Search
Filters
total: 42
Search results for: HYDRODYNAMIC BEARINGS
-
Research work on water lubricated polymer hydrodynamic bearings.
PublicationW pierwszej części artykułu w skrócie omówiono stanowisko badawcze na którym przeprowadzono eksperyment. W drugiej części opisano symulowane warunki pracy łożyska i zaprezentowano wyniki badań. Z przeprowadzonej analizy rezultatów wynika, że jest możliwe uzyskania tarcia płynnego w okrętowym łożysku wału śrubowego z polimerową panwią smarowanym wodą.
-
Klocki samopompujące w łożyskach hydrodynamicznych = Self-pumping pads in the hydrodynamic bearings
PublicationWe współpracy z firmą ALSTOM HYDRO (Szwajcaria), zespół Katedry Konstrukcji i Eksploatacji Maszyn Politechniki Gdańskiej przeprowadził symulacje przepływowe kilku rozwiązań konstrukcyjnych mających na celu zwiększenie niezawodności turbin wodnych. W artykule opisano jedno z takich rozwiązań - tak zwane łożysko z klockami samopompującymi. Głównym celem jest uzyskanie przepływu oleju w układzie smarowania łożyska hydrodynamicznego...
-
HYDRODYNAMIC THRUST BEARINGS WITH POLYMER LINING
PublicationPolymeric linings of sliding surfaces of the hydrodynamic bearings have been used successfully for over 50 years. Despite of their long history of operation and research, they have not become wide spread in industrial applications. This fact may be surprising, considering th e conclusions that have been published concerning bearing operation and design. This paper summarizes the current...
-
Large Hydrodynamic Thrust Bearings and Their Application in Hydrogenerators
PublicationLarge hydrodynamic thrust bearings are the bearings which, due to hydrodynamic lubrication, allow large axial load to be transferred from a moving part (shaft) to the stationary part via a thin layer of the lubricant (usually oil), thus providing extremely low friction and practically no wear. Hydrogenerators with vertical shafts are the most important application of large thrust bearings. Main design and scientific problems of...
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublicationThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
Experimental comparison of hydrodynamic thrust bearings with different pad surface materials
PublicationBabbitt is the material most frequently used as the pad surface material for hydrodynamic bearings operating at usual operating conditions. It shows many advantages important for safe bearing operation, as for example: low friction coefficient, corrosion resistance, fair mechanical properties and outstanding conformability. On the other hand, it is not free from disadvantages, such as limited fatigue strength or limited resistance...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublicationHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
ANALYSIS OF BEARING CLEARANCE AND WIDTH OF OIL GROOVE ON CHARACTERISTIC OF FLUID FILM IN HYDRODYNAMIC MAIN CRANKSHAFT BEARINGS
PublicationAbstract Paper represents analysis of influence of oil groove width and bearing clearance on characteristics of oil film in hydrodynamic journal main crankshaft bearing. Analysis was performed in purpose to define influence of bearing clearance and dimensions of oil groove on static characteristics and manufacturability of half shelf bearings in industrial high-volume production. Computer simulations was made using ARTbear program...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublicationMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
The experimental identification of the dynamic coefficients of two hydrodynamic journal bearings operating at constant rotational speed and under nonlinear conditions.
PublicationHydrodynamic bearings are commonly used in ship propulsion systems. Typically, they are calculated using numerical or experimental methods. This paper presents an experimental study through which it has been possible to estimate 24 dynamic coefficients of two hydrodynamic slide bearings operating under nonlinear conditions. During the investigation, bearing mass coefficients are identified by means of a newly developed algorithm....
-
EXPERIMENTAL STUDY OF DIFFERENT SUPPLY DESIGNS IN HYDRODYNAMIC THRUST BEARINGS = Badania doświadczalne różnych sposobów smarowania wzdłużnych łożysk ślizgowych
PublicationHydrodynamiczne łożyska wzdłużne charakteryzują się znacznymi stratami tarcia, które przyczyniają się do wzrostu temperatury łożyska i obniżenia jego nośności. Obecnie olej smarujący jest zazwyczaj chłodzony w zewnętrznych układach chłodzenia. Po schłodzeniu olej jest dostarczany z powrotem do korpusu łożyska, z reguły do przestrzeni między klockami łożyska. Skuteczność dostarczania schłodzonego oleju w pobliże wlotu do szczeliny...
-
The effect of the exposure-in-oil on the contact of the polymers forming sliding layers in hydrodynamic bearings. Wpływ ekspozycji w oleju na kąt zwilżania polimerów stosowanych na warstwy ślizgowe w łożyskach hydrodynamicznych.
PublicationPolimery stosowane jako warstwy ślizgowe w hydrodynamicznych łożyskach wzdłużnych to zazwyczaj tworzywa termoplastyczne charakteryzujące się relatywnie wysokimi wartościami kątów zwilżania w porównaniu z metalami. Metale, w tym również Babbitt czy inne stopy łożyskowe, cechują niskie wartości kątów zwilżania. Im niższy kąt, tym powierzchnia lepiej się zwilża. Tworzywa sztuczne wykorzystywane w węzłach tribologicznych mających zapewnić...
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie nośności...
-
Wpływ założeń modelu obliczeniowego na wyniki obliczeń hydrodynamicznych łożysk wzdłużnych = The influence of model simplifications on the predicted performance of hydrodynamic thrust bearings
PublicationPrzedstawiono porównanie wyników obliczeń hydrodynamicznych łożysk wzdłużnych otrzymanych z wykorzystaniem dwóch niezależnie opracowanych modeli obliczeniowych TEHD (termoelastohydrodynamicznych). Wykorzystane w obliczeniach programy różnią się głównie założeniami i uproszczeniami przyjętymi, zwłaszcza w odniesieniu do części przepływowej zadania. Symulacje obliczeniowe przeprowadzono stosując w przypadku obu modeli te same warunki...
-
Obliczeniowa analiza wybranych systemów dostarczania smaru w hydrodynamicznych łożyskach wzdłużnych = Computational analysis of selected supply designs in hydrodynamic thrust bearings
PublicationPrzedstawiono przykładowe wyniki obliczeniowej analizy wpływu zastosowania wybranych systemów dostarczania schłodzonego oleju do łożyska na właściwości łożyska.
-
Analiza przepływu oleju przez rowek smarowy wzdłużnego łożyska ślizgowego z wykorzystaniem komputerowej dynamiki płynów (CFD) = Analysis of the lubricant flow through the hydrodynamic thrust bearings groove with the use of computational fluid dynamic
PublicationSmarowanie zanurzeniowe jest tradycyjnym sposobem smarowania wzdłużnych łożysk ślizgowych. Jednak rozwiązanie to wykazuje umiarkowaną skuteczność w zapewnieniu optymalnie niskich temperatur w filmie smarowym a ponadto jest przyczyną strat mocy związanych z mieszaniem oleju w obudowie łożyska, co jest szczególnie widoczne w łożyskach szybkoobrotowych. Obecnie wymagania stawiane nowym konstrukcjom łożysk ślizgowych to zwiększanie...
-
Michał Wasilczuk prof. dr hab. inż.
PeopleMichał Wasilczuk received his M.Sc. (1986), Ph.D. (1994) and D.Sc. (2004) from the Gdansk University of Technology. In 2016 was nominated Professor Currently he is a Full Professor and Head of the Department of Machine Design and Automotive Engineering at the Faculty of Mechanical Engineers at GUT Bearing systems and tribology are the main fields of his scientific and engineering interest - starting from the Ph.D. devoted to...
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublicationWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Large hydrodynamic thrust bearing: Comparison of the calculations and measurements
PublicationHydrodynamic thrust bearings, used to carry axial loads in heavily loaded shafts of water power plants hydro turbines, can reach outer diameters even exceeding 5 m. In such large objects scale effect could be observed. According to this, allowable bearing specific load assuring safe operation of the bearings has to be decreased, which increases thrust bearing dimensions. This effect is caused by excessive thermal deflections of...
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublicationWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
Investigation of the thermal effects in water-lubricated journal bearings with axial grooves
PublicationWater-lubricated hydrodynamic journal bearings are frequently applied as stern tube bearings due to their advantages over other bearing types. They are environmentally friendly, can operate without sealings and in conditions of low friction losses. The most popular are bearings with open axial grooves, which require, for proper operation, forced axial flow of the lubricating water. Correctly designed and operated stern tube bearings...
-
Water-Lubricated Journal Bearings Marine Applications, Design, and Operational Problems and Solutions
PublicationWater-Lubricated Journal Bearings: Marine Applications, Design, and Operational Problems and Solutions provides cutting-edge design solutions, common problems and methods for avoiding them, and material selection considerations for the use of water-lubricated journal bearings in marine environments. These bearings have many advantages, including the absence of the potential for oil contamination. They are also sensitive, and their...
-
Application of the Optimization Methods to the Search of Marine Propulsion Shafting Global Equilibrium in Running Condition
PublicationFull film hydrodynamic lubrication of marine propulsion shafting journal bearings in running condition is discussed. Considerable computational difficulties in non-linear determining the quasi-static equilibrium of the shafting are highlighted. The approach using two optimization methods (the particle swarm method and the interior point method) in combination with the specially developed relaxation technique is proposed to overcome...
-
OPERATING CONDITIONS OF SLIDE BEARINGS OF MILLS USED IN KGHM POLSKA MIEDŹ S.A.
PublicationThe paper contains the results from a tec hnical analysis of the conditions of the operation of hydrodynamic bearings supporting the drums of ore processing mills at KGHM Polska Mied ź S.A. A theoretical analysis was performed on the grounds of onsite examination and measurem ents of principal dimensions of the bearings of interest. The computer simulation covered the characteristics of the oil film in the bearings...
-
Study of the Influence of Heat Convection Coefficient on Predicted Performance of a Large Tilting-Pad Thrust Bearing
PublicationPart of the heat generated by the shearing of the lubricating film during operation of a hydrodynamic bearing is transferred to the bearing components. In the case of the pad, which is usually fully submerged in the lubricating oil, heat is further transferred at the pad free walls to the oil by convection. This mechanism causes a thermal gradient in a pad and, consequently, its thermal deflection. In large hydrodynamic thrust...
-
Compliance tests of the polymer layers used as hydrodynamic bearing coatings
PublicationOperational experience and scientific investigations results showed that polymer lined hydrodynamic bearings can withstand more severe operating conditions compared than white metal bearings. PTFE and PEEK-based coatings are the most frequently used as Babbitt alternatives. Both polymers differ significantly from the each other in material properties. According to catalogue data compression modulus of PTFE, it is about an order...
-
Experimental study on the feasibility of alternative materials for tilting pad thrust bearings operating in transition to mixed friction
PublicationIn hydrodynamic bearings traditional bearing alloys: Babbitts and bronzes are most frequently utilized. Polymer sliding layers are sometimes applied as a valuable alternative. Hard diamond-like carbon (DLC) coatings, which are also considered for certain applications may show some advantages, as well. Although material selection is of secondary importance in a full film lubrication regime it becomes important in mixed friction...
-
Structural properties of foil bearings: a closed-form solution validated with finite element analysis
PublicationFluid film thickness in a compliant foil bearing is greatly influenced by the deflection of the bearing structure. Therefore, in order to properly model performance of a foil bearing, it is mandatory that the deflection of the compliant bearing structure due to the generated hydrodynamic pressure is determined accurately. This article proposes an easy-to-use two-dimensional model, which takes into account detailed geometry of the...
-
Should we seek further improvement of fluid film bearings - what for and how?
PublicationFluid film bearings have been extensively used in the industry because of their unbeatable durability and extremely low friction coefficient. Large bearings supporting shafts of huge and important rotating machines constitute a special group of fluid film bearings since the reliability of crucial systems, like for example electro-energetic system, rely on their trouble-free operation. Large thrust bearings, apart from enormous...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublicationWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
Intelligent microbearing project with memory of stress-strain history
PublicationTaking into account the increasing need of intelligent micro-bearing with memory, this paper presents the optimization, simulation and practical application of operating parameters(load carrying capacity, friction forces, friction coefficient, wear), simulation for hydrodynamic HDD micro-bearing with curvilinear nano-grooved journal profile. One of the reason of such journal profile is that this journal profile contributes to the...
-
HYDROSTATIC THRUST BEARING WITH REDUCED POWER LOSSES
PublicationIn many cases in rotating machinery, axial load is carried by tilting pad thrust bearings which have been developed since the beginning of 20th century. For high reliability and simplicity, most commonly the bearings are bath lubricated. In the times of sustainable development, however, minimization of friction losses becomes an important criterion for machinery assessment, and a strategic goal of their development. Performed calculations,...
-
Experimental research on marine oil-lubricated stern tube bearing
PublicationBearings of propeller shafts are very crucial elements of the propulsion system of each of the ships. The safety of shipping depends on their durability and reliability. The new legal restrictions mean that today we are looking for environmentally friendly solutions. That is why water-lubricated bearings are becoming more and more popular. So, will oil-lubricated shaft bearings belong to the past? The bearing with a white metal...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublicationThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Wielkogabarytowe hydrodynamiczne łożyska wzdłużne
PublicationW monografii przedstawiono problemy konstrukcyjne i badawcze hydrodynamicznych łożysk wzdłużnych o dużych średnicach. Łożyska takie stanowią istotne i niezwykle odpowiedzialne podzespoły hydrogeneratorów elektrowni wodnych. Z uwagi na rozmiary (średnice przekraczają niekiedy 5 metrów) i złożoność zjawisk łożyska te wymagają specjalnej postaci konstrukcyjnej, a ich dokładna analiza obliczeniowa przysparza wiele problemów. Dodatkowo...
-
Prospects of Decreasing Power Losses in a Hydrostatic Thrust Bearing
PublicationIn numerous machines, axial load is carried by tilting pad thrust bearings known since the beginning of 20th century. These bearings are commonly bath lubricated, which is simple, does not require any additional pumps, and, due to this, such systems are highly reliable. In a contemporary technology, however, minimization of friction losses became an important goal of machinery improvement. Calculations based on elementary rules...
-
New Generation of Water lubricated Foil bearing - Numerical Models and Experimental Verification
PublicationIn the paper a new idea of foil water lubricated bearing and methodology of hydrodynamic characteristics calculations is presented. To assesses the theoretical characteristics of these bearings two different computer models were built. First is structural model coupled with fluid model. It takes into account: fluid flow in the deformed fluid gap, specific design of bearing support and friction in bearing support. The second is...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublicationHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing
PublicationIn the present study, investigation of the effect of manufacturing errors on the performance of large tilting pad thrust bearings has been performed, following a CFD-based Thermohydrodynamic analysis of a single pad. A 3D model has been generated, including the pad, the lubricant film and the corresponding part of the collar. The pad has been assumed to be deformed about the pivot point, due to thrust loading. Manufacturing errors...
-
Field Tests on Hydrodynamic and Hybrid Operation of a Bidirectional Thrust Bearing of a Pump-Turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Due to the bidirectional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Field tests on hydrodynamic and hybrid operation of a bi-directional thrust bearing of a pump-turbine
PublicationIn vertical shaft pump turbines operating in pumped storage power plants an important role is played by a thrust bearing. Because of bi-directional character of operation, thrust bearing tilting pads have to be supported symmetrically, which is known to be unfavourable from the point of view of their performance. Large thrust bearings have to be carefully designed so as to minimise excessive thermo-elastic pad deformations. The...
-
Research and applications of active bearings: A state-of-the-art review
PublicationControllable/active bearings are mainly associated with active magnetic bearings (AMBs), whereas active bearing control is also found in many types of bearings, e.g. fluid, gas and hybrid bearings. The article presents a review of the literature describing the structure and results of studies of active bearings. Active control brings a number of benefits resulting in the fact that their use as a support for rotors becomes increasingly...