Search
ISSN:
eISSN:
Ministry points: Help
| Year | Points | List |
|---|---|---|
| Year 2025 | 5 | Journal not listed on ministry scored journal list 2024 |
| Year | Points | List |
|---|---|---|
| 2025 | 5 | Journal not listed on ministry scored journal list 2024 |
| 2024 | 5 | Journal not listed on ministry scored journal list 2024 |
| 2023 | 5 | Not listed on the ministry scored journals list 2023 |
| 2022 | 5 | Not listed on the ministry scored journals list (2019-2022) |
| 2021 | 5 | Not listed on the ministry scored journals list (2019-2022) |
| 2020 | 5 | Not listed on the ministry scored journals list (2019-2022) |
| 2019 | 5 | Not listed on the ministry scored journals list (2019-2022) |
| 2018 | 1 | Journals not listed on the ministry scored lists 2017-2018 |
| 2017 | 1 | Journals not listed on the ministry scored lists 2017-2018 |
| 2016 | 5 | foreign scientific journals |
| 2015 | 5 | foreign scientific journals |
| 2014 | 5 | foreign scientific journals |
| 2013 | 5 | foreign scientific journals |
| 2012 | 5 | foreign scientific journals |
Impact Factor:
Papers published in journal
Filters
total: 12
Catalog Journals
Year 2024
-
CUPPING DEFORMATION DURING DRYING OF BEECH WOOD (FAGUS SYLVATICA L.)
PublicationWood drying does not only consist in removing its moisture: the quality of the dried product is the main requirement for the industrial process. Because wood shrinks during drying, deformations and stresses develops than can lead to unusable product. When developing drying technologies and methods, the aim is to achieve the shortest possible drying times. The most common defects in wood after drying include cross warping (cup),...
Year 2022
-
EFFECT OF PRESS DRYING ON DIMENSION STABILITY AND DENSITY OF BEECH WOOD,
PublicationTimber is traditionally dried in kilns by processes that often take several days or weeks to complete. At present, it is possible to apply several methods of rapid drying of timber, including, for example, press drying. This research is based on the use of this process. Drying was performed using the heating plates with a temperature of 160 °C. Three pressures were compared in the research 1.0 MPa, 1.4 MPa, and 1.8 MPa. The density...
-
OVERALL SET OF BANDSAW TEETH VERSUS METHODS OF MEASUREMENTS
PublicationThis article deals with the impact of the manual methods of measurement on the overall set measurement results. It describes the results of the measurement of bandsaw teeth kerf with the use of a micrometer and a digital calliper. It is commonly known that the cutting process causes the wear of cutting tools. The wear of the cutting edge depends on the cutting conditions as well as on the mechanical properties of the processed...
-
Preliminary studies on the effect of feed speed on the colour change of wood
PublicationThis paper presents the results of preliminary analyses of the effect of cutting parameters on changes in the colour of wood. Beech wood cut with use circular saw was analysed. The cutting parameter tested was the feed speed, represented by the feed per tooth. Sawing processes with different feed per tooth ranging from 0.0008 mm to 0.09 mm were analysed. It was observed that over the entire range of feed rate per tooth analysed,...
Year 2020
-
THE EFFECT OF DRYING INTENSITY ON THE COLOR CHANGES OF PINE WOOD (PINUS SYLVESTRIS L.)
PublicationThe effect of the selection of drying process parameters on the color change of Scots pine wood (Pinus Sylvestris L.) is presented. In this work the experimental studies have been performed. The research focused on the influence of drying intensity on the changes of color after drying process. Intensity of drying process was determined on the basis of the average drying gradient. To determine the color of wood before and after...
Year 2018
-
Numerical analysis of chip removing system operation in circular sawing machine using CFD software
PublicationPaper presents the analysis of the results of numerical simulations of the air flow process of wood chips removing system in the circular sawing machine. The attention is focused on the upper cover and bottom shelter of the chip removing system. Within the framework of the work a systematic numerical modeling of the air flow distribution in the cover and shelter during operation of the selected rotational speed of saw blade with...
-
The effect of full-cell impregnation of pine wood (Pinus Sylvestris L.) on the fine dust content during sawing on a frame sawing machine
PublicationIn this paper the results of the analysis of the effect of the impregnation treatment of pine wood on the granularity of sawdust from the sawing process on the frame sawing machine PRW 15M are presented. Granulometric analyses of chips from impregnated and unimpregnated pine wood implies that the impregnation of pine wood does not affect the size and structure of the sawdust produced. A major ≈ 95% share of the formed chips is...
Year 2016
-
EMPIRICAL ASSESMENT OF THE MAIN DRIVING SYSTEM OF THE CIRCULAR SAWING MACHINE
PublicationThe producers of panel saws tend to improve sawing accuracy and minimise a level of vibrations, to increase their competitiveness at the market. Mechanical vibrations in the main saw driving system, which level depend on a plethora independent factors, may really affect sawing accuracy and general machine tool vibrations. The objective of the research was to explore vibrations signals of the main spindle system, and to extract...
-
Experimental analysis of chip removing system in circular sawing machine
PublicationPaper presents analysis of the process of removing the wood chips generated during the cutting of the material on the circular sawing machine. The attention is focused on the upper cover of the chip removing system. Within the framework of the work a systematic experimental study of pressure distribution in the cover during operation of the selected rotational speed of saw blade with a diameter of 300 mm and 450 mm was carried...
-
High temperature drying of beech with content of tension wood
PublicationThe presented artcle is focused on comparison of tension and normal wood of beech (Fagus sylvatica L.) in a high-temperature drying process. Samples of 26 mm thickness were selected from sapwood zone with different angle of growth rings. The article evaluated properties of tension and normal wood before and after drying process. Properties which are monitored were moisture, moisture gradients, covering tests, colour changes and...
-
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublicationIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
THE USE OF FEM FOR DETERMINATION OF RESONANT FREQUENCIES OF CIRCULAR SAW BLADES WITH INDIRECT TEETH IN GULLETS
PublicationUnderstanding the dynamical properties of the circular saw blade is necessary, since, there is a really need for a stable work at working rotational speeds, which are determined by frequencies at which the circular saw blade tends to vibrate. It was observed that the resonant frequency depend on the circular saw blade shape, a collar diameter and on saw’s teeth shape. In the presented work an attention was paid to the effect of...
seen 861 times