Wyszukiwarka
Filtry
wszystkich: 12
Wyniki wyszukiwania dla: FLAT GRINDING
-
Correlation between shape errors in flat grinding
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych i symulacyjnych związanych z wpływem błędów kształtu narzędzia na błędy ksztaltu przedmiotu szlifowanego w układzie docierarki jednotarczowej. Szlifowanie realizowane było z wykorzystaniem specjalnych narzędzi z możliwością regulacji przekroju promieniowego.
-
Wear of Electroplated Tools Used for Flat Grinding of Ceramics
PublikacjaTwo methods for the abrasive properties evaluation, based on the image processing, are presented in the paper. Image processing analysis was developed to evaluate quickly the abrasive properties as the tool wears down. The coefficient based on the image brightness was calculated and additional analysis was based on the number of grains located on the active surface of the tool before and after machining. The active surfaces of...
-
Analysis of Roughness, the Material Removal Rate, and the Acoustic Emission Signal Obtained in Flat Grinding Processes
PublikacjaIn this work, the analysis of the acoustic emission (AE) signal in grinding processes is addressed. The proposed analysis method decomposes the acoustic signal into three frequency ranges. The total energy of each range is determined, as well as the highest frequency. Different grinding experiments were carried out, according to a full factorial design of experiments (DOE), in which feed speed, depth of cut, and transversal step...
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublikacjaNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Vertical vibration reduction and audible sound analysis in surface grinding with electroplated tools
PublikacjaOne of the first approaches to the development of a grinding process monitoring system based on audible sound sensors is presented in the paper. Electroplated diamond tools (abrasive D64 and D107) were used in a modified single-disc lapping machine configuration for flat grinding of ceramics (Al2O3). The main aim of the machine modification was to reduce the vertical vibration in order to decrease the tool wear and to increase...
-
Mariusz Deja dr hab. inż.
OsobyAdiunkt w Katedrze Technologii Maszyn i Automatyzacji Produkcji. Ukończył w 1993 roku studia wyższe magisterskie na Wydziale Mechanicznym Politechniki Gdańskiej, kierunek: Mechanika i Budowa Maszyn, specjalność: Projektowanie Procesów Technologicznych. Po ukończeniu studiów podjął pracę w Katedrze Technologii Maszyn i Automatyzacji Produkcji, a jego podstawowy obszar działalności naukowej związany był z technologią docierania...
-
The effect of tyre rubber grinding method on the rubber-asphalt binder properties
PublikacjaRubber products, especially those used in the automotive industry, are responsible for a significant amount of waste, mainly in the form of worn tyres. One way to recycle tyres is to use them as an asphalt binder modifier. The properties of rubber-asphalt binders vary greatly depending on the morphology of the ground tyre rubber (GTR) grains and the type of tyre to be recycled (car/truck). The paper presents the results of research...
-
Microgrinding with single-disk lapping kinematics.
PublikacjaGrinding operations are carried out with a variety of tool-workpiece configurations. The selection of a grinding process for a particular application depends on part shape, part size, ease of fixture, requirements concerning the acceptable shape errors. It is evident that lapping is very effective in eliminating the waviness while surface grinding is not. Dual disk machines for the double face grinding with planetary kinematics...
-
The Impact of Material Selection on Durability of Exhaust Valve Faces of a Ship Engine – A Case Study
Publikacjawo alloys were used in order to extend the service life of marine engine exhaust valve head. Layers of cobalt base alloys were made of the powders with with chemical composition as follow: the layer marked L12; C-1,55%; Si-1,21%; Cr-29,7%; W-9%; Ni-2%; Mo<0,01%; Fe-1,7%; Co-54,83% and the layer marked N; C-1,45%; Co-38,9%; Cr-24,13%; Ni-10,43%; W-8,75%; Fe-7,64%; Mo-7,56%; Si-2,59%. Base metal was valve steel after heat treatment....
-
The influence of rubber recyclate morphology on the properties of rubber-asphalt composite
PublikacjaIn the paper wastes, mostly in the form of used tires, were analyzed. One of the methods of waste tires application use them as a modifier of asphalt. However, the properties of rubber-asphalt composites depend on the morphology of waste tiregranulate and kind of tire recycled (car/truck). In this chapter, the influence of grinding methods of waste tire on the prop¬erties of rubber-asphalt composites were studied. SEM analysis...
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublikacjaCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
Influence and development of new kinematic systems in flat surface lapping
PublikacjaThe face grinding and lapping technology is widely used in the field of the precise and ultraprecise manufacturing. It has become an indispensable technology in the manufacture of many parts. An absence of material restrictions allows machining both metal and non-metallic materials, including technical ceramics [1]. Nowadays there are mainly two kinematic systems in lapping machines [2]. The machining plane-parallel surfaces is...