Wyszukiwarka
Nie znaleźliśmy wyników w zadanych kryteriach!
Ale mamy wyniki w innych katalogach.Filtry
wszystkich: 4971
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: MATERIAL REMOVAL RATE
-
Analysis of Roughness, the Material Removal Rate, and the Acoustic Emission Signal Obtained in Flat Grinding Processes
PublikacjaIn this work, the analysis of the acoustic emission (AE) signal in grinding processes is addressed. The proposed analysis method decomposes the acoustic signal into three frequency ranges. The total energy of each range is determined, as well as the highest frequency. Different grinding experiments were carried out, according to a full factorial design of experiments (DOE), in which feed speed, depth of cut, and transversal step...
-
Multi-objective optimization of tool wear, surface roughness, and material removal rate in finishing honing processes using adaptive neural fuzzy inference systems
PublikacjaHoning processes are usually employed to manufacture combustion engine cylinders and hydraulic cylinders. A crosshatch pattern is obtained that favors the oil flow. In this paper, Adaptive Neural Fuzzy Inference System (ANFIS) models were obtained for tool wear, average roughness Ra, cylindricity and material removal rate in finish honing processes. In addition, multi-objective optimization with the desirability function method...
-
Preliminary Results from the Removal of Phosphorus Compounds with Selected Sorption Material
PublikacjaDue to the resources of phosphorous are limited and are exhausted in the next 30 years the management of the resources is become current issue. Most of the phosphorus compounds is lost forever, because it is discharged with sewage into surface waters, causing eutrophication and in this way causing a further problem and challenge. On the other hand, there is a considerable need for phosphorus compounds, primarily in bioavailable...
-
Magnetic Porous Material Derived from Ni-MOF for the Removal of Tetracycline from Aqueous Solution
PublikacjaThe efficient removal of antibiotic residues from aqueous solution is very important for water security. Studies have found that adsorption is widely used for the removal of antibiotics due to its cost-effectiveness, low energy consumption, simplicity of operation, and environmental friendliness. In this study, a novel magnetic porous carbon adsorbent (Ni-MPC-400) with a high adsorption capacity and saturation magnetization was...
-
The use of Preston equation to determine material removal during lap-grinding with electroplated CBN tools
PublikacjaGrinding executed in a lapping configuration is an alternative finishing process benefiting from both grinding and free-abrasive machining, while minimizing the heat effect impact. Electroplated tools can be effectively used in different abrasive processes, including high-speed grinding, however, the assessment of machining performance over time is a key factor in their correct use to achieve satisfactory technological results....
-
Rate performance of the V2O5 nanocrystals as cathode material in Li-ion batteries
Dane BadawczeThe DataSet contains the galvanostatic charge/discharge curves of the V2O5 nanocrystals obtained by the sol-gel method. The battery tests of the samples were performed using the Atlas-Sollich 0961 (Atlas-Sollich, Poland) with different current densities in the voltage range between 2.0 V and 4.0 V vs. Li/Li+. Here 1C is 294 mAh g-1.
-
Rate performance of the V2O5 nanorods as cathode material in Li-ion batteries
Dane BadawczeThe DataSet contains the galvanostatic charge/discharge curves of the V2O5 nanorods obtained by the sol-gel method. The battery tests of the samples were performed using the Atlas-Sollich 0961 (Atlas-Sollich, Poland) with different current densities in the voltage range between 2.0 V and 4.0 V vs. Li/Li+. Here 1C is 294 mAh g-1.
-
Rate performance of (NH4)2V10O25·8H2O as cathode material in Li-ion batteries
Dane BadawczeThe DataSet contains the galvanostatic charge/discharge curves of the ammonium vanadate nanostructures obtained by the hydrothermal method under an initial pressure of 50 bar ((NH4)2V10O25·8H2O). The battery tests of the samples were performed using the ATLAS 0961 MBI multichannel battery testing system with different current densities in the voltage...
-
Treatment of landfill leachate in a constructed free water surface wetland system over a decade – Identification of disturbance in process behaviour and removal of eutrophying substances and organic material
PublikacjaAn 8 ha free water surface wetland system in Örebro, Sweden, which has sediment traps followed by 10 ponds for treatment of landfill leachate in the methanogenic stage, was studied from 2003 to 2012. The wetland was irregularly loaded and the leachate characteristics showed high temporal and spatial variability, so Multivariate Statistical Process Control was chosen as the diagnostic tool for detecting anomalies prior to assessing...
-
Rate performance of mixture (NH4)2V6O16 and (NH4)2V10O25·8H2O as cathode material in Li-ion batteries
Dane BadawczeThe DataSet contains the galvanostatic charge/discharge curves of the ammonium vanadate nanostructures obtained by the hydrothermal method without initial pressure (mixture (NH4)2V6O16 and (NH4)2V10O25·8H2O). The battery tests of the samples were performed using the ATLAS 0961 MBI multichannel battery testing system with different current densities...