Wyszukiwarka
dr inż. Jakub Konkol
Zatrudnienie
- Adiunkt w Katedra Geotechniki i Inżynierii Wodnej
Publikacje
Filtry
wszystkich: 27
Katalog Publikacji
Rok 2024
-
Bearing capacity of monotonically installed tapered piles in medium dense Fontainebleau sand
PublikacjaA series of installation of tapered piles in medium-dense Fontainebleau sand were performed in the geotechnical centrifuge at Gustave Eiffel University. The models of piles with three different shapes - straight profile (S), and with taper angle of 0.70 degrees (T1), and 1.4 degrees (T2) were used. The piles were instrumented with fiber optic wires on the shaft and load cell at the base. After monotonic installation, the models were...
Rok 2023
-
Incorporating installation effects into the probability analysis of controlled modulus columns
PublikacjaThis technical report presents the probabilistic analysis which integrates the Monte Carlo simulation (MCS) with random field theory to model the load–displacement behavior of Controlled Modulus Columns (CMCs) in overconsolidated Poznań clay. Presented study focuses on the practical aspects of statistical analysis of geotechnical data, numerical model development, and results evaluation. Variability and spatial distribution of...
-
Influence of Soft Soil Samples Quality on the Compressibility and Undrained Shear Strength – Seven Lessons Learned From the Vistula Marshlands
PublikacjaThis technical article presents the influence of sample quality on the compressibility parameters and undrained shear strength ( c u ) of soft soils from the Vistula Marshlands. The analysis covers: (1) quality of soft soil according to three criteria: void ratio (Δ e / e 0 index), volumetric strain (Δ ɛ v ) and C r / C c ratio; (2) influence of storage time on quality; (3) influence of sample quality on undrained shear strength...
Rok 2022
-
Discussion of “Stress-Displacement Response of Sand–Geosynthetic Interfaces under Different Volume Change Boundary Conditions” by Aliyeh Afzali-Nejad, Ali Lashkari, and Alejandro Martinez
PublikacjaThe influence of normal stiffness of interface on the interpretation of shear box tests
Rok 2021
-
Pore Water Pressure Development in Soft Soil due to Installation and Loading of Controlled Modulus Columns
PublikacjaExcess pore water pressure (EPWP) development and decay due to the installation and static loading tests of controlled modulus columns (CMC) in soft soil was measured with piezometers equipped with low air entry (LAE) filters and a piezocone (CPTU) equipped with a high air entry (HAE) filter. The HAE filter allows for detailed detection of EPWP in short time intervals during construction of CMC. The influence zone due to the installation...
-
Shaft friction from the DMT and direct shear interface tests
PublikacjaThe article presents preliminary attempt to create tri-linear transfer curves for describing pile behaviour under axial loading. Transfer curves would use the parameter measured in dilatometer test, particularly a constrained modulus MDMT. The proposed method is based on concrete rough and smooth interface tests performed in a direct shear apparatus. Based on the obtained mobilization curves, relationships were created between...
-
Some Aspects of Shear Behavior of Soft Soil–Concrete Interfaces and Its Consequences in Pile Shaft Friction Modeling
PublikacjaThis paper examines the stiffness degradation and interface failure load on soft soil–concrete interface. The friction behavior and its variability is investigated. The direct shear tests under constant normal load were used to establish parameters to hyperbolic interface model which provided a good approximation of the data from instrumented piles. Four instrumented piles were used to obtain reference soil–concrete interface behavior....
-
Statistical evaluation of physical and index properties of Vistula Marshlands deltaic soft soils
PublikacjaThis paper provides statistical evaluation of physical and index parameters of the Vistula Marshlands deltaic soft soils using three datasets. Soft soils from the Vistula Marshlands are grouped into the four categories: (1) silty/sandy loams, (2) organic clays, (3) organic silts and (4) peats. Variability of basic and derivative physical properties as well as Atterberg's limits and plasticity index is studied. It is found that...
Rok 2020
-
Discussion of “Axisymmetric Simulations of Cone Penetration in Saturated Clay” by Diane M. Moug, Ross W. Boulanger, Jason T. DeJong, and Robert A. Jaeger
PublikacjaN/A
-
Discussion:Horizontal stress increase induced by deep vibratory compaction
PublikacjaDeep compaction control of granular material using the results of field tests. The analysis include the CPTU and DMT tests terformed before and after compaction works.
Rok 2019
-
Application of the ‘CPT 2012’model of AFNOR standard for column design in Poland–Jazowa case study
Publikacjahis paper presents the ‘CPT 2012’ model incorporated into the AFNOR NF P94-262:2012-07, French standard for pile design fully compatible with Eurocode 7, to the wider Polish audience. The bearing capacity of three reference columns for Vistula Marshlands have been calculated according to ‘CPT 2012’ model and AFNOR recommendations. Then, the design resistances have been compared with ultimate column bearing capacity measured during...
-
Discussion on “Coupled effective stress analysis of insertion problems in geotechnics with the Particle Finite Element Method” by L. Monforte, M. Arroyo, J.M. Carbonell, and A. Gens
PublikacjaAddressed here is the Particle Finite Element Method (PFEM) modelling of undrained CPTu penetration with regard to a reference analytical solution based on the Spherical Cavity Expansion Method (SCEM). Also discussed is the choice of the soil model and its parameters. The effect of cone interface friction on CPTu simulation is analyzed in a series of penetration tests using Arbitrary Lagrangian-Eulerian (ALE) and Updated Lagrangian...
-
Effective Friction Angle Of Deltaic Soils In The Vistula Marshlands
PublikacjaThis article presents the results of laboratory tests on soft, normally consolidated soils from the Vistula Marshlands. Samples of high-plasticity organic soils (muds) taken from 3.2–4.0 m and 9.5–10.0 m depth, as well as peat deposit at 14.0 m, are analysed. Presented case study confirms the applicability of the Norwegian Institute of Technology (NTH) method based on Cone Penetration Tests (CPTU) and allows for a conservative...
-
Geotechnical characterization of soft soil deposits in Northern Poland
PublikacjaThis paper presents a geotechnical characterization of deltaic soft soil deposits in the Vistula Marshlands, northern Poland. It shows the limited applicability of organic soil classifications based on Cone Penetration Tests (CPTU) and Dilatometer Tests (DMT). None of the in-situ-based classifications correctly identifies peat. Analysis of the behaviour of contractive/dilative soil layers according to Robertson's updated classification...
-
LDFEM analysis of pore water pressure development in cohesive soil due to FDP auger drilling
PublikacjaThis paper presents the preliminary modelling of FDP auger drilling in soft soil with emphasis on excess pore water pressure (EPWP) development using CEL formulation and Abaqus software suit. The EPWP generation in single points is investigated and the results of a numerical analysis are compared with the field measurements. It is found that numerical model qualitatively reflects the field measurements. However,...
Rok 2018
-
Large deformation modelling of CPT probing in soft soil—pore water pressure analysis
PublikacjaThis paper presents the results of finite element modelling with Updated Lagrangian formulation of the Cone Penetration Test in soft soil deposit located in Jazowa, Poland. The numerical calculations are carried out for homogenous, normally consolidated, organic soil layer. The Modified Cam Clay constitutive model for soft soil and Coulomb model for interface are used. The study compares the registered pore water pressure distributions...
-
LDFEM analysis of FDP auger installation in cohesive soil
PublikacjaThis paper deals with large deformation finite element (LDFE) preliminary modelling of Full Displacement Pile (FDP) installation in cohesive soil deposit located in Jazowa, Poland. The detailed FDP auger geometry is applied and the drilling process is modelled with full 3D Coupled Eulerian-Lagrangian (CEL) formulation. The total stress approach and elastic-perfectly plastic model with rate-dependent Mises plasticity is used. The...
-
Numerical analysis of pile installation effects in cohesive soils
PublikacjaIn this thesis the empirical equation for radial effective stress calculation after displacement pile installation and following consolidation phase has been proposed. The equation is based on the numerical studies performed with Updated Lagrangian, Arbitrary Lagrangian-Eulerian and Coupled Eulerian-Lagrangian formulations as well as the calibration procedure with database containing world-wide 30 pile static loading tests in cohesive...
-
Strength parameters of deltaic soils determined with CPTU, DMT and FVT
PublikacjaThis paper presents the results of soil investigation in soft, normally consolidated organic soil in the estuary of Vistula river. The analysis concerns clayey mud and peat layers interbedded with loose to medium-dense sands. Several Cone Penetration Tests with pore water measurement (CPTU), Dilatometer Tests (DMT) and Field Vane Tests (FVT) were performed on the testing site. The cone factor Nkt was estimated using the results...
Rok 2017
-
Influence of Installation Effects on Pile Bearing Capacity in Cohesive Soils – Large Deformation Analysis Via Finite Element Method
PublikacjaIn this paper, the whole process of pile construction and performance during loading is modelled via large deformation finite element methods such as Coupled Eulerian Lagrangian (CEL) and Updated Lagrangian (UL). Numerical study consists of installation process, consolidation phase and following pile static load test (SLT). The Poznań site is chosen as the reference location for the numerical analysis, where series of pile SLTs...
-
Installation of CMC columns in overconsolidated clays
PublikacjaDuring rigid inclusions execution in the subsoil some monitoring data are registered by a drilling rig for quality control. The use of these data can improve the design procedure of soil improvement as they can provide some information about the position of bearing strata and the energy necessary to install the column in the ground. In this paper the parameters registered in a drilling machine are described, the installation...
-
Numerical Modeling of Cone Penetration Test in Slightly Overconsolidated Clay with Arbitrary Lagrangian-Eulerian Formulation
PublikacjaIn this paper the results of the cone penetration test (CPT) modeling with the arbitrary Lagrangian-Eulerian (ALE) formulation provided by Abaqus software package have been presented. The study compares the cone resistance and sleeve friction obtained in numerical analysis with values measured in soundings performed in the uniform layer of clayey soil in the Koszalin area. The clay layer was found to be slightly overconsolidated...
Rok 2016
-
Large deformation finite element analysis of undrained pile installation
PublikacjaIn this paper, a numerical undrained analysis of pile jacking into the subsoil using Abaqus software suit has been presented. Two different approaches, including traditional Finite Element Method (FEM) and Arbitrary Lagrangian–Eulerian (ALE) formulation, were tested. In the first method, the soil was modelled as a two-phase medium and effective stress analysis was performed. In the second one (ALE), a single-phase medium was assumed...
Rok 2015
-
Numerical estimation of the pile toe and shaft unit resistances during the installation process in sands
PublikacjaNumerical simulations of a pile jacking were carried out. A Coupled Eulerian–Lagrangian (CEL) formulation was used to treat with large deformation problems. An Abaqus, a commercial Finite Element Method software suit, was used as a computing environment. The Mohr–Coulomb constitutive model was applied and the Coulomb model of friction was used to describe pile-soil interaction. Calculations were made for three different pile diameters....
Rok 2014
-
Derivation of the scaling laws used in geotechnical centrifuge modelling-application of dimensional analysis and Buckingham Π theorem
PublikacjaGeotechnical centrifuge modelling has been a world-wide used technology in physical tests. In this paper a derivation of scaling laws by dimensional analysis for the centrifugal modelling is presented. Basic principles of centrifuge modelling are described. Scaling laws for slow events like consolidation and fast events like dynamic loads are shown. The differences in scale factors for both processes are noticed. The aim of this...
-
Numerical solutions for large deformation problems in geotechnical engineering
PublikacjaThe problem of large deformations often occurs in geotechnical engineering. Numerical modeling of such issues is usually complex and tricky. The chosen solution has to implicate soil-soil and soil-structure interactions. In this paper, a review of the most popular numerical methods for large deformation problems is presented. The Coupled Eulerian-Lagrangian (CEL) method, the Arbitrary Lagrangian-Eulerian (ALE) method, the Smoothed...
-
Wirówka geotechniczna - historia, modelowanie i współczynniki skali
PublikacjaRozwój modelowania zjawisk geotechnicznych w wirówce. Historia rozwoju urządzenia. Przyczyny wykorzystania wirówki geotechnicznej przez ośrodki naukowe i biura inżynieryjne. Obecny status urządzenia w edukacji i przemyśle. Podstawy teoretyczne badań modelowych w wirówce geotechnicznej. Lista wybranych zależności korelacyjnych. Przegląd i dyskusja wybranych współczynników skali.
wyświetlono 3637 razy