Search
dr hab. inż. Beata Zima
Employment
- Associate professor at Institute of Ocean Engineering and Ship Technology
Research fields
Publications
Filters
total: 61
Catalog Publications
Year 2024
-
Corrosion damage identification based on the symmetry of propagating wavefield measured by a circular array of piezoelectric transducers: Theoretical, experimental and numerical studies
PublicationThe article investigates the results obtained from numerical simulations and experimental tests concerning the propagation of guided waves in corroded steel plates. Developing innovative methodologies for assessing corrosion-induced degradation is crucial for accurately diagnosing offshore and ship structures exposed to harsh environmental conditions. The main aim of the research is to analyze how surface irregularities affect...
-
Fracture surface topography measurements analysis of low-alloyed corrosion resistant steel after bending-torsion fatigue tests
PublicationIn this paper, an assessment of a topography measurement method for fracture surfaces of 10HNAP steel after bending-torsion fatigue tests was performed. Surface roughness was measured by using a non-contact Focus Variation Microscopy (FVM) technique in which the non-measured points (NMPs) and outliers (spikes) were removed by the application of general methods. The results revealed, that the optical measurement method introduced...
-
Guided wave propagation in debonding detection in CFRP-reinforced steel plate-like structures
PublicationThe present study investigates the guided wave propagation in multilayered steel specimens reinforced with carbon fiber reinforced polymer (CFRP) through theoretical, numerical, and experimental means. The effectiveness of externally bonded reinforcement (EBR) relies heavily on the bonding quality between the CFRP and the substrate. Premature debonding, a prevalent and hazardous defect, can arise from suboptimal manufacturing processes,...
-
Nondestructive corrosion degradation assessment based on asymmetry of guided wave propagation field
PublicationThe article presents the results of numerical and experimental investigation of guided wave propagation in steel plates subjected to corrosion degradation. The development of novel procedures allowing for the assessment of the corrosion degradation level is crucial in the effective diagnostics of offshore and ship structures that are especially subjected to aggressive environments. The study’s main aim is to investigate the influence...
-
Nondestructive global corrosion measurement using guided wavefield data
PublicationMetallic structures often face degradation, and corrosion ranks among the most prevalent forms of deterioration. Accurate quantification of corrosion is crucial, especially for structures exposed to harsh environmental conditions, such as marine vessels and offshore installations. Because the traditional measurement methods based on scanning by ultrasonic gauge are time-consuming and provide only rough information on the thickness...
-
The Influence of Global Corrosion Degradation on Localized Damage Detection Using Guided Waves
PublicationThis paper presents the results of a numerical analysis of the influence of corrosion degradation of metal plates on the wave propagation phenomenon. There are several different corrosion types, but general and pitting corrosion are the most common. General corrosion is more or less uniformly distributed over the entire exposed surface of the metal while pitting corrosion takes the form of localized cracks. Because the general...
Year 2023
-
A Numerical Study on Baseline-Free Damage Detection Using Frequency Steerable Acoustic Transducers
PublicationIn structural health monitoring (SHM) a considerable amount of damage detection algorithms based on guided waves (GW) have been developed. Most of them rely on extensive transducer networks, besides preliminary reference measurements of the structures. This originated a growing demand for hardware simplification and cost reduction of the wave-based SHM methods, driving the conception of new solutions enabling both: the reduction...
-
GUIDED WAVES IN SHIP STRUCTURAL HEALTH MONITORING – A FEASIBILITY STUDY
PublicationShips and offshore structures operate in a severe corrosion degradation environment and face difficulty in providing long- lasting corrosion protection. The Classification Societies recommend regular thickness measurements leading to structural component replacements, to ensure structural integrity during service life. The measurements are usually performed using ultrasonic thickness gauges and such an approach requires multiple...
-
Numerical and experimental investigation of guided ultrasonic wave propagation in non-uniform plates with structural phase variations
PublicationThe article presents the results of numerical and experimental investigations of guided wave propagation in aluminum plates with variable thickness. The shapes of plate surfaces have been specially designed and manufactured using a CNC milling machine. The shapes of the plates were defined by sinusoidal functions varying in phase shift, which forced the changes in thickness variability alongside the propagation path. The main aim...
-
Roughness evaluation of turned composite surfaces by analysis of the shape of Autocorrelation Function
PublicationIn this paper, the application of an Autocorrelation Function for the characterisation of surface topography was validated. The roughness evaluation of turned composite surfaces was supported by sophisticated studies of the Autocorrelation Function properties, considering especially the shape of the function. Details were measured with the optical method. The selection of the surface roughness evaluation procedures was carried...
-
Theoretical and experimental analysis of guided wave propagation in plate-like structures with sinusoidal thickness variations
PublicationGuided waves have attracted significant attention for non-destructive testing (NDT) and structural health monitoring (SHM) due to their ability to travel relatively long distances without significant energy loss combined with their sensitivity to even small defects. Therefore, they are commonly used in damage detection and localization applications. The main idea of incorporating guided waves in NDT and SHM is based on processing...
Year 2022
-
Corrosion degradation monitoring of ship stiffened plates using guided wave phase velocity and constrained convex optimization method
PublicationThe study presents an experimental investigation on the corrosion degradation level assessment using nondestructive wave-based methods. The degradation level of ship structural elements has been assessed in two different ways. The first one is based on the spectral decomposition and zero-crossing incorporated reconstruction of the dispersion curve approach of the antisymmetric Lamb wave mode and the best matching of the theoretical...
-
Data Compression in Ultrasonic Network Communication via Sparse Signal Processing
PublicationThis document presents the approach of using compressed sensing in signal encoding and information transferring within a guided wave sensor network, comprised of specially designed frequency steerable acoustic transducers (FSATs). Wave propagation in a damaged plate was simulated using commercial FEM-based software COMSOL. Guided waves were excited by means of FSATs, characterized by the special shape of its electrodes, and modeled...
-
Determination of stepped plate thickness distribution using guided waves and compressed sensing approach
PublicationGuided waves recently have attracted significant interest as a very promising research area. The signals registered by a specially designed sensor network are processed to assess the state of the tested structure. Despite the constant development of novel damage detection algorithms employing guided waves, the phenomenon of wave propagation still needs detailed recognizing and understanding for the further progress of non-destructive...
-
Experimental and numerical identification of corrosion degradation of ageing structural components
PublicationThe study presents experimental and numerical identification of corrosion degradation of thin-walled structural components employing guided wave propagation. The steel structural components are subjected to through-thickness varying corrosion degradation levels. The developed approach using the non-destructive guided wave-propagation quantifies the equivalent average corrosion degradation level by exploring a limited number of...
-
Research on Linear Actuators for Active Foil Bearings
PublicationActive foil bearings are a kind of gas foil bearing. They contain actuators which allow for modification of the bearing sleeve size and the shape of the lubrication gap. Rotor vibrations can be actively controlled by these changes. It is possible, among other things, to reduce the starting torque, control the vibration amplitude at different speeds and improve operational safety. Prototypes of active foil bearings are being developed...
-
The vibration-based assessment of the influence of elevated temperature on the condition of concrete beams with pultruded GFRP reinforcement
PublicationConcrete beams reinforced with glass fiber reinforced polymer (GFRP) bars subjected to elevated temperature have been experimentally studied. The influence of high temperatures on GFRP-reinforced concrete beams condition has been check both, destructively and nondestructively. The nondestructive tests foresaw vibration-based tests to obtain the natural frequency values after exposure to varying temperatures. The vibration-based...
Year 2021
-
Baseline-free debonding detection in reinforced concrete structures by elastic wave propagation
PublicationThe article presents the results of the numerical and experimental analysis concerning wave propagation in reinforced concrete (RC) beams with various extent of debonding between the steel rod and concrete cover. The main aim of the paper was to consider the unsolved research gaps, which considerably limit the application of wave-based methods in practice. The propagation of the flexural wave modes excited and registered on the...
-
Damage detection in plates based on Lamb wavefront shape reconstruction
PublicationMany of the current studies in the area of damage detection using elastic wave propagation are based on deploying sensor networks with a large number of piezoelectric transducers to detect small-size cracks. A major limitation of these studies is that cracks are usually larger and have different shapes in real cases. Moreover, using a large number of sensing nodes for damage detection is both costly and computationally intensive....
Year 2020
-
Debonding Size Estimation in Reinforced Concrete Beams Using Guided Wave-Based Method
PublicationThe following paper presents the results of the theoretical and experimental analysis of the influence of debonding size on guided wave propagation in reinforced concrete beams. The main aim of the paper is a development of a novel, baseline-free method for determining the total area of debonding between steel rebar embedded in a concrete cover on the basis of the average wave velocity or the time of flight. The correctness of...
-
Detection and size estimation of crack in plate based on guided wave propagation
PublicationThe paper presents results of the comprehensive theoretical and experimental investigation of crack detection in metallic plate using guided wave propagation. The main aim of the paper is to develop the novel method which would allow for linear crack size estimation with the use of minimal number of the transducers. In general, there exists the relation between length of the propagation path and the wave amplitude value. However,...
-
Evaluation of the resistance of steel–concrete adhesive connection in reinforced concrete beams using guided wave propagation
PublicationThe development of the nondestructive diagnostic methods is of significant importance in the last decades. A special attention is paid to diagnostics of reinforced concrete structures, which are very popular in the civil engineering field. A possible use of the guided waves in the estimation of the resistance of steel–concrete adhesive connection is studied in the following paper. The relationships relating adhesive connection...
-
Numerical Study of Concrete Mesostructure Effect on Lamb Wave Propagation
PublicationThe article presents the results of the numerical investigation of Lamb wave propagation in concrete plates while taking into account the complex concrete mesostructure. Several concrete models with randomly distributed aggregates were generated with the use of the Monte Carlo method. The influence of aggregate ratio and particle size on dispersion curves representing Lamb wave modes was analyzed. The results obtained for heterogeneous...
Year 2019
-
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublicationOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Guided Wave Propagation in Detection of Partial Circumferential Debonding in Concrete Structures
PublicationThe following article presents results of investigating the damage detection in reinforced concrete beams with artificially introduced debonding between the rod and cover, using a non-destructive method based on elastic waves propagation. The primary aim of the research was to analyze the possible use of guided waves in partial circumferential debonding detection. Guided waves were excited and registered in reinforced concrete...
-
Numerical investigation of the core eccentricity effect on wave propagation in embedded waveguide
PublicationThe paper presents results of theoretical and numerical investigation of guided wave propagation in two-layer bars with geometric imperfections in the form of eccentric location of steel core. Steel rod of diameter equal to 1 cm embedded in composite mortar-type cover with external diameter equal to 5 cm has been taken into consideration. Several different rods with variable size of eccentricity are analysed. Results for rods with...
-
Reference-free determination of debonding length in reinforced concrete beams using guided wave propagation
PublicationThis paper presents theoretical and experimental investigations of guided wave propagation in reinforced concrete beams, with pre-existing debonding between steel rebars and concrete blocks, for the purpose of damage detection. The primary aim of these investigations was a detailed analysis of the possible applications of wave propagation in single and multiple debonding detection in reinforced concrete structures and reference-free...
-
RMS-based damage detection in reinforced concrete beams: numerical simulations
PublicationImage-based damage detection methods using guided waves are well known and widely applied approaches in structural diagnostics. They are usually utilized in detection of surface damages or defects of plate-like structures. The article presents results of the study of applicability of imaging wave-based methods in detection in miniscule internal damage in the form of debonding. The investigations were carried out on numerical models...
Year 2018
-
Application of guided waves in the evaluation of steel-concrete adhesive connection
PublicationThe aim of the paper is the application of guided waves in the evaluation of a condition state of adhesive connection between steel and concrete. The study concerns a push-out specimen consisting of two steel plates glued to opposite faces of a concrete cube with the use of structural adhesive. Wave propagation in the specimen without external load is investigated both experimentally and numerically. The second stage of the investigation...
-
Guided ultrasonic waves for detection of debonding in bars partially embedded in grout
PublicationThis paper deals with theoretical, numerical and experimental investigations of guided wave propagation in multilayered cylindrical bars with pre-existing debonding. The research focuses on a complex description of the nature of the wave phenomena occurring in a debonded specimen with a special emphasis on the influence of the location of damage on the wave conversion and diffraction. Experimental non-destructive and destructive...
-
Guided waves for nondestructive diagnostics of embedded waveguides
PublicationThe thesis concentrates on comprehensive theoretical, numerical and experimental analysis of guided wave propagation in bars embedded in concrete or mortar. The investigations are focused on a particular type of objects representing a laboratory model of a ground anchor. Complex description of wave propagation phenomena in partially embedded bars is given and its application in...
-
Opracowanie opinii technicznej w zakresie występowania iniektu wewnątrz wskazanych przez Zleceniodawcę kanałów kablowych mostu MA-09 w ciągu drogi S7
PublicationCelem opracowania jest ocena występowania iniektu wewnątrz wskazanych przez Zleceniodawcę kanałów kablowych mostu MA-09 realizowanego w ramach zadania „Budowa drogi S-7 Gdańsk (A-1) – Elbląg (S-22) odc. Koszwały (DK nr 7, W. Koszwały) - Elbląg (z węzłem Kazimierzowo) z podziałem na 2 części. Zadanie 1: Koszwały – Nowy Dwór Gdański“. Zakres opracowania obejmuje: • zapoznanie się z dokumentacją techniczną obiektu, • wizję lokalną, •...
-
Pełnienie nadzoru naukowego nad naprawą po awarii i dalszą budową konstrukcji mostu M-78. Ekspertyza techniczna
PublicationCelem opracowania jest szczegółowa analiza mostu M-78 wykonywanego w ramach zadania „Projekt i budowa drogi ekspresowej S-6 na odcinku od węzła „Kołobrzeg Zachód" /bez węzła/ węzeł „Ustronie Morskie" /z węzłem/ oraz „Budowa obwodnicy m. Kołobrzeg w ciągu drogi krajowej nr 11” ”. Opracowanie w sposób szczegółowy przedstawia prace zrealizowane na potrzeby wydanych opinii technicznych w trakcie realizacji mostu. Zakres opracowania...
Year 2017
-
Elastic wave propapagation in diagnostics of self-drilling system of grouted anchors
PublicationThe paper presents an experimental investigation of elastic wave propagation in a self-drilling hollow bar system, which is commonly used in geotechnical industry as the element of grouted ground anchors and soil nails. The single self-drilling hollow bar and self-drilling system of two bars connected by a coupler were considered. Longitudinal waves were excited at one end of the bar and registered at both ends, by means of PZT...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
Non-destructive inspection of ground anchors using guided wave propagation
PublicationThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
Opracowanie opinii dot. wpływu drgań wywołanych ruchem taboru kolejowego na konstrukcję części garażowej obiektu „Targ Rakowy i Sienny" w kompleksie Forum Gdańsk oraz przebywających w niej ludzi po zmianie układu konstrukcyjnego
PublicationCelem opracowania jest wykonanie opinii dotyczącej wpływu drgań wywołanych ruchem taboru kolejowego na konstrukcję sekcji garażowej obiektu „Targ Rakowy i Sienny" w kompleksie Forum Gdańsk oraz przebywających w niej ludzi po zmianie układu konstrukcyjnego.
Year 2016
-
DETECTION OF DEBONDING IN STEEL BARS EMBEDDED IN CONCRETE USING GUIDED WAVE PROPAGATION
PublicationThe paper presents a non-destructive diagnostic technique based on guided wave propagation phenomenon used to assess the adhesive bonding between a steel bar and a concrete cover. Double-layered cylindrical specimens with different levels of debonding and its location were investigated. The influence of bonding length on the excitation of multiple modes of longitudinal guided waves was analysed. Numerical simulations of guided...
-
Ekspertyza techniczna dot. wpływu drgań na obiekt „Targ Rakowy i Sienny” w kompleksie Forum Gdańsk
PublicationEkspertyza dotyczy obiektu przekrywającego tory kolejowe w rejonie Targu Siennego i Targu Rakowego w Gdańsku stanowiącego część kompleksu Forum Gdańsk określającej wpływ ruchu kolejowego na konstrukcję oraz na użytkowników obiektu.
-
Experimental and numerical analysis of wave propagation in ground anchors
PublicationThe article focuses on wave propagation phenomenon in ground anchors. The main aim of the investigation is the non-destructive diagnostics and the assessment of the state of ground anchors, using the guided wave propagation method. Laboratory models of anchors with different lengths of the anchor body were tested and voltage signals of propagating waves were registered at several locations. For all tested specimens corresponding...
-
Guided waves for monitoring of plate structures with linear cracks of variable length
PublicationDamage occurring at the work of plate structures may grow to a considerable size. The joint action – the detection of a defect at the earliest possible stage, the monitoring of its growth and the determination of its critical size in the context of structural reliability allows optimizing the cost of the maintenance and repair of structural elements. Thus the development of monitoring systems for permanent observation of fault...
-
Przeprowadzenie pomiarów i wykonanie opinii mającej na celu określenie wpływu drgań na halę magazynową oraz przebywających w niej i pomieszczeniach biurowych ludzi
PublicationW opracowaniu przedstawiono rezultaty prac eksperckich, kóre polegały na przeprowadzeniu pomiarów i wykonaniu opinii mającej na celu określenie wpływu drgań wywołanych przez pracujące urządzenia na halę magazynową zlokalizowaną przy ul. Energetycznej 9 w Kowalach oraz przebywających w pomieszczeniach biurowych ludzi.
-
Wykorzystanie propagacji fal sprężystych w ocenie efektywnej długości zakotwienia
PublicationW pracy przedstawiono wyniki analizy numerycznej dotyczącej propagacji fal w prętach otulonych materiałem kompozytowym.
Year 2015
-
Analiza możliwości oceny stanu technicznego kotew gruntowych za pomocą propagacji fal prowadzonych
PublicationW pracy przedstawiono identyfikację długości swobodnej cięgna kotew gruntowych z wykorzystaniem metody propagacji fal prowadzonych. Badania doświadczalne propagacji fal zostały prowadzone dla modeli kotew w skali laboratoryjnej z różnymi długościami buławy.
-
Application of wavelet transform in analysis of guided wave propagation signals for damage detection in a steel plate
PublicationThe paper presents results of experimental investigations on damage detection using guided wave propagation technique. The tested specimen was a steel plate with a defect in the form of a rectangular notch. Lamb waves were excited by a PZT actuator and sensed by a laser vibrometer. Since reflections from damage in registered signals are often masked by measurement noise, for identification of time of reflections from damage, continuous...
-
Ekspertyza techniczna dot. odpowiedzi dynamicznej obiektu „Targ Rakowy i Sienny” – CZĘŚĆ 1 - BADANIA
PublicationZakres wykonanej ekspertyzy obejmował wykonanie odpowiedzi dynamicznej istniejącej części Forum Gdańsk wywołanej poruszającym się taborem kolejowym.
-
Ekspertyza techniczna dotycząca określenia wpływu drgań dynamicznych na konstrukcję chłodni na terenie zakładu Mondi w Świeciu
PublicationPrzedmiotem ekspertyzy było wykonanie badań określających wpływ drgań dynamicznych spowodowanych pracą wentylatorów na konstrukcję budynku chłodni.
-
Ekspertyza techniczna dotycząca określenia wpływu drgań wywołanych montażem grodzic PCV przy ul. Sołeckiej 10 w Gdańsku.
PublicationCelem ekspertyzy było określenie wpływu drgań dynamicznych spowodowanych wbijaniem ścianki szczelnej na konstrukcje przyległych budynków.
-
Ekspertyza techniczna dotycząca wpływu drgań na kolumny betonowe wykonywane w ramach budowy drogi ekspresowej S19 Lubartów-Kraśnik
PublicationCelem ekspertyzy było określenie wpływu drgań generowanych w trakcie wytwarzania nowej kolumny betonowej na już istniejące, które zostały wykonane wcześniej.
-
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublicationThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
seen 10520 times