ISSN:
eISSN:
Disciplines
(Field of Science):
- biomedical engineering (Engineering and Technology)
- civil engineering, geodesy and transport (Engineering and Technology)
- materials engineering (Engineering and Technology)
- mechanical engineering (Engineering and Technology)
- chemical sciences (Natural sciences)
(Field of Science)
Ministry points: Help
Year | Points | List |
---|---|---|
Year 2024 | 200 | Ministry scored journals list 2024 |
Year | Points | List |
---|---|---|
2024 | 200 | Ministry scored journals list 2024 |
2023 | 200 | Ministry Scored Journals List |
2022 | 200 | Ministry Scored Journals List 2019-2022 |
2021 | 200 | Ministry Scored Journals List 2019-2022 |
2020 | 200 | Ministry Scored Journals List 2019-2022 |
2019 | 200 | Ministry Scored Journals List 2019-2022 |
2018 | 35 | A |
2017 | 35 | A |
2016 | 35 | A |
2015 | 35 | A |
2014 | 35 | A |
2013 | 35 | A |
2012 | 40 | A |
2011 | 40 | A |
2010 | 32 | A |
Model:
Points CiteScore:
Year | Points |
---|---|
Year 2022 | 10.4 |
Year | Points |
---|---|
2022 | 10.4 |
2021 | 9.3 |
2020 | 8 |
2019 | 7.9 |
2018 | 6.4 |
2017 | 5.1 |
2016 | 4.4 |
2015 | 4.2 |
2014 | 4.2 |
2013 | 3.7 |
2012 | 3.5 |
2011 | 2.8 |
Impact Factor:
Sherpa Romeo:
Papers published in journal
Filters
total: 26
Catalog Journals
Year 2015
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublicationWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
Year 2013
-
Theoretical study of thermofrictional oscillations due to negative friction-temperature characteristic
PublicationAnalytical study on oscillations of a body on a moving counterbody has been done by assuming imperfect frictional thermal contact and friction that decreases with contact temperature. It has been shown that stick-slip oscillation occurs due to decrease of friction coefficient when the body moves in the opposite direction to the counterbody. Dynamical characteristics, such as conditions for stable sliding and limit cycles, have...
Year 2011
-
Influence of magnetic field on wear in high frequency reciprocatingsliding contacts
PublicationResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact operating at short stroke and high frequency are presented. It was found that horizontal magnetic field with different orientations relative to the sliding direction is affecting performance of the contact. The increase in frequency of sliding reduces accumulated mass loss and lowers the surface roughness of the wear...
Year 2010
-
Numerical modelling and experimental verification of compressible squeeze film pressure
PublicationThe validity of using the Reynolds equation for compressible squeeze film pressure was tested with computational fluid dynamics (CFD). A squeeze film air bearing was instrumented with pressure sensors and non-contacting displacement probes to provide transient measurements of film thickness and pressure. The film thickness measurements also provided input parameters to the numerical prediction. However, numerical results showed...
Year 2008
-
Modeling lubricant flow between thrust-bearing pads
PublicationInlet temperature is one of the main inputs in all models for the analysis of fluid film bearing performance. At the same time, inlettemperature distribution and also oil velocity distribution at the inlet are the result of flow phenomena in the gap between the bearingpads. These phenomena are complex and in many cases further affected by any special arrangements of forced oil supply to the gapbetween pads. The reason for such...
-
The influence oil additives on spread cracks in silicon nitride
PublicationThe paper presents an experimental study of the influence of oil additives (Cl, S, P, cerium dioxide (CeO2)) on spread cracks in silicon nitride. The additives Cl, S, P are bound in molecules in liquid form soluble in the base oil. The CeO2 is purely in powder form in suspension. The use of CeO2 powder was made based on the good results of polishing of silicon nitride. A ceramic angular contact ball bearing was modelled using a...
seen 1534 times