Wyszukiwarka
prof. dr hab. inż. Józef Tadeusz Haponiuk
Zatrudnienie
- Profesor w Katedra Technologii Polimerów
- 1974 - present Full Professor w Polymers Technology Department
Obszary badawcze
Publikacje
Filtry
wszystkich: 195
Katalog Publikacji
Rok 2018
-
Structure, Mechanical, Thermal and Fire Behavior Assessments of Environmentally Friendly Crude Glycerol-Based Rigid Polyisocyanurate Foams
PublikacjaIn this work, rigid polyisocyanurate foams were prepared at partial substitution (0–70 wt%) of commercially available petrochemical polyol, with previously synthesized biopolyol based on crude glycerol and castor oil. Influence of the biopolyol content on morphology, chemical structure, static and dynamic mechanical properties, thermal insulation properties, thermal stability and flammability was investigated. Incorporation of...
-
The Influence of Substitution of a Phosphorus-Containing Polyol with the Bio-polyol on the Properties of Bio-based PUR/PIR Foams
PublikacjaIn this work, effects of incorporating of a phosphorus-containing polyol into rigid polyurethane/polyisocyanurate foams’ formulations developed with use of two different bio-based polyols, derived from crude glycerol or liquefied cellulose were examined. The bio-polyol derived from crude glycerol was synthesized via two-step process from crude glycerol and castor oil, whereas the bio-polyol derived from liquefied cellulose was...
-
The study on application of biopolyols obtained by cellulose biomass liquefaction performed with crude glycerol for the synthesis of rigid polyurethane foams
PublikacjaIn this work rigid polyurethane foams (PUR) were obtained by replacement of 0–70 wt% of petrochemical polyol with bio-polyol obtained via cellulose liquefaction in presence of crude glycerol. The foams with different content of a bio-polyol were prepared by single step method for NCO/OH ratio equals 1.5. The prepared materials were analyzed in terms of their morphology, chemical structure, thermal stability and basic physical and...
-
Thermoplastic Elastomers Filled With GTR
PublikacjaIn recent years, searching for new and cost-effective methods of recycling waste tires has been a subject of research in many laboratories worldwide. This is due to regulations in the law and environmental factors, which have both stimulated industry to re-use high quality rubber found in ground tire rubber (GTR). One of the most promising solutions in this area seems to be thermoplastic elastomers (TPEs) filled with GTR, which...
-
Toughness augmentation by fibrillation and yielding in nanostructured blends with recycled polyurethane as a modifier
PublikacjaIn the present paper, we have carefully investigated the morphology and fracture mechanism of the recycled polyurethane (RPU) /epoxy blend system. The second phase (RPU) added to the epoxy resin has a positive effect on the overall mechanical properties. Interestingly, the recycled polymer has a remarkable effect on the fracture toughness of epoxy resin. The mechanism behind the fracture toughness improvement up on the addition...
-
Turmeric nanofiber-encapsulated natural product formulation act as a phytogenic feed additive—A study in broilers on growth performance, biochemical indices of blood, and E. coli in cecum
PublikacjaA phytogenic feed additive (PFA) formulation was prepared with bioactive molecules—curcuminoids, gingerol, and carvacrol by encapsulating in nanofiber isolated from turmeric spent (turmeric nanofiber, TNF). This formulation was completely characterized by scanning electron microscope, ultra performance liquid chromatography, and gas chromatography and evaluated for its efficacy. PFA-encapsulated TNF (PFA@TNF) considerably increased...
-
Two-step Conversion of Crude Glycerol Generated by Biodiesel Production into Biopolyols: Synthesis, Structural and Physical Chemical Characterization
PublikacjaIn this work biopolyols were synthesized via two-step process from crude glycerol and castor oil. For better evaluation of analyzed process, the impact of its time and temperature on the structure and properties of biopolyols was determined. Obtained results fully justified conducting of synthesis in two steps. Prepared materials were characterized by hydroxyl value and water content comparable to polyols industrially applied in...
-
Use of Ginger Nanofibers for the Preparation of Cellulose Nanocomposites and Their Antimicrobial Activities
PublikacjaHere, we report, for the first time, the isolation of ginger nanofibers (GNF) from ginger rhizomes spent by acid hydrolysis and followed by high-pressure homogenization. Scanning electron microscopy was utilized to identify the surface morphology of the GNF and the widths ranged between 130 to 200 nm. Structural analysis of GNF was identified by Fourier transform infrared spectroscopy, Differential scanning calorimetry, and X-ray...
-
Use of Ginger Nanofibers for the Preparation of Cellulose Nanocomposites and Their Antimicrobial Activities
Publikacja
Rok 2017
-
CROSSLINKING OF EPOXY-OLIGOESTERIC MIXTURES IN THE PRESENCE OF DIOXYDIPHENYLPROPANE DIGLYCIDYL ETHER MODIFIED WITH ADIPIC ACID
Publikacja -
In-Situ Processing of Biocomposites via Reactive Extrusion
PublikacjaLaw regulations, economic and environmental factors are the main causes for the rapidly growing interests in biocomposites’ research, conducted currently in a number of academic and industrial scientific centers. However, weak polymer matrix/filler interactions, common in biocomposites, result in unsatisfactory mechanical properties, which limit their practical applications. From many attempts performed to solve this problem, in-situ...
-
Liquefaction of macroalgae Enteromorpha biomass for the preparation of biopolyols by using crude glycerol
PublikacjaThis article describes the liquefaction process of macroalgae Enteromorpha with the use of crude glycerol as a solvent and a reagent, aimed at obtaining of new bio-polyols, which are characterized with respect to their chemical structure, physical and thermal properties. Six different biopolyols were prepared. In order to optimize the liquefaction of algal biomass for the best bio-polyol properties, two catalysts (sulfuric or orthophosphoric...
-
Performance properties of rigid polyurethane-polyisocyanurate/brewers’ spent grain foamed composites as function of isocyanate index
PublikacjaIn the presented work, rigid polyurethane-polyisocyanurate (PUR-PIR) foams filled with brewers’ spent grain (BSG) were prepared. The influence of the isocyanate index (II) on its performance was investigated. Foams obtained with higher isocyanate index required a higher amount of hydrofluorocarbon physical blowing agent to provide the same apparent density of material. An increase of isocyanate index resulted in a slight decrease...
-
Preparation, characterization and anti-colitis activity of curcumin-asafoetida complex encapsulated in turmeric nanofiber
PublikacjaUlcerative colitis (UC) is a main form of inflammatory bowel disease (IBD). Asafoetida (ASF) and turmeric have traditionally been used for the treatment of various inflammatory diseases, including UC, because ASF is rich in sulfur compounds and turmeric contains curcumin (CUR). Turmeric nanofiber (TNF), the modified cell wall component of turmeric is considered to play important role in the human diet, health and can be used as...
-
PU Polymers, Their Composites, and Nanocomposites: State of the Art and New Challenges
PublikacjaThe chapter is a review of the polyurethane(PU)-based composites and nanocomposites. The chapter details different components in the manufacturing of PU polymers, composites, and nanocomposites. The different types of glycols, isocyanates, and catalysts that are used for the synthesis of different polyurethanes are discussed. The applications and specialties of polyurethane composites and nanocomposites are also elaborated on.
-
Renewable Resources for Polyurethanes and Polyurethane Composites: A Review
PublikacjaEach year, more than two million tons of polyurethane is produced in the EU by reacting isocyanates with polyols made from fossil fuel. In addition, there are appreciable quantities of petroleum based functional additives applied in the industry nowadays for both polyols and polyurethane materials. It is therefore of key importance to develop sustainable economically viable polyols with enhanced functionalities, and thereby reducing...
-
Termooksydacyjna i fotooksydacyjna degradacja pianek poliuretanowych
PublikacjaPrzeprowadzono ocenę efektywności działania wybranych środków przeciwstarzeniowych w sztywnych piankach poliuretanowych, otrzymywanych na drodze syntezy jednoetapowej. Ocenę tę oparto na pomia-rach zmian barwy oraz wytrzymałości mechanicznej zsyntezowanych materiałów. Na podstawie analizy uzyskanych wyników stwierdzono, iż dodatek 3% mieszaniny I rzędowego antyutleniacza fenolowego oraz benzotriazolowego absorbera UV znacząco zmniejsza...
-
The influence of crude glycerol and castor oil-based polyol on the structure and performance of rigid polyurethane-polyisocyanurate foams
PublikacjaIn this work, biopolyol obtained from two types of industrial crops’ processing products: crude glycerol and castor oil was used for preparation or rigid polyurethane-polyisocyanurate foams. Bio-based polyol was obtained via crude glycerol polymerization and further condensation of resulting polyglycerol with castor oil. Rigid polyurethane-polyisocyanurate foams were prepared at partial substitution (0–70 wt.%) of petrochemical...
-
Toward Polyethylene–Polyester Block and Graft Copolymers with Tunable Polarity
PublikacjaThe synthesis and characterization of polyethylene–polyester block and graft copolymers and their potential as compatibilizers in polyethylene-based polymer blends are being described. The various routes to functionalized polyethylenes and the corresponding block/graft copolymers have been compared and evaluated for their scalability to industrial scale production. Hydroxyl chain-end and randomly OH-functionalized HDPE as well...
Rok 2016
-
A recent developments in polyurethane foams containing a low-cost and pro-ecological modifiers
PublikacjaDiversity of the polyurethane (PU) foams applications cause that investigation of the relationships between their structure and properties is currently very popular topic among the many research institutions and companies. At the turn of the last years many scientific papers about PU foams and their composites were published. The one of the main research trends in this field is related to the reduction of production costs of...
-
Assessment of microstructure, physical and thermal properties of bitumen modified with LDPE/GTR/elastomer ternary blends
PublikacjaLDPE/GTR/elastomer ternary blends with variable LDPE/GTR ratio and constant elastomer content were prepared via melt-compounding. Obtained LDPE/GTR/elastomer blends were applied as thermoplastic modifiers into bitumen. Microstructure, physical and thermal properties of the modified bitumen were determined. It was observed that chemical composition of LDPE/GTR/elastomer blends has significant influence on their density and rheological...
-
Badania próbek płyt podeszwowych dostarczonych przez Zamawiającego
PublikacjaPrzedmiotem umowy jest przeprowadzenie badań mających na celu określenie czy dostarczone przez Zamawiającego próbki płyt podeszwowych zostały wykonane z tworzywa termoplastycznego.
-
Biopolyols obtained via crude glycerol-based liquefaction of cellulose: their structural, rheological and thermal characterization
PublikacjaIn this work lignocellulose biomass liquefaction was used to produce biopolyols suitable for the manufacturing of rigid polyurethane foams. In order to better evaluate the mechanism of the process, pure cellulose was applied as a raw material. The effect of time and temperature on the effectiveness of liquefaction and the parameters of resulting biopolyols were characterized. The prepared materials were analyzed in terms of their...
-
Interfacial adhesion evaluation in (low-density polyethylene)/elastomer blends
PublikacjaLow-density polyethylene (LDPE) with different elastomers at a ratio of 50/50 wt% blends was prepared by using a co-rotating twin-screw extruder. Three kinds of elastomers were used: ground tire rubber (GTR), partially crosslinked butyl rubber (KalarVR ), and styrenebutadiene- rubber block copolymer (SBS; KratonVR ). For better characterization of interaction between polyethylene and elastomer, influence of the type of elastomer on...
-
Microwave Assisted Liquefaction with Crude Glycerol as a Potential Method of Brewer’s Spent Grain Utilization
Publikacja -
Microwave assisted liquefaction with crude glycerol as a potential method of brewer's spent grain utylization
PublikacjaBrewer's spent grain was applied as a low-cost industrial type of lignocellulose biomass in a liquefaction and solvent: biomass ratio on the efficiency of the process, chemical structure and basic properties of obtained prepared polyols and soil residues shed light on the biomass degradation mechanism through application of microwaves and further reaction of degradation products with solvent particles.
-
Potential applications of crude glycerol in polymer technology–Current state and perspectives
PublikacjaThe increasing use of bio-based fuels and fuel additives, among them biodiesel, causes significant surplus of crude glycerol on the market which creates new challenges in terms of its sustainable utilization. A lot of ways for the incorporation of this by-product into different branches of industry requires purification by expensive and complicated processes. Therefore, researchers are seeking for applications of untreated crude...
-
Preface
Publikacja -
RECENT DEVELOPMENTS IN POLYURETHANE FOAMS CONTAINING LOW-COST AND PRO-ECOLOGICAL MODIFIERS
Publikacja -
Recycled Polyethylene terephthalate (PET) as Construction Material in Civil Engineering: A Review
PublikacjaIn general, the quantity of plastics of all types consumed annually all over the world has been growing in a phenomenal way. The manufacturing processes, service industries and municipal solid wastes (MSW) generate numerous waste plastic materials. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. It is believed that the management of solid...
-
Styrene-Butadiene Rubber/Modified Ground Tire Rubber Blends Co-Vulcanization: Effect of Accelerator Type
PublikacjaGround tire rubber was thermo-mechanically modified with using a co-rotating twin screw extruder. Modification of GTR was conducted in autothermal conditions. Styrene-butadiene rubber and modified ground tire rubber blends were prepared via two-roll milling. Obtained compounds were cured with conventional system (sulfur/vulcanization accelerator ratio was 2:1). During this research three commonly vulcanization accelerators (MBT,...
-
Thermomechanical reclaiming of ground tire rubber via extrusion at low temperature: Efficiency and limits
Publikacja -
Thermo-mechanical reclaiming of ground tire rubber via extrusion at low temperature: Efficiency and limits
PublikacjaThermomechanical reclaiming of ground tire rubber (GTR) was performed at different temperatures (60, 120, and 180°C) using a co-rotating twin-screw extruder. Obtained samples were used in styrene-butadiene rubber (SBR) blends. As reference samples, SBR compounds containing untreated GTR were used. Curing characteristics, static and dynamic mechanical properties, and morphology of the obtained blends were determined. The results...
Rok 2015
-
Chromatografia gazowa jako skuteczne narzędzie kontroli procesu wytłaczania
PublikacjaPraca stanowi literaturowy przegląd możliwości wykorzystania chromatografii gazowej (GC) jako narzędzia kontroli procesu wytłaczania materiałów polimerowych. Przedstawiono charakterystykę techniki GC oraz możliwości, jakie niesie ze sobą kontrola fazy gazowej uwalnianej podczas przetwórstwa materiałów polimerowych. Na podstawie dotychczas opublikowanych prac badawczych omówiono techniki i metody wykorzystywane do izolacji lotnych...
-
Curing characteristics, mechanical and thermal properties of reclaimed ground tire rubber cured with various vulcanizing systems
PublikacjaGround tire rubber was thermo-mechanical reclaimed at 120 °C using a co-rotating twin screw extruder. The effect of vulcanizing system type on curing characteristics, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and thermal properties of reclaimed ground tire rubber was investigated. Reclaimed rubber was cured using different types of vulcanization...
-
Ekspertyza uzupełniająca opinię biegłego sądowego dotyczącą powodu występowania wycieku uszczelniacza butylowego do wnętrza pakietu okiennego
PublikacjaW niniejszym dokumencie ekspertyzę uzupełniającą opinię biegłego sądowego dotyczącą powodu występowania wycieku uszczelniacza butylowego do wnętrza pakietu okiennego. Wyniki przeprowadzonych badań wskazują, iż Silikon o nazwie handlowej “Bosman” dostarczony od strony pozwanej nie jest identyczny pod względem chemicznym niż ten stosowany przez powoda. Silikon stosowany przez powoda rozmiękcza uszczelniacz butylowy stosowany w...
-
Investigation of volatile low molecular weight compounds formed during continuous reclaiming of ground tire rubber
PublikacjaGround tire rubber was thermo-mechanically reclaimed at different temperature conditions (80, 120, 160 °C) using a co-rotating twin screw extruder. The progress of ground tire rubber reclaiming was evaluated with specific mechanical energy, sol fraction and thermogravimetric analysis. Volatile organic compounds (VOCs) including volatile sulfur compounds (VCSs) released from ground tire rubber and ground tire rubber after reclaiming...
-
Kontrola jakości materiałów polimerowych wytwarzanych metodą wytłaczania: stan obecny i perspektywy rozwoju
PublikacjaNiniejsza praca stanowi przegląd literaturowy metod kontroli jakości materiałów polimerowych wytwarzanych metodą wytłaczania. Scharakteryzowano możliwości kontroli efektywności procesu wytłaczania działających w układach "on-line" oraz "in-line", które polegają na przeprowadzeniu pomiarów w czasie trwania procesu. Opisano potencjał aplikacyjny technik spektroskopowych (IR, UV-VIS), pomiarów właściwości reologicznych, analizy morfologii...
Rok 2014
-
Characterization and properties of LDPE/(ground tire rubber)/crosslinked butyl rubber blends
Publikacja -
Characterization and properties of LDPE/(ground tire rubber)/crosslinked butyl rubber blends
PublikacjaIn recent years, interest in used rubber recycling, mainly focusing on the utilization of end-of-life tires, has heightened. This interest, is owing to the activities related to environmental protection and economic factors, which both stimulate companies to reuse the high-quality rubber present in ground rubber scrap. In this study, the application of crosslinked butyl rubber in thermoplastic compositions of low-density polyethylene...
-
Compatibilization of polymeric composition filled with ground tire rubber – short review
PublikacjaWaste rubber is recognized as valuable materials resource and searching for new recycling methods is the main activity of many research institutions and companies. At the turn of the last years only few scientific papers about foamed polymer compositions filled with ground tire rubber were published. In paper review about progress in compatibilization and foaming of polymeric compositions filled with ground tire rubber.
-
Cross-linking of epoxy-oligomeric mixtures in the presence of modified phenol-formaldehyde resins
PublikacjaCross-linking of epoxy oligomeric mixtures consisting of industrial epoxy resin ED-20, oligoetheracrylate TGM-3, peroxide derivative of epoxy resin ED-24 and phenol-formaldehyde oligomer with unsaturated methacrylate fragments or peroxide groups was studied in the presence of polyethylenepolyamine at room temperature and heated to 383, 403 or 423 K for 15, 30, 45, 60 and 75 minute. The influence of mixture composition, temperature...
-
Curing characteristics, mechanical properties and morphology of butyl rubber filled with ground tire rubber (GTR)
PublikacjaThe results on testing application of ground tire rubber (GTR), as potential filler for butyl rubber, are pre- sented. The GTR content variation, within the range of 10–90 phr, was studied with respect to the vulcanization process, static mechanical properties (tensile strength, elongation-at-break, hardness and resilience), dynamic mechanical properties and the morphology of the obtained vulcanizates. Butyl rubber was characterized...
-
Ekspertyza w celu ustalenia utraty właściwości powłoki epoksydowej zastosowanej na konstrukcji stalowej - Raport z badań zleconych - Numer umowy: 031008
Publikacja.
-
Reclaiming ground tire rubber at low temperatures: benefits and limitations
PublikacjaLower extrusion temperatures during rubber reclamation lead to a reduction in toxic degradation products and improve the mechanical properties of vulcanizates, at the expense of reduced processability.
-
Rigid polyurethane foams from a polyglycerol-based polyol
PublikacjaRigid polyurethane foams (rPUs) were synthesized by replacing 35 and 70 wt.% of petrochemical polyol with polyglycerol. Two types of polyglycerol with different molecular weights and hydroxyl numbers were used to obtain new ‘‘green’’ polyurethane–polyglycerol foams. The foams were prepared by a single step method for the ratio of NCO/OH groups equal to 2. rPUs synthesized with polyglycerol showed regular cellular structure, with...
-
The influence of screw configuration and screw speed of co-rotating twin screw extruder on the properties of products obtained by thermomechanical reclaiming of ground tire rubber
PublikacjaThe results of our investigations on the process of continuous thermomechanical reclaiming of ground tire rubber (GTR) carried out using a twin screw extruder are presented.We used a co-rotating twin screw extruder with a special configuration of plasticizing unit, enabling generation of considerable shear forces. The influence of screw configuration and screw speed on breaking of chemical crosslink bonds contained in ground tire...
-
Wpływ kolejności dozowania surowców oraz sił ścinających na właściwości mieszanin polietylen dużej gęstości/miał gumowy, wytwarzanych przy użyciu współbieżnej wytłaczarki dwuślimakowej
PublikacjaKompozycje termoplastyczne polietylenu dużej gęstości (PE-HD) z udziałem 50 % mas. miału gumowego (GTR), wytwarzano przy użyciu współbieżnej wytłaczarki dwuślimakowej. Scharakteryzowano wpływ kolejności dozowania surowców oraz sił ścinających generowanych podczas intensywnego mieszania na parametry pracy wytłaczarki, wartości masowego wskaźnika szybkości płynięcia, statyczne właściwości mechaniczne (wytrzymałość na rozciąganie,...
-
Wykonanie badań składu próbek mieszanki gumowej, z której wykonane są urządzenia odbojowe zainstalowane na nabrzeżach Portu Gdańskiego
PublikacjaScharakteryzowano właściwości fizyczne, termiczne oraz strukturę chemiczną próbek wulkanizatów gumowych pobranych z odbojnic odbojowe zainstalowanych na nabrzeżach Portu Gdańskiego.
-
Wykonanie ekspertyzy dotyczącej określenia właściwości kleju ULTRABOND ECO VS90
PublikacjaScharakteryzowano właściwości mechaniczne połączeń klejonych, oraz reologię i skład chemiczny próbek klejów dostarczonych przez Zleceniodawcę.
wyświetlono 6579 razy