Wyszukiwarka
ISSN:
Dyscypliny:
- architektura i urbanistyka (Dziedzina nauk inżynieryjno-technicznych)
- inżynieria biomedyczna (Dziedzina nauk inżynieryjno-technicznych)
- inżynieria lądowa, geodezja i transport (Dziedzina nauk inżynieryjno-technicznych)
- inżynieria mechaniczna (Dziedzina nauk inżynieryjno-technicznych)
- inżynieria środowiska, górnictwo i energetyka (Dziedzina nauk inżynieryjno-technicznych)
- nauki chemiczne (Dziedzina nauk ścisłych i przyrodniczych)
Punkty Ministerialne: Pomoc
| Rok | Punkty | Lista |
|---|---|---|
| Rok 2024 | 70 | Ministerialna lista czasopism punktowanych 2024 |
| Rok | Punkty | Lista |
|---|---|---|
| 2024 | 70 | Ministerialna lista czasopism punktowanych 2024 |
| 2023 | 70 | Lista ministerialna czasopism punktowanych 2023 |
| 2022 | 70 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2021 | 70 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2020 | 70 | Lista ministerialna czasopism punktowanych (2019-2022) |
| 2019 | 70 | Lista ministerialna czasopism punktowanych (2019-2022) |
Model czasopisma:
Punkty CiteScore:
| Rok | Punkty |
|---|---|
| Rok 2023 | 8.6 |
| Rok | Punkty |
|---|---|
| 2023 | 8.6 |
| 2022 | 7.2 |
| 2021 | 5.2 |
| 2020 | 5.9 |
| 2019 | 4.6 |
| 2018 | 4.2 |
| 2017 | 4.7 |
| 2016 | 3.6 |
| 2015 | 2 |
| 2014 | 0.7 |
| 2013 | 0 |
Impact Factor:
Sherpa Romeo:
Prace opublikowane w tym czasopiśmie
Filtry
wszystkich: 11
Katalog Czasopism
Rok 2024
-
Deep learning-enabled integration of renewable energy sources through photovoltaics in buildings
PublikacjaInstalling photovoltaic (PV) systems in buildings is one of the most effective strategies for achieving sustainable energy goals and reducing carbon emissions. However, the requirement for efficient energy management, the fluctuating energy demands, and the intermittent nature of solar power are a few of the obstacles to the seamless integration of PV systems into buildings. These complexities surpass the capabilities of rule-based...
-
Desirability-based optimization of dual-fuel diesel engine using acetylene as an alternative fuel
Publikacjahe study examined the dual-fuel engine performance employing acetylene gas as primary fuel and diesel as pilot fuel. The engine's operational parameters were adjusted using the Box-Behnken design, and the results were recorded. The best operating settings were yielded as 81.25 % engine load, 4.48 lpm acetylene gas flow rate and the compression ratio were 18. At this optimized setting the BTE was 27.1 % and the engine emitted 360...
-
Development of advanced machine learning for prognostic analysis of drying parameters for banana slices using indirect solar dryer
PublikacjaIn this study, eXtreme Gradient Boosting (XGBoost) and Light Gradient Boosting (LightGBM) algorithms were used to model-predict the drying characteristics of banana slices with an indirect solar drier. The relationships between independent variables (temperature, moisture, product type, water flow rate, and mass of product) and dependent variables (energy consumption and size reduction) were established. For energy consumption,...
-
Fuzzy logic-supported building design for low-energy consumption in urban environments
PublikacjaClimate, building materials, occupancy patterns, and HVAC (heating, ventilation, and air conditioning) systems all interact in complex ways, making it difficult to design low-energy buildings. Thus, innovative architectural and engineering design strategies are required to meet the worldwide need to decrease building energy usage. To improve the calculation of energy consumption of buildings, this work introduces the FCR-BCS (fuzzy...
Rok 2023
Rok 2022
-
Slowly-closing valve behaviour during steam machine accelerated start-up
PublikacjaThe paper discusses the state of stress in a slowly-closing valve during accelerated start-up of a steam turbine. The valve is one of the first components affected by high temperature gradients and is a key element on which the power, efficiency and safety of the steam system depend. The authors calibrated the valve model based on experimental data and then performed extended Thermal-FSI analyses relative to experiment. The issue...
-
Thermal cooling process by nanofluid flowing near stagnating point of expanding surface under induced magnetism force: A computational case study
PublikacjaThis paper is dedicated to the exam of entropy age and research of the effect of mixing nanosolid additives over an extending sheet. In this review, Newtonian nanofluid version turned into researched at the actuated appealing field, heat radiation and variable heat conductivity results. With becoming modifications, the proven PDEs are moved into popular differential situations and paintings mathematically making use of a specific...
-
Thermal visualization of Ostwald-de Waele liquid in wavy trapezoidal cavity: Effect of undulation and amplitude
PublikacjaThe present study is concerned with the numerical simulations of Ostwald-de Waele fluid flow in a wavy trapezoidal cavity in the presence of a heated cylinder situated at the center of the cavity. The work consists in characterizing the mixed convection as a function of the intensity of heat flow. The flow behaviour and temperature distribution in a cavity are the main focus of this study. The lower wall of the cavity is fixed...
Rok 2021
-
Heat exchange enhancement of jet impingement cooling with the novel humped-cone heat sink
PublikacjaJet impingement cooling technology is applicable to control temperature of devices, where very high heat flux is generated within a small area. This paper is about the improvement of the jet impingement cooling efficiency by the heat sink geometry modification. Two reference cases were sourced from the literature – flat heat sink and modified one with cone in the jet stagnation region. Such a change improves cooling capability...
-
Heat transfer enhancement through nanofluids with applications in automobile radiator
Publikacja -
Thermal visualization of Ostwald-de Waele liquid in wavy trapezoidal cavity: Effect of undulation and amplitude
Publikacja
wyświetlono 1207 razy