Search
dr inż. Mariusz Jaczewski
Employment
- Assistant professor at Department of Transportation Engineering
Research fields
Publications
Filters
total: 64
Catalog Publications
Year 2024
-
Effect of strain level on the stiffness of cold recycled bituminous mixtures
PublicationCold recycling is a sustainable technology for the rehabilitation of bitumi-nous pavements. This study investigates the stiffness response of cement-bitumen treated materials (CBTM)manufactured with 80% reclaimed asphalt and treated with 2.0% Portland cement and 4.0% bitumen emulsion. Indirect tensile stiffness modulus tests were carried out to assess the strain dependence of stiffness at target horizontal deformation levels between...
-
One year performance evaluation of low volume road with cold recycled base course on the basis of FWD and Dynamic Modulus tests
PublicationArticle presents results of assessment of performance of trial section of flexible pavement with cold recycled base constructed on low volume road within typical contract conditions. Performance evaluation was made based on Falling Weight Deflectometer (FWD) test performed during construction stage – 2 times on the top of cold recycled base course – 28 and 180 days after compaction of base course and 2 times on the top of the wearing...
-
Strain-dependent behaviour of cold recycled material mixtures in cyclic compression tests
PublicationThe purpose of the study is to evaluate strain-dependent behaviour of Cold Recycled Material (CRM) mixtures using three frameworks typically applied for Hot Mix Asphalt (HMA): linear viscoelastic (LVE) limits; non-linearity directions; changes in rheological model parameters. To this aim, the complex modulus of three CRM mixtures with different bitumen-to-cement ratio (0.2, 0.6 and 1.8) was measured in cyclic compression mode,...
Year 2023
-
ANALIZA WYBRANYCH CECH MECHANICZNYCH MIESZANEK MINERALNO-CEMENTOWO-EMULSYJNYCH (MCE)
PublicationW ostatnich latach mieszanki mineralno-cementowo-emulsyjne (MCE) stają się materia³em coraz częściej wykorzystywanym przy projektowaniu remontów i przebudów nawierzchni z wykorzystaniem recyklingu. Materiał ten zyskuje coraz większą popularność, ponieważ pozwala w sposób racjonalny i bez uszczerbku dla środowiska naturalnego ponownie wykorzystać materiały pochodzące z rozbiórki starych nawierzchni bitumicznych, w tym również materiały...
-
Evaluation of thermal cracking probability for asphalt concretes with high percentage of RAP
PublicationThe paper presents determination of the probability of thermal cracking of asphalt mixtures with different reclaimed asphalt pavement (RAP) content on the basis of laboratory tests and analytical evaluation using thermal stress development method. Probability was evaluated taking into consideration: the type and gradation of the mixture and the quality and content of RAP. Thermal stresses were determined using two models: elastic and...
-
Factors affecting low-temperature cracking of asphalt pavements: analysis of field observations using the ordered logistic model
PublicationAccurate identification of factors that primarily affect the number of low-temperature cracks is crucial for selection of road materials and planning of pavement maintenance. Field investigations of lowtemperature cracks were performed in the years 2014 and 2020 on the same 68 road sections being in service in typical traffic conditions. The collected data were statistically analysed using the ordered logistic regression model....
-
Stiffness of cold-recycled mixtures under variable deformation conditions in the IT-CY test
PublicationStiffness modulus belongs to the most important properties describing the cold-recycled mixtures (CRM) in terms of their usability in road pavement structures. Previous research proved that this property is strongly dependent on the scheme and conditions of the test (temperature and time of loading) and the time that has passed since the compaction of the specimen or pavement layer. It is a result of the influence of two different...
-
The dependence of linear viscoelasticity limits of cold-recycled mixtures on time of curing and compaction method
PublicationCold-recycled mixtures are currently among the most widely used and investigated methods that enable recycling of old pavement structures in an environmentally friendly manner. Upon milling, the old pavement structure – whose gradation can be improved with addition of virgin aggregate – is mixed and compacted at ambient temperature. The main binding agents are bituminous emulsion and cement. Due to their dual binding behaviour,...
Year 2022
-
Cold recycled mixtures for binder courses - laboratory evaluation of mechanical properties
PublicationCold recycled mixtures composed with cement and bituminous emulsion are nowadays commonly used material for base layer. Typical pavement with cold recycled mixtures usually consists of two asphalt courses (wearing and binding course) constructed over cold recycled base. Therefore the next step in cold recycling is possibility of design of binding courses with recycled materials, but with potential to obtain high quality mixtures...
-
COMMON FIRE CAUSES IN INDUSTRIAL SITES
PublicationChapter presents common causes of fires in industrial places
-
Field Evaluation of High Modulus Asphalt Concrete Resistance to Low-Temperature Cracking
PublicationHigh-modulus asphalt concrete has numerous advantages in comparison to conventional asphalt concrete, including increased resistance to permanent deformations and increased pavement fatigue life. However, previous studies have shown that the construction of road pavements with High Modulus Asphalt Concrete (HMAC) may significantly increase the risk of low-temperature cracking. Those observations were the motivation for the research...
-
FIRE RISK ASSESSMENT IN INDUSTRIAL PREMISES
PublicationChapter presents different aspects of fire risk assessment in industrial sites
-
INDFIRES PROJECT AND SITUATIONAL INDUSTRIAL FIRE REPORTS OF PARTNER COUNTRIES
PublicationChapter contains information regarding project and situational reports from all participants.
-
INDUSTRIAL FIRE SAFETY REQUIREMENTS IN PARTNER COUNTRIES
PublicationChapter contains information regardin law regulations of fire safety for constructions in countris participating in project.
-
Preliminary study of linear viscoelasticity limits of cold recycled mixtures determined in Simple Performance Tester (SPT)
PublicationThe publication presents methodology developed for determination of linear viscoelasticity limits for cold recycled mixtures with cement and bituminous emulsion using Simple Performance Tester (SPT). Methodology was verified on reference materials (PCV and steel dummy specimens, cement concrete and asphalt concrete) to comply with elasticity and viscoelasticity theory. The developed methodology enabled determination of linear viscoelasticity...
-
The innovative approach for using pavement as a fire prevention measure in tunnels
PublicationThe paper consists of two main parts: first presents study regarding the typically used pavement structures in tunnels and the second part: the first fire trials of the poroelastic SEPOR (Safe, Eco-friendly POroelastic Road Surface) mixture which was designed to be used among other uses in tunnels. In the first part of the paper different pavement materials, such as cement concrete, asphalt concrete, stone mastic asphalt and porous...
Year 2021
-
BINDER COURSES USING COLD RECYCLED MIXTURES – A NOVEL CONCEPT IN COLD RECYCLING
PublicationCold recycling with cement and bituminous emulsion is one of the most environmentally friendly techniques to maximize the reuse of reclaimed asphalt (RA) collected during demolition of roads. Cold recycled mixtures are commonly used for base courses in construction or rehabilitation of flexible and semi-rigid pavements. Current experiences demonstrated that cold recycling with appropriate requirements and technical recommendations...
-
Comparative Study of the Mechanical Behaviour of Bitumen- and Cement-Dominated Mixtures with Reclaimed Asphalt
PublicationThe bitumen emulsion-based recycling is a commonly used maintenance treatment in the rehabilitation of low-and medium-volume roads in Europe. Nevertheless, the wide range of climatic conditions across the continent resulted in the variety of mixture concepts and the requirements being adopted for various local conditions. In this regard, the most commonly used parameter to distinguish between the main mixture concepts is bitumen...
-
Optimisation and field assessment of poroelastic wearing course bond quality
PublicationCompared to typical asphalt mixtures, poroelastic mixtures are characterised by high porosity and high flexibility, which are desirable for traffic noise reduction. However, the same properties increase the risk of debonding from the lower layer, which is a significant source of premature damage. The study investigates which of the factors – tack coat agent, type and texture of the lower layer – have the greatest impact on interlayer...
-
The Influence of Cement Type on Early Properties of Cold In-Place Recycled Mixtures
PublicationCold in-place recycling is a commonly used maintenance treatment in rehabilitation of low and medium volume roads in Poland. Typically, two types of binding agents are used—cement and bituminous emulsion (or foamed bitumen).Due to the harsh Polish climate with many freeze/thaw cycles and frequent occurrence of saturated conditions, the used amounts of cement are higher than those commonly used in warmer parts of Europe. While there...
Year 2020
-
Effect of bitumen characteristics obtained according to EN and Superpave specifications on asphalt mixture performance in low-temperature laboratory tests
PublicationThe paper aims to identify those characteristics of bitumen which have the greatest impact on asphalt mixture low-temperature performance. It was observed that stiffness and m-value of bitumen from BBR test were moderately related to stiffness and m-value of asphalt mixture obtained from 3 PB test. Simultaneously those rheological properties significantly impact on cryogenic stresses induced during TSRST test. The multiple regression...
-
The influence of combination of binding agents on fatigue properties of deep cold in-place recycled mixtures in Indirect Tensile Fatigue Test (ITFT)
PublicationThe publication presents fatigue properties of cold recycled mixtures for eight combinations of binding agents (cement and bituminous emulsion). Cold recycled mixtures were evaluated in Indirect Tensile Fatigue Test (ITFT) at the temperature of 20 C in controlled stress mode. As a function of horizontal stress, fatigue life is strongly influenced by combination of the binding agents. When fatigue life is analyzed as a function...
Year 2019
-
Application and evaluation of M-EPDG for performance analysis of Polish typical flexible and rigid pavements
PublicationThe main goal of the paper is to implement and evaluate the M-EPDG and the software AASHTOware to analyse the performance of new flexible and rigid pavements designed according to the Polish catalogues, which are comparable with analogous catalogues used in other European countries. For this purpose the site-specific inputs for Poland were determined and described in the paper as well as compared to the default input data used...
-
Asphalt concrete subjected to long-time loading at low temperatures – Deviations from the time-temperature superposition principle
PublicationThe article presents the observed deviations from the time-temperature superposition principle of asphalt concretes, tested in the bending beam creep test at low temperatures for a long time of loading. In almost all tested asphalt concretes, deviations appeared after 500 s of loading at the temperature of -10 C. Some types of bitumen presented deviations at other temperatures – usually the harder the grade of the bitumen, the...
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublicationThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
Evaluation of the stiffness modulus and phase angle of cold in-place recycled mix-tures for long curing periods
PublicationArticle presents the changes inbehaviour of cold-in place recycling mixtures made using cement and bituminous emulsion (CIR mixtures) after anelongated time of curing. Most of the available literatureregarding change instiffness modulus and phase angle presents resultsfor a maximum of several dozen days,which makesit difficult to predict the behaviour over the whole life of the compacted layer. The article...
-
Impact of reclaimed asphalt pavement (RAP) on low-temperature properties of asphalt concrete
PublicationHot mix recycling is a practice which enables reusing materials from old asphalt pavements. Current Polish regulations allow usage of RAP only for binder and base courses, and its amount is limited. Asphalt mixtures with RAP material have to fulfil requirements stated for typical asphalt mixtures. The research presents low-temperature properties of twelve different asphalt concretes with RAP material, determined using three-point...
-
Influence of cooling rate and additives on low-temperature properties of asphalt mixtures in the TSRST
PublicationThe paper presents the results and analysis of low-temperature properties of asphalt mixtures according to Thermal Stress Restrained Specimen Test (TSRST) and Indirect Tensile Test methods. Different groups of bitumen were investigated: neat, SBS-modified and highly SBS-modified. Influence of cooling rates (1 C/h, 3 C/h, 5 C/h and 10 C/h) and additives (aramid fibres and crumb rubber) was identified as well. Moreover, for each...
-
Przegląd nanododatków stosowanych w warstwach asfaltowych nawierzchni drogowych
PublicationJednym z kierunków rozwoju technologii materiałowych jest nanotechnologia rozumiana jako dziedzina zajmująca się zastosowaniem nanododatków do wytwarzania nowych materiałów oraz ich wpływem na parametry modyfikowanych materiałów. W ostatnich latach nanotechnologia wkracza do technologii modyfikacji asfaltów stosowanych w nawierzchniach drogowych. W artykule przedstawiono stosowane obecnie w budownictwie drogowym nanododatki oraz...
Year 2018
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublicationLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Ocena terenowa spękań niskotemperaturowych i nośności nawierzchni wybranych odcinków dróg w Polsce Północno-Wschodniej
PublicationArtykuł przedstawia porównanie zachowania się wybranych odcinków dróg w Polsce Północno-Wschodniej wybudowanych w typowych warunkach kontraktowych, w których w podbudowach zastosowano typowe betony asfaltowe oraz betony asfaltowe o wysokim module sztywności. Ocena terenowa skupiała się na wyznaczeniu ilości spękań poprzecznych o charakterze niskotemperaturowym, ocenie nośności nawierzchni oraz jakości transferu obciążeń w obrębie...
-
The Impact of Long-Time Chemical Bonds in Mineral-Cement-Emulsion Mixtures on Stiffness Modulus
PublicationDeep cold in-place recycling is the most popular method of reuse of existing old and deteriorated asphalt layers of road pavements. In Poland, in most cases, the Mineral-Cement-Emulsion mixture technology is used, but there are also applications combining foamed bitumen and cement. Mineral-Cement-Emulsion mixtures contain two different binding agents – cement as well as asphalt from the asphalt emulsion. Asphalt creates asphalt...
Year 2017
-
Comparison of low-temperature cracks intensity on pavements with high modulus asphalt concrete and conventional asphalt concrete bases
PublicationHigh modulus asphalt concrete (HMAC) base courses provide very good resistance to rutting and fatigue but they can increase the risk of low-temperature cracking as compared with conventional asphalt concrete (AC). The article presents the comparison of these two road materials in terms of low-temperature cracking. The statistical method based on the ordered logistic regression model was used. The analysis was based on results of...
-
Evaluation of Low Temperature Properties of Rubberized Asphalt Mixtures
PublicationThe paper presents low-temperature test results of asphalt mixtures designed with use of bitumen modified by crumb rubber and also SBS polymer. Laboratory tests were conducted on two types of asphalt mixtures for wearing course – stone matrix asphalt (SMA 8) and porous asphalt (PA 8). This paper presents results of the following laboratory tests at low temperatures: TSRST test, three point bending creep test, fracture toughness...
-
Field investigation of low-temperature cracking and stiffness moduli on selected roads with conventional and high modulus asphalt concrete
PublicationHigh Modulus Asphalt Concrete (HMAC) was introduced in Poland as a one of the solutions to the problem of rutting, type of deterioration common in the 1990s. After first encouraging trials in 2002 HMAC was widely used for heavily loaded national roads and motorways. However some concerns were raised about low-temperature cracking of HMAC. This was the main reason of the studies presented in this article were started. The article...
-
New polish catalogue of typical flexible and semi-rigid pavements
PublicationThe paper covers the following topics important for the development of the new Polish Catalogue of typical flexible and semi-rigid pavements: reasons for preparing the new issue of the Catalogue of typical flexible and semi-rigid pavements, items introduced in the new issue, organise the terminology related to pavements, design traffic calculations and new equivalent axle load factors,...
-
Ocena właściwości niskotemperaturowych mieszanek mineralno-asfaltowych z asfaltem modyfikowanym SBS i gumą
PublicationW artykule przedstawiono wyniki badań przeprowadzonych w niskich temperaturach dla mieszanek mineralno-asfaltowych zaprojektowanych z użyciem asfaltów modyfikowanych miałem gumowym oraz polimerem SBS. Badania laboratoryjne zostały przeprowadzone dla dwóch rodzajów mieszanek mineralno-asfaltowych do warstwy ścieralnej – mastyksu grysowego (SMA 8) i asfaltu porowatego (PA 8). W niniejszym artykule przedstawiono wyniki następujących...
-
Ocena wrażliwości projektu konstrukcji nawierzchni trasy głównej drogi ekspresowej S3 Nowa Sól – Legnica, Zadanie IV
PublicationCelem pracy jest ocena wrażliwości projektu konstrukcji nawierzchni trasy głównej drogi ekspresowej S3 odcinek Nowa Sól – Legnica, Zadanie IV, na zmiany parametrów fizycznych i mechanicznych warstw asfaltowych w stosunku do założeń projektowych.
-
The Influence of Binding Agents on Stiffness of Mineral-cement-emulsion Mixtures
PublicationThis paper attempts to determine the behavior of mineral-cement-emulsion mixture (MCE) under load, whether is it similar to asphalt mixtures (viscoelastic behavior) or to cement treated materials (elastic behavior). To answer this question nine mineral- cement-emulsion mixtures with different combinations of cement and emulsion content were tested in laboratory using Simple Performance Test (SPT). For each mixture stiffness moduli...
-
The long-term properties of mineral-cement-emulsion mixtures
PublicationThis publication presents evaluation of long-term behavior of mineral-cement-emulsion (MCE) mixtures. MCE mixtures are among the major products of cold recycling of old asphalt pavements. They are composed by binding of the old materials reclaimed from the pavement and new mineral aggregate using two different binding agents – cement and bituminous emulsion. While bituminous emulsion dissolutes and binds materials quite fast, it...
-
Wpływ zawartości środków wiążących na sztywność mieszanek mineralno-cementowo-emulsyjnych
PublicationW artykule podjęto próbę ustalenia, i jest zachowanie się mieszanek mineralno-cementowo-emulsyjnych (MCE). Czy pod obciążeniem jest bardziej zbliżone do mieszanek mineralno-asfaltowych (materiały o charakterze lepkosprężystym) czy też mieszanek związanych cementem (materiały o charakterze sprężystym). Przebadano dziewięć mieszanek mineralno-cementowo-emulsyjnych o zróżnicowanych kombinacjach obu środków wiążących – cementu oraz...
Year 2016
-
Badania asfaltów 35/50 i 50/70 produkowanych różnymi metodami
PublicationWalidacja laboratoryjna asfaltów przeznaczonych do budowy dróg poprzez badanie właściwości fizyko-mechanicznych i eksploatacyjnych mieszanek mineralno-asfaltowych z zastosowaniem asfaltów 35/50 i 50/70 produkowanych różnymi metodami
-
Modelling of Asphalt Mixes under Long Time Creep at Low Temperatures
PublicationProper description of asphalt mixtures behavior under long time load is one of the most important factors in analyses of strain and stress relations at low temperatures both from traffic and environmental loads. For example different models of thermal stress accumulation require different approaches of description of asphalt concrete. But in all cases it is required to describe its behavior under long time loading, which in some...
-
The Impact of Homogeneity of High Modulus Asphalt Concrete Layer on Low-Temperature Cracking
PublicationDuring winter season of 2012 numerous transverse cracks developed in high-modulus asphalt concrete (HMAC) base of newly constructed motorway. Pavement cracked both in transverse joint locations and in the area between them. Research which was conducted during investigation of the causes and mechanisms of cracking consisted of: field examination, laboratory testing of specimens cored out of the existing pavement, computational analyses...
-
Właściwości niskotemperaturowe betonów asfaltowych o wysokim module sztywności (AC-WMS) w badaniach trzypunktowego zginania
PublicationArtykuł przedstawia właściwości niskotemperaturowe betonów asfaltowych o wysokim module sztywności. Przedstawione wyniki zostały uzyskane w dwóch badaniach zginania trzypunktowego próbek belkowych: ze stałą prędkością przemieszczenia oraz pod stałym obciążeniem. Obie te metody są od dawna stosowane na Politechnice Gdańskiej do oceny właściwości niskotemperaturowych betonów asfaltowych. Badaniu poddano pięć betonów asfaltowych –...
Year 2015
-
Badania spękań niskotemperaturowych podbudów a AC WMS na nowobudowanej autostradzie A1 w Polsce. Część 1 - Badania terenowe i laboratoryjne
PublicationW artykule przedstawiono problem niskotemperaturowych spękań poprzecznych, które powstały na podbudowach z betonu asfaltowego o wysokim module sztywności AC WMS. Liczne spękania niskotemperaturowe powstały na analizowanych podbudowach AC WMS podczas okresu zimowego w 2012 r. zanim została zakończona cała konstrukcja nawierzchni. Spękania powstały zarówno na połączeniach technologicznych, jak i pomiędzy nimi. Problem taki nie wystąpił...
-
Badania spękań niskotemperaturowych podbudów z AC WMS na nowobudowanej autostradzie A1 w Polsce. Część 2 - Analiza przyczyn powstania spękań nawierzchni.
PublicationW artykule przedstawiono problem niskotemperaturowych spękań poprzecznych, które powstały na nowo budowanych podbudowach z betonu asfaltowego o wysokim module sztywności AC WMS. Liczne spękania niskotemperaturowe powstały na analizowanych podbudowach AC WMS podczas okresu zimowego w 2012 r., zanim cała konstrukcja nawierzchni została ukończona. Spękania powstały zarówno na połączeniach technologicznych, jak i między nimi. Problem...
-
Investigation of low-temperature cracking in newly constructed high-modulus asphalt concrete base course of a motorway pavement
PublicationThe paper presents the issue of low-temperature transverse cracks which have developed in newly constructed base courses made of high-modulus asphalt concrete mix (HMAC). Numerous transverse cracks developed in the analysed HMAC base during the winter season before the pavement was actually completed, both at the transverse joint locations and in the areas between them. This had not happened so far on such a scale during road construction...
-
Lepkosprężyste modelowanie mieszanek mineralno-asfaltowych przy długim czasie obciążenia za pomocą krzywych wiodących i jego ograniczenia
PublicationW pierwszej części artykułu przedstawiono podstawowe informacje teoretyczne o modelowaniu mieszanek mineralno-asfaltowych z wykorzystaniem krzywych wiodących. Zaprezentowano najpowszechniej stosowane modele krzywych wiodących (symetryczne oraz niesymetryczne) oraz modele współczynników przesunięcia. Druga część przedstawia zastosowanie wybranych modeli krzywych wiodących oraz współczynników przesunięcia do opisu zachowania się...
-
Opinia techniczna dotycząca przyczyn uszkodzeń warstw asfaltowych konstrukcji nawierzchni obwodnicy Pruszcza Gdańskiego
PublicationCelem opinii technicznej jest ustalenie możliwych przyczyn uszkodzeń warstw asfaltowych konstrukcji nawierzchni Obwodnicy Pruszcza Gdańskiego (ul. Przemysłowej i ul. Nowej Przemysłowej w Pruszczu Gdańskim) i przedstawienie technologii naprawy powstałych uszkodzeń.
seen 3839 times