Search
prof. dr hab. inż. Tadeusz Stolarski
Publications
Filters
total: 18
Catalog Publications
Year 2018
-
Engineering Analysis with ANSYS Software Second Edition
PublicationThe best way to learn complex systems is by means of hands-on experience. With an innovative and clear tutorial based approach, this powerful book provides a comprehensive introduction to the fundamental areas of engineering analysis needed on research or commercial engineering projects. With its detailed step-by-step explanations and sample problems, this book will develop the reader's understanding of FEA and their ability to...
Year 2017
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublicationThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...
Year 2016
-
Acoustic journal bearing – Performance under various load and speed conditions speed conditions
PublicationThe paper presents results of experimental testing aiming at finding out what effect system of piezo-electric actuators (PZTs)attached to an aerodynamic journal bearing has on the magnitude of shaft's motion within the bearing operating at specified speed and load. The results clearly demonstrate effectiveness of PZTs in mitigating the shaft's motion thus contributing to the increased stability of the bearing. This stabilizing...
Year 2015
-
Acoustic journal bearing - A search for adequate configuration
PublicationClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
Peculiarities associated with testing polyetheretherketone (PEEK) in a model rolling contact
PublicationPolyetheretherketone (PEEK) was investigated using a modified version of the four-ball tester in which the upper forth ball was replaced by a cone in such a way that kinematics of the four-ball configuration were fully preserved. Rotation of the cone enforced orbiting and rolling of the ceramic balls around the polymer cup. The results produced some unexpected peculiarities in the wear of ceramic balls which, in principle, should...
-
Scientific research in the Department of Machine Design and Automotive Engineering
PublicationShort descriptions of various research subjects taken up at the Department of Machine Design and Automotive Engineering are included in the paper. The subjects cover a wide range of bearing systems and tribology research and the research on tires and road surfaces. A third field of activity is biomedical engineering – with the attempts to improve methods of modelling biological materials in FEM calculations. The Department has...
Year 2014
-
Some fundamental aspects of self-levitating sliding contact bearings and their practical implementations
PublicationIn this study, fundamental aspects and mechanisms of acoustic levitation together with governing equations are presented first. Then, the acoustic levitation phenomenon is considered as a new way to design air suspension systems capable of self-levitation. A particular emphasis is laid on journal bearings and their specific geometrical configuration. A practical feasibility of using acoustic levitation to separate contacting surfaces...
Year 2013
-
Experimental and analytical thermal study of PTFE composite sliding against high carbon steel as a function of the surface roughness, sliding velocity and applied load
PublicationThis study investigates the contact temperatures caused by frictional heating of sliding parallel pairs. In this case the materials studied are a PTFE composite in contact with a high carbon steel plate. These materials are commonly used for industrial applications, in particular as the main contacting components within a scroll expander system. The expected contact temperature values are important to be quantified in order to...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublicationThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
Running performance of an aerodynamic journal bearing with squeeze film effect
PublicationResults of theoretical and experimental studies concerning the performance of an aerodynamic journal bearing of which running is assisted by squeeze film ultrasonic levitation (SFUL) are presented in this paper. The SFUL mechanism not only can separate journal from the bearing at the start and stop phases of operation but also can significantly contribute to the dynamic stability of the bearing when it runs at speed. Computer calculations...
Year 2012
-
Performance of lubricated sliding contact in magnetic field
PublicationResults of experimental studies concerning theinfluence of permanent magnetic field on wear of lubricatedsliding contact operating at short stroke and highfrequency are presented. It was found that horizontalmagnetic is affecting performance of the contact. Thejagged delamination regions produced in the presence of amagnetic field can be regarded as easily undergoing oxidisationbecause oxygen is readily adsorbed there. Magneticfield...
-
Tribological performance of PTFE-metal binary coatings in rolling/sliding contact
PublicationTribological performance of surface coatings with embedded PTFE reservoirs in rolling/sliding contact is reported. Using two different coating materials and two shapes and patterns of PTFE reservoirs test samples in the form of discs were prepared and tested in a four-ball contact configuration under loads corresponding to nominal contact pressure of 0.5 and 1.0 GPa. It was found that one coating, namely aluminium-bronze with embedded...
Year 2011
-
Air journal bearing utilizing near-field acoustic levitation: stationary shaft case
PublicationResults of a study to examine a unique idea of self-levitating journal bearing are presented in this paper. the idea represents a radical departure from the current bearing technology. it utilisesacoustic levitation, which relies on the sound energy radiated by an object supporting a load. acoustic levitation has been demonstrated to support loads of up to 10 kg. in order to support a load theacoustic wave emitted by the radiating...
-
Influence of magnetic field on wear in high frequency reciprocatingsliding contacts
PublicationResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact operating at short stroke and high frequency are presented. It was found that horizontal magnetic field with different orientations relative to the sliding direction is affecting performance of the contact. The increase in frequency of sliding reduces accumulated mass loss and lowers the surface roughness of the wear...
-
Influence of permanent magnetic field on wear performance of dry sliding contacts
PublicationResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact are presented.It was found that magnetic field of horizontal orientation is causing temporary reduction of material's hardness. It also facilitates and accelerates removal process of wear particles from the contact zone.Formation of bulges, consisting of accumulated and compacted anti-ferromagnetic material produced...
-
Morphology of damage inflicted on brittle polymer in lubricated contact under cyclic static load
PublicationIn this article morphology of damage inflicted on the polymethylmethacrylate (PMMA) plate in static point lubricated contact with a ball made of five different materials under cyclic normal load has been presented. It is argued that the counterface material and lubricating film play an important role in the damage process and the extent of damage inflicted in the PMMA plate.
-
Running characteristics of aerodynamic bearing with self-lifting capability at low rotational speed
PublicationAn aerodynamic journal bearing that is capable of self-generating squeeze-film pressure is presented and its dynamic characteristics investigated numerically and experimentally. A numerical method based on a time marching static model was applied to assess the orbit trajectory path of the rotor upon a perturbation. Experimental results were obtained to validate the effect of the self- generated squeeze-film pressure on the stability...
Year 2010
-
Numerical modelling and experimental verification of compressible squeeze film pressure
PublicationThe validity of using the Reynolds equation for compressible squeeze film pressure was tested with computational fluid dynamics (CFD). A squeeze film air bearing was instrumented with pressure sensors and non-contacting displacement probes to provide transient measurements of film thickness and pressure. The film thickness measurements also provided input parameters to the numerical prediction. However, numerical results showed...
seen 2050 times