Filters
total: 28
Search results for: lifting surface
-
Blade Section Prpfile Array Lifting Surface Design Method for Marine Screw Propeller Blade
PublicationThe lifting surface model is widely used in screw propeller design and analysis applications. It serves as a reliable tool for determination of the propeller blade mean line and pitch distribution. The main idea of this application was to determine the blade shape that would satisfy the kinematic boundary condition on its surface with the prescribed bound circulation distribution over it. In this paper a simplified lifting surface...
-
Experimental Verification of the CFD Model of the Squeeze Film Lifting Effect
PublicationAbstract: The presented study shows the results of the research into the squeeze film levitation phenomena. The system introduced in the investigation is composed of a vibrating surface, air squeeze film, and the surface of the body freely suspended over the film. The use of the CFD (Computational Fluid Dynamics) model used in the system allows us to determine the steady state, periodic behavior of the air film (described by Navier–Stokes,...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublicationHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
A SEARCH OF AN INDUCER GEOMETRY THAT IS BENEFICIAL FOR LIFTING PARAMETERS OF A LIFTED OBJECT OF A SELECTED SHAPE
PublicationThe literature describes acoustic levitation phenomena with the utilization of air squeeze film between the vibrating inducer and the lifted object. The objective of the study is to determine the shape of the inducer with vibration characteristics that would allow the levitation of an object of the assumed geometry. In this paper, the influence of the dimension ratio of the inducer on the frequency of the first mode of vibration...
-
Effect of the Presence of the Lifting Pocket on The THD Performance of a Large Tilting-Pad Thrust Bearing
PublicationIn this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of Itaipu power plant. B3earing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket
-
Parametric method applicable in calculating breakout force and time for lifting axisymmetric objects from seabed.
PublicationThe issue of calculating parameters for lifting objects of axisymmetric shapes from the seabed is studied. The article presents the results of numerical simulation examination of the equation formulated by Foda for the force needed to extricate the object from the seabed depending on soil and water parameters, extrication speed, and object diameter. The simulations were performed within the range of parameters characteristic for...
-
Running characteristics of aerodynamic bearing with self-lifting capability at low rotational speed
PublicationAn aerodynamic journal bearing that is capable of self-generating squeeze-film pressure is presented and its dynamic characteristics investigated numerically and experimentally. A numerical method based on a time marching static model was applied to assess the orbit trajectory path of the rotor upon a perturbation. Experimental results were obtained to validate the effect of the self- generated squeeze-film pressure on the stability...
-
Parametric method applicable in assessing breakout force and time for lifting slender bodies from seabed
PublicationThe article presents a parametric method applicable in assessing the suction force of a slender body to the seabed, and prognosing the body extrication time. Along with the body weight in water, the information on the suction force is essential for assessing the force needed to lift the object from the seabed. Based on the Foda theory and the resulting integral equation, which relates the maximum suction force with basic parameters...
-
Pre-swirl energy saving device in marine application
PublicationThis paper covers topics of energy saving device (ESD) with application to marine propulsors. The form of ESD, considered in this paper, consists of fixed lifting foils mounted in front of the screw propeller (the pre-swirl stator/guide vanes). An algorithm for designing propulsion systems, consisting of guide vanes and screw propeller, is presented. The proposed method relies on hybrid lifting line (guide vanes)-lifting surface...
-
Conditions of Iranian international trade in terms of lifting the sanctions: A case study of Polish-Iranian trade perspectives
PublicationThe main aim of the paper is to identify the areas and determine the feasibility of trade between Polish and Iranian companies in relation to historical and cultural conditions. The authors describe the complexity of the issue of foreign trade, the determinants of relations between Poland and the Islamic Republic of Iran, and the Iranian economy – its features, strengths and weaknesses, and consequences of the recent UN, EU, and...
-
Measurement Of The Dynamics Of The Sheave Block Of Shipyard Crane With 1000 T Lifting Capacity For Verification Of The Laboratory Stand
Publication -
The Motion Analysis of Attacus Atlas Rigid Wing
PublicationThe remarkable aerodynamic efficiency of flapping insect wings has fascinated researchers for many years. Butterfly wings are distinguished by a much larger lifting surface, and thus, a different style of flapping flight. The considerations described in the article are an introduction to a fully flexible analysis of the wing in motion. The study of the rigid wing gives the basic knowledge necessary in the further process. The yaw,...
-
EXPERIMENTAL AND NUMERICAL VALIDATION OF THE IMPROVED VORTEX METHOD APPLIED TO CP745 MARINE PROPELLER MODEL
PublicationThe article presents a numerical analysis of the CP745 marine propeller model by means of the improved vortex method and CFD simulations. Both numerical approaches are validated experimentally by comparing with open water characteristics of the propeller. The introduced modification of the vortex method couples the lifting surface approach for the propeller blades and the boundary element method for the hub. What is more, a...
-
Experimental and Computational Analysis of the Ship Propeller in Open Water Conditions for Inclined Flow
PublicationThe paper presents the results of computational analyses simulating the open water tests of ship propeller in inclined flow. The results of computations are compared with the results of corresponding experimental analyses carried out in the towing tank of Ship Design and Research Centre (CTO S.A.). The object of the research was the model propeller identified as CP469. The aim of the study was to validate the results of numerical...
-
Fully Separated Flow Control Using DBD Plasma Actuators Located at the Leading Edge of an Airfoil
PublicationIn the framework of the PLASMAERO European project, experiments were conducted to investigate the authority of surface DBD plasma actuators to alter a fully separated flow around an airfoil in order to improve its aerodynamic performances in its natural stall regime. In this paper, unsteady excitation control is more specifically investigated. The key control parameter studied here is the burst frequency which periodically imposes...
-
Ring thruster - a preliminary optimisation study
PublicationThe ring thruster is a new type of propeller, for which there is no experimental data to verify analytical design calculations. A significant feature of the ring thruster is the absence of a shaft. Propeller blades are mounted to the ring rotating inside the housing, which has the shape of a nozzle. For this reason the ring thruster is closest, with respect to both the construction and principle of operation, to the Kort nozzle...
-
Top 10 Iran Export Partners in 2011
Open Research DataLifting of Iranian sanctions could lead to a rapid improvement in the economic situation of Iran. This will not only remove the barriers of international transactions, but also enable the investments of foreign entities on the territory of Iran, increasing the competitiveness of operators, including in the key mining sector.
-
Top 10 Iran Import Goods in 2011
Open Research DataThe following dataset shows the volume of trade of the European Union countries with Iran. One can observe a significant drop in both imports and exports (the year 2012 meant tightening of sanctions, which clearly limited the import of Iranian products to the EU). After lifting the sanctions it is expected to substantially increase the level of trade...
-
Total Goods: EU Trade flows and balance with Iran, 2005-2015 (in millions of USD).
Open Research DataThe following dataset shows the volume of trade of the European Union countries with Iran. One can observe a significant drop in both imports and exports (the year 2012 meant tightening of sanctions, which clearly limited the import of Iranian products to the EU). After lifting the sanctions it is expected to substantially increase the level of trade...
-
Energetic model of hydraulic system of refuse collection vehicle based on simulation and experimental data
PublicationThis paper presents an energetic model of hydraulic system of a refuse collection vehicle. First, benefits resulting from implementation of an energetic model in the industry and operation of a Refuse Collection Vehicle are briefly explained. Then, components of the energy consumption in hydraulic circuits of compactor and lifting device are described and combined into a comprehensive model that can be evaluated using basic measurement...