Search
Institute of Mechanics and Machine Design
Publications
Filters
total: 1174
displaying 1000 best results Help
Catalog Publications
Year 2019
-
A SEARCH OF AN INDUCER GEOMETRY THAT IS BENEFICIAL FOR LIFTING PARAMETERS OF A LIFTED OBJECT OF A SELECTED SHAPE
PublicationThe literature describes acoustic levitation phenomena with the utilization of air squeeze film between the vibrating inducer and the lifted object. The objective of the study is to determine the shape of the inducer with vibration characteristics that would allow the levitation of an object of the assumed geometry. In this paper, the influence of the dimension ratio of the inducer on the frequency of the first mode of vibration...
-
A three-dimensional periodic beam for vibroacoustic isolation purposes
PublicationThis paper presents results of investigations on a three-dimensional (3-D) isotropic periodic beam. The beam can represent a vibroacoustic isolator of optimised dynamic characteristics in the case of its longitudinal, flexural and torsional behaviour. The optimisation process concerned both the widths as well as the positions of particular frequency band gaps that are present in the frequency spectrum of the beam. Since the dynamic...
-
Abrasion Resistance of S235, S355, C45, AISI 304 and Hardox 500 Steels with Usage of Garnet, Corundum and Carborundum Abrasives
Publication -
Algorytmy roju w modelowaniu MES, czyli jak stado szpaków może pomóc inżynierowi
PublicationW poprzednich numerach „Pisma PG” prof. Jacek Rumiński przedstawił możliwości i perspektywy rozwoju sztucznej inteligencji (SI), zwłaszcza w kontekście notujących obecnie liczne sukcesy sztucznych sieci neuronowych. Jednak nie tylko budowa układu nerwowego jest inspiracją dla nowych metod SI. Ciekawą grupą metod są algorytmy wzorujące się na zachowaniu zwierząt, zwłaszcza na ich zdolnościach socjalnych i współpracy przy stawianiu...
-
ANALYSIS OF BONE WEDGE DIMENSIONS SELECTION METHODS IN HIGH TIBIAL OSTEOTOMY
PublicationThe article presents the analysis of methods for selecting dimensions of bone wedge for high tibial osteotomy. The existing methods are described along with the procedure. In the following paragraphs, deficiencies in the selection of bone wedge dimensions and global trends in this field have been demonstrated. Based on the numerical analysis, the problem appearing in the wrong choice of bone wedge imensions was illustrated.
-
Analysis of loading history influence on fatigue and fracture surface parameters using the method of induction trees
Publication -
Analysis of ring cracks in ceramic rolling elements using the boundary element method
PublicationCeramic materials have been increasingly used in bearing technology for over a dozen years. This is due to the characteristic properties of ceramic materials such as: high hardness, corrosion resistance, the possibility of use in aggressive chemical environments, as well as due to the lower specific weight compared to steel materials. However, the use of ceramic materials is connected with many limitations. The main disadvantages...
-
Application of decision–making parametric structures in the analysis of a compound planetary gear
Publication -
Comparison of pavement noise properties on selected road sections using different CPX measuring systems: self-powered vehicle and special test trailer
PublicationThe recently published ISO standard intended to measure the noise properties of road surfaces in a standardized method (ISO 11819-2:2017) precisely defines measurement procedure of the influence of road surface on traffic noise. According to it, two types of test vehicles may be utilized: a self-powered vehicle fitted with one or more test tyres and a trailer towed by a separate vehicle with one or more test tyres mounted on the...
-
Damage Detection in the Wind Turbine Blade Using Root Mean Square and Experimental Modal Parameters
PublicationThe paper presents results of an experimental study related to a non-destructive diagnostic technique used for preliminary determination the location and size of delamination in composite coatings of wind turbine blades. The proposed method of damage detection is based on the analysis of the ten first mode shapes of bending vibrations, which correspond to displacements of rotor blades perpendicular to the rotor plane. Modal parameters...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublicationIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Effective configuration of a double triad planar parallel manipulator for precise positioning of heavy details during their assembling process
PublicationIn the paper, dynamics analysis of a parallel manipulator is presented. It is an atypical manipulator, devoted to help in assembling of heavy industrial constructions. Few atypical properties are required: small workspace; slow velocities; high loads. Initially, a short discussion about definition of the parallel manipulators is presented, as well as the sketch of the proposed structure. In parallel, some definitions, assumptions...
-
Engineering method of tire rolling resistance evaluation
PublicationTire rolling resistance is one of the most difficult tire parameters to measure. The reason is that for modern tires the force of rolling resistance corresponds to 0.5–1% of tire load, thus measurements of very small forces must be performed in a heavily loaded system. This constitutes great problems, especially in road conditions. Laboratory measurements are easier to perform, as the environment may be better controlled, but roadwheel...
-
ESTYMACJA WSPÓŁCZYNNIKÓW SZTYWNOŚCI ZAMOCOWANIA PODATNEGO PRZEDMIOTU OBRABIANEGO NA STOLE FREZARKI
PublicationW pracy przedstawiono metodę estymacji współczynników sztywności Elementów Sprężystych (ES) modelujących zamocowanie podatnego wielkogabarytowego przedmiotu obrabianego na stole frezarki. Proponowana metoda bazuje na algorytmie optymizacji za pomocą roju cząstek (ang. Particle Swarm Optimization), który pozwala na uzyskanie dobrej zgodności (aktualizacji) modelu Metody Elementów Skończonych (MES) z modelem pochodzącym z identyfikacji...
-
Experiment-aided virtual prototyping to minimize tool-workpiece vibration during boring of large-sized structures
PublicationThe paper presents the author's method of solving the problems of vi-bration suppression during boring of large-sized workpieces by means of an in-novative method of adjusting the rotational speed of the boring bar. It consists in selecting the spindle speed in accordance with the results of the cutting process simulation. The method includes identification of the model of the finite element method of the boring bar. The Root Mean...
-
Experimental investigation into surface texture effect on journal bearings performance
PublicationThe aim of this study was to analyse the performance of journal bearings with specially created dimples on the sliding surface and operating under various conditions. The texture was created on the bearing surface that co-acted with the smooth journal; moreover, the variation of the textured surface of the journal mating with the smooth bearing was tested, and the results were compared to those obtained with the standard smooth...
-
FATIGUE TESTING MACHINES AND APPARATUS
Publication -
Fractal analysis of the bending-torsion fatigue fracture of aluminium alloy
Publication -
Fracture Surface Analysis of the EN AW-2017A-T4 Specimens with Rectangular Section
Publication -
Further development of the poroelastic road surface within the new Polish project SEPOR
PublicationRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
Heat transfer phenomena of glassy carbon foams
Publication -
Hybrid Finite Element Method Development for Offshore Structures’ Calculation with the Implementation of Industry Standards
PublicationIn the design process of offshore steel structures, it is typical to employ commercial calculation codes in which simulationand evaluation of results are performed on the basis of the available standards (e.g. API, DNV, Lloyds). The modelingand solution rely on finite element methods and cover the simulation of the structure’s properties along with the influenceof the marine environment – sea currents, wave...
-
Hybrid Finite Element Method Development for Offshore Structures’ Calculation with the Implementation of Industry Standards
PublicationIn the design process of offshore steel structures, it is typical to employ commercial calculation codes in which simulation and evaluation of results are performed on the basis of the available standards (e.g. API, DNV, Lloyds). The modeling and solution rely on finite element methods and cover the simulation of the structure’s properties along with the influence of the marine environment – sea currents, wave and wind loading,...
-
Hyperbolic heat conduction at a microscopic sliding contact with account of adhesion-deformational heat generation and wear
PublicationDifferent non-Fourier models were proposed to simulate temperatures in materials subjected to extremely fast thermal disturbances, when the speed of heat propagation should be concerned. The present study investigated temperature and heat balance at a microscopic sliding contact during a single frictional interaction based on the Cattaneo-Vernotte hyperbolic heat conduction equation. Two fundamental features of friction, namely,...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
Influence of the shoe type on the ground reaction forces
PublicationThe aim of this work was to estimate a relationship between the type of the footwear and ground reactions. Differences in medio-lateral, anterior-posterior and vertical reactions are compared for different shoe-types for male and female volunteers. Each of the participants gait was recorded in case of different shoes and without them, also stabilograms were analyzed. Results revealed differences in ground reaction forces for different...
-
Inverse heat transfer problem solution of sounding rocket using moving window optimization
PublicationAn Inverse Heat Transfer Problem is solved for a sounding rocket module given its geometry and measured temperature profile. The solution is obtained via moving window optimization, a technique for solving inverse dynamics. An analysis is performed to modify the method to avoid oscillatory behavior of the resulting heat flux profile. The method parameters are tuned in relation to characteristic phases of the flight. Results are...
-
Investigation of the thermal effects in water-lubricated journal bearings with axial grooves
PublicationWater-lubricated hydrodynamic journal bearings are frequently applied as stern tube bearings due to their advantages over other bearing types. They are environmentally friendly, can operate without sealings and in conditions of low friction losses. The most popular are bearings with open axial grooves, which require, for proper operation, forced axial flow of the lubricating water. Correctly designed and operated stern tube bearings...
-
Jaw biomechanics: Estimation of activity of muscles acting at the temporomandibular joint
PublicationThe aim of this study was to elaborate a method of estimation of activity of surface muscles acting at the temporomandibular joint of the healthy subjects by using a surface electromyography (EMG). The scope of this study involved testing chosen jaw motions (open, close, lateral deviation) and process of mastication occurring during eating food with different toughness (chewing gum, cereal and carrot) by using mixed sides, right...
-
Low Noise Poroelastic Road Pavements Based On Bituminous Binder
PublicationTire/road noise is the dominant source of traffic noise. It depends both on the tire design and on the characteristics of road pavements as well as on the vehicles’ operating conditions. Due to the fact that conventional (pneumatic) car tires have almost reached the limits of their ability to further reduce their noisiness, it is widely believed that the additional reduction of tire noise will be possible mainly through modifications...
-
Mechanical properties of the human stomach under uniaxial stress action
PublicationThe aim of this study was to estimate the range of mechanical properties of the human stomach in order to use the collected data in numerical modelling of surgical stapling during resections of the stomach. The biomedical tests were conducted in a self-developed tensile test machine. Twenty-two fresh human stomach specimens were used for the experimental study of its general strength. The specimens were obtained from morbidly obese...
-
Metal Foams as Novel Catalyst Support in Environmental Processes
Publication -
Metodologia badania zaworów hamulcowych
PublicationArtykuł opisuje metodologię statycznego i dynamicznego badania zaworów hamulcowych. Stanowisko badawcze zaprojektowano i zbudowano na Politechnice Gdańskiej jako część projektu badawczo-rozwojowego pt.: „Zaprojektowanie i zbadanie innowacyjnych podsystemów ładowarek kołowych firmy Hydro-Metal”, dofinansowanego przez PARP w ramach programu „Bon na innowacje”. Ponadto przedstawiono szczegóły konstrukcyjne i funkcje najczęściej spotykanych zaworów...
-
Minimization of vibrations during milling of flexible structures using mechatronic design techniques
PublicationThe paper presents an innovative effective method of minimizing vibrations during milling of flexible structures, using a new vibration suppression method based on a workpiece holder with adjustable support stiffness. The proposed method is rooted in mechatronic design techniques, which can become a standard procedure for optimizing the milling process.
-
Multibody models for gait analysis
PublicationThe aim of this study was to create multibody biomechanical models to analyze a normal gait of the human. Proposed models can be used to identify joint moments of the lower limbs during normal gait in the single and double support phases. Applying Newton-Euler formulation, following planar models were developed: 1) a mathematical 6DOF model describing a gait in the sagittal plane of the body for single support phase and double...
-
Optimization of the spindle speed during milling of large-sized structures with the use of technique of Experiment-Aided Virtual Prototyping
PublicationIn the paper are presented considerations concerning vibration suppression problems during milling of large-sized workpieces with the use of innovative method of matching the spindle speed of cutting tool. It depends on repeatable change of the spindle speed value as soon as the optimal vibration state of the workpiece approaches. The values of dominant “peaks” in the frequency spectra and the Root Mean Square (RMS) values of time...
-
Optymalizacja prędkości obrotowej narzędzia podczas wytaczania przedmiotów wielkogabarytowych
PublicationPrzedstawiono nową metodę wyznaczania optymalnej prędkości obrotowej narzędzia podczas wytaczania przedmiotów wielkogabarytowych, na podstawie symulacji procesu obróbki. Przeprowadzane są one dla modelu obliczeniowego wirującego narzędzia, dostrojonego do wyników testów modalnych, wraz z przyjętym modelem procesu skrawania. Ocenie podlegają wartości skuteczne (RMS) poziomu drgań w dziedzinie czasu oraz wartości dominujących amplitud...
-
Pomiary skuteczności hamowania w stacjach kontroli pojazdów
PublicationPrzeprowadzono pomiary skuteczności hamowania w warunkach różnych stacji kontroli pojazdów. Celem przedsięwzięcia było porównanie wyników z uzyskanych pomiarów. Na tej podstawie pozyskano dane umożliwiające opracowanie założeń do koncepcji metodyki badań technicznych pojazdów zabytkowych w stacjach kontroli pojazdów.
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Post-failure fracture surface analysis of notched steel specimens after bending-torsion fatigue
Publication -
Powder metallurgy of the porous Ti-13Nb-13Zr alloy of different powder grain size
PublicationThe objective of the present project was to determine the effects of powder granulation (fraction of grain size) for the Ti-13Nb-13Zr alloy, produced by powder metallurgy, on its porosity, grain cohesion, compressive strength, and Young`s modulus. Two powder fractions, 45–105 µm, and 106–250 µm were applied. The 50 mass pct of NH4HCO3 was added as a space holder. The specimens were in compaction stage uniaxially pressed at pressure...
-
Projekt aCiret odpowiedzią na wyzwania przemysłu 4.0
PublicationDruga dekada XXI w. jest początkiem nowej rewolucji przemysłowej, określanej jako przemysł 4.0. Coraz powszechniejsze systemy cyberfizyczne, internet rzeczy, obliczenia i procesy sterowane w chmurze wymagają wysoko wykwalifikowanych pracowników, uzbrojonych w ogólną i specjalistyczną wiedzę oraz doświadczenie, wykazujących się przedsiębiorczością i inicjatywą. Problem braku odpowiedniej kadry dotyka firmy z sektora przemysłowego,...
-
Rigid finite elements and multibody modeling in analyses of a robot shaped elastic/plastic deformations of a beam
PublicationDynamics analysis of a system composed of a parallel manipulator and of an elastic beam is presented in the paper. Classic 3RRR parallel manipulator is considered and used to deform the beam. Elasto-plastic deformations are investigated. Rigid-finite-elements technique is employed to deal with dynamics of the beam. A multibody structure is associated with the introduced hybrid system in order to model its dynamics. Idea of the...
-
Roboty mobilne o kinematyce wzorowanej na kinematyce węży
PublicationRoboty mobilne znajdują zastosowanie w wielu dziedzinach. W zależności od pełnionych funkcji, rodzaju i ukształtowania podłoża, po którym się poruszają oraz warunków pracy, w ich konstrukcjach wykorzystywane są różne sposoby lokomocji przy czym coraz częściej konstrukcje są wzorowane na anatomii zwierząt. Jednym z ich typów są roboty wzorowane na kinematyce ruchu węży. Jest ona odmienna od typowych rozwiązań stosowanych w rozwiązaniach...
-
Shot peening intensity effect on bending fatigue strength of S235, S355 and P460 structural steels
Publication -
Simplified Map-based Selection of Optimal Spindle Speeds When Milling Complex Structures
PublicationIn the paper a method for selecting optimal spindle speeds for complex structures during milling operations is presented. It is based on the selection of the spindle speed in accordance with a simple equation resulting from the minimisation of vibration energy, which leads to the minimisation of the work of cut-ting forces presented in previous elaborations by the authors [1]. Optimal spindle speeds are obtained for many points...
-
The delocalization of production to Poland
Publication -
The influence of inflation pressure and ambient temperature on the value of the truck tires rolling resistance
PublicationThe articlediscusses the effect of inflation pressure and the ambient temperature on the value of the rolling resistance of truck tires which directly translates into fuel consumption. For this purpose, a series of measurements was made at two ambient temperatures (at 25°C and -15°C), using different pumping pressures.
-
The influence of water and mineral oil on volumetric losses in the displacement pump for offshore and marine applications
PublicationIn this paper volumetric losses in a positive displacement pump supplied with water and mineral oil are described and compared. The experimental tests were conducted using a prototype of a satellite pump (with a non-circular tooth working mechanism). In this paper the sources of volumetric losses in this pump are characterised. On this basis, a mathematical model of these losses has been presented. The results of the calculation...
-
The Method of Finding the Optimal Spindle Speed When Milling Flexible Details
PublicationThe paper presents a new method of vibration reduction during milling of flexible details. The method consists in selecting the optimal spindle speed, based on the natural frequency of the workpiece. For this purpose, an original method was created, which is based on minimizing the work of cutting forces in the direction of the depth of cutting. The effectiveness of the method has been proved by comparing the RMS values of vibration...