Publications
Filters
total: 846
Catalog Publications
Year 2023
-
Reliability estimation of underground horizontal fuel tank limit states
PublicationFuel tanks are designed with regard to standard loads and operating conditions. The investigations of the paper show the impact of such factors as tank corrosion and other means on the variation of stress fields and deformation of the underground horizontal tank shell. The introduction of probabilistic methods allows for structural reliability assessment. While the computational time of the entire tank FEM model is high, the preliminary...
-
Removal of Arsenic from Wastewater Using Hydrochar Prepared from Red Macroalgae: Investigating Its Adsorption Efficiency and Mechanism
PublicationArsenic (As) is a prominent carcinogen component produced via both geogenic and anthropogenic processes, posing serious risks to human health. This study aimed to investigate the potential of hydrochar prepared from red macroalgae for removing As from synthetic wastewater. The hydrochar was produced through 5 h hydrothermal carbonization (HTC) treatment at 200 °C, and then, chemically activated with ferric chloride hexahydrate...
-
Resource productivity and environmental degradation in EU-27 countries: context of material footprint
PublicationThis study explores the relationship between the resource productivity and environmental degradation in European Union-27 countries. This study tests this relationship in context of high, moderate, and low material footprint sub-samples; these samples are formed utilizing the expectation–maximization machine learning algorithm. Using the panel data set of EU-27 countries from 2000 to 2020, linear and non-linear autoregressive distributed...
-
Rethinking non-governmental organizations – at the crossroad of economics and civil society
PublicationThe article aims to close the existing knowledge gaps, show why non‑governmental organizations are founded and maintained, and elaborate and systematize the existing knowledge through an analysis of the existing subdisciplines within economics, laying the groundwork for the economics of non‑governmental organizations. The article was written based on a structured literature review with an approach similar to the grounded theory...
-
RF Multi-Functional Input-Reflectionless Dispersive-Delay Structure With Sharp-Rejection Filtering Using Channelization Techniques
PublicationA class of RF multi-functional input-reflectionless dispersive-delay structure (DDS) with linear-type in-band groupdelay variation and sharp-rejection bandpass-filtering capability is reported. It exploits a two-branch-channelized/balanced-type circuit with similar low-order reflective DDS units inside its channels, which are connected through input/output 3-dB quadrature wideband couplers. The adopted DDS unit is based on a coupledresonator...
-
Rubber wastes recycling for developing advanced polymer composites: A warm handshake with sustainability
PublicationRecycling and management of rubber wastes experiences an early-stage maturity in the quest for sustainable and circular materials. Up to now, solutions proposed for sustainable development of rubber wastes are limited, so that properties and performance features of recycled products are inadequate for practical applications. Herein, an experimental protocol is introduced for manufacturing semi-sustainable polymer composites based...
-
Scrutiny of power grids by penetrating PV energy in wind farms: a case study of the wind corridor of Jhampir, Pakistan
PublicationThis study examines the problems caused by intermittent renewable energy sources, especially wind farms, and suggests a different solar energy penetration strategy to improve their loading capacity. The study uses real-time data from a wind farm in Jhampir, Pakistan, to analyse and assess various aspects of grid stations connected to wind farms. Electrical Transient Analyzer Program is used to validate the results by linking these...
-
Seismic performance evaluation of steel buckling-restrained braced frames including SMA materials
PublicationThe permanent deformation of the building after seismic excitations can be determined by the Maximum Residual Interstory Drift Ratio (MR-IDR), which may be used for measuring the damage states. Low-post yield stiffness of the steel buckling-restrained braced frame (BRBF) makes this system vulnerable to large MR-IDR after a severe earthquake event. To overcome this issue, this paper investigates the seismic limit state performances...
-
Self-Adaptive Mesh Generator for Global Complex Roots and Poles Finding Algorithm
PublicationIn any global method of searching for roots and poles, increasing the number of samples increases the chances of finding them precisely in a given area. However, the global complex roots and poles finding algorithm (GRPF) (as one of the few) has direct control over the accuracy of the results. In addition, this algorithm has a simple condition for finding all roots and poles in a given area: it only requires a sufficiently dense...
-
Sequential treatment of landfill leachate by electrocoagulation/aeration, PMS/ZVI/UV and electro-Fenton: Performance, biodegradability and toxicity studies
PublicationThis study presents a systematic study on sequential treatment of highly resistant landfill leachate by electrocoagulation (EC)/aeration, sulfate radical advanced oxidation process (SR-AOP) and electro-Fenton (EF). In case of SR-AOP, peroxymonosulfate (PMS) catalyzed by zero valent iron (ZVI) and ultraviolet irradiation (UV) system was developed. Treatment process was optimized in respect to COD removal. Analysis of results revealed...
-
Silver(I) complexes with nitrile ligands: New materials with versatile applications
PublicationIn the present study, the structure, thermal stability, conductive properties, and antimicrobial activity of silver(I) complexes with nitrile ligands were investigated. For the construction of the materials, 2-cyanopyridine (2-cpy), 4-cyanopyridine (4-cpy), 1,2-dicyanobenzene (1,2-dcb), and 1,3-dicyanobenzene (1,3-dcb) were used in addition to the silver nitrite and nitrate. Four new compounds were isolated and structurally characterized:...
-
Solar light driven degradation of textile dye contaminants for wastewater treatment – studies of novel polycationic selenide photocatalyst and process optimization by response surface methodology desirability factor
PublicationThe unplanned anthropogenic activities and raced industrial revolution detrimentally causes serious threat to terrestrial and aquatic life. A high discharge of wastewater from industries using dyes affects living organisms and the environment. This paper presents studies on polycationic selenides (PCS) synthesized by hydrothermal methods for photocatalytic degradation of dyes. The synthesized PCS were confirmed by various characterization...
-
Spatio-Temporal Validation of GNSS-Derived Global Ionosphere Maps Using 16 Years of Jason Satellites Observations
PublicationExisting ionospheric models perform very well in mapping the calm state of the ionosphere. However, the problem is accurately determining the total electron content (TEC) for disturbed days. Knowledge of the exact electron density is essential for single−frequency receivers, which cannot eliminate the ionospheric delay. This study aims to investigate temporal and spatial variability in the distribution of TEC based on differences...
-
Spike patterns and chaos in a map-based neuron model
PublicationThe work studies the well-known map-based model of neuronal dynamics introduced in 2007 by Courbage, Nekorkin and Vdovin, important due to various medical applications. We also review and extend some of the existing results concerning β-transformations and (expanding) Lorenz mappings. Then we apply them for deducing important properties of spike-trains generated by the CNV model and explain their implications for neuron behaviour....
-
Stability Enhancement of Grid-Connected Wind Power Generation System Using PSS, SFCL and STATCOM
PublicationThe stability related issues may occur in a power system due to disturbances in generating or loading conditions, especially in the presence of distributed generation (DG) based on renewable energy resources (RERs). This paper proposes a novel strategy for the stability enhancement of a wind power generation system (WPGS) by using a combination of three devices, namely, a power system stabilizer (PSS), resistive superconductor...
-
Static Shape and Stress Control of Trusses with Optimum Time, Actuators and Actuation
PublicationTraditional shape and stress control of structures use many actuators and require enormous time to find reasonable solutions that need designers to input specific target displacement and stress. This study employs a linear technique to static shape and stress control of pin-jointed assemblies as a theoretical advancement to prior works and provides a comparative analysis against previously established works. The study evaluates...
-
Structural and luminescence properties of B2O3-Bi2O3-AlF3 glass doped with Eu3+, Tb3+ and Tm3+ ions
PublicationThe B2O3-Bi2O3-AlF3 glass system doped with Eu3+, Tb3+, Tm3+ and triply doped with Eu3+/Tm3+/Tb3+ ions in different molar ratios were successfully synthesized. Glass transition and crystallization temperatures were examined by Differential Scanning Calorimetry (DSC) measurements. X-ray Diffraction (XRD) confirmed the amorphous character of the samples. Fourier Transform Infrared Spectroscopy (FTIR) revealed that the glass matrix...
-
Structurally well-defined functionalized polyolefins and graft copolymers thereof as bitumen modifiers
PublicationHere we demonstrate the application of hydroxyl-functionalized propylene-based copolymers, poly(propylene-co-1-hexene-co-10-undecen-1-ol) (FPP) and poly(styrene-co-maleic anhydride) (SMA) graft copolymers derived thereof, poly(propylene-co-1- hexene-graft-styrene-co-maleic anhydride) (FPP-g-SMA) as bitumen modifiers. The FPP samples were synthesized via solution copolymerization, while FPP-g-SMA products were obtained via transesterification...
-
Structure-Property Relationship and Multiple Processing Studies of Novel Bio-Based Thermoplastic Polyurethane Elastomers
PublicationCurrently, the growing demand for polymeric materials has led to an increased need to develop effective recycling methods. This study focuses on the multiple processing of bio-based thermoplastic polyurethane elastomers (bio-TPUs) as a sustainable approach for polymeric waste management through mechanical recycling. The main objective is to investigate the influence of two reprocessing cycles on selected properties of bio-TPUs....
-
Study of ZrS3-based field-effect transistors toward the understanding of the mechanisms of light-enhanced gas sensing by transition metal trichalcogenides
PublicationExtending knowledge of the properties of low-dimensional van der Waals materials, including their reactivity to the ambiance, is important for developing innovative electronic and optoelectronic devices. Transition metal trichalcogenides with tunable optical band gaps and anisotropic conductivity are an emerging class among low- dimensional structures with the possibility of gate tunability and photoreactivity. These properties...
-
Study on effective front region thickness of PCM in thermal energy storage using a novel semi-theoretical model
PublicationThermal energy storage in mobile applications, particularly battery of electric vehicles, is currently gaining a lot of importance. In this paper, a semi-theoretical time-dependent mathematical model of the phase change in a double shell thermal energy storage module has been developed where the inner tube is a heat exchange surface. An effective front region thickness for the melting and solidification process has been studied....
-
Suppressors of lapC mutation identify new regulators of LpxC, which mediates the first committed step in lipopolysaccharide biosynthesis
PublicationGram-negative bacteria, such as Escherichia coli, are characterized by an asymmetric outer membrane (OM) with lipopolysaccharide (LPS) located in the outer leaflet and phospholipids facing the inner leaflet. E. coli recruits LPS assembly proteins LapB, LapC and LapD in concert with FtsH protease to ensure a balanced biosynthesis of LPS and phospholipids. We recently reported that bacteria either lacking the periplasmic domain of...
-
Suspended-sediment transport related to ice-cover conditions during cold and warm winters, Toudaoguai stretch of the Yellow River, Inner Mongolia, China
PublicationThe presence of winter ice in cold regions changes the water level, flow rate, velocity distribution, and other parameters of the river, which in turn affects the sediment concentration and channel evolution. Based on data obtained from Toudaoguai Hydrological Station from 1959 to 2021, this study examines the characteristics of the ice regime during cold and warm winters and the water and sediment transport processes along the...
-
Sustainable polymers targeted at the surgical and otolaryngological applications: Circularity and future
PublicationThe ongoing climate changes, high air and noise pollution have significant impact on humans’ health. This influence is especially visible in otolaryngology, which focuses on respiratory and hearing systems disfunctions. However, even though surgeries are done in response to diseases related to climate changes, they also have a negative impact on the environment, mostly connected with the inherence of single-use fossil fuel derived...
-
Sustainable utilization of copper post-flotation waste in cement composites
PublicationThe current way of managing the copper ore flotation waste is by placing it in waste neutralization facilities. However, flotation waste has great potential in application in cement composites. The article presents the detailed characteristics of post-flotation waste (PFW) and three types of cements: CEM I, CEM II/B-V, and CEM III/A, 42.5 MPa class. The post-flotation waste added for 20% of the cement mass increase the water demand...
-
Tailoring diamondised nanocarbon-loaded poly(lactic acid) composites for highly electroactive surfaces: extrusion and characterisation of filaments for improved 3D-printed surfaces
PublicationA new 3D-printable composite has been developed dedicated to electroanalytical applications. Two types of diamondised nanocarbons - detonation nanodiamonds (DNDs) and boron-doped carbon nanowalls (BCNWs) - were added as fillers in poly(lactic acid) (PLA)-based composites to extrude 3D filaments. Carbon black served as a primary filler to reach high composite conductivity at low diamondised nanocarbon concentrations (0.01 to 0.2...
-
Tailoring optical constants of few-layer black phosphorus coatings: Spectroscopic ellipsometry approach supported by ab-initio simulation
Publication2D black phosphorus (BP) has attracted extensive attention as an anisotropic platform for novel optoelectronic and polarizing optics applications. Insight into the factors that tune the optical and polarizing properties of 2D BP reveals their essential influence on BP-based photonic and optoelectronic devices. In this work, studies of the optical constants of few-layer black phosphorus coatings are studied and discussed, with particular...
-
Targeting Spike‐ACE2 Interface of SARS‐CoV‐2 and its Omicron Variant: A Comparative Screening of Potential Inhibitors for Existing and Anticipating Variants Using Molecular Modelling Approach
PublicationThe recent COVID pandemic has shown major impact on public health and economic crisis. Despite the development of many vaccines and drugs against the severe acute respiratory syndrome (SARS) coronavirus 2, the pandemic still persists. The continued spread of the virus is largely driven by the emergence of viral variants such as α, β, γ, delta, epsilon spike, omicron and its subvariants (BA.1,2,3) which can evade the current vaccines...
-
Techno-economic assessment of cooperation of hybrid renewable energy sources with hydrogen storage
PublicationThe paper presents a technical and economic analysis of the power supply for a model industrial facility with the use of the most promising renewable energy sources (RES), supported by a hydrogen energy storage. This scenario was compared with the variants of supplying the facility directly from the grid and from RES without energy storage. A strategy was proposed for powering the plant aimed at maximising self-consumption of self-generated...
-
Telomerase inhibition - unfulfilled hopes in the perfect molecular target
PublicationTelomerase plays a pivotal role in cell proliferation, homeostasis, and neoplastic transformation, making it a promising molecular target for cancer chemotherapy. Of note, although hTERT has been explored thoroughly as a target, none of the promising molecules has been approved as a drug until now. The subject of research conducted as part of my doctoral dissertation is explaining the cellular and molecular mechanism of action...
-
The accessibility, necessity, and significance of certified reference materials for total selenium content and its species to improve food laboratories' performance
PublicationMicronutrients are one of the most important groups of nutrients that our body needs daily in trace amounts to tackle deficiencies. Selenium (Se) is a mineral that occurs naturally in foods and is an essential component of selenoproteins that support the healthy functioning of the human body. Therefore, monitoring dietary Se concentrations must be a higher priority to meet daily intakes. Fulfillment can be addressed through applying...
-
The Design of Cavity Resonators and Microwave Filters Applying Shape Deformation Techniques
PublicationThis article introduces shape deformation as a new approach to the computer-aided design (CAD) of high-frequency components. We show that geometry deformation opens up new design possibilities and offers additional degrees of freedom in the 3-D modeling of microwave structures. Such design flexibility is highly desirable if the full potential of additive manufacturing (AM) is to be exploited in the fabrication of RF and microwave...
-
The Effect of Titanium Oxyfluoride Morphology on Photocatalytic Activity of Fluorine-Doped Titanium(IV) Oxide
PublicationTitanium oxyfluoride (TiOF2) is a metastable product that can be obtained in a fluorine-rich environment. This material can also be a valuable precursor in the synthesis of titanium(IV) oxide (TiO2). However, the effect of TiOF2 morphology on the physicochemical properties of TiO2 has not been studied so far. In this work, single-phase TiOF2 was prepared by a solvothermal method. The as-synthesized samples exhibited a variety of...
-
The effects of gas exposure on the graphene/AlGaN/GaN heterostructure under UV irradiation
PublicationThis work demonstrates a graphene/AlGaN/GaN sensing device with two-dimensional electron gas (2DEG) toward nitrogen dioxide (NO2), tetrahydrofuran, and acetone detection under UV light irradiation. We propose combining measurements of the DC characteristics with a fluctuation-enhanced sensing method to provide insight into the gas detection mechanisms in the synergistic structure of highly stable GaN and gas-sensitive graphene....
-
The impact of filler thermomechanical modifications on static and dynamic mechanical performance of flexible foamed polyurethane/ground tire rubber/zinc borate composites
PublicationThe rapid development of the automotive industry is very beneficial to many aspects of human life, but it is also a very significant environmental burden. The most straightforward impact is related to the generation of exhaust, but the management of post-consumer car parts is also a major challenge. Among them, waste tires are very burdensome due to their enormous numbers. Therefore, it is essential to develop novel, environmentally...
-
The impact of hydrological research, municipal authorities, and residents on rainwater management in Gdańsk (Poland) in the process of adapting the city to climate change
PublicationAim of the study The city of Gdańsk faces changing climatic conditions that result in a higher frequency of extreme weather events. In response to the increasingly frequent appearance of flash floods, scientific research was carried out on changes in the probability of the occurrence of maximum daily precipitation in Gdańsk. The purpose of this paper is to show the role of hydrological research (science), decisions of local authorities...
-
The interactions of monomeric acridines and unsymmetrical bisacridines (UAs) with DNA duplexes: an insight provided by NMR and MD studies
PublicationMembers of a novel class of anticancer compounds, exhibiting high antitumor activity, i.e. the unsymmetrical bisacridines (UAs), consist of two heteroaromatic ring systems. One of the ring systems is an imidazoacridinone moiety, with the skeleton identical to the structural base of Symadex. The second one is a 1-nitroacridine moiety, hence it may be regarded as Nitracrine’s structural basis. These monoacridine units are connected...
-
The new method of ZnIn2S4 synthesis on the titania nanotubes substrate with enhanced stability and photoelectrochemical performance
PublicationThe new method of ZnIn2S4 synthesis on the titania nanotubes substrate with enhanced stability and photoelectrochemical performance
-
The Physiological Effects of ASMR on Anxiety
PublicationPurpose: Autonomous Sensory Meridian Response is a novel phenomenon that is very popular these days on Youtube and Reddit to its anti-anxiety effects. As the name suggests, ASMR is a relaxing warm sensation that begins on the scalp and spreads throughout the body. This technique is also known as "brain massage," and it relies on soothing sights and sounds, like whispers and slow movements. Investigating these videos is primarily motivated...
-
The role of sport in the Smart City concept
PublicationSport brings to cities innovative solutions that influence urban life, yet considerations about sport still rarely contribute to the development of the very popular smart city concept. This raises the question: what is the perception of sport in the city from the perspective of the smart city concept? One of the challenges of future urban policy is to provide initiatives that ensure the wellbeing and promote the model of a healthy...
-
Therapeutic biomaterials - application in neurology and cardiology
PublicationBiomaterials are of interest in most medical fields. It's hard to imagine life without them. And due to the ever-increasing demand, scientists are developing new materials. Diseases of the nervous and cardiovascular systems are still a big problem, which are associated with a limited ability to regenerate brain or heart tissues. Therefore, this review discusses the advancement in biomaterial engineering for the treatment of neurological...
-
Thermal Instability of Gold Thin Films
PublicationThe disintegration of a continuous metallic thin film leads to the formation of isolated islands, which can be used for the preparation of plasmonic structures. The transformation mechanism is driven by a thermally accelerated diffusion that leads to the minimalization of surface free energy in the system. In this paper, we report the results of our study on the disintegration of gold thin film and the formation of nanoislands...
-
ThreSpect – A Program for the Determination of the Appearance Energies of Neutral and Ionized Species
PublicationCollisions of photons and charged particles with molecules lead to their excitation, ionization, and dissociation into neutral and ionized fragments. Accurately determining thresholds of the formation of particular products plays a vital role in analyzing processes occurring during these interactions. Therefore, we present a computer program, “ThreSpect,” that allows calculating threshold energies of various species generated in...
-
Ti-Fe2O3/In2O3 as photoactive material: The role of the substrate in photoelectrochemical water oxidation
PublicationThe layers of Ti-Fe2O3/In2O3 were prepared on the different substrates using hydrothermal method: Ti/TiO2 nanotubes, Ti foil, FTO and FTO/TiO2. Materials were characterized using scanning electron microscopy, XRD, Raman, UV-Vis, and X-ray photoelectron spectroscopy and tested as photoanodes for water oxidation under illumination. The formation of heterojunction on the TiO2 nanotubes increases photocurrent of water oxidation at...
-
Time series analysis and impact assessment of the temperature changes on the vegetation and the water availability: A case study of Bakun-Murum Catchment Region in Malaysia
PublicationThe Bakun-Murum (BM) catchment region of the Rajang River Basin (RRB), Sarawak, Malaysia, has been under severe threat for the last few years due to urbanization, global warming, and climate change. The present study aimed to evaluate the time series analysis and impact assessment of the temperature changes on the vegetation/agricultural lands and the water availability within the BM region. For this purpose, the Landsat data for...
-
Tuning of eg electron occupancy of MnCo2O4 spinel for oxygen evolution reaction by partial substitution of Co by Fe at octahedral sites
PublicationTo study the effect of partial Co substitution by Fe in the B site of MnCo2O4 spinel on its physicochemical and electrochemical properties, a series of MnCo2-xFexO4 powders (x=0.125; 0.250; 0.500; 0.750; 1.000) were synthesized by means of the sol-gel method. The produced powders were characterized by powder X ray diffraction (pXRD), scanning and transmission electron microscopy (SEM & TEM) coupled with energy dispersive spectroscopy...
-
Ultrasound assisted dispersive solid phase microextraction using polystyrene-polyoleic acid graft copolymer for determination of Sb(III) in various bottled beverages by HGAAS
PublicationA new polyoleic acid-polystyrene (PoleS) block/graft copolymer was synthesized and applied as adsorbent for ultrasound assisted dispersive solid phase microextraction (UA-DSPME) of Sb(III) in different bottled beverages and analysis using hydride generation atomic absorption spectrometry (HGAAS). Adsorption capacity of the PoleS was 150 mg g−1. Several sample preparation parameters such as sorbent amount, solvent type, pH, sample...
-
Vascular stents - materials and manufacturing technologies
PublicationThe objective of this article is to present materials and technology for the manufacture of vascular stents with appropriate design requirements. The use of the right material is very important in implantology. A biomaterial introduced into the circulatory system must be biocompatible and hemocompatible. At the same time, it should not initiate toxic, mutagenic, or immunological reactions. Currently, 316L stainless steel (316L...
-
Waste printer ink as modifier for natural rubber/carbon black composites: No haste, use waste
PublicationFrom a sustainability perspective, achieving a greener future with a minimal carbon footprint requires maximizing waste materials' reuse. The four pillars of satisfying customer demands are processing, price, properties, and performance. Along with such a global policy, this work seeks to utilize waste printer ink (WPI) as a source of carbon in combination with low- and high-surface carbon black (LCB and HCB, respectively) additives...
-
Water uptake kinetics and electrical transport in BaCe0.6Zr0.2Y0.1M0.1O3−δ (M = Tb, Pr, Fe) protonic conductors
PublicationBaCe0.6Zr0.2Y0.1M0.1O3−d (M = Fe, Pr, Tb) is a mixed conducting oxide in which three mobile charge carriers – oxygen ion, electron/hole, and protonic defects – are present. These types of materials have gained much interest as electrode materials for protonic ceramic fuel cells (PCFCs) and protonic ceramic electrolysis cells (PCECs). In this study, the water uptake and oxygen transport properties of different BaCe0.6Zr0.2Y0.1M0.1O3−d...