Wyszukiwarka
Wydział Inżynierii Mechanicznej i Okrętownictwa
Publikacje
Filtry
wszystkich: 2602
wyświetlamy 1000 najlepszych wyników Pomoc
Katalog Publikacji
Rok 2024
-
The Effect of Steaming Beech, Birch and Maple Woods on Qualitative Indicators of the Surface
PublikacjaThis work presents the effect of steaming beech, birch and maple woods on the resulting quality of the milled wood surface. The steaming process of the studied woods results in a targeted change in the color of the wood, which changes from the original light white-gray color to fine reddishbrown to dark brown color shades that are more or less saturated depending on the temperature of the saturated water steam. The color changes...
-
The experimental and numerical investigation of fracture behaviour in PMMA notched specimens under biaxial loading conditions – Tension with torsion
PublikacjaThis paper presents the results of experimental fracture test of flat PMMA specimens under biaxial loading condition tension with torsion (proportional). The specimens were made in two thicknesses: 5 and 15 mm and were weakened with V-type edge notches with different root radii: 0.5; 2 and 10 mm. Thanks to the ARAMIS 3D 4 M non-contact vision system, measurement of the elongation and twist angle were recorded. During experimental...
-
The Impact of Drying Conditions on the Surface Color Changes of Pine Wood
PublikacjaThe article presents the impact of drying process and selected parameters on the color changes on the surface of pine wood (Pinus sylvestris L.). Three predetermined process conditions (modes), mild, normal, and intensive, were investigated. The experiments were conducted using a semi-industrial scale dryer designed at the Gdańsk University of Technology with a loading capacity of 0.55 m3. The drying process was applied to pine...
-
The Influence of Global Corrosion Degradation on Localized Damage Detection Using Guided Waves
PublikacjaThis paper presents the results of a numerical analysis of the influence of corrosion degradation of metal plates on the wave propagation phenomenon. There are several different corrosion types, but general and pitting corrosion are the most common. General corrosion is more or less uniformly distributed over the entire exposed surface of the metal while pitting corrosion takes the form of localized cracks. Because the general...
-
The Influence of Impact Velocity on Stresses and Failure of S355j2 Steel Under Slurry Erosion Conditions
Publikacja -
The Influence of Impact Velocity on Stresses and Failure of S355j2 Steel Under Slurry Erosion Conditions
PublikacjaThe purpose of this work was to determine the essence of the influence of the impact velocity (5, 7, and 9 m/s) on Hertzian stresses and the erosion mechanism of ferritic-pearlitic S355J2 steel. The investigations were carried out using a slurry pot tester. S355J2 steel showed a strong sensitivity to changes in impact velocity. A significant increase in erosion rate was observed at a velocity of 9 m/s. This increase was 5-fold...
-
The Smith-Watson-Topper parameter and fracture surface topography relationship for additively manufactured 18Ni300 steel subjected to uniaxial variable-amplitude loading
PublikacjaIn this paper, the association between Smith-Watson-Topper (SWT) parameter and fracture surface topography is studied in additively manufactured maraging steel exposed to variable-amplitude fatigue loading. The post-failure fracture surfaces were examined using a non-contact 3D surface topography measuring system and the entire fracture surface method. The focal point is on the correspondence between fatigue characteristics, articulate...
-
The study on the appearance of deformation defects in the yacht lamination process using an AI algorithm and expert knowledge
PublikacjaThis article describes the application of the A-priori algorithm for defining the rule-based relationships between individual defects caused during the lamination process, affecting the deformation defect of the yacht shell. The data from 542 yachts were collected and evaluated. For the proper development of the algorithm, a technological process of the yacht lamination supported by expert decisions was described. The laminating...
-
The use of accumulation elements with lumped parameters to model the operation of heat exchange installations under randomly changing temperatures
PublikacjaAt the design stage of heat exchange installation used for gas conversion it is required to test the stability of the installation operation for the expected variable heat loads. For this purpose, a numerical model of the installation can be used. The paper presents an original concept of modelling the operation of heat exchange installations for randomly changing temperatures. Accumulation elements with lumped parameters were...
-
The Use of Cluster Analysis to Assess the Wear Resistance of Cermet Coatings Sprayed by High Velocity Oxy-Fuel on Magnesium Alloy Substrate
PublikacjaCermet coatings are one of the best surface protection of machine elements against wear. On the other hand, the most universal and economically justified method of applying such coatings is high velocity oxy-fuel (HVOF) spraying. This method makes it possible to produce coatings characterized by compact structure, low porosity and very good adhesion to the substrate. All these fundamental properties contribute to the high wear...
-
Therapeutic biomaterials – application in neurology and cardiology
PublikacjaBiomaterials are of interest in most medical fields. It's hard to imagine life without them. And due to the ever-increasing demand, scientists are developing new materials. Diseases of the nervous and cardiovascular systems are still a big problem, which are associated with a limited ability to regenerate brain or heart tissues. Therefore, this review discusses the advancement in biomaterial engineering for the treatment of neurological...
-
Timed rolling and rising tests in Duchenne muscular dystrophy ambulant boys: a feasibility study
PublikacjaBACKGROUND: Functional activities are extensively used in motor assessments of patients with Duchenne muscular dystrophy. The role of timed items has been reported as an early prognostic factor for disease progression. However, there are two functional activities that are not widely assessed in clinical practice among Duchenne muscular dystrophy patients: rolling and bed rising. This study aimed to investigate whether the 360-degree...
-
Time-dependent relaxation dynamics of remanent strain in textured PMN–PZ–PT and PMN–PIN–PT piezoceramics
PublikacjaCrystallographically textured lead-based piezoceramics, particularly P (Mg1/3Nb2/3) O3–Pb ZrO3–PbTi O3 (PMN–PZ PT) and Pb(M1/3Nb2/3)O3–Pb(In1/2Nb1/2)O3–PbTiO3 (PMN–PIN–PT), play a pivotal role in electromechanical applications due to their enhanced field-induced strain responses. However, challenges in precision positioning arise from heightened remanent strain (Sr) caused by embedded templates in the textured grains impacting...
-
Towards an analysis framework for operational risk coupling mode: A case from MASS navigating in restricted waters
PublikacjaMaritime Autonomous Surface Ships (MASSs) constitute highly interconnected and tightly coupled multistate systems. Incorporating the coupling effects of both interactions and dependencies is centrally important to ensure navigation safety of MASSs. This paper proposes a framework for examining the coupling effects in the operational modes (OM) of MASSs. Failure Modes (FMs) of MASSs related to interactions with the environment and...
-
Towards hand grip force assessment by using EMG estimators
PublikacjaThe purpose of this study was to propose a method to assess individual regression (calibration) curves to establish a relationship between an isometric grip force and surface electromyography (EMG) estimator. In this study 18 healthy volunteers (12 male (23.0 ± 2.0 years) and 6 female (23.2 ± 0.7 years)) had been examined. Ten EMG estimators (mean absolute value, root mean square, entropy, energy, turns per second, mean of zero...
-
Treatment of Odontogenic Maxillary Sinusitis with the Use of Growth Factors in Advanced Platelet-Rich Fibrin for Immediate Closure of Oro-Antral Communication: A Case Report
PublikacjaChronic odontogenic maxillary sinusitis (COMS), a prolonged inflammation of the maxillary sinus lasting over 12 weeks, is often a result of periapical lesions, marginal periodontitis, and complications like oro-antral communication (OAC) and fistula (OAF). OAC, commonly emerging post-teeth extraction in the lateral maxilla, lacks documented treatments using advanced platelet-rich fibrin (A-PRF). This study evaluates A-PRF’s efficacy...
-
Treatment of Oroantral Communication and Fistulas with the Use of Blood-Derived Platelet-Rich Preparations Rich in Growth Factors: A Systematic Review
PublikacjaThe formation of an oroantral communication (OAC) or fistula (OAF) is a rare complication resulting from the presence of processes in the lateral parts of the maxilla or for iatrogenic reasons. The most common causes of OAC or OAF are tooth extraction with periapical lesions. The aims of this systematic review were to assess the use of platelet-derived preparations rich in growth factors in the treatment of OAC or OAF, to determine...
-
Uniwersalne uchwyty obróbkowe wykorzystujące siły magnetyczne
PublikacjaPrzedstawiono współczesne konstrukcje uniwersalnych uchwytów przedmiotowych wykorzystujące do zamocowania przedmiotów obrabianych siły magnetyczne. Analizowano uchwyty magnetyczne i elektromagnetyczne w technologia obróbki wiórowej i ściernej oraz w technikach spawalniczych.
-
Walther H. Nernst - noblista z Wąbrzeźna
PublikacjaPrzedstawiono życiorys i osiągnięcia naukowe prof. Walthera Hermanna Nernsta, urodzonego 25 czerwca 1864 r. w Wąbrzeźnie, laureata Nagrody Nobla z dziedziny chemii z roku 1921. W. Nernst jest autorem m.in. III zasady termodynamiki oraz konstruktorem tzw. lampy Nernsta. Była to jedna z pierwszych lamp elektrycznych, oświetlająca wieżę Eiffla i pawilon niemiecki na Światowej Wystawie w Paryżu w 1890 r. W roku 1914 zostaje honorowym...
-
Wind Speed Probabilistic Forecast Based Wind Turbine Selection and Siting for Urban Environment
PublikacjaWind energy being a free source of energy is becoming popular over the past decades and is being studied extensively. Integration of wind turbines is now being expanded to urban and offshore settings in contrast to the conventional wind farms in relatively open areas. The direct installation of wind turbines poses a potential risk, as it may result in financial losses in scenarios characterized by inadequate wind resource availability....
-
Window frame integrable air recuperation minichannel/minigap heat exchanger
PublikacjaThis article describes an evaluation of mini heat exchangers operation as a decentralized mechanical ventilation system with recuperative heat recovery that can be integrated into the window frame. The relatively small yet efficient air recuperation system allows for retrofitting existing buildings by reducing the overall energy consumption and thus the CO2 emissions. The proposed design, unlike existing systems, is easy to scale...
-
Wpływ dawkowania pasty ściernej na intensywność docierania próbek płaskich
PublikacjaPrzedstawiono wyniki badań intensywności docierania próbek płaskich ze stopu aluminium, brązu aluminiowego i żeliwa sferoidalnego na docierarce jednotarczowej. Analizowano wpływ okresowego dawkowania elektrokorundowej pasty ściernej na wydajność obróbki w funkcji czasu, w zależności od położenia próbek w separatorach oraz liczby próbek docieranych jednocześnie i wywieranego nacisku jednostkowego.
-
Wpływ parametrów strugi paliwa wtryskiwanego do cylindra silnika okrętowego na początkową fazę rozpylania
PublikacjaPrzedmiotem rozprawy jest analiza procesu wtrysku oleju napędowego do cylindra silnika okrętowego z zapłonem samoczynnym i bezpośrednim wtryskiem paliwa. Analiza tego zagadnienia została przeprowadzona w aspekcie wpływu makro parametrów strugi na początkową fazę rozpylania oleju napędowego. Celem niniejszej pracy jest określenie wpływu współczynnika L/D (długość otworu/średnica) otworu wylotowego wtryskiwacza na zmianę charakterystyki...
-
WPŁYW SKŁADU ANODY NA WYDAJNOŚĆ I STABILNOŚĆ TLENKOWYCH OGNIW PALIWOWYCH NIO+YSZ/YSZ/LACOFEO3-Δ
PublikacjaBadano wpływ proporcji składników anody na mikrostrukturę, widma impedancyjne i charakterystyki prądowo napięciowe testowych ogniw paliwowych z elektrolitem stałym na bazie tlenku cyrkonu stabilizowanego tlenkiem itru (YSZ), anodą NiO+YSZ i katodą LaCoFeO3-δ. Pomiary przeprowadzono dla różnej zawartości pary wodnej, ciśnienia parcjalnego wodoru, a także po starzeniu pod obciążeniem 300 mA/cm2. Najlepszą wydajność i stabilność...
-
Wpływ wysokiej osteotomii piszczelowej na mechanikę stawu kolanowego
PublikacjaW rozprawie podjęto próbę weryfikacji wpływu zabiegu chirurgicznego wysokiej osteotomii piszczelowej na mechanikę stawu kolanowego. Po wykonanym przeglądzie literatury, postawiono trzy hipotezy, które poddano weryfikacji na drodze badań numerycznych. Otrzymane wyniki zwalidowano poprzez badania nacisków powierzchniowych występujących w stawach kolanowych świni domowej, prowadzonych na maszynie do jednoosiowego ściskania. Praca...
-
Wpływ zawartości grafitu na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit osadzonych na stopie AW-7075 metodą redukcji chemicznej.
PublikacjaPrzedstawiono wpływ obecności grafitu jako fazy dyspersyjnej na właściwości mechaniczne warstw hybrydowych Ni-P/Si3N4/grafit, które osadzono metodą redukcji chemicznej na stopie glinu AW-7075. Wykonano badania morfologii powierzchni warstw metodą mikroskopii świetlnej i skaningowej. Dalszą część pracy stanowiły badania mechaniczne, czyli pomiary mikrotwardości warstw oraz ich adhezji do aluminiowego podłoża, a także analizy wpływu...
-
Wytwarzanie i modyfikacja powierzchni porowatych struktur tytanowych przeznaczonych na implanty
PublikacjaCelem pracy było wytworzenie stopu Ti-13Nb-13Zr z wykorzystaniem technologii selektywnego topienia laserowego (SLM) oraz jego biofunkcjonalizacja za pomocą utleniania mikrołukowego (MAO), a następnie określenie wpływu parametrów procesowych na właściwości otrzymanych materiałów pod kątem ich zastosowania na implanty. Oceniono wpływ napięcia, natężenia i czasu procesu MAO przeprowadzanego w elektrolicie zawierającym wapń i fosfor...
Rok 2023
-
A brief note on entire fracture surface topography parameters for 18Ni300 maraging steel produced by LB-PBF after LCF
PublikacjaThe concept of entire fracture surface investigation is helpful in explaining fatigue phenomena. In this paper, this method has been applied for 18Ni300 maraging steel using a 3D measurement system. Before post-mortem analysis, the specimens produced by laser beam powder bed fusion (LB-PBF) were tested under low-cycle fatigue (LCF) for eight strain amplitudes in the interval 0.3% to 1.0%. The attention was placed on the relationship...
-
A Computational Analysis of the Aerodynamic and Aeromechanical Behavior of a Thermo-Well for Steam Temperature Measurement in a Steam Turbine
PublikacjaThe goal of the paper is twofold: firstly, it presents computational fluid dynamics analysis for finding maximum unsteady flow forces (and their frequencies) acting on a thermo-well for measuring steam temperature in a steam turbine control stage and secondly, it presents computational solid dynamics analysis of possibility of entry into resonance of the thermowell structure. There have been analyzed two cases of flow with changing...
-
A framework estimating the minimum sample size and margin of error for maritime quantitative risk analysis
PublikacjaThe average accident frequency is essential for quantitative risk analysis and is conventionally estimated from accident statistics. This paper has systematically synthesised the knowledge on statistical errors and offered the missing instructions, a framework, for determining the minimum sample size and the margin of error (MOE) when calculating the average accident frequency from an accident database at hand. We have applied...
-
A hybrid approach to optimization of radial inflow turbine with principal component analysis
PublikacjaEnergy conversion efficiency is one of the most important features of power systems as it greatly influences the economic balance. The efficiency can be increased in many ways. One of them is to optimize individual components of the power plant. In most Organic Rankine Cycle (ORC) systems the power is created in the turbine and these systems can benefit from effective turbine optimization. The paper presents the use of two kinds...
-
A new finite element with variable Young's modulus
PublikacjaThe Finite Element Method (FEM) is a numerical technique that is well-established in the field of engineering. However, in biological sciences, it is justtaking its first steps. Bone tissue is an example of biological material which isexposed to high loads in its natural environment. Practically every movementof the body results in changing stress levels in the bone. Nature copes with thisvery well but when human intervention is...
-
A novel hybrid adaptive framework for support vector machine-based reliability analysis: A comparative study
PublikacjaThis study presents an innovative hybrid Adaptive Support Vector Machine - Monte Carlo Simulation (ASVM-MCS) framework for reliability analysis in complex engineering structures. These structures often involve highly nonlinear implicit functions, making traditional gradient-based first or second order reliability algorithms and Monte Carlo Simulation (MCS) time-consuming. The application of surrogate models has proven effective...
-
A Numerical Study on Baseline-Free Damage Detection Using Frequency Steerable Acoustic Transducers
PublikacjaIn structural health monitoring (SHM) a considerable amount of damage detection algorithms based on guided waves (GW) have been developed. Most of them rely on extensive transducer networks, besides preliminary reference measurements of the structures. This originated a growing demand for hardware simplification and cost reduction of the wave-based SHM methods, driving the conception of new solutions enabling both: the reduction...
-
A Review: Applications of the Spectral Finite Element Method
PublikacjaThe Spectral Finite Element Technique (SFEM) has Several Applications in the Sciences, Engineering, and Mathematics, which will be Covered in this Review Article. The Spectral Finite Element Method (SFEM) is a Variant of the Traditional Finite Element Method FEM that Makes use of Higher Order Basis Functions (FEM). One of the most Fundamental Numerical Techniques Employed in the Numerical Simulation is the SFEM, which Outperforms...
-
A review of phase change materials and heat enhancement methodologies
PublikacjaPhase change materials (PCMs) are an efficient alternative to store and release heat at a specific range of temperature. Here PCMs and heat enhancement methodologies for PCM storage are reviewed. A short overview of PCMs and their applications is presented in addition to the progress during the last 10 years. Heat enhancement techniques, that is, extended surfaces, multiple and composite PCMs, and encapsulation techniques, are...
-
Advanced numerical modelling for predicting residual compressive strength of corroded stiffened plates
PublikacjaAn advanced methodology for predicting the residual compressive strength of corroded stiffened plates is developed here using the non-linear finite element method. The non-uniform loss of a plate thickness is accounted for on a macro-scale. In contrast, mechanical properties are changed using the constitutive model to reflect the corrosion degradation impact on a micro-scale. Three different stiffened plate thicknesses are considered,...
-
An Integrated Approach to an Assessment of Bottlenecks for Navigation on Riverine Waterways
PublikacjaWater transport, both sea and inland, is the cheapest, least invasive, and safest option for non-standard loads; hence, it is important to increase the percentage share of inland waterway transport on the rivers of Central and Eastern Europe. Transporting cargo is particularly difficult on shallow waterways because rivers overloaded with sediment determine the vertical parameters on inland waterways. A ship’s safe manoeuvrability...
-
An Intelligent Approach to Short-Term Wind Power Prediction Using Deep Neural Networks
PublikacjaIn this paper, an intelligent approach to the Short-Term Wind Power Prediction (STWPP) problem is considered, with the use of various types of Deep Neural Networks (DNNs). The impact of the prediction time horizon length on accuracy, and the influence of temperature on prediction effectiveness have been analyzed. Three types of DNNs have been implemented and tested, including: CNN (Convolutional Neural Networks), GRU (Gated Recurrent...
-
Analiza gniazda docierarek dwutarczowych do płaszczyzn - studium przypadku.
PublikacjaPrzedstawiono analizę gniazda trzech docierarek dwutarczowych do płaszczyzn. Analizowano przypadki obróbki pierścieni stalowych i krążków z ceramiki technicznej. Badano czasy główne docierania oraz składowe czasów pomocniczych w analizowanych operacjach obróbki wstępnej, dokładnej i bardzo dokładnej.
-
Analiza informacyjności diagnostycznej temperatury spalin wylotowych okrętowego tłokowego silnika spalinowego
PublikacjaW rozprawie doktorskiej zaproponowano metodykę oceny stanu technicznego silnika okrętowego w eksploatacji na podstawie pomiarów szybkozmiennej temperatury spalin wylotowych w miejscu pomiaru standardowego. Metoda ta pozwoliłaby identyfikować znane i rozpoznawalne stany niezdatności eksploatacyjnej elementów konstrukcyjnych silnika okrętowego o ograniczonej podatności kontrolnej. Rozpatrywano następujące układy funkcjonalne silnika:...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublikacjaThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Analysis of surface roughness of chemically impregnated Scots pine processed using frame-sawing machine
PublikacjaThe objective of this work was to evaluate the effect of the impregnation process of pine wood (Pinus sylvestris L.) on roughness parameters of the surface processed on a frame sawing. The samples weredried and impregnated using a commercial procedure by a local company. The touch method withthe use of measuring stylus (pin) was employed to determine of surface roughness of the samplesconsidering parameters, namely, arithmetical...
-
Analysis of the Environmental Impact of the Hull Construction of a Small Vessel Based on LCA
PublikacjaIn recent years, issues related to the impact of human activity on the natural environment have become pressing, and the challenge of global warming necessitates immediate action. To support environmental protection efforts, it has become imperative to adopt a broader perspective when evaluating various products and systems. A valuable tool for such assessments is a life cycle assessment (LCA), which enables a comprehensive analysis...
-
Analysis of the Possibilities of Applying 3D Print Methods for the Needs of Ship-Building Industry
PublikacjaArticle presents the analysis of applying additive and hybrid manufacturing methods and its impact on dynamic stiffness of prepared samples. Dynamic analysis of the handle bracket specimens consisted in plotting the resonance curves and using these curves to estimate the dynamic stiffness of elements produced with additive manufacturing technology. Authors focused especially on 3D print in Fused Deposiotion Modeling/Fused Filament...
-
Analysis of the structure of the atomized fuel spray with marine diesel engine injector in the early stage of injection
PublikacjaThis paper presents the results of the experimental research of the atomized fuel spray with the marine diesel engine injector in the constant volume chamber. The specificity of the phenomena occurring in the marine engine cylinder was the reason to use the optical visualisation method in the studies – the Mie scattering technique. This work presents an analysis of the influence of different geometry of outlet orifice and opening...
-
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublikacjaThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Antimicrobial and Antiproliferative Coatings for Stents in Veterinary Medicine—State of the Art and Perspectives
PublikacjaMicrobial colonization in veterinary stents poses a significant and concerning issue in veterinary medicine. Over time, these pathogens, particularly bacteria, can colonize the stent surfaces, leading to various complications. Two weeks following the stent insertion procedure, the colonization becomes observable, with the aggressiveness of bacterial growth directly correlating with the duration of stent placement. Such microbial...
-
Application of Feed Forward Neural Networks for Modeling of Heat Transfer Coefficient During Flow Condensation for Low and High Values of Saturation Temperatur
PublikacjaMost of the literature models for condensation heat transfer prediction are based on specific experimental parameters and are not general in nature for applications to fluids and non-experimental thermodynamic conditions. Nearly all correlations are created to predict data in normal HVAC conditions below 40°C. High temperature heat pumps operate at much higher parameters. This paper aims to create a general model for the calculation...
-
Application of unmanned USV surface and AUV underwater maritime platforms for the monitoring of offshore structures at sea
PublikacjaThe operation of offshore structures at sea requires the implementation of advanced systems for their permanent monitoring. There is a set of novel technologies that could be implemented to deliver a higher level of effective and safe operation of these systems. A possible novel solution may be the application of a new maritime unmanned (USV) surface and underwater vehicles/platforms (AUV). Application of such vehicles/platforms...