Microstructure and Mechanical Properties of Combined GTAW and SMAW Dissimilar Welded Joints between Inconel 718 and 304L Austenitic Stainless Steel - Publikacja - MOST Wiedzy

Twoje konto

zaloguj

Wyszukiwarka

Microstructure and Mechanical Properties of Combined GTAW and SMAW Dissimilar Welded Joints between Inconel 718 and 304L Austenitic Stainless Steel

Abstrakt

A dissimilar welded joint of Inconel 718 and 304L austenitic stainless steel was prepared using a combined procedure with the gas tungsten arc welding and shielded metal arc welding processes by employing the Ni-based fillers: ERNiCr-3 and ENiCrFe-3. The welded joints were investigated for metallographic testing and mechanical properties, and a relationship was established between the microstructure and the resultant mechanical properties. Microstructural observation revealed the formation of the unmixed zone on the 304L SS side. The weld metal showed that the fully austenitic microstructure consisted of the Nb- and Ti-rich carbide phases along the inter-dendritic spaces. The tensile test results at room temperature showed the failure from the weld metal which might be due to alloying element segregation along the inter-dendritic spaces. However, a tensile test at 600 ◦C showed the failure from the 304L SS base metal with a tensile strength and % elongation value of 377 MPa and 24%, respectively. The hardness plot showed the average hardness value of the weld metal of 236 ± 5 HV, which was higher than the 304L SS BM (204 ± 4 HV) but lower than the IN718 BM (243 ± 5 HV). The impact toughness of the weld metal was 109 J, which was significantly lower than the base metals. The poor impact strength of the weld metal might be due to the evolution of the NbC phase along inter-dendritic spaces

Cytowania

  • 2 2

    CrossRef

  • 0

    Web of Science

  • 2 1

    Scopus

Autorzy (8)

Cytuj jako

Pełna treść

pobierz publikację
pobrano 4 razy
Wersja publikacji
Accepted albo Published Version
DOI:
Cyfrowy identyfikator dokumentu elektronicznego (otwiera się w nowej karcie) 10.3390/met13010014
Licencja
Creative Commons: CC-BY otwiera się w nowej karcie

Słowa kluczowe

Informacje szczegółowe

Kategoria:
Publikacja w czasopiśmie
Typ:
artykuły w czasopismach
Opublikowano w:
Metals nr 13,
ISSN: 2075-4701
Język:
angielski
Rok wydania:
2023
Opis bibliograficzny:
Sirohi S., Pandey S. M., Świerczyńska A., Rogalski G., Kumar N., Landowski M., Fydrych D., Pandey C.: Microstructure and Mechanical Properties of Combined GTAW and SMAW Dissimilar Welded Joints between Inconel 718 and 304L Austenitic Stainless Steel// Metals -Vol. 13,iss. 1 (2023), s.14-
DOI:
Cyfrowy identyfikator dokumentu elektronicznego (otwiera się w nowej karcie) 10.3390/met13010014
Źródła finansowania:
  • COST_FREE
Weryfikacja:
Politechnika Gdańska

wyświetlono 56 razy

Publikacje, które mogą cię zainteresować

Study on Microstructure-Property Relationship of Inconel 617 Alloy/304L SS Steel Dissimilar Welds Joint

  • A. Kumar,
  • K. Guguloth,
  • S. M. Pandey
  • + 3 autorów
2023

Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study

  • S. Sirohi,
  • N. Kumar,
  • A. Kumar
  • + 4 autorów
2023

Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel Alloy

2020

Dissimilar autogenous TIG joint of Alloy 617 and AISI 304H steel for AUSC application

  • S. Sirohi,
  • A. Kumar,
  • S. M. Pandey
  • + 4 autorów
2023
Meta Tagi