Wyniki wyszukiwania dla: SHEAR CUP

• Verification of punching shear outside the shear cap by the direct method

  Publikacja

  • M. Grabski
  • A. Ambroziak

  - Archives of Civil Engineering - Rok 2022

  The proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...

  Pełny tekst do pobrania w portalu

• Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs

  Publikacja

  • M. Grabski
  • A. Ambroziak

  - Materials - Rok 2022

  The scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...

  Pełny tekst do pobrania w portalu

• Shear Cap Size Selection Method Based on Parametric Analysis of ACI-318 Code and Eurocode 2 Standard

  Publikacja

  • M. Grabski
  • A. Ambroziak

  - Materials - Rok 2020

  The scope of the paper is to propose a method for determining the size of shear caps in a slab–column-connections-reinforced concrete structure. Usually, shear heads are used to enhance slab–column connection, especially when the transverse reinforcement does not give the required punching shear load capacity. The dimensions of the shear head should provide the punching shear resistance of the connection inside and outside the...

  Pełny tekst do pobrania w portalu

• Shear band evolution phenomena in direct shear test modelled with DEM.

  Publikacja

  • M. Nitka
  • A. Grabowski

  - POWDER TECHNOLOGY - Rok 2021

  A direct shear test is widely used in the geotechnical engineering field. It is an easy and quick test to measure the shear properties of soil. This test often replaces more expensive and difficult tri-axial shear test. Despite that the direct shear test is known and used for a long time, it is still not well investigated at the grain scale. This paper deals with the micro behaviour of the cohesionless sand inside the direct shear...

  Pełny tekst do pobrania w portalu

• Resilient Interface Shear Modulus for Characterizing Shear Properties of Pavement Base Materials

  Publikacja

  • B. Han
  • J. Ling
  • X. Shu
  • H. Gong
  • Y. Sun
  • P. Polaczyk
  • B. Huang

  - JOURNAL OF MATERIALS IN CIVIL ENGINEERING - Rok 2018

  Pełny tekst do pobrania w serwisie zewnętrznym

• FE-investigation of shear localization in granular bodies under high shear rate

  Publikacja

  • J. Tejchman
  • W. Wu

  - GRANULAR MATTER - Rok 2008

  Artykuł omawia wpływ prędkości ścinania an lokalizację odkształceń wwąskiej warstwie piasku poddanej ścinaniu. Obliczenia wykonano przyzastosowaniu metody elementów skończonych i mikropolarnego modeluhipoplastycznego rozszerzonego o lepkość.

• Juridicas CUC

  Czasopisma

  ISSN: 1692-3030 , eISSN: 2389-7716

• INGE CUC

  Czasopisma

  ISSN: 0122-6517 , eISSN: 2382-4700

• CUR Quarterly

  Czasopisma

  ISSN: 1072-5830

• Process Control Challenges and Solutions: TEOS, W, and CU CMP

  Publikacja

  • J. Mendonca
  • C. Dang
  • S. Selinidis
  • M. Angyal
  • B. Boeck
  • R. Islam
  • C. Pettinato
  • P. Grudowski
  • J. Cope
  • B. Smith... i 2 innych

  - MRS Proceedings - Rok 1999

  Pełny tekst do pobrania w serwisie zewnętrznym