Publications
Filters
total: 334
Catalog Publications
Year 2020
-
Microstructure–Property Relationship of Polyurethane Foams Modified with Baltic Sea Biomass: Microcomputed Tomography vs. Scanning Electron Microscopy
PublicationIn this paper, novel rigid polyurethane foams modified with Baltic Sea biomass were compared with traditional petro-based polyurethane foam as reference sample. A special attention was focused on complex studies of microstructure, which was visualized and measured in 3D with high-resolution microcomputed tomography (microCT) and, as commonly applied for this purpose, scanning electron microscopy (SEM). The impact of pore volume,...
-
Performance of isotropic constitutive laws in simulating failure mechanisms in scaled RC beams
PublicationResults of numerical calculations of reinforced concrete (RC) beams are presented. Based on experimental results on longitudinally reinforced specimens of different sizes and shapes are investigated. Four different continuum constitutive laws with isotropic softening are used: one defined within continuum damage mechanics, an elasto-plastic with the Rankine criterion in tension and the Drucker-Prager criterion in compression, a...
-
Posadzki antyelektrostatyczne kluczowym elementem ochrony przed elektrycznością statyczną - wybrane wymagania techniczne
PublicationW artykule przedstwiono w spsoób syntetyczny zbiór podstawowych wymagań technicznych jakim powinny odpowiadać posadzki antyelektrostatyczne
-
Shear Cap Size Selection Method Based on Parametric Analysis of ACI-318 Code and Eurocode 2 Standard
PublicationThe scope of the paper is to propose a method for determining the size of shear caps in a slab–column-connections-reinforced concrete structure. Usually, shear heads are used to enhance slab–column connection, especially when the transverse reinforcement does not give the required punching shear load capacity. The dimensions of the shear head should provide the punching shear resistance of the connection inside and outside the...
-
Shear resistance of low height precast concrete lintels
PublicationThe scope of the paper is to investigate analytically and determine experimentally the shear resistance of low height reinforced precast concrete lintels. The chosen procedures included in national and international standards applied for the design of structural concrete elements to an estimation of shear behaviour of reinforced concrete elements are described. The characteristic and designed shear strength of precast concrete...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublicationThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
The Selection of Anchoring System for Floating Houses by Means of AHP Method
PublicationThis paper indicates and analyses the use of anchoring systems, such as mooring piles, booms, mooring cables, and deadweight anchors with additional elastic connectors, which are the most frequently applied by the producers of floating houses. The selection of the most advantageous anchoring system is complicated and requires the application of quantitative and qualitative data and methods. This publication presents the results...
-
Tynki - wykonywanie i pielęgnacja
PublicationW artykule przedstawiono podstawowe wymagania jakie powinny być zachowane podczas realizacji oraz późniejszej eksploatacji tynków tak aby jak najdłużej zachowac je w stanie wysokiej sprawności technicznej
-
Uwarunkowania użytkowania podłóg przemysłowych - Błędy projektowe
PublicationCelem artykułu jest wskazanie błędów popełnianych najczęściej przy projektowaniu podłóg przemysłowych. Opisane błędy mają wpływ na powstanie usterek i uszkodzeń zarówno przed, jak i w okresie ich eksploatacji.
-
Uwarunkowania użytkowania podłóg przemysłowych . Błędy wykonawcze
PublicationCelem artykułu jest wskazanie błędów najczęściej popełnianych w trakcie realizacji podłóg przemysłowych. Podobnie jak błędy projektowe maja one wpływ na powstawanie usterek i uszkodzeń zarówno przed, jak również w okresie eksploatacji podłóg przemysłowych. Artykuł ma charakter studium przypadku i został ograniczony do wybranej sytuacji z praktyki inżynierskiej
-
Wpływ błędów projektowych, wykonawczych oraz sposobu eksploatacji na trwałość podłóg przemysłowych
PublicationW artykule przedstawiono syntetyczna analizę przyczyn obniżonej trwałośc ibetonowych posadzek przemysłowych. Podano inżynierskie spsobu usuwania usterek i uszkodzeń będących następstwem niedociągnięć i błędów projektowych, wykonawczych, jak również niewłaściwego sposobu eksploatacji
-
Wpływ błędów projektowych, wykonawczych oraz sposobu eksploatacji na trwałość podłóg przemysłowych
PublicationCelem artykułu jest wskazanie najczęściej popełnianych błędów przy projektowaniu podłóg przemysłowych. Artykuł stanowi częśc 1 serii publikacji. Artykuł ma charakter studium przypadku i został ograniczony do wybranych przypadków z praktyki inżynierskiej
-
Wstępne badania eksperymentalne stalowych łączników balkonowych w aspekcie nośności złącza balkon - strop
PublicationW artykule przedstawiono analizę oraz wyniki wstępnych badań eksperymentalnych prefabrykowanych zestawów balkonowych w naturalnej skali o wymiarach (szerokość × długość × wysokość): 2,0 m × 2,78 m × 0,186 m (w spadku do 0,17 m) składających się z żelbetowych płyt połączonych ze sobą za pomocą stalowych łączników balkonowych w dwóch różnych typach rozwiązania. Ponadto artykuł zawiera przegląd literatury oraz przykładowych rozwiązań...
-
Wybrane zagadnienia projektowania, wykonawstwa oraz użytkowania betonowych posadzek przemysłowych w aspekcie ich ścieralności
Publicationw artykule przedstawiono najczęściej spotykane problemy związane z projektowaniem, realizacją oraz późniejszą eksploatacją posadzek w aspekcie ich ścieralności
-
Zakres stosowania tynków
PublicationW artykule podano podział tynków zwykłych ze względu na technikę wykonania, zalecane własności zapraw tynkarskich dla różnych tynków oraz klasyfikacjęwłaściwości suchych mieszanek tynkarskich
Year 2019
-
Analiza porównawcza metod obliczania przebicia
PublicationW artykule przedstawiono analizę porównawczą wybranych normowych metod wyznaczania nośności na przebicie konstrukcji płytowo-słupowej. Przeanalizowano trzy normowe sposoby wyznaczania nośności na przebicie.Wykonane obliczenia pozwoliły na wskazanie różnic w wyznaczonych wartościach nośności płyty na przebicie w konstrukcji płytowo-słupowej.
-
Application of multi-criteria method to assess the usefulness of a hydrotechnical object for floating housing
PublicationThis publication presents the analysis of three hydrotechnical objects located in the Municipality of Gdańsk with a view of mooring Floating Houses. The assessment of the adaptation of a hydrotechnical object has been carried out by a multi- criteria method AHP and using the main criteria such as: mooring system, communication with the mainland, availability of the utility networks, waste disposal and location of the parking spaces....
-
Assessment of Failure Occurrence Rate for Concrete Machine Foundations Used in Gas and Oil Industry by Machine Learning
PublicationConcrete machine foundations are structures that transfer loads from machines in operation to the ground. The design of such foundations requires a careful analysis of the static and dynamic effects caused by machine exploitation. There are also other substantial differences between ordinary concrete foundations and machine foundations, of which the main one is that machine foundations are separated from the building structure....
-
Assessment of technical condition and repair of steel structure elements on the example of fire damage in a warehouse building
PublicationThe paper analyses a case study on the structural assessment of warehouse building partially damaged by fire caused by external source (fire of lorries close to the building). The authors focus on the site investigations and laboratory test results prior to assessing actual condition of the structural elements. Both strengthening concept and repair procedure of a steel column are addressed here. A short literature survey in the...
-
Badania diagnostyczne posadzki w Bazylice św. Mikołaja w Gdańsku
PublicationZmiany warunków otoczenia obiektów zabytkowych, do których można zaliczyć industrializację otoczenia, ruch pojazdów mechanicznych, zanieczyszczenie środowiska oraz okresowe zmiany poziomu wód gruntowych, mają niejednokrotnie negatywny wpływ na ich stan techniczny. W przypadku pojawienia się pierwszych oznak uszkodzeń elementów konstrukcyjnych lub wykończeniowych, ocena wpływu poszczególnych czynników jest utrudniona, w szczególności,...