Publikacje
Filtry
wszystkich: 387
Katalog Publikacji
Rok 2021
-
Analysis of Failure Mechanism in Joints with Positive Eccentricity in CFS Truss
PublikacjaThe paper presents studies concerning the load-bearing capacity of truss joints with a positive eccentricity resulting from the arrangement of geometric members and the failure mechanisms observed in the joints. Based on the previously conducted experimental study, a numerical model of the tested fragment of the CFS truss with eccentricity in the joint was created and validated. All structural details of the tested truss and the...
-
Axial capacity of steel built-up battened columns
PublikacjaThis paper deals with the numerical investigation aimed to study the axial capacity of pin-ended steel built-up columns. Three methods of calculating forces in chords and batten, taking into account the material and geometric imperfections specified in the Eurocode 3 are considered. The aim of this study was to compare different methods allowing the calculation of the column load capacity and determine a simpler and faster method...
-
Effective Gap Size Index for Determination of Optimum Separation Distance Preventing Pounding between Buildings during Earthquakes
PublikacjaSeismic excitations may lead to collisions between adjacent civil engineering structures causing major damage. In this paper, an effective equation for calculating the gap size index is proposed so as to provide the optimum separation distance preventing structural pounding during different earthquakes. Evaluation of the best prediction of the required separation distance between two adjacent buildings was carried out by using...
-
Impact of Geometrical Imperfections on Estimation of Buckling and Limit Loads in a Silo Segment Using the Vibration Correlation Technique
PublikacjaThe paper examines effectiveness of the vibration correlation technique which allows determining the buckling or limit loads by means of measured natural frequencies of structures. A steel silo segment with a corrugated wall, stiffened with cold-formed channel section columns was analysed. The investigations included numerical analyses of: linear buckling, dynamic eigenvalue and geometrically static non-linear problems. Both perfect...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublikacjaIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublikacjaIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Zabezpieczenia antykorozyjne stalowych barierek ochronnych na obiektach mostowych w ujęciu kosztów cyklu ich życia
PublikacjaThe article presents the Life Cycle Costs analysis of steel safety barriers operated in road lane conditions, located on a selected bridge structure. Three corrosion protection systems were proposed, analyzing them in terms of the cost of initial and planned outlays related to maintenance. Based on the LCC analysis for three options, taking into account the 25-year lifetime of the barriers, the optimal solutionwas indicated, i.e....
Rok 2020
-
Analysis of Validation and Simplification of Timber-Frame Structure Design Stage with PU-Foam Insulation
PublikacjaThe transition from experimental studies to the realm of numerical simulations is often necessary for further studies, but very difficult at the same time. This is especially the case for extended seismic analysis and earthquake-resistant design. This paper describes an approach to moving from the experimental testing of an elementary part of a wood-frame building structure to a numerical model, with the use of a commercial engineering...
-
Corrugated Sheeting as a Member of a Shear Panel Under Repeated Load—Experimental Test
PublikacjaIn stressed-skin design, the cladding stiffening effect on structures is taken into account. However, the “traditional” design is more usual, wherein this effect is neglected. Even if the diaphragm actions are not regarded, in particular cases such as big sheds (and others), the parasitic (unwanted) stressed-skin action may occur with the result of leakage or even failure. The structures of this kind have already been built. Thus,...
-
Dynamic analysis of temporary steel grandstand subjected to human-induced excitations due to jumping
PublikacjaSteel grandstands are structures that are frequently used during sport games and many other non-sporting events, such as festivals, music concerts, or even politicians rallies, with participation of a large number of attendees. Unfortunately, the presence of unexpected excessive dynamic loads due to unpredictable behaviour of spectators (e.g. synchronized harmonic jumping or swaying) may lead to...
-
Experimental investigation of joint with positive eccentricity in CFS truss
PublikacjaDue to technological restrictions, in the case of trusses made of CFS open cross-sections, positive eccentricities in the truss joints have become very frequent. Therefore studies concerning the load-bearing capacity of truss joints with positive eccentricity were undertaken. It was assumed that the resistance of cold-formed steel (CFS) open cross-section truss joints located on compression chords and with positive eccentricity...
-
Experimental Study on the Effectiveness of Polyurethane Flexible Adhesive in Reduction of Structural Vibrations
PublikacjaThe aim of the present study is to consider the idea of using polyurethane flexible adhesive in to reduce the vibrations in structures exposed to dynamic loads and evaluate their damping properties in relation to large deformations. Firstly, two aluminium cantilever beams, simulating structural elements (without and with polyurethane layer in the form of tape), were analysed, in order to check the damping of the unconstrained polymer...
-
Modeling of wood frame structures with different insulation materials under damaging dynamic loading
PublikacjaWood frame buildings are very popular in regions that are exposed to different dynamic excitations, such as damaging earthquakes. Their seismic resistance is really important in order to prevent structural damages and human losses. This paper presents the results of advanced numerical investigation carried out using the FEM. Based on the models of wall panels, the numerical model of real structure of the wood frame building has...
-
Nonlinear numerical simulation of earthquake-induced pounding between timber frame buildings
PublikacjaEarthquakes may induce serious dynamic loads acting on buildings, which can lead to damage or even destruction of the whole structure. In densely populated areas, it is quite common that buildings are located very close one to another which can result in pounding between them during ground motions. Due to the environmental awareness, multi-story timber frame buildings are gaining popularity and therefore there is a need to investigate...
-
O historii i działalności Katedry Konstrukcji Metalowych Politechniki Gdańskiej
PublikacjaW artykule przedstawiono prowadzone w Katedrze Konstrukcji Metalowych badania naukowe, współpracę z przemysłem i działalność dydaktyczną od czasu jej powstania w 1945 r. po dzień dzisiejszy.
-
O wymiarowaniu kształtowników giętych na zimno według eurokodów i norm amerykańskich.
PublikacjaNośne konstrukcje z kształtowników giętych na zimno były wykorzystywane w przemyśle lotniczym i motoryzacyjnym od początku XX w. W obiektach budowlanych początkowo pełniły one rolę elementów konstrukcyjnych drugorzędnych, takich jak ościeżnice czy elementy ścian działowych. Obecnie są stosowane również jako główne elementy nośne w halach przemysłowych (słupy, wiązary, konstrukcje wsporcze dźwignic). Pręty cienkościenne, ze względu...
-
SHORT REVIEW AND 3-D FEM ANALYSIS OF BASIC TYPES OF FOUNDATION FOR OFFSHORE WIND TURBINES
PublikacjaSome problems of the foundations of offshore wind turbines are considered in this paper. A short review is presented on the two basic types of foundations, i.e. monopiles and gravity foundations, including their basic features and applications as well as general design considerations. Also, some issues regarding analysis are discussed, including geotechnical problems and modelling techniques. A numerical model of offshores turbine...
-
Uproszczone metody obliczania cylindrycznych silosów z blachy falistej i słupów cienkościennych
PublikacjaCelem artykułu jest wyznaczenie nośności wyboczeniowej trzech silosów wykonanych z falistej blachy ze sfałdowaniem w kierunku obwodowym, wzmocnionych słupami pionowymi stosując modele MES całych konstrukcji i ich segmentów oraz porównanie obliczonej nośności wyboczeniowej z Eurokodem 3, poprawkami do Eurokodu 3 i metodą zaproponowaną w literaturze. Nowym elementem analizowanym w pracy jest porównanie różnych metod analitycznych...
Rok 2019
-
Building Information Modeling in Small and Middle Sized Buildings – Case Study
PublikacjaBuilding Information Modeling (BIM) is a technology designed to improve and integrate all engineering aspects in the construction design process. Tools that incorporate the idea of BIM are becoming more advanced and also more popular. Available software solutions have already reached an assumable high level of development, but still are not as widespread and used on nearly as many construction projects as could be expected. Therefore...
-
Determination of buckling strength of silos composed of corrugated walls and thin-walled-columns using simplified wall segment models
PublikacjaW artykule przedstawiono wyniki obszernych analiz numerycznych wyboczenia i stateczności metalowych silosów z blachy falistej wzmocnionych cienkościennymi słupami. Wykonano analizy liniowe i nieliniowe. Do obliczeń zaproponowano proste modele segmentów ścian zamiast skomplikowanych modeli całych silosów. Otrzymano bardzo dobrą zgodność wyników numerycznych. Wyniki obliczeń numerycznych porównano dodatkowo z wynikami normowymi.