Publications
Filters
total: 733
Catalog Publications
Year 2017
-
Requirements, modifications and methods of mechanical testing of bone cement – literature review
PublicationThe Aim of the paper is to show the basic requirements for the bone cement, its modifications in terms of physical, mechanical and biological properties and testing methods. This publication is intended to be a source of systematized basic knowledge regarding the modified bone cement.
-
Report on investigation of turbine blade from main engine turbocharger 420.34 from M/V "Nordstraum"
PublicationWykonano badania pęknięcia na łopatce turbiny turbodoładowania silnika głównego. Ustalono, ze przyczyną pęknięcia była korozja międzykrystaliczna.
-
Reduction of road traffic noise by source measures — present and future strategies
PublicationThe current trend worldwide is less focused on reducing road traffic noise. This is in strong contrast to the severe impact of traffic noise to the general health and quality of life. A more holistic and combined strategy is needed. Current international rules and regulations regarding vehicles and tyres are not sufficient to reduce traffic noise levels in an effective way. Calculations show that these regulations will only yield...
-
Properties of Composite Oxide Layers on The Ti13Nb13Zr Alloy
PublicationThe development of composite oxide layers on the Ti13Nb13Zr alloy, their structure and properties have been demonstrated. Two subsequent methods were applied to prepare the composite layers. During the first stage gas oxidation produced a solid oxide layer, and subsequently oxide nanotubes were produced by using an electrochemical method. Scanning electron microscopy (SEM), chemical analysis, energy dispersive X-ray spectroscopy...
-
Powikłania po rekonstrukcji piersi: problem zakażeń i strategii prewencyjnej - przegląd literaturowy
PublicationW niniejszej pracy przedstawiono dane dotyczące powikłań po rekonstrukcji piersi. Manuskrypt ma na celu usystematyzowanie wyników badań z ostatnich lat wraz z aspektami, takimi jak: częstotliwość występowania powikłań oraz ich rodzaj, czynniki predysponujące, a także możliwości profilaktyki. Przeanalizowano dane literaturowe z ogólnie dostępnych artykułów z okresu ostatnich pięciu lat, ze szczególnym uwzględnieniem zakażeń. Do...
-
Powierzchniowe badania mikrosejsmiczne na odwiercie w północnej Polsce, optymalizacja modelu prędkościowego
PublicationCelem wykonanych prac było potwierdzenie możliwości wykorzystania mikrosejsmicznego pomiaru powierzchniowego ze schematem rozłożenia typu patch array dla polskich warunków geologicznych. Artykuł zawiera opis przeprowadzonych prac mikrosejsmiki powierzchniowej wykonanych na odwiercie w północnej Polsce wraz z procedurą optymalizacji modelu prędkościowego.
-
Planning, Configuration and Usefulness of Microseismic Monitoring on Eastern-Europe Platform – Example from East Pomerania
PublicationThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing process. The method uses array of geophones to localize micro tremors induced by liquid pumped underground at high rate and pressure. The acquired information helps to optimize fracturing process and prevents fracture growth to aquifer levels. It proved to be useful on several unconventional hydrocarbon reservoirs in the USA....
-
Opracowanie technologii spawania naprawczego szyn poddźwigowych A120 oraz badania nieniszczące jakości szyn w DCT w Porcie Północnym
PublicationEkspertyza dotyczy realizacji zlecenia związanego z naprawą spoin szyn poddźwigowych na terenie terminalu kontenerowego - Deep Water Terminal (DCT) w Porcie Północnym w Gdańsku. W ramach opracowania: 1. Wykonano badania ultradźwiękowe (UT) i magnetyczno-proszkowe (MT) spoin czołowych szyn poddźwigowych typu A120, według schematu dostarczonego przez firmę SKANSKA S.A. 2. Wykonano analizę wyników badań...
-
Ocena stanu technicznego reaktorów R02 ÷ R05 instalacji 0410 oraz rurociągów łączących piece z reaktorami w Zakładzie Paliwowym (PZP) po postoju remontowym w 2017r. Grupa LOTOS S.A. w Gdańsku
PublicationPrzedmiotem pracy było wykonanie oceny stanu technicznego reaktorów instalacji 410 i rurociągów łączących piece z reaktorami, na podstawie przeprowadzonych badań nieniszczących, które zostały przeprowadzone podczas planowego postoju instalacji w 2017r, oraz badania niszczące rurociągu 18"-041-P041.
-
Ocena stanu technicznego reaktorów 440 R01÷ R04 na instalacji platformingu CCR po postoju remontowym w 2017r
PublicationPrzedmiotem pracy było wykonanie oceny stanu technicznego reaktorów 440-R01÷R04 na instalacji platformingu CCR, po postoju remontowym w 2017
-
Ocena stanu technicznego kompensatorów wylotowych (pigtaili) rur katalitycznych z reformera 0250-F101
PublicationCelem badań było ustalenie stanu materiału rur kompensatorów wylotowych rur katalitycznych z reformera metanu po eksploatacji. Wykonano badania niszczących odcinków rur, analizę spektralną składu chemicznego, badania metalograficzne mikroskopowe, pomiary twardości i mikrotwardości, statyczne próby rozciągania w temperaturze pokojowej. Dokonano oceny stopnia degradacji materiału rur z orzeczeniem o aktualnym stanie technicznym kompensatorów.
-
Ocena stanu technicznego i prognoza trwałości eksploatacyjnej rurociągów 20” 044-P101 ÷ P107 i 2”044-P115 na instalacji 440 platformingu CCR po postoju remontowym w 2017r. Grupa LOTOS S.A. w Gdańsku
PublicationPrzedmiotem pracy było wykonanie oceny stanu technicznego rurociągów 20” 440-044-P101 ÷ 044-P107 i rurociągu 2” 044-P115, po postoju remontowym w 2017r. Przeprowadzono badania nieniszczące i niszczące rurociągów. Wydano opinię dotyczącą stanu aktualnego rurociągów i prognozę trwałości .
-
Ocena stanu degradacji rur katalitycznych ze staliwa Manaurite XM po długotrwałej eksploatacji w podwyższonej temperaturze
PublicationW artykule poruszono temat dotyczący oceny stanu degradacji rur katalitycznych ze staliwa Manaurite XM po długotrwałej eksploatacji w podwyższonej temperaturze. Spośród wielu mierników stanu degradacji materiału rur analizowano przyrost średnicy wewnętrznej rury, obraz mikrostruktury oraz właściwości mechaniczne w temperaturze pokojowej. Przeprowadzono statyczne próby rozciągania materiału rur, badania metalograficzne mikroskopowe...
-
Noise related to gas bottles explosions
PublicationModern industrialized world is in a never ending danger of accidents and catastrophes of technical nature. Some of them may involve fires and explosions of gas storage bottles or containers. Technical University of Gdansk, Poland performed numerous tests where bottles containing acetylene, oxygen, hydrogen, CO2, LPG, LNG or CNG were blown due to excessive temperature caused by fire. Although those experiments were not focused on...
-
Napawanie elementów wymiennika ciepła austenitycznym drutem proszkowym
PublicationNa potrzeby przemysłu energetycznego produkuje się wymienniki ciepła przeznaczone do eksploatacji w warunkach agresywnych chemicznie, np. w środowisku siarkowodoru. Z przyczyn ekonomicznych często stosuje się w takim przypadku materiały bimetaliczne wytwarzane procesami napawania. W artykule przedstawiono wyniki badań nieniszczących, pomiarów twardości, analizy składu chemicznego, pomiarów ferrytu delta oraz badań makro- i mikroskopowych...
-
Możliwości sterowania ilością wodoru dyfundującego w złączach spawanych
PublicationW pracy omówiono metalurgiczne i technologiczne czynniki wpływające na obecność wodoru dyfundującego w stopiwie uzyskanym w środowisku powietrznym i pod wodą oraz podano metody obniżania jego ilości. Przedstawiono wyniki badań ukierunkowanych na określenie wpływu warunków i parametrów spawania na nawodorowanie stopiwa. Opracowano i podano zależności umożliwiające prognozowanie zawartości wodoru w złączach wykonanych pod wodą...
-
Microseismic Monitoring of Hydraulic Fracturing - Data Interpretation Methodology With an Example from Pomerania
PublicationMicroseismic monitoring is a method for localizing fractures induced by hydraulic fracturing in search for shell gas. The data is collected from an array of geophones deployed on the surface or underground. Ground vibrations are recorded and analysed for fracture location, magnitude and breakage mechanism. For successful microseismic monitoring one need a velocity model of underlying formations. The model is further tuned with...
-
MICROSEISMIC EVENT DETECTION USING DIFFERENT ALGORITHMS ON REAL DATA FROM PATCH ARRAY GEOPHONE GRID FROM EASTERN POMERANIA FRACTURING JOB
PublicationThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing process. Hydraulic fracturing is a method of reservoir stimulation used especially for unconventional gas recovery. A matrix of several thousand geophones is placed on the surface of earth to record every little tremor of ground induced by fracturing process. Afterwards, the signal is analysed and the place of tremor occurrence...
-
Mechanical characteristics of welded joints between different stainless steels grades
Publicationnvestigation of mechanical characteristics of welded joints is one of the most important tasks that allow determining their functional properties. Due to the very high, still rising, cost of some stainless steels it is justified, on economic grounds, welding austenitic stainless steel with steels that are corrosion-resistant like duplex ones. According to forecasts the price of...
-
MATCHED FILTER APPROACH FOR MICROSEISMIC SIGNAL PROCESSING OF REAL DATA FROM EAST POMERANIA SHALE GAS
PublicationThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing (HF)process. An array of several hundred geophones is placed on the surface to record little ground tremors induced by fracturing process. Filtration and summation of signals from geophones is essential to identify and locate fracturing events from underground. Authors propose a method of matched filtering, that is usually...
-
Kompozyt metalowy zgrzewany wybuchowo Zastosowanie zgrzewania wybuchowego do wytwarzania kompozytów metalowych o osnowie aluminiowej
PublicationEnergia wybuchu może zostać wykorzystana do realizacji wielu procesów technologicznych, m.in. wytwarzania złączy zgrzewanych, prasowania proszków, tłoczenia, odprężania i utwardzania metali. Bardzo interesującym zastosowaniem technologii zgrzewania wybuchowego jest wytwarzanie kompozytów metalowych. W artykule scharakteryzowano kompozyty metalowe i zgrzewanie wybuchowe jako jedną z metod ich otrzymywania. Przedstawiono autorską...
-
Influence of processing conditions on crystal structure of BiNbO 4 ceramics
PublicationBismuth niobate (BiNbO4) has attracted attention as a low-fired ceramics with promising microwave application potential. It belongs to the bismutocolumbite oxides with similarly to scheelite-like stibiotantalite structure (SbTaO4) A3+B5+O4. Aim of the present research was to fabricate BiNbO4 ceramics by solid state reaction route from the mixture of simple oxides viz. Bi2O3, and Nb2O5, and study its phase composition as well as...
-
Improvement of microstructure and mechanical properties of high dense sic ceramics manufactured by high-speed hot pressing
PublicationNon-oxide ceramics possess high physical-mechanical properties, corrosion and radiation resistance, which can be used as a protective materials for radioactive wastes disposal. The aim of the present study was the manufacturing of high density SiC ceramics with advanced physical and mechanical parameters. The high performance on the properties of produced ceramics was determined by the dense and monolithic structure. The densified...
-
Impact damage in SiO2 nanoparticle enhanced epoxy – Carbon fibre composites
PublicationLow velocity impact behaviour of nano-SiO2 enhanced carbon fibre/epoxy composites for naval applications is reported. Epoxy resin matrix was enhanced by 1- 8 wt% SiO2 nanoparticles, based on industrial surface-modified nanosilica. Impact parameters: force, deformation, energy, damage size were recorded. The most pronounced effect was damage size decrease; e.g. ∼28% recorded by infrared thermography and X-ray computed radiography...
-
Hydroxyapatite deposition on the laser modified Ti13Nb13Zr alloy
PublicationThe Ti13Nb13Zr alloy was subjected to laser modification with the Nd:YAG laser provided that such treatment would increase the surface roughness followed improved adhesion of hydroxyapatite (HAp) coatings The hydroxyapatite was deposited by electrophoretic method in suspension of 0.5 g HA powder and 100 ml ethyl alcohol. The deposition was carried out for 10 min at 10 V voltage followed by drying at room temperature for 24 h and...
-
ENVIRONMENTAL DEGRADATION OF DISSIMILAR AUSTENITIC 316L AND DUPLEX 2205 STAINLESS STEELS WELDED JOINTS
PublicationThe paper describes structure and properties of dissimilar stainless steels welded joints between duplex 2205 and austenitic 316L steels. Investigations were focused on environmentally assisted cracking of welded joints. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement was determined in slow strain rate tests (SSRT) with the strain rate of 2.2 × 10–6 s–1. Chloride-inducted SCC was determined in the...
-
Electrophoretic deposition (EPD) of nanohydroxyapatite - nanosilver coatings on Ti13Zr13Nb alloy
PublicationTitanium and its alloys are the biomaterials most frequently used in medical engineering, especially as parts of orthopedic and dental implants. The surfaces of titanium and its alloys are usually modified to improve their biocompatibility and bioactivity, for example, in connection with the deposition of hydroxyapatite coatings. The objective of the present research was to elaborate the technology of electrophoretic deposition...
-
Ekspertyza przyczyn uszkodzenia zaworu kulowego 1/2"
PublicationWykonano badania przyczyn uszkodzenia zaworu kulowego wykonanego z mosiądzu. Jako przyczynę wskazano korozjęe naprężeniową.
-
Ekspertyza przyczyn uszkodzenia krzywek mocowania baterii wannowej
PublicationWykonano badania celem ustalenia przyczyn uszkodzenia krzywek do mocowania baterii wykonanych z mosiądzu. Jako przyczynę wskazano korozję międzykrystaliczną.
-
Diffusible hydrogen management in underwater wet self-shielded flux cored arc welding
PublicationThis article reports the effect of underwater wet welding parameters and conditions on the diffusible hydrogen content in deposited metal for welding with a self-shielded flux cored wire. The diffusible hydrogen content in deposited metal was determined using the glycerin method according to the Plackett-Burman design determining the significance of the effect of the stick out length, welding current, arc voltage, travel speed...
-
DIAGNOSTYKA STANU TECHNICZNEGO IZOLATORÓW PRZEPUSTOWYCH ŚREDNIEGO NAPIĘCIA
PublicationW referacie przedstawiono zasady sprawdzania jakości izolatorów przepustowych średniego napięcia (SN) za pomocą metody radiograficznej (RT) oraz pomiaru wyładowań niezupełnych (wnz). Ostatnie badanie jest jedną z pozycji zawartych w badaniach wyrobu normy [5]. Dodatkowo badania te rozszerzono o próby napięciem probierczym przemiennym. Z uwagi na negatywne wyniki pomiaru wnz za pomocą metody RT udało się określić lokalizację wtrąceń...
-
Deposition of phosphate coatings on titanium within scaffold structure
PublicationPurpose: Existing knowledge about the appearance, thickness, and chemical composition of phosphate coatings on titanium inside porous structures is insufficient. Such knowledge is important for the design and fabrication of porous implants. Methods: Metallic scaffolds were fabricated by selective laser melting of 316L stainless steel powder. Phosphate coatings were deposited on Ti sensors placed either outside the scaffolds or...
-
Degradation of reference tyres used for CPX measurements
PublicationMeasurements of tyre/road noise using the Close Proximity Method are based on reference tyres that are described in ISO/TS 11819-3. The standard specifies two tyres, namely "P1" and "H1" that should be used during measurements. To be used for measurements each tyre must fulfill certain conditions that are listed in the standard. The conditions are related to the tread pattern depth and rubber hardness. During experiments performed...
-
Degradation of implantable materials – in vivo and in vitro research
PublicationThe article concerns the biological and electrochemical degradation of metallic implants in vivo and in vitro studies. The in vivo research dealt with degradation of plates used to join bones, as well as endoprostheses. The most common damages were: metalosis, breaking in the microstructure changes, breaking in area of holes, as well as plastic deformation throughout the length of an implant. The material used for the research...
-
Corrosion degradation of spacers – examination of changes in bone cement coating.
PublicationSpacer is a special implant used at the time of infection after endoprosthetic surgery. It consists of a metal core and bone cement coating with an antibiotic. In the human body spacers are exposed to degradation processes. This paper looks at the effect of corrosion on spacers. Electrochemical corrosion tests were performer on titanium pins with bone cement coating in two solutions: Ringer’s solution and artificial...
-
Corrosion behavior of hydrogen charged super duplex stainless steel welded joints
PublicationThe electrochemical behavior of the weld metal, heat-affected zone (HAZ), and base material of super duplex stainless steel (SDSS) welded joints, made with the application of flux-cored arc welding (FCAW) and submerged arc welding (SAW), were investigated with the use of metallographic examinations (optical microscopy and scanning electron microscopy), potentiodynamic polarization measurements and total hydrogen content determination...
-
Bioaktywność i biofunkcyjność cementu kostnego
PublicationOpracowanie dotyczy modyfikacji cementu kostnego w celu nadania mu właściwości bioaktywnych i biofunkcyjnych. Jego celem jest scharakteryzowanie cementu kostnego oraz obecnie stosowanych dodatków, któr e nadają mu właściwości przeciwdrobnoustrojowe oraz osteointegracyjne. Opracowanie zawiera opis badań własnych przeprowadzonych przez autorkę w aspekcie wytwarzania powłoki antybakteryjnej...
-
Badanie wpływu zmiany składu gazów osłonowych na spawanie metodą MIG stopu aluminium EN AW 7075. Innowacyjne wykorzystanie w wiertnictwie.
PublicationStop aluminium AW-7075 zyskuje coraz większą popularność w zastosowaniach komercyjnych ze względu na jego wyjątkowe właściwości fizyczne i mechaniczne: małą gęstość, wysoką wytrzymałość, udarność i plastyczność, bardzo dużą odporność na zmęczenie i zadowalającą na korozję, łatwą obrabialność i przetwarzalność. Ze względu na te właściwości, stop ten (AlZn5,5MgCu), zwany też FORTAL-em, używany jest dla części narażonych na wysokie...
-
Badania śrub kominów 250, 120, 270, 9800
PublicationPrzedmiotem pracy było wykonanie badań pękniętych śrub komina 250 oraz ustalanie przyczyn ich uszkodzenia. Przedmiotem drugiego zadania było wykonanie badań weryfikacyjnych śrub pobranych z połączeń kołnierzowych kominów 120, 270 i 9800.
-
Badania bioaktywności modyfikowanego cementu kostnego – przegląd literaturowy
PublicationCelem pracy jest przybliżenie aspektów związanych z modyfikowaniem cementu kostnego w celu nadania mu właściwości bioaktywnych. Przedstawiono obecnie stosowane bioaktywne modyfikacje, które mają charakter profilaktyczny (zapobiegają infekcjom), terapeutyczny (zwalczają bakterie) oraz pobudzający osteointegrację. Ukazano metody oceny modyfikacji bioaktywnych i zreferowano ich procedury, m.in. badania mikroskopowe, starzenie w roztworze...
-
Assessment of crack resistance of ship steels according to SEP 1390 standard
PublicationThe aim of the study was to evaluate the weldability of E36 nd NVE-36 steels by bending test according to SEP 1390. In the case of the specimen from E36 steel 9 external cracks were found, 5 of which were stopped in the fusion line and 4 in heat affected zone. In the case of the specimen from NVE-36 steel 8 external cracks were found, 4 of which were stopped in the fusion line and 4 in heat affected zone. Results of bending test...
-
Assessment of crack resistance of S355J2+N steel according to SEP 1390 standard
PublicationThe aim of the study was to evaluate the weldability of S355J2+N steel by bending test according to SEP 1390. In the specimen from S355J2+N steel 3 external cracks were found, 1 of which were stopped in the fusion line and 2 in heat affected zone. Results of bending test for investigated grade of steel are positive.
-
Analysis of features of stainless steels in dissimilar welded joints in chloride inducted corrosion
PublicationStainless steels of femtic-austenitic microstructure that means the duplex Cr-Ni-Mo steels, in comparison with austenitic steel includes less expensive nickel and has much better mechanical properties with good formability and corrosion resistance, even in environments containing chloride ions. Similar share of high chromium ferrite and austenite, which is characterized by high ductility, determines that the duplex steels have...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublicationTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
3D Printing of Metallic Implants
PublicationThe fabrication of various elements, solid and open porous structures of stainless steel and Ti alloy is described. The process was started with the design of 3D models in CAD/CAM system. The 3D models were transformed into *.stl files and then the manufacturing process of the real structures by means of the selective laser melting with the SLM Realizer 100 3D printer was made. The paper shows the porous specimens made for possible...
Year 2016
-
Zastosowanie próby implant do oceny spawalności stali
PublicationPraca dotyczy oceny spawalności stali o podwyższonej i wysokiej wytrzymałości w aspekcie eksperymentalnego określania skłonności do tworzenia pęknięć zimnych. W artykule opisano metodykę określania wrażliwości na pękanie próbą implant. Przedstawiono również proponowane w literaturze i autorskie sposoby opracowywania i przedstawiania wyników badań rozpatrywaną metodą i ich interpretacji.
-
Wpływ zaburzeń geometrii na proces wypierania w przestrzeni pierścieniowej otworów wiertniczych
PublicationIzolacja stref zbiornikowych, przenoszenie części naprężeń oraz spowolnienie tempa erozji rur okładzinowych to główne zadania płaszcza cementacyjnego. Powstaje on na skutek stopniowego wyparcia płuczki przez ciecze buforowe, a następnie cieczy buforowych przez zaczyn cementowy. Niepowodzenie tej operacji skutkować może katastrofą na miarę wycieku ropy w Zatoce Meksykańskiej w 2010 roku. Mimo że problem niewystarczającego związania płaszcza...
-
Wpływ nawodorowania na odporność korozyjną stali superdupleks spawanej metodą SAW
PublicationW pracy przedstawiono wyniki badań metodą potencjodynamiczną odporności korozyjnej złączy ze stali superdupleks wykonanych procesem SAW. Ustalono, że największą wrażliwością na korozję charakteryzuje się spoina.
-
Wpływ nawierzchni i opon na opór toczenia
PublicationArtykuł porusza zagadnienia wpływu nawierzchni jezdni i konstrukcji opon na jeden z istotnych parametrów opisujących współpracę opony z jezdnią, jakim jest opór toczenia. Artykuł nawiązuje do publikacji, w których omówiony jest wpływ oporu toczenia na zużycie energii przez pojazdy samochodowe oraz przedstawione są w ogólnym zarysie metody badania oporu toczenia opon.
-
Wpływ namagnesowania elektrod otulonych na złącza spawane pod wodą metodą mokrą
PublicationDokonano analizy wpływu namagnesowania elektrod otulonych na geometrię i właściwości złączy teowych ze spoinami pachwinowymi wykonanych ze stali S235JR w środowisku wodnym. Stwierdzono, że dla zastosowanych warunków i parametrów spawania namagensowanie elektrod wpływa na stabilność jarzenia się łuku, powstawanie niezgoności spawalniczych typu błędy kształtu, natomiast nie ma wpływu na budowę mikrostrukturalną i twardość złączy...
-
Właściwości złączy różnoimiennych stopu niklu Incoloy 800H ze stalą odporną na korozję 316L
PublicationW artykule przedstawiono problemy związane z wykonywaniem połączeń różnoimiennych typu Incoloy 800HT – austenityczna stal odporna na korozję 316L. Wykonano badania nieniszczące oraz niszczące, których wyniki pozwoliły na weryfikacje jakości wykonanych złączy próbnych. Nie stwierdzono występowania niezgodności spawalniczych oraz uzyskano wysokie właściwości wytrzymałościowe złączy. Badania metalograficzne ujawniły poprawne struktury...
-
Weldability of S460ML High Strength Low Alloy Steel in Underwater Conditions
PublicationThe paper presents experimental evaluation of susceptibility of the high strength S460ML steel to cold cracking in the conditions of wet welding with the use of covered electrodes. From the results of Tekken tests it was found out that the investigated steel was characterised, in the conditions of the carried out experiments (underwater wet welding and air welding with rutile electrodes), of high susceptibility to cold cracking....
-
Weldability of high strength steel in underwater environment
PublicationThe article describes the problems with weldability of high-strength steels in the aquatic environment. The tendency of steel S355J2G3 and S500M to form cold cracks when welded in wet welding conditions has been experimentally evaluated. It was found that the tested steels have a high propensity to cracking. An experiment has been proposed and tested to evaluate the usefulness of the tempering bead technique as a method of improving...
-
Ustalenie przyczyn uszkodzenia gazociągu wysokiego ciśnienia DN100 - odgałęzienie do SG Czersk
PublicationNa zlecenie przedsiębiorstwa Polska Spółka Gazownictwa sp. z o.o. Oddział w Gdańsku wykonano badania fragmentu rury gazociągu wysokiego ciśnienia DN100 - odgałęzienie do SG Czersk eksploatowanego przez ponad 20 lat. Po tym okresie wykryto wyciek (ulatnianie) gazu. Na podstawie analizy technologii gięcia rur o dużych średnicach oraz wyników badań wizualnych i metalograficznych makroskopowych ustalono, że przyczyną awarii badanego...
-
Ultra Low Noise Poroelastic Road Surfaces
PublicationNoise is one of the most important environmental problems related to road traffic. During the last decades, the noise emitted by the engines and powertrains of vehicles was greatly reduced and tires became a clearly dominant noise source. The article describes the concept of low noise poroelastic road surfaces that are composed of mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and...
-
The influence of biological environment on the silver-coated implants
PublicationThis paper deals with implants covered with nanosilver
-
THE EFFECT OF WET UNDERWATER WELDING ON COLD CRACKING SUSCEPTIBILITY OF DUPLEX STAINLESS STEEL
PublicationABSTRACT The present work was conducted to assess the weldability of duplex stainless steel in underwater conditions. Metal manual arc welding (MMA) with the use of coated electrodes was used in the investigations. Tekken weldability tests were performed underwater at 0.5 m depth and in the air. Nondestructive tests, metallographic examinations of welds, ferrite content assessment in microstructure and hardness test were performed....
-
The determinants of morphology and properties of the nanohydroxyapatite coating deposited on the Ti13Zr13Nb alloy by electrophoretic techniqe
PublicationThe titanium and its alloys belong at present to the most preferred and commonly applied biomaterials for load- bearing implants. The surfaces of biomaterials are subjected to modification, including the hydroxyapatite coatings deposited in order to ensure corrosion resistance and better joining between an implant and a bone through the possibility of ingrowth bone into the coating. In this paper, the morphology and properties...
-
The allergic and irritating reactions to metallic implants with trauma - orthopaedic patients
PublicationThe article presents the analysis of clinical operation complications after the treatment of long bones by mean of ostheosynthesis with the use of metal implants and endoprothesoplastic of hip joints.
-
Temper bead welding of S420G2+M steel in water environment
PublicationThe article presents the idea of the use of Temper Bead Welding (TBW) technique to improve the weldability of high strength steel at underwater wet welding conditions. Wet welding method with the use of covered electrodes is described. This work shows results of metallographic examinations and hardness measurements of samples of S420G2+M steel with weld beads performed under water. It has been shown that Temper Bead Welding technique...
-
Styrene epoxidation over heterogeneous manganese(III) complexes
PublicationThe manganes(III) complex functionalised with 2,3-dihydropyridazine has been encapsulated in the supercages of the NaY zeolite using two different procedures, flexible ligand and in situ complex. The parent zeolite and the encapsulated manganese(III) complexes were screened as catalysts for styrene oxidation by using t-BOOH as the oxygen source in acetonitrile. Under the optimized conditions, the catalysts exhibited moderate activity...
-
Studies of the mechanism of metal metal dusting of 10CrMo9-10 steel after 10 years of operation in trhe semi-regenerative catalytic reformer
PublicationThe study showed that metal dusting mechanism of 10CrMo9-10 steel operated in industrial environment differs from models developed in laboratories. Significant differences lie in the fact that the models developed in laboratories only assume the formation of metastable carbide M3C, while studies have shown that the formation of M3C carbides is associated with the transformation of primary carbides and in the next stage is preceded...
-
STRUCTURE AND MAGNETIC PROPERTIES OF Bi5Ti3FeO15 CERAMICS PREPARED BY SINTERING, MECHANICAL ACTIVATION AND EDAMM PROCESS. A COMPARATIVE STUDY
PublicationThree different methods were used to obtain Bi5Ti3FeO15 ceramics, i.e. solid-state sintering, mechanical activation (MA) with subsequent thermal treatment, and electrical discharge assisted mechanical milling (EDAMM). The structure and magnetic properties of produced Bi5Ti3FeO15 samples were characterized using X-ray diffraction and Mössbauer spectroscopy. The purest Bi5Ti3FeO15 ceramics was obtained by standard solid-state sintering...
-
Structure and hyperfine interactions in Bi1−xNdxFeO3 solid solutions prepared by solid-state sintering
PublicationThe series of polycrystalline ceramic powders, Bi1xNdxFeO3 (x = 0.11) was successfully synthesized by mixed oxide method followed by pressureless sintering. X-ray diffraction and Mössbauer spectroscopy were used as complementary methods to study structure and hyperfine interactions of the samples. It was found that with an increase of Nd content, within the range of x = 0.20.3 a structural phase transition from rhombohedral to...
-
Stanowiska do badań kruchości wodorowej
PublicationW pracy przedstawiono wybrane aspekty niszczenia wodorowego metali oraz złączy spawanych. Przedstawiono stanowiska badawcze wykorzystywane do oceny niszczenia wodorowego, w tym zaprojektowane i wykonane w Zespole Inżynierii Spajania PG stanowisko do realizacji próby SSRT.
-
Skłonność do tworzenia pęknięć zimnych złączy ze stali ferrytyczno-austenitycznej typu dupleks 2205 przy spawaniu pod wodą metodą mokrą
PublicationSpawanie pod wodą stali ferrytyczno-austenitycznych typu dupleks budzi coraz szersze zainteresowanie. Wynika to z pilnej potrzeby opracowania spawalniczych technologii naprawczych rurociągów do transportu ropy naftowej eksploatowanych pod wodą. Do badań wykorzystano metodę mokrą przy zastosowaniu spawania elektrodami otulonymi (proces 111). Wykonano technologiczne próby Tekken pod wodą na głębokości 0,5 m oraz na powietrzu. Przeprowadzono...
-
Regeneration of marine engine valves using laser surfacing
PublicationThis article presents an analysis of the applicability of laser surfacing of the exhaust valve face of a marine diesel engine using cobalt-based powder. After preparation by machining, the selected valves were subjected to laser surfacing using a high-power ROFIN DL020 laser. The EuTroLoy 16012 powder was used in the surfacing process. One of the valves was cut and subjected to metallographic examination and hardness measurements,...
-
Projekt narzędzia typu guide-shoe w ramach Projektu NCBiR - testy otworowe
PublicationArtykuł opisuje przebieg realizacji projektu mającego na celu stworzenie nowego typu narzędzia otworowego. Projekt ten o akronimie „PPPI” realizowany jest w ramach programu strategicznego „Blue Gas” Narodowego Centrum Badań i Rozwoju. Artykuł zawiera podstawowe informacje na temat problemów, którym przeciwdziałać ma projektowane narzędzie, opis wykonanych dotychczas prac oraz wstępne wyniki z przeprowadzonych badań na wywierconych...
-
Opracowanie technologii spawania laserowego stali o wysokiej wytrzymałości
PublicationWykonano złącza spawane wiązką światła koherentnego ze stali konstrukcyjnej o ultra wysokiej wytrzymałości. Określono zakresy parametrów, które umożliwiają wykonywanie złączy doczołowych oraz napawanie badanej stali.
-
Opracowanie nowej technologii produkcji kontenerów specjalistycznych z podwójnym, perforowanym dnem do transportu, magazynowania i suszenia
PublicationCelem pracy było opracowanie nowej technologii produkcji kontenerów specjalistycznych z podwójnym, perforowanym dnem do transportu, magazynowania i suszenia dla przedsiębiorstwa produkcyjno-handlowego AMG. Opracowanie ma być podstawą zbudowania linii produkcyjnej do wykonywania kontenerów specjalistycznych z podwójnym, perforowanym dnem do transportu, magazynowania i suszenia. Wdrożona technologia ma na celu umożliwienie wytwarzania...
-
On the durability of the hydraulic satellite motor working mechanism in overload condition
PublicationThe paper presents the newest construction of the hydraulic satellite pump/motor. In this study, the fracture of the hydraulic satellite motor working mechanism is investigated. Factors influencing the durability of satellite working mechanism have been described. The durability of the hydraulic satellite motor working mechanism at a load, corresponding to a pressure of 15 MPa supplied with refined rapeseed oil is very low. Analyses...
-
Odporność kawitacyjna grubych powłok ochronnych CrC nanoszonych metodą niskociśnieniowego wyładowania łukowego (Arc-PVD)
PublicationReferat przedstawia analizę i metodę pokrywania powierzchni materiałów zastosowanych w turbinach parowych i śrubach okrętowych za pomocą CrC przy zastosowaniu metodę ARC-PVD. Celem jest podwyższenie trwałości powierzchni narażających na erozję wywołaną przez kawitację.
-
Ocena jakości złączy lutowanych płytowego wymiennika ciepła
PublicationNa podstawie wyników badań metalograficznych makro- i mikroskopowych oraz badań składu chemicznego (EDS) przeprowadzono ocenę jakości złączy lutowanych płytowego wymiennika ciepła ze stali odpornej na korozję. Stwierdzono występowanie licznych niezgodności w lutowinie oraz strefy dyfuzyjnej o ponadnormatywnej szerokości w materiale rodzimym.
-
MOODLE MOOCS - PRZYPADKI UŻYCIA W PROJEKCIE SP4CE (PARTNERSTWO STRATEGICZNE NA RZECZ KREATYWNOŚCI I PRZEDSIĘBIORCZOŚCI)
PublicationProjekt SP4CE (Partnerstwo strategiczne na rzecz kreatywności i przedsiębiorczości) jest odpowiedzią na potrzeby zidentyfikowane w komunikacie z Brugii w sprawie ściślejszej europejskiej współpracy w dziedzinie kształcenia i szkolenia zawodowego w latach 2011 - 2020. Do realizacji portalu SP4CE wykorzystano oprogramowanie WordPress i Moodle. WordPress wykorzystano m.in. do udostępnienia materiałów informacyjnych oraz szkoleniowych...
-
Kalibrator otworowy i jego wpływ na jakość zacementowania otworów wiertniczych
PublicationUszczelnianie poziomów skał zbiornikowych w orurowanych otworach wiertniczych jest najistotniejszą operacją w procesie wydobycia węglowodorów. Jej niepowodzenie grozi skażeniem środowiska, przeprowadzeniem kosztownych akcji ratunkowych i naprawczych czy w końcu koniecznością wypłaty odszkodowań. Z tego powodu rozwiązanie problemów technologicznych z uwzględnieniem szeregu czynników obejmujących fazę projektowania i wykonania zabiegu...
-
Investigations on the the dynamics of motor vehicle driving in nighttime conditions
PublicationThe article describes investigations on vehicle driving in nighttime conditions
-
Investigations of Titanium Implants Covered with Hydroxyapatite Layer
PublicationTo reduce unfavorable phenomena occurring after introducing an implant into human body various modifications of the surface are suggested. Such modifications may have significant impact on biocompatibility of metallic materials. The titanium and it's alloys are commonly used for joint and dental implants due to their high endurance, low plasticity modulus, good corrosion resistance as well as biocompatibility. Special attention...
-
Influence of Sn and Pb Ions Substitutions on Dielectric Properties of Barium Titanate
PublicationThe results of the microstructural and dielectric measurements of (Ba1-xPbx)(Ti1-xSnx)O3 (BPTSx) (x = 0, 0.05, 0.10, 0.30) polycrystalline samples are presented. The samples were obtained by means of a high temperature synthesis and their expected stoichiometry was confirmed by energy dispersive spectroscopy (EDS) measurements. The dielectric properties of BPTSx were studied with the use of broadband dielectric spectroscopy. The...
-
Influence of Processing Conditions on Crystal Structure of Bi6Fe2Ti3O18 Ceramics
PublicationAim of the present research was to apply a solid state reaction route to fabricate Aurivillius-type ceramics described with the formula Bi6Fe2Ti3O18 (BFTO) and reveal the influence of processing conditions on its crystal structure. Pressureless sintering in ambient air was employed and the sintering temperatures were 850 and 1080 °C. It was found that the fabricated BFTO ceramics were multiphase ones. They consisted of two Bim+1Fem-3Ti3O3m+3...
-
Influence of Nitriding and Laser Remelting on Properties of Austenitic Stainless Steel Type X10CrNi18-8 and Cavitation Erosion Resistance
PublicationThe paper presents properties of surface layers. Surface layers were obtained by using low temperature glow–discharge nitriding process and laser remelting carried out on austenitic stainless steel type X10CrNi18-8. Investigations were done by using an Ultra Nanoindentation Tester (UNHT) in the Warsaw Institute of Fundamental Technological Research. The influence of the above mentioned...
-
INFLUENCE OF MEASURING CONDITIONS ON TYRE/ROAD NOISE
PublicationA decisive factor for the development of tyres and road surfaces is the ability to conduct representative and reproducible measurements of selected characteristics related to the interaction of tyres and road surfaces. In terms of tyre/road noise measurements in Europe two methods described in ISO/FDIS 11819-2 and ECE Regulation No.117 are used. The latter is compulsory for assigning the tyre noise labels. The methodologies differ...
-
INFLUENCE OF LOAD AND INFLATION PRESSURE ON THE TYRE ROLLING RESISTANCE
PublicationTyre load and inflation pressure are important factors controlling rolling resistance of road vehicles. The article presents results obtained in the Technical University of Gdańsk during laboratory and road measurements of different car tyres rolling on different pavements. The knowledge of rolling resistance characteristics is important for modelling car dynamics as well as fuel consumption. It is also necessary to establish proper...
-
Influence of laser processing of the low alloy medium carbon structural steel on the development of the fatigue crack
PublicationThe paper contains the results of the structural analysis, hardness tests and fatigue tests conducted for the medium carbon structural steel with low content of Cr and Ni after its processing with CO2 laser beam. Pre-cracks were made in the round compact tension (RCT) specimen used for fatigue test. Next, four paths, parallel to each other, were melted on both sides of the samples using a laser beam. The paths were perpendicular...
-
Electrochemically assisted deposition of hydroxyapatite on Ti6Al4V substrates covered by CVD diamond films — Coating characterization and first cell biological results
PublicationAlthough titaniumand its alloys are widely used as implant material for orthopedic and dental applications they show only limited corrosion stability and osseointegration in different cases. The aim of the presented research was to develop and characterize a novel surface modification system from a thin diamond base layer and a hydroxyapatite (HAp) top coating deposited on the alloy Ti6Al4V widely used for implants in contact with bone....
-
Ekspertyza dotycząca przyczyn uszkodzenia śruby M30x125
PublicationWykonano badania przyczyn pęknięcia śruby M30x125 w warunkach eksploatacji
-
Ekspertyza dotycząca identyfikacji materiału uchwytów martwej kotwicy
PublicationWykonano badania identyfikacyjne materiału uchwytów kotwicy martwej
-
EFFECT OF SURFACE STATE AND STRESS ON AN OXIDATION OF THE ZIRCALOY-2 ALLOY
PublicationZr alloys are widely used as materials for nuclear fuel pellets in the nuclear industry. In the case of the LOCA or RIA happen, a temperature may locally reach high values. Even if the high temperature maintains shortly, the zirconium oxides may become permeable, absorb hydrogen appearing in cooling water from decomposition reaction and crack because of formation and brittle failure of hydrides. Such model cannot so far take into...
-
Effect of Semiconductor Element Substitution on the Electric Properties of Barium Titanate Ceramics
PublicationThe investigated ceramics were prepared by a solid-state reaction from simple oxides and carbonates with the use of a mixed oxide method (MOM). The morphology of BaTi0.96Si0.04O3 (BTSi04) ceramics was characterised by means of a scanning electron microscopy (SEM). It was found that Si+4 ion substitution supported the grain growth process in BT-based ceramics. The EDS results confirmed the high purity and expected quantitative composition...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublicationThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
Crystal structure and physical properties of new Ca2TGe3 (T = Pd and Pt) germanides
PublicationThe crystallographic, electronic transport and thermal properties of Ca2PdGe3 and Ca2PtGe3 are reported. The compounds crystalize in an ordered variant of the AlB2 crystal structure, in space group P6/mmm, with the lattice parameters a = 8.4876(4) Å/8.4503(5) Å and c = 4.1911(3) Å/4.2302(3) Å for Ca2PdGe3 and Ca2PtGe3, respectively. The resistivity data exhibit metallic behavior with residual-resistivity-ratios (RRR) of 13 for...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublicationThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Badanie wpływu zmian natężenia prądu na spawanie stopu aluminium
PublicationStop aluminium AW-7075 zyskuje coraz większą popularność w zastosowaniach komercyjnych ze względu na jego wyjątkowe właściwości fizyczne i mechaniczne: małą gęstość, wysoką wytrzymałość, udarność i plastyczność, bardzo dużą odporność na zmęczenie i zadowalającą na korozję, łatwą obrabialność i przetwarzalność. Ze względu na te właściwości, stop ten (AlZn5,5MgCu), zwany też FORTAL-em, używany jest dla części narażonych na wysokie...
-
Badania stanu technicznego ścianek szczelnych strony południowej i północnej komory południowej śluzy Dzierżno
PublicationPrace dotyczyły badań nieniszczących łączników (zamków) Paine`a oraz ścianek szczelnych. Ściany boczne komory południowej śluzy Dzierżno zbudowane są ze stalowych pasów blachy o grubości około 16mm i długości 22m połączonych ze sobą wzdłuż dłuższej krawędzi za pomocą zamków Peine`a. System ten umożliwia uzyskanie szczelnego połączenia na całej długości ścianki. Zaawansowany proces korozji spowodował rozszczelnienie połączenia...
-
Badania skłonności do pękania zimnego złączy doczołowych ze stali typu dupleks 2205 wykonanych w środowisku wodnym
PublicationW pracy zbadano skłonność stali dupleks 2205 do tworzenia pęknięć zimnych. Wykonano technologiczne próby Tekken w warunkach podwodnych metodą mokrą z wykorzystaniem elektrod otulonych. Przedstawiono wyniki badań twardości, badań metalograficzny makro i mikroskopowych oraz badań zawartości ferrytu.
-
Bacterial nanocellulose as a microbiological derived nanomaterial
PublicationBacterial nanocellulose (BNC) is a nanofibrilar polymer produced by strains such as Gluconacetobacter xylinus, one of the best bacterial species which given the highest efficiency in cellulose production. Bacterial cellulose is a biomaterial having unique properties such as: chemical purity, good mechanical strength, high flexibility, high absorbency, possibility of forming any shape and size and many others. Such a large number...
-
Assessment of hydrogenation of deposited metal of P 62 MR covered electrodes
PublicationThe determination of diffusible hydrogen content in deposited metal of P 62 MR covered electrodes for manual metal arc welding by mercury method was carried out. The test results indicate that covered electrodes 62 P MR grade generate a mean of 4.02 ml/100g of diffusible hydrogen in deposited metal, which is consistent with H5 class.
-
As causas do trincamento a frio de um ação submetido a soldagem subaquática
PublicationA soldagem subaquàtica usada na confeccao de juntas de acos de alta resistencia aumenta a sua susceptibilidade ao trincamento a frio, um efeito decorrente da transferencia de calor muito mais rapida a partir da area de soldagem e da presenca de hidrogenio difusivel, o que causa aumento da fragilidade do metal. Este trabalho avalia esta propensao ao trincamento a frio do aco S355G10+N usado na construcao de estrururas hidrotecnicas...
-
Antimicrobal and ostheointegration activity of bone cement contains nanometals
PublicationPurpose: One of the major problems in bone surgery are infections – especially thoseoccurring in the course of the operating on the patients with lowered immunity system,because they carry the danger of complications. In the Mechanical Department of TechnicalUniversity of Gdansk, there has been carried the research with the use of bone cement andmetal nanoparticles.Design/methodology/approach: The bone cement was used without supplement...
-
Analiza technologii lutowania próżniowego stali austenitycznej
PublicationCelem badań była ocena poprawności budowy złącza lutowanego próżniowo ze stali austenitycznej oraz analiza składu chemicznego charakterystycznych obszarów badanej próbki. Na podstawie badań wizualnych oraz metalograficznych na mikroskopie skaningowym (w tym analizy EDS) stwierdzono, że badane złącze charakteryzuje się prawidłową geometrią, jednak występują w nim liczne niezgodności (wydzielenia), co świadczy o nieprawidłowych parametrach...