Publikacje
Filtry
wszystkich: 197
Katalog Publikacji
Rok 2016
-
Heat capacities and thermodynamic properties of antimony substituted lanthanum orthoniobates
PublikacjaThe results of heat capacity measurements for the lanthanum orthoniobate substituted with 10, 20 and 30 mol% of antimony (LaNb0.9Sb0.1O4, LaNb0.8Sb0.2O4 and LaNb0.7Sb0.3O4) are presented and discussed. Temperature dependence of low temperature heat capacity was analyzed within the Debye and Einstein models. The Debye temperature decreased, whereas the Einstein temperature increased with antimony content. The decrease of the Debye...
-
Influence of Sb-substitution on ionic transport in lanthanum orthoniobates
PublikacjaThe results of ionic transport measurements for the lanthanum orthoniobate substituted with 10 and 30 mol% of antimony (LaNb0.9Sb0.1O4 and LaNb0.7Sb0.3O4) are presented and discussed. The influence of calcium co-doping on these properties has also been analysed. It has been shown that for the investigated material protonic conductivity predominates at temperatures up to 800 °C in oxidizing atmospheres under wet conditions. The...
-
Nanoporous TiO2 electrode grown by laser ablation of titanium in air at atmospheric pressure and room temperature
PublikacjaRecently, fabrication of the nanoporous TiO2 photoelectrode on metal foils by means of sputtering of the Ti film on preheatedmetal substrate followed by the TiO2 deposition (doctor blade technique) and sintering represents the frequently applied technique. This is despite the relatively complicated procedure and number of parameters to be controlled in order to fabricate films of required properties. In this work an approach is...
-
Photocatalytic activity of nitrogen doped TiO2 nanotubes prepared by anodic oxidation: The effect of applied voltage, anodization time and amount of nitrogen dopant
PublikacjaNitrogen doped TiO2 nanotube arrays were prepared by anodizing Ti foils in an organic electrolyte containing specified amounts of urea as nitrogen precursor. The photocatalytic activity of the samples was evaluated by analyzing the degradation kinetics of phenol in water. The influence of tubes’ length, tubes’ surface morphology and amount of nitrogen in the TiO2 lattice on hydroxyl radical formation efficiency, photocatalytic...
Rok 2015
-
Characterization of magnesium doped lanthanum orthoniobate synthesized by molten salt route
PublikacjaMolten salt synthesis method has been used to prepare the single phase magnesium doped lanthanum orthoniobate. The phase composition has been checked by X-ray diffraction method and the microstructure studies have been performed by scanning electron microscopy. The high temperature properties of the material have been investigated by thermogravimetry and electrochemical impedance spectroscopy. A dependence between sample total...
-
Electrical conductivity and relaxation processes in V2O5 nanorods prepared by sol–gel method
PublikacjaProperties of high purity V2O5 nanorods prepared by a sol – gel method are presented. The studied materials were characterized by: X-ray diffractometry (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The electrical impedance was measured as a function of temperature and frequency. The obtained results show that the electrical conductivity increases with increasing temperature. The d.c. conductivity...
-
Electronic and ionic relaxations in strontium-borate glass and glass-ceramics containing bismuth and vanadium oxides
PublikacjaThe topography, microstructure and electrical properties of strontium-borate glass and SBO glass containing bismuth and vanadium oxides, were studied. The structure was measured using X-ray diffraction (XRD), Energy Dispersive X-ray Spectrometer (EDS) and Scanning electron microscope (SEM) methods. The A.C. complex conductivity was investigated as a function of temperature and frequency. The influence of the quantity of bismuth...
-
Formation of Highly Conductive Boron-Doped Diamond on TiO2 Nanotubes Composite for Supercapacitor or Energy Storage Devices
PublikacjaIn the present paper, we report the phenomena of the formation of the novel composite nanostructures based on TiO2 nanotubes (NTs) over-grown by thin boron-doped diamond (BDD) film produced in Microwave Plasma Enhanced Chemical Vapor Deposition (PE MWCVD). The TiO2 nanotube array overgrown by boron-doped diamond immersed in 0.1 M NaNO3 can deliver high specific capacitance of 7.46 mF cm−2. The composite electrodes were characterized...
-
Influence of Antimony Substitution on Spontaneous Strain and Thermodynamic Stability of Lanthanum Orthoniobate
PublikacjaThe analysis of the antimony substitution influence on temperature dependence of unit cell distortion has been done. The values of spontaneous strain and Landau order parameter for three different antimony contents varied had been calculated. The phase transition occurring for antimony substituted lanthanum orthoniobate was found to be second order. The high temperature solution calorimetry method has been used to investigate...
-
Investigation of catalytic layers on anode for solid oxide fuel cells operating with synthetic biogas
PublikacjaIn this paper solid oxide fuel cells operating with dry synthetic biogas have been examined. In order to increase their stability the layers of CuO-CeO2, Cu1.3Mn1.7O4 and Y0.08Sr0.92Ti0.8Fe0.2O3 -δ have been deposited on the Ni-YSZ anode site. These layers should catalyze the internal biogas reforming and prevent the carbon deposition on the anode site. It has been found that CuO-CeO2 and Cu1.3Mn1.7O4 catalysts led to an increase...
-
Investigation of thin perovskite layers between cathode and doped ceria used as buffer layer in solid oxide fuel cells
PublikacjaIn this paper, thin perovskite layers between cathode material of solid oxide fuel cells and gadolinia-doped ceria buffer layer are investigated. Thin layers made of LaNi0.6Fe0.4O3-δ (LNF), La0.6Sr0.4Co0.2Fe0.8O3-δ (LSCF), or SrTi0.65Fe0.35O3-δ (STF) were symmetrically deposited by spin coating method from metallo-organic polymer precursors on a Ce0.8Gd0.2O2-δ (CGO) substrate. Porous and about 40-μm-thick LNF cathodes were deposited...
-
Nonlinear and linear impedance of bismuth vanadate ceramics and its relation to structural properties
PublikacjaThe nonlinear and linear electrical properties, topography, and microstructure of bismuth-vanadate ceramics, were studied. The structurewas observed with the use of X-ray diffraction (XRD), scanning electronmicroscopy (SEM), atomic force microscopy (AFM) and confocal microscopy methods. The obtained results showed that ceramic is porous. Two phase transitionswere determinedwith the use of DSC measurements. The linear and nonlinear ac...
-
Pressure effects on the superconductivity of the HfPd2Al Heusler compound: Experimental and theoretical study
PublikacjaPolycrystalline HfPd2Al has been synthesized using the arc-melting method and studied under ambient-pressure conditions by x-ray diffraction from room temperature up to 450 °C. High-pressure x-ray diffraction up to 23 GPa was also performed using Diacell-type membrane diamond anvil cells. The estimated linear thermal expansion coefficient was found to be α=1.40(3)×10−5K−1, and the bulk modulus derived from the fit to the third-order...
-
Proton Conducting Ceramic Powder Synthesis by a Low Temperature Method
PublikacjaMolten salt synthesis (MSS) is a simple method for the preparation of ceramic powders with specific morphology. The main role of the molten salts is to increase the reaction rate and lower the reaction temperature. It occurs because of much higher mobility of reactants in the liquid medium than in the solid state. In this work the molten salt synthesis was applied to produce ceramic powders of La0995Ca0005NbO4 and BaCe09−xZrxY01O3....
-
Tin oxide nanoparticles from laser ablation encapsulated in a carbonaceous matrix – a negative electrode in lithium-ion battery applications
PublikacjaThis report concerns carbonaceous electrodes doped with tin(II) oxide nanoparticles. Tin nanoparticles are obtained by pulsed laser ablation in water. Crystalline nanoparticles have been encapsulated in a carbonaceous matrix formed after pyrolysis of a mixture consisting of tin/tin(IV) oxide nanoparticles and gelatine. The obtained material is characterized by means of X-ray diffraction, selected area diffraction, scanning electron...
-
Visible light activity of rare earth metal doped (Er3+, Yb3+ or Er3+/Yb3+) titania photocatalysts
PublikacjaA series of Er3+-TiO2, Yb3+-TiO2 and Er3+/Yb3+-TiO2 photocatalysts were obtained via sol-gel method, using rare earth metal (RE) precursor ranging from 0.25 to 10 mol%. The experiments demonstrated that phenol in aqueous solutions was successfully degraded under visible light (> 450 nm) using RE3+-TiO2. The as-prepared samples were characterized by X-ray diffraction (XRD), X-ray photoelectron emission spectroscopy (XPS), UV-Vis...
Rok 2014
-
Cadmium complex possessing simultaneously silanethiolato- and dithiocarbamato-ligands. A novel single-source precursor of cadmium sulfide
PublikacjaThermal decomposition of suitable coordination compounds may be used as efficient route for fabrication of semiconducting layers. A new potential CdS precursor—a cadmium complex with all-sulfur Cd-coordination sphere [Cd{l-SSi(OBut)3}(S2CNC4H8)]2 (1) —has been prepared and its properties are investigated. The complex was obtained in the reaction between dimeric bis(tri-tert-butoxysilanethiolato) cadmium(II) [Cd{SSi(OBut)3}2]2 and...
-
Correlation between structural and electrical properties in highly porous (Y,Sr)(Ti,Nb)O3-delta SOFC anodes
PublikacjaIn order to find a relationship between structural and electrical properties, niobium and yttrium doped SrTiO3 ceramics were prepared via solid-state reaction. The samples were sintered in hydrogen and air conditions. The samples were also fabricated with a pore-former to obtain highly porous specimens. The electrical properties of Nb-doped SrTiO3 samples and yttrium and niobium co-doped SrTiO3 were compared. The comparable electrical...
-
Effect of isovalent substitution on microstructure and phase transition of LaNb1−xMxO4 (M=Sb, V or Ta; x=0.05–0.3)
PublikacjaLaNb1−xMxO4 oxides with pentavalent elements of different ionic sizes (M=Sb, Ta and V, x=0.05–0.3) were synthesized by the solid state reaction method. Special interest was devoted to the antimony substituted lanthanum niobate which is a new material in this group. Rietveld analysis of the X-ray diffraction patterns was used to determine the influence of the material composition on unit cell parameters. On the basis of dilatometric...
-
Electrical properties and structure of lead-borate glass containing iron ions.
PublikacjaThe ac and dc conductivity in iron–lead-borate glass samples was investigated in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by the means of atomic force microscopy (AFM) and the crystalline phases (if present) were identified by the means of X-ray diffractometry. Two types of ac electrical behaviour were observed. The first group of glass samples which...
-
Electronic conductivity in the SiO2-PbO-Fe2O3 glass containing magnetic nanostructures
PublikacjaThe linear impedance spectra of iron–silicate–lead glass samples were measured in the frequency range from 1 MHz to 1 MHz and in the temperature range from 153 K to 423 K. The structure was investigated by means of XRD and atomic force microscopy. Local electrical and magnetic properties of the samples were tested with the aid of electrostatic force microscopy (EFM) and magnetic force microscopy (MFM). The obtained results show...
-
Impedance Studies of Phosphate-iron Glasses Containing Niobium and Titanium
PublikacjaThe ac and dc conductivity in phosphate-iron-niobate glasses with addition of titanium oxide was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and confocal microscopy methods. The obtained results show that all samples are amorphous but they...
-
Interaction of SrTi0.65Fe0.35O3-δ with LaNi0.6Fe0.4O3-δ, La0.6Sr0.4Co0.2Fe0.8O3-δ and Ce0.8Gd0.2O2-δ
PublikacjaIron doped strontium titanates SrTi1-xFexO3-δ are perovskites of versatile properties. They can be used in solid oxide fuel cells or high temperature oxygen sensors. Their reactivity with electrolyte materials, cathode buffer layer materials, other cathode materials or current collector layers has not been fully tested. In this study we use X-ray diffraction to check SrTi0.65Fe0.35O3-δ compatibility with Ce0.8Gd0.2O2-δ (used as...
-
Lanthanide co-doped TiO2: the effect of metal type and amount on surface properties and photocatalytic activity
PublikacjaPreparation of new rare earth metal-containing TiO2 nanocomposites (Nd3+/Er3+, Nd3+/Eu3+, Eu3+/Ho3+-TiO2) using sol–gel route and their photoactivity under visible and ultraviolet light is reported. The obtained photocatalysts were subsequently characterized by Brunauer–Emmett–Teller (BET) method, UV–Vis diffuse-reflectance spectroscopy (DRS), luminescence spectroscopy, X-ray photoelectron spectroscopy (XPS) and X-ray powder diffraction...
-
Microstructure and Dielectric Properties of Barium-vanadate Glasses
PublikacjaThe ac and dc conductivity in barium-vanadate glasses was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods. The XRD results show that all samples are amorphous but microscopy investigation reveals that glasses with greater amount of V2O5...
-
Nanostructure and dielectric behavior of vanadate glasses containing BaTiO3
PublikacjaThe ac and dc electrical conductivity of barium titanate doped bismuth-vanadate as-quenched and heat-treated materials was measured in the frequency range from 1 mHz to 1 MHz and in the temperature range from 153 K to 423 K with the impedance spectroscopy method. The microstructure was investigated by means of XRD, scanning electron microscopy (SEM), atomic force microscopy (AFM) and confocal microscopy. The obtained results showed...
-
Ordered TiO2 nanotubes: the effect of preparation parameters on the photocatalytic activity in air purification process
PublikacjaVertically ordered TiO2 nanotube arrays were synthesized by anodic oxidation of titanium foil in glycerol, ethylene glycol and water-based electrolytes. The effect of electrolyte composition, anodization voltage, ultrasonic treatment and calcination time on the morphology of the resulting thin films, as well as on their photocatalytic activity in toluene removal, used as a model volatile organic compound, was investigated. Toluene,...
-
Phase Separation and Electrical Properties of Manganese Borosilicate Glasses
PublikacjaThe structure and electrical properties of manganese borosilicate glasses of a composition of xMnO-(0.8-x)SiO2-(0.2)B2O3 (x=0.4, 0.5 and 0.6 in mol) were investigated by impedance spectroscopy, SEM, XRD and confocal microscopy methods. The influence of composition on the glass structure and electrical properties was discussed. A separation of two amorphous phases was observed and it was concluded that one phase is SiO2-rich and...
-
Synthesis and Testing of BCZY/LNZ Mixed Proton–electron Conducting Composites for Fuel Cell Applications
PublikacjaA composite of BaCe0.6Zr0.2Y0.2O3–δ and Li2O:NiO:ZnO was investigated for fuel cell applications. The composite was successfully synthesized and its phase stability was confirmed at temperatures up to 900 °C. The influence of sintering and pressing aids on density was also investigated. Electrical properties were measured. DC electrical conductivity was about 8•10-4 S/m at 845 K. Open circuit voltage measurements in wet hydrogen...
-
The properties of reduced Bi-Ge-O glasses for thermoelectric devices
PublikacjaThe bismuth-germanate glasses have been investigated to examine their applicability for thermoelectric devices. In order to increase their electrical conductivity, the 25Bi2O3–75GeO2 glass samples have been reduced at 340-380°C for 10 hours in hydrogen. It has been shown that such heat treatment in H2 leads to the reduction of metal ions Bi3+ and Ge4+ into neutral atoms and the formation of metal grains both in an amorphous glass...
-
The properties of reduced Ge-Sb-O glasses for thermoelectric devices
PublikacjaThe structural and electrical properties of germanium-antimonate glasses after heat treatment in hydrogen have been determined. In the case of 50GeO2-50Sb2O3 glass reduced at 340°C even for less than 1 hour a continuous layer of antimony granules is formed and its electrical properties determine the surface conductivity of the reduced sample. The bulk electrical conductivity at 100°C of this sample was determined as 1000 Scm-1...
Rok 2013
-
Application of wet powder spraying for anode supported solid oxide fuel cell with a perowskite SrTi0.98Nb0.02O3-d anode
PublikacjaAnode-supported solid oxide fuel cell with SrTi0.98Nb0.02O3–d anode, yttria-stabilized zirconia electrolyte and La(Ni0.6Fe0.4) O3d cathode has been successfully fabricated and evaluated. Process of anode support fabrication has been presented. Wet powder spraying and high temperature sintering method have been studied and applied to deposit the thin electrolyte layer.In order to improve catalytic properties of the anode, it has...
-
Auksetyczne pianki poliuretanowe
PublikacjaPrzedmiotem badań były auksetyczne pianki poliuretanowe wytworzone metodą trójosiowej termo-kompresji z konwencjonalnych elastycznych pianek poliuretanowych. Materiały auksetyczne charak-teryzują się ujemnym współczynnikiem Poissona i dzięki swojej strukturze komórkowej charakteryzują się unikalnymi właściwościami fizyko-mechanicznymi. Zbadano wpływ trójosiowej termokompresji na zmianę właściwości mechanicznych oraz struktury otrzymanej...
-
Characterization of CaTi0.9Fe0.1O3/La0.98Mg0.02NbO4 composite
PublikacjaA composite of CaTi0.9Fe0.1O3 and electrolyte material, i.e. magnesium doped La0.98Mg0.02NbO4 was prepared and studied. The phase content and the sample microstructure was examined by an X-ray diffraction method and scanning electron microscopy. EDS measurements were done both for composite samples and the diffusion couple. The electrical properties were studied by four terminal DC method. The Ahigh-temperature interaction between...
-
EFFECTS OF DOPING ON STRUCTURE AND PHASE TRANSITION OF HIGH TEMPERATURE PROTON CONDUCTOR LaNb1-xMxO4-σ (M=As, Sb, V, Ta AND X=0,05 TO 0,3)
PublikacjaIn this work synthesis of lanthanum orthoniobate has been done. Doping by arsenic, antimony, vanadium or tantalum in 5% to 30% have been introduced. The relationship between doping type and percentage and structural properties of the material have been investigated.
-
Interactions between components of SrTi0.98 Nb0.02O3-δ-YSZ and SrTi0.98 Nb0.02O3-δ -CeO2 composites
PublikacjaComposites consisting of SrTiO3-based perovskite and either yttria-stabilized zirconia or ceria were investigated. The mechanical compatibility and possible inter-diffusion between phases were characterized by scanning electron microscopy, X-ray diffraction, and energy-dispersive X-ray spectroscopy. A gradual disappearance of Ce-containing phases with an increase in the temperature of reduction in hydrogen was noticed. Moreover,...
-
Investigation methods of ionic conductivity measurements in polycrystalline MIEC (mixed ionic-electronic conductor) based on perovskite ceramics
PublikacjaPaper about the measurements of ionic conductivity in LSM and strontium titanate ceramics.
-
Investigation of functional layers of solid oxide fuel cell anodes for synthetic biogas reforming
PublikacjaSolid oxide fuel cells (SOFCs) are one of the most promising energy conversion devices due to their high efficiency, low pollution and fuel flexibility. Unfortunately, when hydrocarbons are used as a fuel, for example in the form of a biogas, solid carbon can deposit on the anode surface. This process leads to the degradation of the fuel cell performance. A possible solution to this problem is to apply an additional catalytic material,...
-
Investigation of sensing mechanism of Nasicon electrocatalytic sensors in nitrogen dioxide and ammonia
PublikacjaIn this paper a sensing mechanism of Nasicon electrocatalytic sensor in nitrogen dioxide and ammonia is investigated. Both gases are environmentally hazardous and contain nitrogen atom in the molecule. However, it seems that their sensing mechanism in electrocatalytic sensor could be totally different. Namely, the maximum sensitivity for each gas was obtained at different temperatures. Also, different auxiliary layers are formed...
-
Pr-doped TiO2: The effect of metal content on photocatalytic activity
PublikacjaThe Pr-TiO2 nanoparticles were prepared by using the sol-gel method. As-prepared samples were characterized by BET measurements, X-ray powder diffraction analysis (XRD) and UV-Vis spectra. Visible and ultraviolet light photocatalytic activity of the sample was studied by photodegradation of phenol while considering the influence of the dopant concentration. TiO2 doped with 0.25 mol% of praseodymium showed the highest photocatalytic...
-
PROPERTIES OF DOPED ALKALINE-EARTH STANNATES
PublikacjaThe lanthanum doped barium stannate properties are investigated in this work. Including electrical and microstructural properties.
-
RARE-EARTH ELEMENTS DOPING OF BARIUM CERATE AND ZIRCONATE SOLID SOLUTION
PublikacjaThe properties of doped barium cerate barium zirconate solid solution are presented in presented work. It was found that doping of solid solution of barium cerate and zirconate by rare-earth elements have an influence on microstructure and electrical properties of the samples.
-
Rigid polyurethane foams modified with selected layered silicate nanofillers
PublikacjaThe aim of this study was to investigate the effect of three different nanofillers on the properties of rigid polyurethane foams, which were prepared by a one-step, laboratory-scale method from a two-component system at the ratio of NCO groups to OH groups equaled to 2. The reaction mixture consisted of the proper amounts of the commercial oligoether polyol, catalysts, water, nanoclays, and polymeric diphenylmethane diisocyanate....
-
Thermal decomposition of [Cd{SSi(OBut)3}(S2CNC4H8)]2 to CdS “micro-noodles”
PublikacjaThis work presents studies on thermal degradation of novel heteroleptic complex possessing mixed S-donor ligands, [Cd{SSi(OBut)3}(S2CNC4H8)]2 using TGA, DSC, TGA-IR, SEM and XRD methods.
-
Thermal treatment of montmorillonite modified with Cd[SC(NH2)2]42+ from two polymorphic salts
PublikacjaMontmorillonite(MMT)/CdS nanocomposites can be obtained using simple ionic exchange between Na(I)-MMT and Cd[SC(NH2)2]42+∙2NO3. The resulting products may be annealed to give (MMT)/CdS nanocomposites as it was proved by XRD analysis.
-
YSZ Thin film deposited on porous substrate by spray pyrolysis
PublikacjaIn this work the results of deposition of YSZ layer on a porous substrate using an ultrasonic Spray Pyrolysis are presented.
Rok 2012
-
Cavitation Erosion Resistance of Austenitic Stainless Steel after Glow-Discharge Nitriding Process
PublikacjaThis paper presents investigation of cavitation erosion resistance of nitrided austenitic stainless steel X5CrNi18-10. The diffusion layers were produced by using different parameters of atmosphere (N2:H2). The microstructure, chemical composition and phase identification of the modified layer were examined using scanning electron microscopy, glow-discharge optical emission spectrometer and X-ray diffractometry, respectively. Cavitation...
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublikacjaNonstoichiometric Nb-substituted SrTiO3 compounds were investigated in order to discuss the influence of nonstoichiometry at the sample properties in the light of recent results reported in the literature. Structural and electrical properties of samples were characterized. Investigated compounds were also applied as anodes for Solid Oxide Fuel Cells and their reactivity with YSZ electrolyte was examined. The defect chemistry explaining...
-
Donor-substituted SrTi1+xO3−δ anodes for SOFC
PublikacjaPrzebadano wpływ niestechiometrii na właściwości tytanianu strontu domieszkowanego niobem. Zaproponowano chemię defektów dla tego typu związków.
-
Ferromagnetic nanocrystallites in the SiO2 - PbO - Fe2O3 glass system
PublikacjaThe structure of 50% SiO2 - 35% PbO - 15% Fe2O3, 50% SiO2 - 30% PbO - 20% Fe2O3 and 50% SiO2 - 25% PbO - 25% Fe2O3 (in mol%) glass was investigated by the means of AFM microscopy and X-ray diffraction. Observation by the atomic force microscopy shows that each of prepared iron oxide glass doesn't have homogeneous structure and some nanocrystallites were detected. Next, test with neodymium magnet found out strong magnetic properties...