Publikacje
Filtry
wszystkich: 801
Katalog Publikacji
Rok 2024
-
Analysis of Roughness, the Material Removal Rate, and the Acoustic Emission Signal Obtained in Flat Grinding Processes
PublikacjaIn this work, the analysis of the acoustic emission (AE) signal in grinding processes is addressed. The proposed analysis method decomposes the acoustic signal into three frequency ranges. The total energy of each range is determined, as well as the highest frequency. Different grinding experiments were carried out, according to a full factorial design of experiments (DOE), in which feed speed, depth of cut, and transversal step...
Rok 2023
-
Multi-objective optimization of tool wear, surface roughness, and material removal rate in finishing honing processes using adaptive neural fuzzy inference systems
PublikacjaHoning processes are usually employed to manufacture combustion engine cylinders and hydraulic cylinders. A crosshatch pattern is obtained that favors the oil flow. In this paper, Adaptive Neural Fuzzy Inference System (ANFIS) models were obtained for tool wear, average roughness Ra, cylindricity and material removal rate in finish honing processes. In addition, multi-objective optimization with the desirability function method...
-
Modeling of Surface Roughness in Honing Processes by UsingFuzzy Artificial Neural Networks
PublikacjaHoning processes are abrasive machining processes which are commonly employed to improve the surface of manufactured parts such as hydraulic or combustion engine cylinders. These processes can be employed to obtain a cross-hatched pattern on the internal surfaces of cylinders. In this present study, fuzzy artificial neural networks are employed for modeling surface roughness parameters obtained in finishing honing operations. As...
-
Influence of Honing Parameters on the Quality of the Machined Parts and Innovations in Honing Processes
PublikacjaThe article presents a literature review dealing with the effect of the honing parameters on the quality of the machined parts, as well as with the recent innovations in honing processes. First, an overview about the honing and the plateau-honing processes is presented, considering the main parameters that can be varied during machining. Then, the influence of the honing parameters on surface finish, shape deviation and material...
Rok 2021
-
Wpływ sposobu suszenia na wiązkość i naprężenia tnące przy przecinaniu wybranych gatunków drewna
PublikacjaW rozprawie doktorskiej przedstawiono wpływ sposobów suszenia na wiązkość i naprężenia tnące w strefie skrawania, które zgodnie ze współczesną mechaniką pękania można uznać za energetyczne wskaźniki skrawalności. Badania zostały przeprowadzone dla próbek z drewna sosnowego (Pinus sylvestris L.) i bukowego (Fagus silvatica L.) suszonego czterema sposobami. Trzy z nich, to najczęściej wykorzystywane w przemyśle, suszenie w sposób...
-
Opinia na temat celowości oraz zakresu rzeczowego remontu wytaczarko-frezarki płytowej typu FLF16/CNC. Ekspertyza techniczna opracowana na zlecenie ENEROMONTAŻ-PÓŁNOC GDYNIA S.A.
PublikacjaOpracowana Opinia Jednostki Naukowej dotyczyła ciężkiej wytaczarko-frezarki płytowej typu FLF16/CNC ze sterowaniem CNC. Na podstawie przeprowadzonego w miejscu użytkowania tej obrabiarki audytu, dokonano oceny obecnego stanu maszyny oraz przeanalizowano przyczyny awarii, które zdarzały się w okresie jej eksploatacji. Zakres analizy przyczyn problemów eksploatacyjnych i stanów awaryjnych obejmował: - awarie zespołu elektrowrzeciona...
-
Opinia na temat celowości oraz zakresu rzeczowego remontu tokarki karuzelowej FKD-60/80. Ekspertyza techniczna opracowana na zlecenie ENEROMONTAŻ-PÓŁNOC GDYNIA S.A.
PublikacjaOpracowana Opinia Jednostki Naukowej dotyczyła ciężkiej tokarki karuzelowej typu FKD-60/80 ze sterowaniem CNC. Na podstawie przeprowadzonego w miejscu użytkowania tej obrabiarki audytu, dokonano oceny obecnego stanu maszyny oraz przeanalizowano przyczyny awarii, które zdarzały się w okresie jej eksploatacji. Zakres analizy przyczyn stanów awaryjnych obejmował: - awarie zespołu elektrowrzeciona oraz układów hydraulicznych zawartych...
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 2/2
PublikacjaThe process of conversion of wind kinetic energy into electricity in innovative wind power plant emits practically no harmful substances into the environment. However, the production stage of its components requires a lot of energy and materials. The biggest problem during production plan-ning process of an innovative wind power plant is selection of materials and technologies and, consequently, the waste generated at this stage....
-
Manufacturing and Recycling Impact on Environmental Life Cycle Assessment of Innovative Wind Power Plant Part 1/2
PublikacjaWind power plants are considered as ecologically-clean source of energy. However, manufacturing processes cannot be treated that way. Manufacturing processes consume huge amount of electrical and thermal energy and significant amount of materials, e.g. steel, polymers, oils and lubricants. All of the above could be potentially harmful for environment. There are not many works and publications regarding life-cycle analysis of wind...
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublikacjaThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
Experimental research of the effect of face milling strategy on the flatness deviations
PublikacjaIn this paper the dependencies between face milling strategy of EN AW6082-T6 aluminum alloy samples, with difference thicknesses (6, 8, and 12 mm) and two cold rolling directions, and flatness deviations were presented. Three strategies of milling included different proportions of material removed from both sides of the plates. This approach allowed to control the proportions of residual surface stresses on both sides of the specimens,...
-
Analiza gładzenia otworów walcowych przy zmiennych warunkach kinematycznych
PublikacjaW pracy zweryfikowano wpływ parametrów obróbki na przebieg procesu gładzenia i stwierdzono, że metodą umożliwiającą uzyskanie zarówno dobrej jakości powierzchni jak i niższej o 35,2% temperatury przedmiotu gładzonego oraz mniejszej o 12,77% odchyłki walcowości (w porównaniu do gładzenia tradycyjnego) jest gładzenie ze zmienną kinematyką. Zmienny...
-
A pilot study to assess manufacturing processes using selected point measures of vibroacoustic signals generated on a multitasking machine
PublikacjaThe article presents the method for the evaluation of selected manufacturing processes using the analysis of vibration and sound signals. This method is based on the use of sensors installed outside the machining zone, allowing to be used quickly and reliably in real production conditions. The article contains a developed measurement methodology based on the specific location of microphones and vibration transducers mounted on...
Rok 2020
-
Wpływ rozmieszczenia elementów w separatorach na warunki kinematyczne docierania jednotarczowego
PublikacjaPrzedstawiono wyniki analiz kinematyki docierania elementów płaskich na docierarkach jednotarczowych o standardowym układzie wykonawczym. Określono wpływ rozmieszczenia elementów obrabianych w separatorach na zmienność prędkości docierania.
-
Wpływ rozmieszczenia elementów w separatorach na warunki kinematyczne docierania jednotarczowego
PublikacjaW rozdziale monografii naukowej przedstawiono wyniki analiz kinematyki docierania elementów płaskich na docierarkach jednotarczowych o standardowym układzie wykonawczym. Określono wpływ rozmieszczenia elementów obrabianych w separatorach na zmienność prędkości docierania. W przeprowadzonej symulacji wykorzystano wybrane modele docierarek firmy Kemet, analizując obróbkę dwóch elementów o zróżnicowanych wymiarach gabarytowych i zarysie...
-
Wear of electroplated diamond tools in lap-grinding of Al2O3 ceramic materials
PublikacjaCurrent development of modern products, together with ever-increasing demands for their operation and usage, necessitate the search for new processing methods. Abrasive machining is widely used in many industrial areas, especially for processing difficult-to-machine materials such as advanced ceramics. Grinding with lapping kinematics, also called lap-grinding, is still one of the innovative methods of abrasive processing being...
-
Unlocking creativity with new technologies
PublikacjaArtificial intelligence, augmented and virtual reality, Internet of Things and digital twins are just a few concepts related to the fourth industrial revolution that is happening right before our eyes. The key question asked by managers in the aerosol sector recently is: what does all this new technology mean to me?
-
Tool Wear Prediction in Single-Sided Lapping Process
PublikacjaSingle-sided lapping is one of the most effective planarization technologies. The process has relatively complex kinematics and it is determined by a number of inputs parameters. It has been noted that prediction of the tool wear during the process is critical for product quality control. To determine the profile wear of the lapping plate, a computer model which simulates abrasive grains trajectories was developed in MATLAB. Moreover,...
-
Thickness accuracy of sash gang sawing
PublikacjaThin lamellae, corresponding to the layer components of structural glued members, i.e. 2-ply or 3-ply glued parquet, can be manufactured in re-sawing operations of kiln-dried wood blocks. These must be prepared with high dimensional accuracy and adequate surface quality following specific technical requirements for lamellae thickness variations, especially in the upper layers of the glued composite parquet. The accuracy of oak...
-
Theoretical and Actual Feed Per Tooth During Wood Sawing on an Optimizing Cross-Cut Saw
PublikacjaThe work presents the geometries of circular saw teeth, whose task is to divide the cross-cut of the cutting layer. For efficient machining on a cross-cut saw with high feed speed values (about 1 ms−1) maximal theoretical feeds per tooth are determined. These values were compared with the actual values determined during transverse cutting of pine wood on a special test stands in industrial conditions. In the experiment the rotational...