublicationLarge hydrodynamic thrust bearings are the bearings which, due to hydrodynamic lubrication, allow large axial load to be transferred from a moving part (shaft) to the stationary part via a thin layer of the lubricant (usually oil), thus providing extremely low friction and practically no wear. Hydrogenerators with vertical shafts are the most important application of large thrust bearings. Main design and scientific problems of...
-
On the Possibilities of Decreasing Power Loss in Large Tilting Pad Thrust Bearings
PublicationJournal Menu About this Journal Abstracting and Indexing Aims and Scope Article Processing Charges Articles in Press Author Guidelines Bibliographic Information Citations to this Journal Contact Information Editorial Board Editorial Workflow Free eTOC Alerts Publication Ethics Submit a Manuscript Table of Contents Abstract Full-Text PDF Full-Text HTML...
-
Should we seek further improvement of fluid film bearings - what for and how?
PublicationFluid film bearings have been extensively used in the industry because of their unbeatable durability and extremely low friction coefficient. Large bearings supporting shafts of huge and important rotating machines constitute a special group of fluid film bearings since the reliability of crucial systems, like for example electro-energetic system, rely on their trouble-free operation. Large thrust bearings, apart from enormous...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublicationPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublicationThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
WSTĘPNA OCENA PRAWIDŁOWOŚCI DOBORU BARYŁKOWEGO ŁOŻYSKA PRZESIEWACZA I MOŻLIWYCH PRZYCZYN JEGO PRZYSPIESZONEGO ZUŻYCIA
PublicationW pracy przedstawiona analizę przyczyn awarii baryłkowych łożysk tocznych zainstalowanych w wibracyjnych sortownikach węgla. Podczas analizy poddano oględzinom uszkodzone łozysko i wykonano obbliczenia sprawdzające. Istotnym czynnikiem któy przyczynił się do powstania przedwczesnej awarii były zanieczyszczenia i stosowanie nieodpowiedniego gatunku smaru plastycznego.
Year 2012
-
Wielkogabarytowe hydrodynamiczne łożyska wzdłużne
PublicationW monografii przedstawiono problemy konstrukcyjne i badawcze hydrodynamicznych łożysk wzdłużnych o dużych średnicach. Łożyska takie stanowią istotne i niezwykle odpowiedzialne podzespoły hydrogeneratorów elektrowni wodnych. Z uwagi na rozmiary (średnice przekraczają niekiedy 5 metrów) i złożoność zjawisk łożyska te wymagają specjalnej postaci konstrukcyjnej, a ich dokładna analiza obliczeniowa przysparza wiele problemów. Dodatkowo...
Year 2011
-
Ocena stanu łożyska nośnego hydrozespołu HZ-2 EW żarnowiec i przyczyn jego awarii w dniach 31.05 i 16.06.2011
Publicationw pracy przedstawiono ocenę stanu łożyska nośnego hydrozespołu hz-2 EW Żarnowiec i przyczyn jego awarii w dniach 31.05 i 16.06.2011. Przeanalizowano przebieg obu awarii na podstawie zapisów z systemu diagnostycznego. Oceniono konstrukcję łożyska i przedstawiono ocenę przyczyn awarii oraz rekomendacje dotyczące usuwania przyczyn i skutków awarii
Year 2010
-
Badania teoretyczne i doświadczalne rozkładu temperatur w hydrodynamicznym łożysku wzdłużnym
PublicationW referacie zaprezentowano przykładowe wyniki obliczeń uzyskane z wykorzystaniem rozwijanej w Politechnice Gdańskiej nowej metody oceny własności hydrodynamicznych łożysk wzdłużnych. Bazuje ona na wykorzystaniu techniki automatycznej wymiany informacji pomiędzy uwzględnianymi w analizach problemów obliczeń łożyskowych obszarami zadania tj. płynowym i strukturalnym, wykorzystując w tym celu dostępne programy obliczeniowe MES (technika...
-
EXPERIMENTAL STUDY OF DIFFERENT SUPPLY DESIGNS IN HYDRODYNAMIC THRUST BEARINGS = Badania doświadczalne różnych sposobów smarowania wzdłużnych łożysk ślizgowych
PublicationHydrodynamiczne łożyska wzdłużne charakteryzują się znacznymi stratami tarcia, które przyczyniają się do wzrostu temperatury łożyska i obniżenia jego nośności. Obecnie olej smarujący jest zazwyczaj chłodzony w zewnętrznych układach chłodzenia. Po schłodzeniu olej jest dostarczany z powrotem do korpusu łożyska, z reguły do przestrzeni między klockami łożyska. Skuteczność dostarczania schłodzonego oleju w pobliże wlotu do szczeliny...
Year 2009
-
Obliczeniowa analiza wybranych systemów dostarczania smaru w hydrodynamicznych łożyskach wzdłużnych = Computational analysis of selected supply designs in hydrodynamic thrust bearings
PublicationPrzedstawiono przykładowe wyniki obliczeniowej analizy wpływu zastosowania wybranych systemów dostarczania schłodzonego oleju do łożyska na właściwości łożyska.
seen 4623 times