dr hab. inż. Artur Olszewski
Zatrudnienie
- Profesor uczelni w Instytut Mechaniki i Konstrukcji Maszyn
Publikacje
Filtry
wszystkich: 95
Katalog Publikacji
Rok 2023
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublikacjaThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
The influence of polymer bearing material and lubricating grooves layout on wear of journal bearings lubricated with contaminated water
PublikacjaThe goal of the present paper is to investigate wear properties of journal sliding bearing operating in the conditions of contaminated water lubrication. Several bearing materials and bearing sleeve designs (differing in the axial grooves position and their shape) were tested experimentally under typical operating conditions in a dedicated test rig, which was equipped with a lubricating system, enabling lubrication with contaminated...
-
Theoretical analysis and experimental tests of tilting pad journal bearings with shoes made of polymer material and low-boiling liquid lubrication
PublikacjaSelecting the appropriate bearing system for the rotor requires a good knowledge of the available solutions and the operating conditions of the machine. For newly designed machinery operating in adverse conditions, selecting bearings that ensure correct and long-lasting operation can be extremely challenging. Difficulties in- crease when the machine’s operating parameters are beyond the technical capabilities of available technical solutions....
Rok 2022
-
Comparison of the characteristics of journal bearings determined according to ISO 7902:2020 and obtained by other methods
PublikacjaThe article presents selected characteristics of journal bearings calculated with the use of various methods and compared to the results obtained with application of the basic bearing characteristics calculation procedure, as described in the ISO 7902:2020 standard. Additionally, the presented calculation results were compared with the parameters measured during experimental tests of the sliding bearings, working under loads and...
Rok 2020
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublikacjaThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
Rok 2019
-
Experimental investigation into surface texture effect on journal bearings performance
PublikacjaThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
THEORETICAL AND EXPERIMENTAL INVESTIGATION OF THIN-WALLED BEARING SHELL’S DESIGN PARAMETERS AND ASSEMBLY CONDITIONS ON THE HOLDING TORQUE INSIDE A HOUSING BORE OF A CONNECTING ROD
PublikacjaThe aim of the work was the experimental and theoretical evaluation of the influence of the most important parameters determining the holding torque of a thin-walled bearing shell inside a housing bore of a connecting rod. The main investigated parameters were defned by authors experience in this feld. In the frst stage of research, a special test stand was designed in order to allow measuring the real values of the friction torque...
Rok 2018
-
Analiza wytrzymałościowa zmodyfikowanej belki liny łyżkowej zainstalowanej na platformie Lotos Petrobaltic
PublikacjaPrzedmiotem sprawozdania jest analiza wytrzymałosciowa zmodyfikowanej belki liny łyżkowej zainstalowanej na platformie Lotos Petrobaltic. Modyfikacja polega na wykonaniu w belce przelotowego otworu umozliwiającego zamontowanie czujnika napięcia liny łyżkowej.
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublikacjaAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
ANALYSIS OF THE LOAD-CARRYING CAPACITY OF A HYDRODYNAMIC WATER-LUBRICATED BEARING IN A HYDROELECTRIC POwER PLANT
PublikacjaThe paper presents an analysis of the load-carrying capacity of a historic hydrodynamic water-lubricated radial bearing of an unconventional segment design installed in the Braniewo Hydroelectric Power Plant. The aim of the calculations was to determine whether the bearing operates in the conditions of hydrodynamic or mixed lubrication, as well as to establish the optimal geometry of the axial grooves allowing for the highest load-carrying...
-
Ecological bearing systems for water turbines – research and development at Gdansk University of Technology
PublikacjaIncreasing requirements for environmental protection make it necessary to introduce new materials and designs. Hydroelectric power plants operating in direct contact with water reservoirs and rivers are potentially endangering water cleanliness, hence they should also be modernized in the way minimizing the environmental hazards. A lot of progress in this field has been achieved in last decades, but still there is much work to...
-
Evaluation of bearing and journal damage in MAN 9L40-54 engines installed on M/V STENA SCANDINAVICA ferry
PublikacjaThe following report was requested by Remontowa Shiprepair Yard (RSY) S.A. in Gdansk ´ (contract no. 4/2018/EX/U, dated 13.02.2018) and prepared based on the materials received from RSY, two on-board inspections and the participation of the contractors in three conferences with RSY representativesi. The goal of the analysis performed by the experts of Gdansk University of Technology was ´ to determine the character of the bearing...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublikacjaThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
FEM Calculations in Analysis of Steel Subsea Water Injection Flowlines Designing Process
PublikacjaPaper describes the result of theoretical research aimed at assessing the loads and operating conditions of a Coiled Tubing pipeline injecting water, suspended to the mining platform of Lotos Petrobaltic. For this purpose, appropriate calculation models have been developed using the Finite Element Method (FEM), taking into account the nature of the analyzed object and its loads. The analyzes were carried out for two pipes (previously...
-
OPINIA TECHNICZNA nr 3/PG/mosty Sprawowanie nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską” Opinia nt. rozwiązań technicznych przedstawionych w projekcie budowlanym przekopu w lokalizacji Nowy Świat - branża mostowa
PublikacjaOpinię przygotowano w ramach prowadzonego nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską”.
-
OPINIA TECHNICZNA nr 5/PG/mosty Sprawowanie nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską” Opinia nt. rozwiązań technicznych przedstawionych w projekcie wykonawczym przekopu w lokalizacji Nowy Świat - branża mostowa
PublikacjaOpinię przygotowano w ramach prowadzonego nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską”.
-
OPINIA TECHNICZNA nr 8/PG/mosty Sprawowanie nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską” Opinia uzupełniająca do 5/PG/mosty w zakresie mechanizmów zastosowanych na przekopie po przedstawieniu przez projektanta wyciągu z obliczeń
PublikacjaOpinię przygotowano w ramach prowadzonego nadzoru naukowo-technicznego podczas opracowywania projektów obiektów hydrotechnicznych, mostowych i drogowych w ramach realizacji przedsięwzięcia pn. „Budowa drogi wodnej łączącej Zalew Wiślany z Zatoka Gdańską”.
-
Results from tests on bolted connection components for evaluation of friction coefficient in various contact conditions
PublikacjaThe main purpose of the work was the analysis and evaluation of the self-locking quality of a bolted joint covered with Xylan 1070 coating, with comparison to the classic bolts lubricated with Molykote compound during assembly. The second part of the work was the verification of the compliance of the bolts and nuts used in the installation with the ASME B1.1 norm.
Rok 2016
-
OPERATING CONDITIONS OF SLIDE BEARINGS OF MILLS USED IN KGHM POLSKA MIEDŹ S.A.
PublikacjaThe paper contains the results from a tec hnical analysis of the conditions of the operation of hydrodynamic bearings supporting the drums of ore processing mills at KGHM Polska Mied ź S.A. A theoretical analysis was performed on the grounds of onsite examination and measurem ents of principal dimensions of the bearings of interest. The computer simulation covered the characteristics of the oil film in the bearings...
Rok 2015
-
ANALIZA I MODERNIZACJA ŁOŻYSKA NR 1 TURBOZESPOŁU TG3 EC BYDGOSZCZ
PublikacjaCelem pracy było wykonanie analizy warunków pracy łożyska nr 1 turbozespołu TG3 zainstalowanego w EC Bydgoszcz oraz opracowanie projektu nowego łożyska o korzystniejszych własnościach dynamicznych w celu uzyskania stabilniejszej pracy turbozespołu w całym zakresie mocy.
wyświetlono 1818 razy