dr inż. Michał Mazur
Publikacje
Filtry
wszystkich: 48
Katalog Publikacji
Rok 2024
-
The clamping selection method to reduce the vibration of large-size workpieces during the face milling process
PublikacjaThe article introduces a method for selecting the best clamping conditions to obtain vibration reduction during milling of large-size workpiece. It is based on experimental modal analysis performed for a set of assumed, fixing conditions of a considered workpiece to identify Frequency Response Functions (FRFs) for each tightening torque of the mounting screws. Simulated plots of periodically changing nominal cutting forces are...
Rok 2022
-
Adjusting the Stiffness of Supports during Milling of a Large-Size Workpiece Using the Salp Swarm Algorithm
PublikacjaThis paper concerns the problem of vibration reduction during milling. For this purpose, it is proposed that the standard supports of the workpiece be replaced with adjustable stiffness supports. This affects the modal parameters of the whole system, i.e., object and its supports, which is essential from the point of view of the relative tool–workpiece vibrations. To reduce the vibration level during milling, it is necessary to...
Rok 2021
-
A method of predicting the best conditions for large-size workpiece clamping to reduce vibration in the face milling process
PublikacjaThe paper presents an innovative method of solving the problem of vibration suppression during milling of large-size details. It consists in searching for the best conditions for clamping the workpiece based on a rapid modal identification of the dominant natural frequencies only and requires repetitive changes in the tightening torque of the clamping screws. Then, by estimating the minimum work of the cutting forces acting in...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublikacjaThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures
PublikacjaAbstract: The paper presents an original method concerning the problem of vibration reduction in the general case while milling large-size and geometrically complex details with the use of an innovative approach to the selection of spindle speed. A computational model is obtained by applying the so-called operational approach to identify the parameters of the workpiece modal model. Thanks to the experimental modal analysis results,...
-
An Improved Method of Minimizing Tool Vibration during Boring Holes in Large-Size Structures
PublikacjaThe paper presents a thoroughly modified method of solving the problem of vibration suppression when boring large-diameter holes in large-size workpieces. A new approach of adjusting the rotational speed of a boring tool is proposed which concerns the selection of the spindle speed in accordance with the results of the simulation of the cutting process. This streamlined method focuses on phenomenological aspects and involves the...
-
Estimation of structural stiffness with the use of Particle Swarm Optimization
PublikacjaThe paper presents the theoretical background and four applications examples of the new method for the estimation of support stiffness coefficients of complex structures modelled discretely (e.g. with the use of the Finite Element Model (FEM) method based on the modified Particle Swarm Optimization (PSO) algorithm. In real-life cases, exact values of the supports’ stiffness coefficients may change for various reasons...
-
Metoda doboru współczynników sztywności podpór mocujących podczas frezowania wielkogabarytowych przedmiotów podatnych z wykorzystaniem sterowania optymalnego w układzie semiaktywnym
PublikacjaW pracy zaproponowano nową metodę doboru w trybie on-line współczynników sztywności zamocowania wielkogabarytowego przedmiotu obrabianego do stołu frezarki, bazującą na koncepcji sterowania optymalnego przy energetycznym wskaźniku jakości w układzie we współrzędnych hybrydowych. Jednak znane z poprzednich opracowań autorskich równanie dynamiki wielowymiarowego układu sterowanego sprowadza się w tym przypadku do postaci, gdzie składowymi...
Rok 2020
-
FPGA Based Real Time Simulations of the Face Milling Process
PublikacjaThe article presents a successful implementation of the milling process simulation at the Field-Programmable Gate Array (FPGA). By using FPGA, very rigorous Real-Time (RT) simulation requirements can be met. The response time of the FPGA simulations is significantly reduced, and the time synchronization is better than in a typical RT system implemented in software. The FPGA-based approach is characterized by enormous flexibility...
-
Optymalizacja prędkości obrotowej narzędzia podczas frezowania przedmiotów wielkogabarytowych
PublikacjaPrzedstawiono nową metodę wyznaczania optymalnej prędkości obrotowej narzędzia podczas frezowania przedmiotów wielkogabarytowych. Parametry modelu obliczeniowego (modalnego) przedmiotu obrabianego są wyznaczane z wykorzystaniem jedynie eksperymentalnej analizy modalnej. To ostatnie umożliwia eliminację pracochłonnego etapu modelowania przedmiotu, jakim jest stosowane dotychczas tworzenie i walidacja modelu MES. Otrzymany w ten...
Rok 2019
-
Algorytmy roju w modelowaniu MES, czyli jak stado szpaków może pomóc inżynierowi
PublikacjaW poprzednich numerach „Pisma PG” prof. Jacek Rumiński przedstawił możliwości i perspektywy rozwoju sztucznej inteligencji (SI), zwłaszcza w kontekście notujących obecnie liczne sukcesy sztucznych sieci neuronowych. Jednak nie tylko budowa układu nerwowego jest inspiracją dla nowych metod SI. Ciekawą grupą metod są algorytmy wzorujące się na zachowaniu zwierząt, zwłaszcza na ich zdolnościach socjalnych i współpracy przy stawianiu...
-
ESTYMACJA WSPÓŁCZYNNIKÓW SZTYWNOŚCI ZAMOCOWANIA PODATNEGO PRZEDMIOTU OBRABIANEGO NA STOLE FREZARKI
PublikacjaW pracy przedstawiono metodę estymacji współczynników sztywności Elementów Sprężystych (ES) modelujących zamocowanie podatnego wielkogabarytowego przedmiotu obrabianego na stole frezarki. Proponowana metoda bazuje na algorytmie optymizacji za pomocą roju cząstek (ang. Particle Swarm Optimization), który pozwala na uzyskanie dobrej zgodności (aktualizacji) modelu Metody Elementów Skończonych (MES) z modelem pochodzącym z identyfikacji...
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublikacjaThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
Minimization of vibrations during milling of flexible structures using mechatronic design techniques
PublikacjaThe paper presents an innovative effective method of minimizing vibrations during milling of flexible structures, using a new vibration suppression method based on a workpiece holder with adjustable support stiffness. The proposed method is rooted in mechatronic design techniques, which can become a standard procedure for optimizing the milling process.
-
Optimization of the spindle speed during milling of large-sized structures with the use of technique of Experiment-Aided Virtual Prototyping
PublikacjaIn the paper are presented considerations concerning vibration suppression problems during milling of large-sized workpieces with the use of innovative method of matching the spindle speed of cutting tool. It depends on repeatable change of the spindle speed value as soon as the optimal vibration state of the workpiece approaches. The values of dominant “peaks” in the frequency spectra and the Root Mean Square (RMS) values of time...
-
Optymalizacja prędkości obrotowej narzędzia podczas wytaczania przedmiotów wielkogabarytowych
PublikacjaPrzedstawiono nową metodę wyznaczania optymalnej prędkości obrotowej narzędzia podczas wytaczania przedmiotów wielkogabarytowych, na podstawie symulacji procesu obróbki. Przeprowadzane są one dla modelu obliczeniowego wirującego narzędzia, dostrojonego do wyników testów modalnych, wraz z przyjętym modelem procesu skrawania. Ocenie podlegają wartości skuteczne (RMS) poziomu drgań w dziedzinie czasu oraz wartości dominujących amplitud...
-
Simplified Map-based Selection of Optimal Spindle Speeds When Milling Complex Structures
PublikacjaIn the paper a method for selecting optimal spindle speeds for complex structures during milling operations is presented. It is based on the selection of the spindle speed in accordance with a simple equation resulting from the minimisation of vibration energy, which leads to the minimisation of the work of cut-ting forces presented in previous elaborations by the authors [1]. Optimal spindle speeds are obtained for many points...
Rok 2018
-
Badanie algorytmu identyfikacji parametrów modalnych wykorzystującego wiele rojów PSO pod kątem odporności na zakłócenia pomiarowe
PublikacjaW pracy przedstawiono wpływ zakłóceń pomiarowych na skuteczność algorytmu wykorzystującego wiele rojów PSO do identyfikacji parametrów modalnych w dziedzinie częstotliwości. W pracy przedstawiono wpływ poziomu szumu występującego w sygnale symulującym warunki pomiarowe przy rożnych poziomach zakłóceń. Ponadto otrzymane wyniki porównano z wynikami dla metod ERA i pLSCF-d. Uzyskane rezultaty wskazują, że proponowany algorytm w większości...
-
Optymalizacja docisku mocowania podatnego przedmiotu obrabianego podczas frezowania
PublikacjaPrzedstawiono nową metodę nadzorowania drgań podatnego przedmiotu obrabianego podczas frezowania czołowego, polegającą na optymalizacji docisku zamocowania na podstawie szybkiej analizy modalnej. Wymaga ona powtarzalnej zmiany momentu dokręcenia śrub mocujących. Oszacowanie minimalnej pracy sił skrawania na kierunku szerokości warstwy umożliwia prognozowanie optymalnej konfiguracji zamocowania przedmiotu obrabianego. Skuteczność...
-
Optymalizacja prędkości obrotowej narzędzia podczas frezowania - procedura eksploatacyjna
PublikacjaW pracy zaproponowano metodę wyznaczenia optymalnej prędkości obrotowej narzędzia podczas frezowania na podstawie symulacji procesu obróbki przeprowadzonej dla uproszczonego modelu przedmiotu wraz z modelem procesu skrawania. Parametry modelu określane są bezpośrednio na podstawie wyników identyfikacji (eksperymentalna analiza modalna) co znacznie skraca czas doboru prędkości względem pełnej procedury modalnej. Tworzony jest model...
wyświetlono 2487 razy