Search
Division Of Materials Science And Technology
Publications
Filters
total: 292
Catalog Publications
Year 2018
-
A universal NDT method for examination of low energy impact damage in CFRP with the use of TLC film
PublicationThe article presents an attempt to use a sheet of laminated thermochromic liquid crystal film (TLC film) for non-destructive testing of the impact damage (energy values: 1J, 2J, 3J and 4J) in carbon fibre-reinforced polymer (CFRP). This is a new, alternative NDT approach based on the thermo-optical effect. The main advantages of this method are a) the low cost of TLC film, b) the low cost of recording devices due to the usage of...
-
Biopolyols obtained via microwave-assisted liquefaction of lignin: structure, rheological, physical and thermal properties
PublicationThe present study examined the application of polyols obtained via microwave-assisted liquefaction of lignin in the production of rigid polyurethane foam. Lignin was liquefed in crude glycerol and 1,4-butanediol at diferent temperatures (130–170 °C), without a catalyst and using various biomass concentrations (15 and 30 wt%). The physicochemical properties, process yield, and FTIR-based identifcation of the obtained polyols were...
-
Ekspertyza przyczyn pęknięcia rurociągu w instalacji 016-P1365
PublicationWykonano badania przyczyn pęknięcia złącza wzmocnienia i rurociągu w instalacji 016-P1365. Ustalono prawdopodobną przyczynę pękania.
-
Impact resistance of plain and twill fabric in GFRP measured by active thermography
PublicationThis paper discusses the impact resistance of glass-fibre reinforced polymer (GFRP) composites depending on the type of reinforcement – plain or twill weave. The values of impact energy were: 3J, 10J and 15J. Specimens featuring twill weave transferred higher force during the impact as compared with plain weave specimens. It was observed that an increase of impact energy was accompanied by an increase of the disproportion in...
-
Influence of dopants on structure of polycrystalline bismuth niobate
PublicationBismuth niobate (BiNbO4) has attracted attention as a low-fired ceramics with promising microwave application potential. BiNbO4 ceramics was fabricated by mixed oxide method and sintered at temperature T<1000˚C. As the sintering aids a small amount of CuO oxide was used. The crystalline structure of the ceramic samples was examined by X-ray diffraction method at room temperature. The Rietveld refinement method was used for analysis...
-
Influence of parameters of deep grinding on nanohardness and surface roughness of C45 steel
PublicationPrzedstawiono wyniki badań wpływu głębokości współbieżnego szlifowania powierzchni płaskich na chropowatość i nanotwardość warstwy wierzchniej stali C45 o strukturze ferrytyczno-perlitycznej i średniej wielkości ziarna 20 μm. Dla wszystkich wartości głębokości szlifowania uzyskano znaczny wzrost twardości warstwy wierzchniej przedmiotu obrabianego.
-
Laboratory research on the influence of swelling clay on the quality of borehole cementing and evaluation of clay-cutting wellbore tool prototype
PublicationSwelling clay phenomenon is frequently observed during oil and gas drilling operations and has a significant impact on the quality of cementing procedure. Certain types of clayey minerals increase their volume in contact with water-based drilling fluids. After drilling is completed, borehole remains unsupported and filled with waterbased drilling fluids for several hours, before a casing string is inserted and secured with cement....
-
Nanotubular oxide layers and hydroxyapatite coatings on porous titanium alloy Ti13Nb13Zr
PublicationThe surface condition of an implant has a significant impact on response occurring at the implant-biosystem border. The knowledge of physical-chemical and biological processes allows for targeted modification of biomaterials to induce a specified response of a tissue. The present research was aimed at development of technology composing of obtaining the nanotube oxide layers on a porous titanium alloy Ti13Nb13Zr, followed by the...
-
Opinia dotycząca jakości wykonania elementów balustrad przystanków PKM oraz możliwych przyczyn występowania korozji
PublicationSporządzono opinię dotycząca występowania korozji elementów konstrukcyjnych balustrad na przystankach kolei PKM. Wskazano możliwe przyczyny korozji.
-
Opinia dotycząca zaworów firmy ARCO oraz "Duro" i "Calido" firmy Arka z/s w Siaowie
PublicationWykonano analizy składu chemicznego materiałów badanych zaworów celem stwierdzenia występowania pierwiastków niezgodnych z wymaganiami normy.
-
Opracowanie opinii na temat własności materiału podstawowego oraz jakości spoin kotła typu KSBS 380 nr fabryczny 117
PublicationNiniejsza opinia przedstawia odpowiedzi na pytania Sądu wyrażone w w/w postanowieniu, a mianowicie czy zastosowane materiały do produkcji przedmiotowego kotła jak również jakość spoin była przyczyną awarii kotła w dniu 25.12.2014r, w tym również porównanie uzyskanych wyników badań z dokumentacją konstrukcyjna kotła.2. Połączenia spawane w badanej konstrukcji kotła były najsłabszym elementem konstrukcyjnym, w którym na skutek...
-
Oxidation and hydrogen behavior in Zr-2Mn alloy
PublicationThe purpose of the present research was to determine the oxidation and hydrogenation behavior in the new Zr-2Mn alloy. The oxidation of alloy was performed at temperatures between 350°C and 900°C for 30 minutes. The hydrogen charging was made for 72 h at a current density 80 mA/cm2. The charged samples were heat treated at 400°C for 4 h to obtain a uniform hydrogen profile content across the sample. The oxidation resulted in an...
-
Selection of material for X-ray tomography analysis and DEM simulations: comparison between granular materials of biological and non-biological origins
PublicationPhysical properties and X-ray tomography images of five different granular materials: glass bead, glass grit, short grain white rice, sorghum and clay granules (Seramis) are investigated to select the most promising materials for numerical simulations and time-lapse X-ray tomography imaging. The examined materials represent granular materials of non-biological origin (glass bead, glass grit and Seramis) and granular plant materials...
-
Structural and mechanical properties of hydroxyapatite coatings formed by ion-beam assisted deposition
PublicationThe ion-beam assisted deposition (IBAD) is an advanced method capable of producing crystalline coatings at low temperatures. We determined the characteristics of hydroxyapatite Ca10(PO4)6(OH)2 target and coatings formed by IBAD using X-ray photoemission spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and energy dispersive X-ray (EDX). The composition of the coatings'...
-
Studies on Silver Ions Releasing Processes and Mechanical Properties of Surface-Modified Titanium Alloy Implants
PublicationDispersed silver nanoparticles (AgNPs) on the surface of titanium alloy (Ti6Al4V) and titanium alloy modified by titania nanotube layer (Ti6Al4V/TNT) substrates were produced by the chemical vapor deposition method (CVD) using a novel precursor of the formula [Ag5(O2CC2F5)5(H2O)3]. The structure and volatile properties of this compound were determined using single crystal X-ray diffractometry, variable temperature IR spectrophotometry...
-
Study of the influence of thermal factors on the welding process of polyethylene gas pipelines,
PublicationA one-dimensional calculation scheme is proposed with the help of which it is possible to determine and set the technological parameters with the accuracy to be realized in production conditions: the temperature of the heating element and the heating time, which allows maximum mechanization of the technological operations of polyethylene gas pipelines welding. The numerical value of the coefficient of temperature for polyethylene...
-
Wpływ parametrów szlifowania wgłębnego na nanotwardość i chropowatość powierzchni stali C45
PublicationW artykule przedstawiono wyniki badań wpływu głębo-kości współbieżnego szlifowania powierzchni płaskich na chropowatość i nanotwardość warstwy wierzchniej stali C45 o strukturze ferrytyczno-perlitycznej i średniej wielkości ziarna 20 µm. Dla wszystkich wartości głębo-kości szlifowania uzyskano znaczny wzrost twardości warstwy wierzchniej przedmiotu obrabianego
Year 2017
-
Badania śrub kominów 250, 120, 270, 9800
PublicationPrzedmiotem pracy było wykonanie badań pękniętych śrub komina 250 oraz ustalanie przyczyn ich uszkodzenia. Przedmiotem drugiego zadania było wykonanie badań weryfikacyjnych śrub pobranych z połączeń kołnierzowych kominów 120, 270 i 9800.
-
Badanie wpływu zmiany składu gazów osłonowych na spawanie metodą MIG stopu aluminium EN AW 7075. Innowacyjne wykorzystanie w wiertnictwie.
PublicationStop aluminium AW-7075 zyskuje coraz większą popularność w zastosowaniach komercyjnych ze względu na jego wyjątkowe właściwości fizyczne i mechaniczne: małą gęstość, wysoką wytrzymałość, udarność i plastyczność, bardzo dużą odporność na zmęczenie i zadowalającą na korozję, łatwą obrabialność i przetwarzalność. Ze względu na te właściwości, stop ten (AlZn5,5MgCu), zwany też FORTAL-em, używany jest dla części narażonych na wysokie...
-
Cavitation erosion degradation of Belzona® coatings
PublicationIn hydrocarbon and maritime industry there is a constant need of materials and coatings withstanding severe conditions. One of adverse phenomena present there is cavitation erosion. The paper presents evaluation of cavitation resistance of three different steel coatings. Belzona 2141 (ACR-Fluid Elastormer), 1321 (Ceramic S-Steal) and 5831 (ST-Barrier) were deployed on P110 steel and subjected to ultrasound cavitation in distilled...
-
Corrosion degradation of spacers – examination of changes in bone cement coating.
PublicationSpacer is a special implant used at the time of infection after endoprosthetic surgery. It consists of a metal core and bone cement coating with an antibiotic. In the human body spacers are exposed to degradation processes. This paper looks at the effect of corrosion on spacers. Electrochemical corrosion tests were performer on titanium pins with bone cement coating in two solutions: Ringer’s solution and artificial...
-
Ekspertyza przyczyn uszkodzenia krzywek mocowania baterii wannowej
PublicationWykonano badania celem ustalenia przyczyn uszkodzenia krzywek do mocowania baterii wykonanych z mosiądzu. Jako przyczynę wskazano korozję międzykrystaliczną.
-
Ekspertyza przyczyn uszkodzenia zaworu kulowego 1/2"
PublicationWykonano badania przyczyn uszkodzenia zaworu kulowego wykonanego z mosiądzu. Jako przyczynę wskazano korozjęe naprężeniową.
-
Fabrication and Crystal Structure of Sol-Gel Deposited BST Thin Films with Compositional Gradient
PublicationIn the present research technology of compositionally graded barium strontium titanate Ba1-xSrxTiO3 thin films deposited on stainless steel substrates by sol-gel spin coating followed with thermal annealing at T = 650°C is reported. Results of thermal behavior of the sol-gel derived powders with compositions used for fabrication of graded structure (i.e. with Sr mole fraction x = 0.5, 0.4 and 0.3) are described. X-ray diffraction...
-
Hydrogen degradation of pre-oxidized zirconium alloys
PublicationThe presence of the oxide layers on Zr alloys may retard or enhance the hydrogen entry and material degradation, depending on the layer features. This research has been aimed to determine the effects of pre-oxidation of the Zircaloy-2 alloy at a different temperature on hydrogen degradation. The specimens were oxidised in laboratory air at 350°C, 700°C, and 900°C. After, some samples were tensed at 10-5 strain rate and simultaneously...
-
Improvement of microstructure and mechanical properties of high dense sic ceramics manufactured by high-speed hot pressing
PublicationNon-oxide ceramics possess high physical-mechanical properties, corrosion and radiation resistance, which can be used as a protective materials for radioactive wastes disposal. The aim of the present study was the manufacturing of high density SiC ceramics with advanced physical and mechanical parameters. The high performance on the properties of produced ceramics was determined by the dense and monolithic structure. The densified...
-
Influence of processing conditions on crystal structure of BiNbO 4 ceramics
PublicationBismuth niobate (BiNbO4) has attracted attention as a low-fired ceramics with promising microwave application potential. It belongs to the bismutocolumbite oxides with similarly to scheelite-like stibiotantalite structure (SbTaO4) A3+B5+O4. Aim of the present research was to fabricate BiNbO4 ceramics by solid state reaction route from the mixture of simple oxides viz. Bi2O3, and Nb2O5, and study its phase composition as well as...
-
MATCHED FILTER APPROACH FOR MICROSEISMIC SIGNAL PROCESSING OF REAL DATA FROM EAST POMERANIA SHALE GAS
PublicationThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing (HF)process. An array of several hundred geophones is placed on the surface to record little ground tremors induced by fracturing process. Filtration and summation of signals from geophones is essential to identify and locate fracturing events from underground. Authors propose a method of matched filtering, that is usually...
-
MICROSEISMIC EVENT DETECTION USING DIFFERENT ALGORITHMS ON REAL DATA FROM PATCH ARRAY GEOPHONE GRID FROM EASTERN POMERANIA FRACTURING JOB
PublicationThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing process. Hydraulic fracturing is a method of reservoir stimulation used especially for unconventional gas recovery. A matrix of several thousand geophones is placed on the surface of earth to record every little tremor of ground induced by fracturing process. Afterwards, the signal is analysed and the place of tremor occurrence...
-
Microseismic Monitoring of Hydraulic Fracturing - Data Interpretation Methodology With an Example from Pomerania
PublicationMicroseismic monitoring is a method for localizing fractures induced by hydraulic fracturing in search for shell gas. The data is collected from an array of geophones deployed on the surface or underground. Ground vibrations are recorded and analysed for fracture location, magnitude and breakage mechanism. For successful microseismic monitoring one need a velocity model of underlying formations. The model is further tuned with...
-
Ocena stanu technicznego kompensatorów wylotowych (pigtaili) rur katalitycznych z reformera 0250-F101
PublicationCelem badań było ustalenie stanu materiału rur kompensatorów wylotowych rur katalitycznych z reformera metanu po eksploatacji. Wykonano badania niszczących odcinków rur, analizę spektralną składu chemicznego, badania metalograficzne mikroskopowe, pomiary twardości i mikrotwardości, statyczne próby rozciągania w temperaturze pokojowej. Dokonano oceny stopnia degradacji materiału rur z orzeczeniem o aktualnym stanie technicznym kompensatorów.
-
Planning, Configuration and Usefulness of Microseismic Monitoring on Eastern-Europe Platform – Example from East Pomerania
PublicationThe microseismic monitoring is a method of monitoring of fracture propagation during hydraulic fracturing process. The method uses array of geophones to localize micro tremors induced by liquid pumped underground at high rate and pressure. The acquired information helps to optimize fracturing process and prevents fracture growth to aquifer levels. It proved to be useful on several unconventional hydrocarbon reservoirs in the USA....
-
Powierzchniowe badania mikrosejsmiczne na odwiercie w północnej Polsce, optymalizacja modelu prędkościowego
PublicationCelem wykonanych prac było potwierdzenie możliwości wykorzystania mikrosejsmicznego pomiaru powierzchniowego ze schematem rozłożenia typu patch array dla polskich warunków geologicznych. Artykuł zawiera opis przeprowadzonych prac mikrosejsmiki powierzchniowej wykonanych na odwiercie w północnej Polsce wraz z procedurą optymalizacji modelu prędkościowego.
-
Properties of Composite Oxide Layers on The Ti13Nb13Zr Alloy
PublicationThe development of composite oxide layers on the Ti13Nb13Zr alloy, their structure and properties have been demonstrated. Two subsequent methods were applied to prepare the composite layers. During the first stage gas oxidation produced a solid oxide layer, and subsequently oxide nanotubes were produced by using an electrochemical method. Scanning electron microscopy (SEM), chemical analysis, energy dispersive X-ray spectroscopy...
-
Report on investigation of turbine blade from main engine turbocharger 420.34 from M/V "Nordstraum"
PublicationWykonano badania pęknięcia na łopatce turbiny turbodoładowania silnika głównego. Ustalono, ze przyczyną pęknięcia była korozja międzykrystaliczna.
-
Requirements, modifications and methods of mechanical testing of bone cement – literature review
PublicationThe Aim of the paper is to show the basic requirements for the bone cement, its modifications in terms of physical, mechanical and biological properties and testing methods. This publication is intended to be a source of systematized basic knowledge regarding the modified bone cement.
-
REVERSE MODELLING OF MICROSEISMIC WAVES PROPAGATION FOR THE INTERPRETATION OF THE DATA FROM HYDRAULIC FRACTURING MONITORING IN POLAND
PublicationA hydraulic fracturing job was performed to stimulate gas flow from a horizontal wellbore located in Poland. The whole operation was overseen by means of microseismic monitoring. For this purpose, an array of 12000 geophones was deployed on ground in form of patches distributed unevenly in a region of 4km from the wellbore. The array was constantly recording seismic signals during whole fracturing processed. Such recorded signals...
-
Study of nanomechanical properties of (1-y)BST-yMgO thin films
PublicationIn the present study thin films of MgO – modified Ba0.6Sr0.4TiO3 (BST60/40) solid solution were prepared by the sol-gel-type chemical solution deposition method on stainless steel substrates. A multilayer spin-coating approach was utilized for the Ba0.6Sr0.4TiO3-MgO thin film deposition with subsequent thermal annealing at T=650-750C. Dried BST60/40-MgO gel powders were studied with thermogravimetric and differential thermal analysis...
-
Synthesis and structure of Bi 5 FeTi 3 O 15 ceramics
PublicationAim of the present research was to fabricate and study crystal structure and phase composition of Bi5FeTi3O15 (BTFO) ceramics exhibiting Aurivillius - type structure. By means of simultaneous thermal analysis and X-ray diffraction analysis the process of synthesis of BTFO ceramics has been studied. Mixed oxide method followed by pressureless sintering was used for ceramics preparation. Three endothermic thermal effects have been...
-
The Processing Procedure for the Interpretation of Microseismic Signal Acquired from a Surface Array During Hydraulic Fracturing in Pomerania Region in Poland
PublicationHydraulic fracturing is a procedure of injecting high pressure fluid into the wellbore in order to break shell rock and facilitate gas flow. It is a very costly procedure and, if not conducted properly, it may lead to environmental pollution. To avoid costs associated with pumping fluid outside the perspective (gas rich) zone and improve one’s knowledge about the reservoir rock, microseismic monitoring can be applied. The method...
-
Wykorzystanie tomografii komputerowej przy analizie jakości zacementowania - migracja gazu
PublicationArtykuł przedstawia opis zjawiska znanego w wiertnictwie otworowym jako migracja gazu. Opisano główne przyczyny powstawania tego negatywnego zjawiska polegającego na przepływie gazów a także płynów w zaczynie cementacyjnym lub kamieniu cementowym. Przygotowano próbki imitujące zacementowany odcinek rur okładzinowych. Skupiono się na wykorzystaniu tomografii komputerowej, oraz analizie zrekonstruowanego trójwymiarowego obrazu, w...
-
Wytwarzanie, budowa i właściwości warstw tlenkowych uzyskanych na stopach tytanu do zastosowań biomedycznych
PublicationPraca koncentruje się na zagadnieniach związanych z metodami modyfikacji warstwy wierzchniej stopów tytanu, z ukierunkowaniem na stop tytanu Ti13Nb13Zr, którego skład chemiczny stanowią pierwiastki obojętne dla organizmu żywego, a moduł Yong’a jest zbliżony do kości. Odpowiednia modyfikacja warstwy wierzchniej umożliwia przyspieszenie procesów łączenia żywej tkanki z wprowadzonym elementem i powoduje wydłużenie czasu użytkowania...
Year 2016
-
Analiza technologii lutowania próżniowego stali austenitycznej
PublicationCelem badań była ocena poprawności budowy złącza lutowanego próżniowo ze stali austenitycznej oraz analiza składu chemicznego charakterystycznych obszarów badanej próbki. Na podstawie badań wizualnych oraz metalograficznych na mikroskopie skaningowym (w tym analizy EDS) stwierdzono, że badane złącze charakteryzuje się prawidłową geometrią, jednak występują w nim liczne niezgodności (wydzielenia), co świadczy o nieprawidłowych parametrach...
-
Badanie wpływu zmian natężenia prądu na spawanie stopu aluminium
PublicationStop aluminium AW-7075 zyskuje coraz większą popularność w zastosowaniach komercyjnych ze względu na jego wyjątkowe właściwości fizyczne i mechaniczne: małą gęstość, wysoką wytrzymałość, udarność i plastyczność, bardzo dużą odporność na zmęczenie i zadowalającą na korozję, łatwą obrabialność i przetwarzalność. Ze względu na te właściwości, stop ten (AlZn5,5MgCu), zwany też FORTAL-em, używany jest dla części narażonych na wysokie...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublicationThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
Cavitation erosion resistance of thick CrC coating deposition by the Arc-PVD method
PublicationThe paper investigates the durability of chromium carbide (CrC) coatings, with thicknesses up to 20 μm, applied using the Arc-PVD technique, against cavitation erosion. The study employs the rotating disk testing method to evaluate the performance of these coatings. Findings indicate that the carbon content within the Cr-C coatings significantly influences their resistance to cavitation erosion, with variations ranging from 2 to...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Effect of Semiconductor Element Substitution on the Electric Properties of Barium Titanate Ceramics
PublicationThe investigated ceramics were prepared by a solid-state reaction from simple oxides and carbonates with the use of a mixed oxide method (MOM). The morphology of BaTi0.96Si0.04O3 (BTSi04) ceramics was characterised by means of a scanning electron microscopy (SEM). It was found that Si+4 ion substitution supported the grain growth process in BT-based ceramics. The EDS results confirmed the high purity and expected quantitative composition...
-
EFFECT OF SURFACE STATE AND STRESS ON AN OXIDATION OF THE ZIRCALOY-2 ALLOY
PublicationZr alloys are widely used as materials for nuclear fuel pellets in the nuclear industry. In the case of the LOCA or RIA happen, a temperature may locally reach high values. Even if the high temperature maintains shortly, the zirconium oxides may become permeable, absorb hydrogen appearing in cooling water from decomposition reaction and crack because of formation and brittle failure of hydrides. Such model cannot so far take into...
-
Ekspertyza dotycząca identyfikacji materiału uchwytów martwej kotwicy
PublicationWykonano badania identyfikacyjne materiału uchwytów kotwicy martwej