Repozytorium Open Access
Filtry
wszystkich: 14002
wyświetlamy 1000 najlepszych wyników Pomoc
Katalog Publikacji
Rok 2023
-
Improved methods for stator end winding leakage inductance calculation
PublikacjaCalculating the stator end-winding leakage inductance, taking into account the rotor, is difficult due to the irregular shape of the end-winding. The end-winding leakage may distribute at the end of the active part and the fringing flux of the air gap. The fringing flux belongs to the main flux but goes into the end-winding region. Then, not all the magnetic flux occurring in the end region is the end-winding leakage flux. The...
-
IMPLEMENTING THE QUALITY ASSURANCE SYSTEM AND ASSURING HEALTH SAFETY IN THE LIGHT OF INCREASING BREAD QUALITY
PublikacjaThe article presents rules, requirements, and norms for quality management and health safety assurance systems among small and medium bakeries. This group of businesses does not have the obligation of implementing or certifying specific systems. They are, however, implemented in order to increase the quality of the bread or reach a better market position. Also, the results of a 2022 study of 53 bakeries’ implementation of individual...
-
Implementation of IMS/NGN Transport Stratum Based on the SDN Concept
PublikacjaThe paper presents the development and verification of software and a testbed aiming to demonstrate the ability of two telecommunication network concepts—Next Generation Network (NGN) and Software-Defined Networking (SDN)—to cooperate. The proposed architecture includes components of the IP Multimedia Subsystem (IMS) in its service stratum and of the SDN (controller and programmable switches) in its transport stratum, providing...
-
Implementation of an Adaptive Method for Changing the Frequency Division of the Counter Clock Signal in a Frequency-to-Code Converter
PublikacjaProcessing physical quantities into an indirect signal is a standard method of transferring information about the measured quantity to the master system, which analyzes the data obtained from the acquisition system. The intermediate signal is very often the voltage, but another transmission medium can be the frequency of the output signal of the “physical quantity-to-frequency” converter. The article presents the implementation...
-
Impact of thermal backfill parameters on current-carrying capacity of power cables installed in the ground
PublikacjaProper design of power installations with the participation of power cables buried in homogeneous and thermally well-conductive ground does not constitute a major problem. The situation changes when the ground is non-homogeneous and thermally low-conductive. In such a situation, a thermal backfill near the cables is commonly used. The optimization of thermal backfill parameters to achieve the highest possible current-carrying capacity...
-
Impact of temperature on optical sensing in biology based on investigation of SARS‐CoV ‐2
PublikacjaIn this paper, we present an investigation of the influence of the temperature on the sensing of biological samples. We used biofunctionalized microsphere-based fiber-optic sensor to detect immunoglobulin G attached to the sensor head at temperatures relevant in biological research: 5°C, 25°C, and 55°C. The construction of the sensor allowed us to perform measurements in the small amount of solution. The results of our experiment...
-
Impact of strontium non-stoichiometry of SrxTi0.3Fe0.7O3-δ on structural, electrical, and electrochemical properties for potential oxygen electrode of intermediate temperature solid oxide cells
PublikacjaThis work presents the results of a comprehensive study on the impact of the A-site non-stoichiometry of SrxTi0.3Fe0.7O3-δ (x = 0.90, 0.95, 1.00, 1.05) ceramics on their physicochemical properties. The materials were fabricated by the conventional solid-state reaction method and their structure was determined by X-ray diffractometry, X-ray photoelectron spectroscopy and electron microscopy. Their sintering and thermal expansion...
-
Impact of steel grade on a ship colliding with an offshore wind turbine monopile supporting structure
PublikacjaOffshore wind power is experiencing rapid development around the world. The number of installations and their size is growing. Thousands of monopile support structures with diameters of 10 m and weights of 2000 tons will be installed in the coming years. Offshore wind power installations, often located close to the shore and shipping routes, pose a new challenge to ship safety. The study analyses the damages from an accidental...
-
Impact of Climate Change on Water Sources and River‐Floodplain Mixing in the Natural Wetland Floodplain of Biebrza River
PublikacjaThe origins of river and floodplain waters (groundwater, rainfall, and snowmelt) and their extent during overbank flow events strongly impact ecological processes such as denitrification and vegetation development. However, the long-term sensitivity of floodplain water signatures to climate change remains elusive. We examined how the integrated hydrological model HydroGeoSphere and the Hydraulic Mixing-Cell method could help us...
-
Impact of blending with polystyrene on the microstructural and electrochemical properties of SiOC ceramic
PublikacjaIn this work, we present the electrochemical behavior and microstructural analysis of silicon oxycarbide (SiOC) ceramics influenced by an addition of polystyrene (PS). Polymer-derived ceramics were obtained by pyrolysis (1000°C, Ar atmosphere) of different polysiloxanes prepared by sol–gel synthesis. This method is very effective to obtain desired composition of final ceramic. Two alkoxysilanes phenylthriethoxysilane and diphenyldimethoxysilane...
-
Impact of AlphaFold on structure prediction of protein complexes: The CASP15‐CAPRI experiment
PublikacjaWe present the results for CAPRI Round 54, the 5th joint CASP-CAPRI protein assembly prediction challenge. The Round offered 37 targets, including 14 homodimers, 3 homo-trimers, 13 heterodimers including 3 antibody–antigen complexes, and 7 large assemblies. On average 70 CASP and CAPRI predictor groups, including more than 20 automatics servers, submitted models for each target. A total of 21 941 models submitted by these groups...
-
Impact assessment culture in the European Union. Time for something new?
PublikacjaCurrent approaches and cultures for the economic evaluations of environmental and health policies may suffer from excessive reliance on a standard neoclassic economic toolbox that neglects alternative perspectives. This may prematurely limit the spectrum of available policy options. Here we show how the inclusion of neglected currents of thought such as non-Ricardian economics, bioeconomics and a set of qualitative-quantitative...
-
Hydrophobic (deep) eutectic solvents (HDESs) as extractants for removal of pollutants from water and wastewater – A review
PublikacjaDeep eutectic solvents (DESs) are a new generation of solvents that attracted increasing attention in diverse applications. In last years, growing number of studies on hydrophobic (deep) eutectic solvents (HDESs) as an alternative extractants for various chemicals from aqueous environments have been reported. This article provides an overview on the usage of HDESs in liquid–liquid extraction (LLE) of different pollutants from water...
-
Hydraulic fracturing process in rocks – small-scale simulations with a novel fully coupled DEM/CFD-based thermo-hydro-mechanical approach
PublikacjaW artykule przedstawiono dwuwymiarową (2D) symulację numeryczną szczelinowania hydraulicznego w małej skali przeprowadzoną w próbkach skał posiadających pojedynczą szczelinę wtryskową. Wykorzystano unikalny model termo-hydro-mechaniczny (THM) w skali porów oparty na DEM/CFD do symulacji dwufazowego laminarnego przepływu płynu (wody i gazu) z przenoszeniem ciepła w nienasyconych materiałach porowatych o niskiej porowatości. Korzystając...
-
Hybrydowa koncepcja łagodzenia stromości zmian napięcia du/dt dla wielopoziomowych przekształtników kaskadowych SiC
PublikacjaW referacie zaproponowano nową hybrydową koncepcję łagodzenia stromości zmian napięcia du/dt w wielopoziomowych przekształtnikach kaskadowych SiC. Proponoana koncepcja polega na wykorzystaniu nietłumionego filtra du/dt, podatnego na rezonans oraz zastosowaniu w algorytmie sterowania PWM dodatkowych impulsów sterujących tranzystorami SiC MOSFET, wymuszających rezonansowe przełączanie napięcia na wyjściu filtra. Efekt zmniejszenia...
-
Human Resource Management Digitalisation in Multidisciplinary Ship Design Companies
PublikacjaThe digitalisation in the ship design sector is currently applied to the design process itself and is well defined, partially standardised and practically implemented by both independent design companies and the design departments of shipyards. The situation is similar in other sectors of engineering. However, the requirements for the digitalisation of other processes in design and engineering companies have not previously been...
-
How to evaluate methods used in chemical laboratories in terms of the total chemical risk? – a ChlorTox Scale
PublikacjaReliable assessment of the health and environmental risk associated with the use of chemicals is critical to ob- jectively evaluate the greenness and whiteness of an analytical method. An objective and useful way of risk assessment should take into account all the relevant properties of used substances, their actual amounts needed for application of the method, and quantify the assessment result using a standardized unit. This...
-
How the Depths of the Danish Straits Shape Gdańsk's Port and City Spatial Development
PublikacjaThe depths of the Danish Straits limit the drafts of ships entering the Baltic Sea. The largest ships calling the Baltic in a laden condition are called Baltimax. The article presents how the dredging works carried out in the Danish Straits in the 1970s enabled the development of the Port of Gdańsk and consequently also influenced the city, being a residential base for employees of the new port and shipyards. The analysed case...
-
How pesticides affect neonates? - Exposure, health implications and determination of metabolites
PublikacjaThis review covers key information related to the effects of pesticides on fetal and child health. All humans are exposed to environmental toxicants, however child's health, due to their high vulnerability, should be of special concern. They are continuously exposed to environmental xenobiotics including a wide variety of pesticides, and other pollutants. These compounds can enter the child's body through various routes, both during...
-
How do responsible universities perceive their social engagement? In search of signs of Creating Shared Value by the University
PublikacjaObjectives: University social responsibility still lacks legitimisation and is perceived as a burden that hinders academics from doing research and teaching. Creating Shared Value by the University may serve as a tool to motivate universities to engage in initiatives for society, as this is beneficial for both parties. Yet, some researchers perceive the creation of economic value as inappropriate for academia. Thus, it was interesting...
-
How do personality traits influence Open Government Data (OGD) adoption and usage? Investigating the indirect and moderating effects
PublikacjaOpen Government Data (OGD) research has focused for a long on the adoption and usage from the perspectives of users across different contexts. The underlying rationale for this specific focus is that OGD initiatives are undertaken to further citizen engagement with OGD for value generation and innovation purposes. Conceding that usage propensity is different across individuals, it is important to understand the influence of personality...
-
How acidic amino acid residues facilitate DNA target site selection
PublikacjaDespite the negative charge of the DNA backbone, acidic residues (Asp/Glu) commonly participate in the base readout, with a strong preference for cytosine. In fact, in the solved DNA/protein structures, cytosine is recognized almost exclusively by Asp/Glu through a direct hydrogen bond, while at the same time, adenine, regardless of its amino group, shows no propensity for Asp/Glu. Here, we analyzed the contribution of Asp/Glu...
-
Homogeneous nucleation rate of methane hydrate formation under experimental conditions from seeding simulations
PublikacjaIn this work, we shall estimate via computer simulations the homogeneous nucleation rate for the methane hydrate at 400 bars for a supercooling of about 35 K. The TIP4P/ICE model and a Lennard-Jones center were used for water and methane, respectively. To estimate the nucleation rate, the seeding technique was employed. Clusters of the methane hydrate of different sizes were inserted into the aqueous phase of a two-phase gas–liquid...
-
Historia kształtowania polskiej terminologii elektrotechnicznej
PublikacjaPrzedstawiono prace nad kształtowaniem języka w zakresie elektrotechniki. Prace te zaczynają od początków wykorzystania elektryczności pod koniec XIX wieku, kończą na dostosowaniu do norm europejskich i tworzeniu słownika internetowego. Omówiono wydarzenia związane z organizacją słowotwórstwa oraz najważniejsze publikacji zawierające słownictwo obowiązujące w danym okresie.
-
High-Temperature Tensile Behaviour of GTAW Joints of P92 Steel and Alloy 617 for Two Different Fillers
PublikacjaThis study explores the high-temperature (HT) tensile rupture characteristics of a dissimilar gas-tungsten-arc-welded (GTAW) joint between P92 steel and Alloy 617, fabricated using ER62SB9 and ERNiCrCoMo-1 fillers. The high-temperature tensile tests were performed at elevated temperatures of 550 ◦C and 650 ◦C. An optical microscope (OM) and a field emission scanning electron microscope (FESEM) were utilized to characterize the...
-
High-temperature Corrosion of ~ 30 Pct Porous FeCr Stainless Steels in Air: Long-Term Evaluation Up to Breakaway
PublikacjaIn this work, a long-term (up to 6000 hours) corrosion evaluation of three porous (~ 30 pct of initial porosity) ferritic iron-chromium alloys with different Cr contents (20, 22, and 27 wt pct of Cr) was carried out at 600 C, 700 C, 800 C, and 900 C in air. Mass gain measurements and SEM analyses revealed that at temperatures above 600 C, all alloys exhibit breakaway corrosion, whereas at 600 C, none of the alloys were heavily...
-
High-Resolution, Broad-Range Detection Setup for Polarimetric Optical Fiber Sensors
PublikacjaA common-path polarization interferometer using a Wollaston prism and an area detector for the measurement of retardation or optical path difference is presented. Employing a moderate-resolution 1280 by 1024 pixel monochrome camera, it offers a measurement range of approximately 780 radians at 830 nm and 1350 radians at 515 nm while maintaining a high measurement resolution. Retardation introduced by a zero-order waveplate or a...
-
Highly stable CsFAPbIBr perovskite solar cells with dominant bulk recombination at real operating temperatures
PublikacjaMixed-cation mixed-halide perovskite solar cells have been characterized in DC at different temperatures (from −20 °C up to 50 °C) and the time evolution of the device efficiency has been assessed using different degradation protocols (indoors and outdoors). The completely planar p–i–n structure is ITO/CuNiOx/PTAA/CsFAPbIBr/PCBM/PEI/Ag. Pristine current–voltage characteristics barely show hysteresis, at any temperature. Open circuit...
-
Highly Occupied Surface States at Deuterium-Grown Boron-Doped Diamond Interfaces for Efficient Photoelectrochemistry
PublikacjaPolycrystalline boron-doped diamond is a promising material for high-power aqueous electrochemical applications in bioanalytics, catalysis, and energy storage. The chemical vapor deposition (CVD) process of diamond forma-tion and doping is totally diversified by using high kinetic energies of deu-terium substituting habitually applied hydrogen. The high concentration of deuterium in plasma induces atomic arrangements and steric...
-
High-Efficacy Global Optimization of Antenna Structures by Means of Simplex-Based Predictors
PublikacjaDesign of modern antenna systems has become highly dependent on computational tools, especially full-wave electromagnetic (EM) simulation models. EM analysis is capable of yielding accurate representation of antenna characteristics at the expense of considerable evaluation time. Consequently, execution of simulation-driven design procedures (optimization, statistical analysis, multi-criterial design) is severely hindered by the...
-
Heterojunction of (P, S) co-doped g-C3N4 and 2D TiO2 for improved carbamazepine and acetaminophen photocatalytic degradation
PublikacjaNovel photocatalysts of phosphorus and sulfur co-doped graphitic carbon nitride incorporated in 2D TiO2 structure were successfully fabricated and applied for solar-driven degradation of emerging pollutants from the group of pharmaceuticals not susceptible to biodegradation. The hybrid photocatalysts with different loadings of (P, S)-doped g-C3N4 were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR),...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublikacjaUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Healthy financial system of local government on the example of Poland
Publikacjahealthy local government financial system lays the foundation for the ability of local government units (LGUs) to carry out public tasks at the current qualitative and quantitative level and to meet their obligations in the short and long term. A healthy financial system of local government is a system that is adequate, stable, unified, consistent, transparent, diversified, counter-cyclical, guarantees the financial independence...
-
HEALTH MONITORING OF A COMPRESSION IGNITION ENGINE FED WITH DIFFERENT LOW-SULPHUR MARINE FUELS BY ENDOSCOPIC IMAGE PROCESSING AND ANALYSIS
PublikacjaThis article characterises the methodology for the endoscopic testing of a laboratory diesel engine used for testing marine fuels. The ‘Shadow’ measurement method used in the XLG3 type EVEREST digital endoscope, for quantitative and qualitative identification of detected surface defects, was approximated. Representative endoscopic images of the elements limiting the working space of the research engine are demonstrated, having...
-
HCI-Based Wireless System for Measuring the Concentration of Mining Machinery and Equipment Operators
PublikacjaMaintaining stable and reliable working conditions is a matter of vital importance for various companies, especially those involving heavy machinery. Due to human exhaustion, as well as unpredicted hazards and dangerous situations, the personnel has to take actions and wisely plan each move. This paper presents a human–computer interaction (HCI)-based system that uses a concentration level measurement function to increase the safety...
-
H2O˙+ and OH+ reactivity versus furan: experimental low energy absolute cross sections for modeling radiation damage
PublikacjaRadiotherapy is one of the most widespread and efficient strategies to fight malignant tumors. Despite its broad application, the mechanisms of radiation-DNA interaction are still under investigation. Theoretical models to predict the effects of a particular delivered dose are still in their infancy due to the difficulty of simulating a real cell environment, as well as the inclusion of a large variety of secondary processes. This...
-
GUIDED WAVES IN SHIP STRUCTURAL HEALTH MONITORING – A FEASIBILITY STUDY
PublikacjaShips and offshore structures operate in a severe corrosion degradation environment and face difficulty in providing long- lasting corrosion protection. The Classification Societies recommend regular thickness measurements leading to structural component replacements, to ensure structural integrity during service life. The measurements are usually performed using ultrasonic thickness gauges and such an approach requires multiple...
-
Ground lemon and stevia leaves as renewable functional fillers with antioxidant activity for high-density polyethylene composites
PublikacjaThe development of new sustainable material solutions in the processing of thermoplastic polymers concerns both the application of biopolymers and the use of valorized plant derivatives as fillers and modifiers of petrochemical polymers. Herein, the possibility of using unprocessed raw parts of two commonly used in the food industry leaves, i.e., lemon (LL) and stevia (ST), as active and functional fillers for high-density polyethylene...
-
Green, simple analytical method for total biogenic amines content determination in wine using spectrophotometry
PublikacjaA simple, green and equitable procedure for total biogenic amines (BAs) content determination was developed. The scientific novelty lies in the use of commercially available S 0378 dye, the reaction of which with BAs results in a colour change of the solution. Sample preparation and analysis were simplified to make the method suitable for routine analyses even in resource-scarce settings. The optimization of the method was carried...
-
Green sample preparation 2023
Publikacjabrak
-
Green and Sustainable Membranes: A review
PublikacjaMembranes are ubiquitous tools for modern water treatment technology that critically eliminate hazardous materials such as organic, inorganic, heavy metals, and biomedical pollutants. Nowadays, nano-membranes are of particular interest for myriad applications such as water treatment, desalination, ion exchange, ion concentration control, and several kinds of biomedical applications. However, this state-of-the-art technology suffers...
-
Great Resignation and Quiet Quitting as Post-pandemic Dangers to Knowledge Management
PublikacjaPurpose: COVID-19 pandemic aftermaths include the emergence of new tendencies, such as the Quiet Quitting, and continuation of trends such as the Great Resignation, both of which have multiple knowledge-related impacts on individual, organizational and even national level. The aim of this paper is to show the mechanisms behind the Quiet Quitting and the Great Resignation from individual and organizational perspectives. Understanding...
-
Graphene Production and Biomedical Applications: A Review
PublikacjaGraphene is a two-dimensional nanomaterial composed of carbon atoms with sp2 hybrid orbitals. Both graphene and graphene-based composite have gained broad interest among researchers because of their outstanding physiochemical, mechanical, and biological properties. Graphene production techniques are divided into top-down and bottom-up synthesis methods, of which chemical vapor deposition (CVD) is the most popular. The biomedical...
-
Graph Neural Networks and Structural Information on Ionic Liquids: A Cheminformatics Study on Molecular Physicochemical Property Prediction
PublikacjaIonic liquids (ILs) provide a promising solution in many industrial applications, such as solvents, absorbents, electrolytes, catalysts, lubricants, and many others. However, due to the enormous variety of their structures, uncovering or designing those with optimal attributes requires expensive and exhaustive simulations and experiments. For these reasons, searching for an efficient theoretical tool for finding the relationship...
-
Globalized Knowledge-Based Simulation-Driven Antenna Miniaturization Using Domain-Confined Surrogates and Dimensionality Reduction
PublikacjaDesign of contemporary antenna systems encounters multifold challenges, one of which is a limited size. Compact antennas are indispensable for the new fields of application such as inter-net of things or 5G/6G mobile communication. Still, miniaturization generally undermines elec-trical and field performance. When attempted through numerical optimization, it turns into a constrained problem with costly constraints requiring electromagnetic...
-
Global value chains and wages under different wage setting mechanisms
PublikacjaThis study examines whether, and how, differences in wage bargaining schemes shape the relationship between global value chains (GVCs) and the wages of workers while considering both GVC participation and position in GVC. Our dataset is derived from the European Structure of Earnings Survey (SES), containing employee–employer data from 18 European countries, merged with sectoral data from the World Input-Output Database (WIOD)....
-
Global energy transition: From the main determinants to economic challenges regions
PublikacjaDynamic global energy transition has been accelerating for the last decade. Interestingly, the energy transition is multidimensional and concerns both the dimensions of technique/ technology and the economic, social, institu-tional, and legal spheres (Shuguang et al., 2022; Tzeremes et al., 2022; Ram-zan et al., 2022; Tzeremes et al., 2022). The literature also points to the signif-icant impact of the digitization of the global...
-
Global Complex Roots and Poles Finding Algorithm in C × R Domain
PublikacjaAn algorithm to find the roots and poles of a complex function depending on two arguments (one complex and one real) is proposed. Such problems are common in many fields of science for instance in electromagnetism, acoustics, stability analyses, spectroscopy, optics, and elementary particle physics. The proposed technique belongs to the class of global algorithms, gives a full picture of solutions in a fixed region ⊂ C × R and...
-
GIS-based hydrodynamic modeling for urban flood mitigation in fast-growing regions: a case study of Erbil, Kurdistan Region of Iraq
PublikacjaFloods threaten urban infrastructure, especially in residential neighborhoods and fast-growing regions. Flood hydrodynamic modeling helps identify flood-prone locations and improve mitigation plans' resilience. Urban floods pose special issues due to changing land cover and a lack of raw data. Using a GIS-based modeling interface, input files for the hydrodynamic model were developed. The physical basin's properties were identified...
-
Giant Reed (Arundo donax L.) Fiber Extraction and Characterization for Its Use in Polymer Composites
PublikacjaThis work describes an extraction method for giant reed fibers from stems and leaves based on chemical soaking and crushing through a rolling mill. Obtained fibers, together with the shredded plant (stems + leaves), are characterized in terms of chemical composition, thermal stability, morphology, and crystallinity. Mechanical properties of fibers have also been assessed (single fiber tensile tests). The results show that the proposed...