prof. dr hab. inż. Magdalena Rucka
Employment
- Head of Department at Katedra Wytrzymałości Materiałów
- Professor at Katedra Wytrzymałości Materiałów
- at Faculty of Civil and Environmental Engineering
Publications
Filters
total: 200
Catalog Publications
-
Experimental study on ultrasonic monitoring of splitting failure in reinforced concrete
PublicationThis paper investigates inspection of reinforced concrete elements sensitive to the splitting failure. The behaviour of a reinforced concrete specimen subjected to a tensile stress is considered. The damage detection procedure is based on the ultrasonic wave propagation technique. The piezoelectric transducers are located on both ends of the specimen and the measurements are taken periodically during the incrementally increased...
-
Modal properties identification of a novel sandwich footbridge – Comparison of measured dynamic response and FEA
PublicationA modern sandwich composite footbridge made of high-tech materials, being an example of practical application of laminated composites in civil engineering, is presented. The in situ non-destructive testing of the footbridge, aiming to identify modal properties and pedestrian comfort, is described. The measured eigenmodes and eigenfrequencies are compared with numerically estimated values. Finite element analyses of the footbridge...
-
Non-Destructive Assessment of Masonry Pillars using Ultrasonic Tomography
PublicationIn this paper, a condition assessment of masonry pillars is presented. Non-destructive tests were performed on an intact pillar as well as three pillars with internal inclusions in the form of a hole, a steel bar grouted by gypsum mortar, and a steel bar grouted by cement mortar. The inspection utilized ultrasonic stress waves and the reconstruction of the velocity distribution was performed by means of computed tomography. The...
-
Experimental and numerical studies of guided wave damage detection in bars with structural discontinuities
PublicationPraca dotyczy analizy propagacji fal podłużnych i poprzecznych w elementach prętowych z nieciągłościami strukturalnymi. Symulacje numeryczne przeprowadzone przy zastosowaniu metody elementów spektralnych zostały porównane z wynikami badań eksperymentalnych dla pręta w stanie nienaruszonym oraz dla prętów z rysą, spawem oraz dodatkową masą.
-
Guided ultrasonic waves for detection of debonding in bars partially embedded in grout
PublicationThis paper deals with theoretical, numerical and experimental investigations of guided wave propagation in multilayered cylindrical bars with pre-existing debonding. The research focuses on a complex description of the nature of the wave phenomena occurring in a debonded specimen with a special emphasis on the influence of the location of damage on the wave conversion and diffraction. Experimental non-destructive and destructive...
-
Experimental and theoretical investigations of silo music
PublicationW artykule przedstawiono wyniki doświadczalne i teoretyczne badania zjawiska muzyki silosowej podczas przepływów materiałów granulowanych w silosach. Badania dynamiczne i tomograficzne wykonane w modelu silosu napełnionego piaskiem. Obliczenia numeryczne wykonano przy zastosowaniu metody elementów skończonych i mikropolarnego modelu hipoplastycznego z uwzględnieniem dynamicznej interakcji ściany z piaskiem.
-
Wave Frequency Effects on Damage Imaging in Adhesive Joints Using Lamb Waves and RMS
PublicationStructural adhesive joints have numerous applications in many fields of industry. The gradual deterioration of adhesive material over time causes a possibility of unexpected failure and the need for non-destructive testing of existing joints. The Lamb wave propagation method is one of the most promising techniques for the damage identification of such connections. The aim of this study was experimental and numerical research on...
-
Guided waves for monitoring of plate structures with linear cracks of variable length
PublicationDamage occurring at the work of plate structures may grow to a considerable size. The joint action – the detection of a defect at the earliest possible stage, the monitoring of its growth and the determination of its critical size in the context of structural reliability allows optimizing the cost of the maintenance and repair of structural elements. Thus the development of monitoring systems for permanent observation of fault...
-
Damage Imaging in Lamb Wave-Based Inspection of Adhesive Joints
PublicationAdhesive bonding has become increasingly important in many industries. Non-destructive inspection of adhesive joints is essential for the condition assessment and maintenance of a structure containing such joints. The aim of this paper was the experimental investigation of the damage identification of a single lap adhesive joint of metal plate-like structures. Nine joints with different defects in the form of partial debonding...
-
Non-destructive inspection of ground anchors using guided wave propagation
PublicationThis paper deals with numerical and experimental investigations of specific problems of guided wave propagation in ground anchors. The research focuses on recognizing the phenomenon of the energy transfer between anchor components. Particular attention is paid to characteristic features of guided waves propagating in free and embedded parts of the tendon, at the interface between the tendon and the surrounding anchor body as well...
-
Modelling of in-plane wave propagation in a plate using spectral element method and Kane–Mindlin theory with application to damage detection
Publication -
On some properties of 2d spectral finite elements in problems of wave propagation
PublicationW pracy przedstawiono sformułowanie dwuwymiarowych elementów spektralnych stosowanych w symulacji propagacji fal prowadzonych. Zbadano własności tych elementów pod kątem występowania form pasożytniczych, odporności na dystorsję siatki oraz zbadano wpływ kształtu elementu na krzywe dyspersji
-
GPR investigation of the strengthening system of a historic masonry tower
PublicationIn this paper the condition assessment of the strengthening system of a masonry tower was carried out by the GPR method. The study provided unique experimental data acquired during measurements of the reinforced concrete frame embedded in masonry walls. Conducted numerical and experimental investigations were focused on the phenomenon of the diffraction-refraction scattering of the electromagnetic energy. A hyperbola resulting...
-
Detection of debonding in reinforced concrete beams using ultrasonic transmission tomography and hybrid ray tracing technique
PublicationThis paper concerns inspection of reinforced concrete elements, with particular emphasis on assessing the quality of the adhesive connection between steel and concrete. A novel theoretical model was developed to determine the paths of transmitted, refracted and reflected elastic waves as well as a creeping wave propagated along the inclusion surface. Imaging the internal structure of tested beams was based on wave propagation measurements...
-
Characterization of fracture process in polyolefin fibre-reinforced concrete using ultrasonic waves and digital image correlation
PublicationThis study explores the monitoring of the fracture process in concrete beams and aims to characterize the evolution of damage in polyolefin fibre-reinforced concrete beams by utilizing the integrated application of two measurement techniques, digital image correlation and ultrasonic testing. The interpretation of registered wave time histories data was provided by the calculation of the magnitude-phase-composite metrics. An efficient...
-
Ultrasound monitoring for evaluation of damage in reinforced concrete
PublicationThe paper deals with automated monitoring of damage evolution in concrete elements subjected to three-point bending tests. The monitoring is based on the nonlinear interactions of traveling ultrasonic waves with micro-crack zones inside the concrete specimens and surface-breaking cracks. The developed procedure assumes semi-continuous ultrasonic testing during the element full loading cycle and generation of the power spectral...
-
Failure Monitoring and Condition Assessment of Steel-Concrete Adhesive Connection Using Ultrasonic Waves
PublicationAdhesive bonding is increasingly being incorporated into civil engineering applications. Recently, the use of structural adhesives in steel-concrete composite systems is of particular interest. The aim of the study is an experimental investigation of the damage assessment of the connection between steel and concrete during mechanical degradation. Nine specimens consisted of a concrete cube and two adhesively bonded steel plates...
-
3-D finite-difference time-domain modelling of ground penetrating radar for identification of rebars in complex reinforced concrete structures
PublicationThis paper presents numerical and experimental investigations to identify reinforcing bars using the ground penetrating radar (GPR) method. A novel element of the paper is the inspection of different arrangements of reinforcement bars. Two particular problems, i.e. detection of few adjacent transverse bars and detection of a longitudinal bar located over or under transverse reinforcement, have been raised. An attention was also...
-
Non-Destructive Testing of a Sport Tribune under Synchronized Crowd-Induced Excitation Using Vibration Analysis
PublicationThis paper presents the concept of repairing the stand of a motorbike speedway stadium. The synchronized dancing of fans cheering during a meeting brought the stand into excessive resonance. The main goal of this research was to propose a method for the structural tuning of stadium stands. Non-destructive testing by vibration methods was conducted on a selected stand segment, the structure of which recurred on the remaining stadium...
-
Guided wave propagation for assessment of adhesive bonding between steel and concrete
PublicationAdhesive bonding is becoming more increasingly important in joining of structural elements. In civil engineering, there is a growing interest in connection by adhesive bonding in steel-concrete flexural members. This study concerns the guided wave propagation technique applied to condition assessment of an adhesive connection between a steel member and a concrete beam. Various states of degradation were considered by producing...
-
Monitoring the curing process of epoxy adhesive using ultrasound and Lamb wave dispersion curves
PublicationMonitoring the stiffness of adhesives is a crucial issue when considering the durability andstrength of adhesive joints. While there are many studies conducted on specimens madeonly from adhesive, the problem of curing of an adhesive film in real joints is moderatelyconsidered. This paper presents the monitoring of stiffening of epoxy adhesive using ultra-sound. Ultrasonic pulse velocity method was firstly applied for monitoring...
-
A novel heterogeneous model of concrete for numerical modelling of ground penetrating radar
PublicationThe ground penetrating radar (GPR) method has increasingly been applied in the non-destructive testing of reinforced concrete structures. The most common approach to the modelling of radar waves is to consider concrete as a homogeneous material. This paper proposes a novel, heterogeneous, numerical model of concrete for exhaustive interpretation of GPR data. An algorithm for determining the substitute values of the material constants...
-
Tensile failure study of 3D printed PLA using DIC technique and FEM analysis
PublicationThe paper presents the experimental and numerical study of the failure behaviour of Fused Filament Fabricated (FFF) Polylactic Acid (PLA) samples subjected to tensile load. The examined samples are printed in flat orientation with 0◦, 45◦ and 90◦ raster angles. During the experiments the deformation of the specimens is continuously scanned with the 3D Aramis measuring system utilizing the digital imaging correlation technique,...
-
Special Issue: “Non-Destructive Testing of Structures”
Publication -
Interpolation methods in GPR tomographic imaging of linear and volume anomalies for cultural heritage diagnostics
PublicationThis paper presents results of a ground penetrating radar (GPR) survey conducted in St. Joseph’s Church in Gdańsk, Poland. The aim of the study was to produce tomographic imaging of a renovated floor as well as the objects buried under the floor to detect linear and volume inclusions. The assumed track spacing was meaningfully greater than the single signal spacing in each track, which induced the need for interpolation methods...
-
Diagnostics of pillars in St. Mary’s Church (Gdańsk, Poland) using the GPR method
PublicationThe main goal of this study was non-destructive evaluation of pillars in the St. Mary’s Church (Gdańsk, Poland) using the ground penetrating radar (GPR) technique. The GPR inspection was conducted on four brick masonry pillars and five pillars strengthened by reinforced concrete jacketing. Data were acquired with a 2 GHz antenna along longitudinal and transverse profiles. The study involved the estimation of the electromagnetic...
-
Monitoring Steel Bolted Joints during a Monotonic Tensile Test Using Linear and Nonlinear Lamb Wave Methods: A Feasibility Study
PublicationThe structural integrity of steel bolted joints may be compromised due to excessive loading. Therefore, condition assessment and the detection of potential defects before they cause a failure have become a major issue. The paper is focused on the condition monitoring of a bolted lap joint subjected to progressive degradation in a tensile test. The inspection used Lamb waves propagated through the overlap area. Wave propagation...
-
Damage imaging algorithm for non-destructive inspection of CFRP/steel adhesive joints based on ultrasonic guided wave propagation
PublicationThe paper concerns assessing the quality of the adhesive connection between a steel plate and the reinforcing CFRP laminate. A three-stage algorithm for non-destructive damage imaging was developed. As the first step, an initial study involving dispersion curves of joint components was executed to determine the material parameters and the appropriate excitation frequency. During the second step, damage identification in three-layer...
-
Application of guided wave propagation in diagnostics of steel bridge components
PublicationEarly detection of potential defects and identification of their location are necessary to ensure safe, reliable and long-term use of engineering structures. Non-destructive diagnostic tests based on guided wave propagation are becoming more popular because of the possibility to inspect large areas during a single measurement with a small number of sensors. The aim of this study is the application of guided wave propagation in...
-
Detection and Imaging of Debonding in Adhesive Joints of Concrete Beams Strengthened with Steel Plates Using Guided Waves and Weighted Root Mean Square
PublicationStrengthening of engineering structures is an important issue, especially for elements subjected to variable loads. In the case of concrete beams or slabs, one of the most popular approaches assumes mounting an external reinforcement in the form of steel or composite elements by structural adhesives. A significant disadvantage of adhesive joints is the lack of access to the adhesive film for visual condition assessment, thus, there...
-
Monitoring the fracture process of concrete during splitting using integrated ultrasonic coda wave interferometry, digital image correlation and X-ray micro-computed tomography
PublicationThe paper deals with the continuous-time monitoring of mechanical degradation in concrete cubes under splitting. A series of experiments performed with integrated coda wave interferometry (CWI) and digital image correlation (DIC), supported with X-ray micro-computed tomography (micro-CT) is reported. DIC and micro-CT techniques were used to characterize the fracture process in detail. CWI method was proved to be effective in the...
-
Non-Destructive Diagnostics of Concrete Beams Strengthened with Steel Plates Using Modal Analysis and Wavelet Transform
PublicationExternally bonded reinforcements are commonly and widely used in civil engineering objects made of concrete to increase the structure load capacity or to minimize the negative effects of long-term operation and possible defects. The quality of adhesive bonding between a strengthened structure and steel or composite elements is essential for effective reinforcement; therefore, there is a need for non-destructive diagnostics of adhesive...
-
Imaging of Increasing Damage in Steel Plates Using Lamb Waves and Ultrasound Computed Tomography
PublicationThis paper concerns inspection of steel plates, with particular emphasis on the assessment of in-creasing damage. Non-destructive tests were performed on four plates, one of which was un-damaged, while the remaining three had a defects in the form of circular holes with a diameter of 2, 5, and 10 cm. Guided Lamb waves were used in the research, and the image reconstruction was performed using ultrasound computed tomography. The...
-
Damage detection in a bolted lap joint using guided waves
PublicationThe paper presents the experimental investigation of guided waves application to the condition assessment of prestressed bolted connections and a concept of new quantitative indicator. The main goal of the research was the analysis of the influence of the contact conditions changes to the characteristics of a propagating disturbance. The experimental tests were carried out for a single bolted lap joint. The excitation and acquisition...
-
Integrated Application of GPR and Ultrasonic Testing in the Diagnostics of a Historical Floor
PublicationThe paper presents the results of integrated ground penetrating radar (GPR) and ultrasonic testing (UT) measurements conducted on a historical floor in St. Nicholas’ Church, Gdańsk, Poland. The described inspection was the first stage of the technical state assessment of the building. The aim of the study was the detection of underfloor air gaps, which were observed in a few trial pits. The condition of the ground under the floor...
-
Internal imaging of concrete fracture based on elastic waves and ultrasound computed tomography
PublicationThe condition assessment of concrete structures belongs to the greatest challenges of non-destructive testing. Monitoring the fracture process of concrete and detecting cracks at the earliest possible stage is a vital aspect to ensure the safety of civil engineering objects. The use of ultrasound tomography enables imaging the internal structure of a tested element. This study aims at the visualization of fracture damage in concrete...
-
Research on assessment of bolted joint state using elastic wave propagation
PublicationThe work contains results of experimental investigation of elastic wave propagation in a bolted single-lap joint. Tests were carried out for the excitation perpendicular to the connection plane. In experimental studies, PZT transducers were used for both excitation and registration of ultrasonic waves. The analyses took into account varying contact conditions between the elements of the connection depending on the value of the...
-
Microcrack monitoring and fracture evolution of polyolefin and steel fibre concrete beams using integrated acoustic emission and digital image correlation techniques
PublicationThe use of polymer and steel fibres in plain concrete appears to be an excellent solution for limiting crack propagation and improving the post-ductility performance of concrete structures. Based on this premise, this study investigated the fracture evolution of polyolefin fibre-reinforced concrete (PFRC) and steel fibre-reinforced concrete (SFRC) specimens through the integrated application of two diagnostic techniques, acoustic...
-
Wave propagation in damage assessment of ground anchors
PublicationThe inspection possibilities of ground anchors are limited to destructive test such as pull-out test. Guided wave propagation gives an opportunity to develop an inspection system dedicated to determine the condition of inspected element without violation of their integrity. In this paper the experimental study on wave propagation in laboratory models of ground anchors are presented. Experiments were conducted for different bonding...
-
Assessment of Wooden Beams from Historical Buildings Using Ultrasonic Transmission Tomography
PublicationThe main goal of this study was non-destructive evaluation of wooden elements using ultrasonic waves. The inspection was carried out on wooden beams from a historical object. Elastic wave signals were processed by ultrasonic transmission tomography to obtain imaging of the internal structure of tested elements without disturbing their state and integrity. The focus was on the influence of wood anisotropy on the propagation of ultrasonic...
-
Preload monitoring in a bolted joint using Lamb wave energy
PublicationThe knowledge of the load in prestressed bolted connections is essential for the proper operation and safety of engineering structures. Recently, bolted joints have become an area of intensive research associated with non-destructive diagnostics, in particular in the context of wave propagation techniques. In this paper, a novel procedure of bolt load estimation based on the energy of Lamb wave signals was proposed. Experimental...
-
Elastic wave propagation for condition assessment of steel bar embedded in mortar
PublicationThis study deals with experimental and numerical investigations of elastic wave propagation in steel bars partially embedded in mortar. The bars with different bonding lengths were tested. Two types of damage were considered: damage of the steel bar and damage of the mortar. Longitudinal waves were excited by a piezoelectric actuator and a vibrometer was used to non-contact measurements of velocity signals. Numerical calculations...
-
Damage detection of a T-shaped panel by wave propagation analysis in the plane stress
PublicationW pracy zaprezentowano podejście obliczeniowe do analizy propagacji fal w płaskim stanie naprężenia. Problem brzegowo-początkowy podlega przestrzennej aproksymacji z użyciem wielowęzłowych, izoparametrycznych, czworobocznych elementów klasy C0. Macierze elementowe są całkowane numerycznie za pomocą kwadratury Gauss-Legendre-Lobatto. Aproksymację w dziedzinie czasu wykonano za pomocą algorytmu Newmarka. Symulacje numeryczne przeprowadzono...
-
Experimental and numerical investigations for GPR evaluation of reinforced concrete footbridge
PublicationThe GPR method has increasingly found application in non-destructive testing of reinforced concrete structures. This paper presents the new approach of modelling of the electromagnetic wave propagation for reinforced concrete structures with a complex system of the reinforcement. Simulations of the GPR field were performed on a three-dimensional model of a footbridge using the FDTD method. Numerical maps were compared with results...
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublicationThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
Modelling of Mechanical Behaviour of High-Frequency Piezoelectric Actuators Using Bouc-Wen Model
PublicationThe paper presents the application of a modified, symmetrical Bouc-Wen model to simulate a mechanical behaviour of high-frequency piezoelectric actuators (PAs). In order to identify parameters of the model, a two-step algorithm was utilized. In the first stage, the mechanical parameters were identified by taking into account their bilinear variability and using a square input voltage waveform. In the second step, the hysteresis...
-
A concept of heterogeneous numerical model of concrete for GPR simulations
PublicationThe Ground Penetrating Radar (GPR) method, which is increasingly being used in the non-destructive diagnostics of reinforced concrete structures, often needs more accurate interpretation tools for analysis of experimental data. Recently, there has been growing interest in developing of various numerical models for exhaustive understanding of GPR data. This paper presents the concept of a heterogeneous numerical model of concrete,...
-
The effect of external load on ultrasonic wave attenuation in steel bars under bending stresses
PublicationThe stress state in deformed solids has a significant impact on the attenuation of an ultrasonic wave propagating through the medium. Measuring a signal with certain attenuation characteristics can therefore provide useful diagnostic information about the stress state in the structure. In this work, basic principles behind a novel attenuation-based diagnostic framework are introduced. An experimental study on steel bars under three-point...
-
Medially positioned plate in first metatarsophalangeal joint arthrodesis
PublicationObjective The purpose of this study was to biomechanically compare the stability of first metatarsophalangeal (MTP1) joint arthrodesis with dorsally and medially positioned plates. Methods A physical model of the MTP1 joint consists of printed synthetic bones, a titanium locking plate and screws. In the experiments, samples with dorsally and medially positioned plates were subjected to loading of ground load character in a universal...
-
Lamb wave-based monitoring of shear failure of an adhesive lap joint
PublicationThe paper presents a study on the elastic wave propagation in adhesive joints of steel plates subjected to tensile loading. A single lap joint was chosen for analysis because of its simplicity and plurality of applications. Experimental investigations consisted of the uniaxial extension of prepared specimens. Force and displacement values were recorded by a testing machine. Simultaneously, guided Lamb waves were excited and signals...
-
Non-destructive Testing of Wooden Elements
PublicationExamining the condition of wooden elements is crucial from the perspective of proper structure performance. If the deterioration in the internal wood condition, which displays no symptoms visible from the outside, is detected, the further spread of the deterioration can be prevented. Test results often point to the necessity of conducting repairs and, renovations, replacing the structure of wooden beams, or even substituting a...
-
Bolted Joint Monitoring Using the Elastic Wave Propagation
Publication -
DYNAMIC RESPONSE OF FORUM GDANSK STRUCTURE DUE TO RAIL TRAFFIC
PublicationThe paper presents the study of the impact of vibration induced by the movement of the railway rolling stock on the Forum Gdańsk structure. This object is currently under construction and is located over the railway tracks in the vicinity of the Gdańsk Główny and Gdańsk Śródmieście railway stations. The analysis covers the influence of vibrations on the structure itself and on the people within. The in situ measurements on existing...
-
Modelling of Longitudinal Elastic Wave Propagation in a Steel Rod Using the Discrete Element Method
PublicationThe paper deals with the issue of modelling elastic wave propagation using the discrete element method (DEM). The case of a longitudinal wave in a rod with a circular cross-section was considered. A novel, complex algorithm consisting of the preparation of models and simulation of elastic waves was developed. A series of DEM models were prepared for simulations, differing in discretisation and material parameters. Additional calculations...
-
Dynamic Tests and Technical Monitoring of a Novel Sandwich Footbridge
PublicationA novel sandwich composite footbridge is described in this paper, for the first time after it has been put into operation over the Radunia River in the Pruszcz Gdański municipality. This paper presents results of dynamic tests and describes technical monitoring of the footbridge. The dynamic tests were conducted to estimate pedestrian comfort and were compared with the ones from numerical simulations made in the environment of...
-
Composite sandwich footbridge—measured dynamic response vs. FEA
Publication -
Lamb wave propagation in a single lap adhesive joint
Publication -
A study on microcrack monitoring in concrete: discrete element method simulations of acoustic emission for non-destructive diagnostics
PublicationThe research is focused on the monitoring of fracture evolution in concrete beams under three-point bending using the acoustic emission technique and the discrete element method. The main objective of the study was to numerically and experimentally investigate the mechanism behind the generation of elastic waves during acoustic emission events and their interaction with micro- and macro-cracking in concrete beams under monotonic...
-
Failure characterisation of sandwich beams using integrated acoustic emission and digital image correlation techniques
PublicationThe paper presents the experimental study of the failure behaviour of sandwich beams subjected to bending. The samples examined are sandwich beams made of polyethylene terephthalate foam core and glass fibre-reinforced polymer laminate face sheets. In a series of experiments, it has been proposed to integrate diagnostic techniques with acoustic emission and digital image correlation to accurately track the cracking process on the...
-
Detection of debonding in adhesive joints using Lamb wave propagation
PublicationAdhesively bonded joints are widely used in many branches of industry. Mechanical degradation of this type of connections does not have significant symptoms that can be noticed during visual assessment, so non-destructive testing becomes a very important issue. The paper deals with experimental investigations of adhesively bonded steel plates with different defects. Five samples (an intact one and four with damages in the form...
-
Ultrasonic Tomography of Brick Columns Based on FEM Calculations
PublicationUltrasonic tomography is one of the most developed method of non-destructive testing. Despite being used mainly in medicine, it is becoming more and more popular as a method for monitoring of structural elements. It allows to examine the internal structure and technical condition of the tested element. This paper investigates the influence of crosssectional geometry on an obtained tomographic image. Wave propagation signals were...
-
Wybrane metody wzmacniania ceglanych obiektów zabytkowych.
PublicationWzmacnianie konstrukcji murowych stanowi jedno z najbardziej istotnych przedsięwzięć w dziedzinie utrwalania zabytków. Licznie prowadzone badania potwierdzają, że prawidłowo zaplanowane oraz wykonane wzmocnie nie uszkodzonej konstrukcji murowej obiektu zabytkowego pozwala na jego stabilizację i właściwe funkcjonowanie. W artykule zaprezentowano wybrane metody wzmacniania ceglanych konstrukcji obiektów zabytkowych. Przedstawiono...
-
Modelling of elastic wave propagation in a bolted joint using a thin layer of shell elements
PublicationThere are many mathematical models describing the propagation of elastic waves through the imperfect boundary of two media. They were successfully applied to modelling of high frequency bulk waves and their interaction with local defects. On the other hand, the existing literature models of bolted connections ignore the aspect of imperfect connection between elements. Therefore, this paper presents the concept of application of...
-
Experimental and numerical analysis of wave propagation in ground anchors
PublicationThe article focuses on wave propagation phenomenon in ground anchors. The main aim of the investigation is the non-destructive diagnostics and the assessment of the state of ground anchors, using the guided wave propagation method. Laboratory models of anchors with different lengths of the anchor body were tested and voltage signals of propagating waves were registered at several locations. For all tested specimens corresponding...
-
Using the ultrasonic tomography method to study the condition of wooden beams from historical buildngs
PublicationThe need to evaluate the integrity of wooden structural elements is constantly increasing. Non-destructive methods are becoming more popular in this field of research. One type of non-destructive testing is the ultrasonic imaging method, which allows the analysis of internal wood structures without disturbing their state and integrity. In this study, we are interested in assessing the effect of wood condition on the ultrasound...
-
Wybrane metody badań nieniszczących na przykładzie diagnostyki mostowego dźwigara kablobetonowego
PublicationSystemy monitoringu technicznego oraz badania nieniszczące stanowią podstawę nowoczesnej diagnostyki konstrukcji, umożliwiając ocenę aktualnego stanu obiektów budowlanych, a także wykrycie zagrożeń mających wpływ na zachowanie stanu granicznego nośności oraz użytkowalności głównych elementów konstrukcyjnych. Możliwość przeprowadzenia pomiarów in situ, niejednokrotnie wspieranych zaawansowanymi analizami numerycznymi, wprowadza...
-
Identyfikacja prędkości fali elektromagnetycznej w przegrodach budowlanych diagnozowanych metodą georadarową
PublicationPraca jest poświęcona metodzie identyfikacji prędkości fali elek-tromagnetycznej na podstawie analiz dyfrakcji spowodowanych obecnością inkluzji w przegrodach budowlanych żelbetowych, ceglanych oraz zespolonych żelbetowo-ceglanych. Wyprowadzono trzy modele matematyczne opisujące dyfrakcje charakterystyczne dla inkluzji kołowej, pionowej inkluzji przy powierzchni skanowa-nia oraz granicy między dwoma ośrodkami, w którym jednym z...
-
Macierzowa analiza konstrukcji prętowych w środowisku MATLAB®
PublicationNiniejsza książka poświęcona jest metodzie przemieszeń w ujęciu macierzowym, znanej także pod nazwą bezpośredniej lub komputerowej metody przemieszczeń. Podejście to jest szczególnym przypadkiem metody elementów skończonych (MES), która jest od wielu lat powszechnie stosowana w działalności inżynierskiej, w tym do analizowania różnorodnych problemów mechaniki. Metoda przemieszczeń jest dedykowana rozwiązywaniu układów prętowych....
-
Opracowanie opinii technicznej w zakresie występowania iniektu wewnątrz wskazanych przez Zleceniodawcę kanałów kablowych mostu MA-09 w ciągu drogi S7
PublicationCelem opracowania jest ocena występowania iniektu wewnątrz wskazanych przez Zleceniodawcę kanałów kablowych mostu MA-09 realizowanego w ramach zadania „Budowa drogi S-7 Gdańsk (A-1) – Elbląg (S-22) odc. Koszwały (DK nr 7, W. Koszwały) - Elbląg (z węzłem Kazimierzowo) z podziałem na 2 części. Zadanie 1: Koszwały – Nowy Dwór Gdański“. Zakres opracowania obejmuje: • zapoznanie się z dokumentacją techniczną obiektu, • wizję lokalną, •...
-
Special Issue: “Non-Destructive Testing of Structures”
PublicationThe Special Issue “Non-Destructive Testing of Structures” has been proposed to present recent developments in the field of diagnostics of structural materials and components in civil and mechanical engineering. The papers highlighted in this editorial concern various aspects of non-invasive diagnostics, including such topics as condition assessments of civil and mechanical structures and connections of structural elements, the...
-
Pomiary georadarowe posadzki w Bazylice pw. Świętego Mikołaja w Gdańsku
PublicationCelem opracowania są badania diagnostyczne posadzki kościoła w poszukiwaniu pustek powietrznych w konstrukcji podłogi. Badania przeprowadzono przy użyciu metody georadarowej. Przeanalizowano oraz przedstawiono szczegółowe skany georadarowe powierzchni posadzki. Jako uzupełnienie badań georadarowych, w wybranych miejscach zastosowano metodę ultradźwiękową.
-
Badania diagnostyczne posadzki w Bazylice św. Mikołaja w Gdańsku
PublicationZmiany warunków otoczenia obiektów zabytkowych, do których można zaliczyć industrializację otoczenia, ruch pojazdów mechanicznych, zanieczyszczenie środowiska oraz okresowe zmiany poziomu wód gruntowych, mają niejednokrotnie negatywny wpływ na ich stan techniczny. W przypadku pojawienia się pierwszych oznak uszkodzeń elementów konstrukcyjnych lub wykończeniowych, ocena wpływu poszczególnych czynników jest utrudniona, w szczególności,...
-
Guided Waves in Steel Rails – Experimental Works and Wavelet Signal Processing
Publication -
Application of guided waves in the evaluation of steel-concrete adhesive connection
Publication -
Elastic wave propagation in frame structure in the context of structural health monitoring
PublicationPraca dotyczy propagacji fal sprężystych r konstrukcji ramowej w ośrodku typu belka Timoszenki. Do obliczeń numerycznych wykorzystano wielowęzłowe spektralne elementy skończone klasy C0. Omówiono algorytm całkowania po czasie i sformułowano wnioski dotyczące liczby węzłów na długość fali.
-
Modelling of wave propagation in spatial frame elements - numerical simulations and experimental works
PublicationW pracy porównano rozwiązania propagacji fal sprężystych w ośrodku typu belka Timoszenki, uzyskane na drodze eksperymentalnej i numerycznej. Do obliczeń numerycznych wykorzystano wielowęzłowe spektralne elementy skończone klasy C0.Omówiono algorytm całkowania po czasie i sformułowano wnioski dotyczące liczby węzłów na długość fali.
-
Guided waves in steel rails - experimental works and wavelet signal processing
PublicationW artykule zaprezentowano analizę falkową pomierzonych eksperymentalnie fal sprężystych wzbudzanych w szynach kolejowych.
-
Application of wavelet analysis in damage detection and localization
PublicationWykrywanie i lokalizacja uszkodzeń w konstrukcjach inżynierskich są przedmiotem intensyw-nych badań z powodu ich praktycznego znaczenia. Niezwykle istotne jest wczesne wykrycie uszko-dzeń w konstrukcjach inżynierskich o szczególnym znaczeniu, ponieważ ich propagacja może do-prowadzić do katastrofy budowlanej. Stosunkowo nową dziedziną badań w wykrywaniu zniszczeń jest zastosowanie analizy falkowej. Metoda ta bazuje na postaciach...
-
Wielopoziomowy system diagnostyki konstrukcji. Badania eksperymentalne na płycie stalowej
PublicationCelem pracy jest zweryfikowanie przydatności systemu wykrywania uszkodzeń bazującego na sieciach neuronowych i testach dynamicznych. Analizowanie są dwa poziomy dynamicznego badania konstrukcji. Pierwszy poziom zakłada wykorzystanie drgań środowiskowych, zaś drugi wykorzystuje drgania wywołane siłami o znanych amplitudach i ma na celu szczegółową ocenę stalowej płyty. Uszkodzenie symulowano przez umieszczenie dodatkowej masy w...
-
Formulation of spectral truss element for guided waves damage detection in spatial steel trusses
PublicationW pracy przedstawiono sformułowanie wielowęzłowego elementu spektralnego oraz odpowiedniego schematu całkowania ukierunkowanego na problem propagacji fal w kratownicach przestrzennych o dowolnej geometrii. Zaproponowane podejście nie ogranicza liczby węzłów w elemencie kratowym. Porównawcze rozwiązania numeryczne przeprowadzono dla konstrukcji idealnej (w stanie nieuszkodzonym) oraz dlakonstrukcji z miejscową nieregularnością w...
-
Wave propagation analysis in spatial frames using spectral Timoshenko beam elements in the context of damage detection
PublicationPraca poświęcona jest zjawisku propagacji fal sprężystych w trójwymiarowych układach ramowych. W ramach teorii belek Timoszenki formułuje się wielowęzłowy element belkowy klasy C0 z sześcioma inżynierskimi stopniami swobody w każdym węźle. Zakłada się, że elementy są wykonane z jednorodnego, izotropowego materiału liniowo sprężystego. Zasadniczym celem artykułu jest sformułowanie szybkiego i wydajnego schematu całkowania po czasie....
-
System ciągłej obserwacji stanu technicznego hali ''Olivia'' w Gdańsku
PublicationCelem artykułu jest przedstawienie prototypowego syste-mu monitoringu technicznego zainstalowanego w Hali "Olivia" w Gdańsku. System określany jest nazwą "SMT OLIVIA-2". System został oddany do użytku 16 marca 2009 roku. System monitoringu technicznego "SMT OLIVIA-2" przeznaczony jest do zdalnego monitorowania podstawowych parametrów pracy konstrukcji dachu i w sposób zautomatyzowany sygnalizowanie o jej stanie technicznym. W przy-padku...
-
System monitoringu technicznego Hali Sportowo-Widowiskowej "Olivia" w Gdańsku (SMT OLIVIA-2)
PublicationSystem SMT OLIVIA-2 ma za zadanie monitorowanie podstawowych parametrów pracy konstrukcji dachu i w sposób zautomatyzowany sygnalizowanie o jej stanie technicznym. System jest nowatorskim rozwiązaniem technologicznym. Nowością w stosunku do dostępnych na rynku ofert jest w szczególności rozbudowany moduł obliczeniowy bazujący na szczegółowym modelu teoretycznym dachu oraz zintegrowany z nim system ekspercki.
-
Experimental and numerical study on damage detection in an L-joint using guided wave propagation
PublicationW pracy zaprezentowano metodę wykrywania i lokalizacji uszkodzeń w konstrukcji ramowej za pomocą podłużnych i poprzecznych fal sprężystych. Przeprowadzono badania numerczyne i eksperymentalne na modelu bez uszkodzenia oraz na modelu z wsprowadzonym nacięciem. Do modelowania zastosowano metodę elementów spektralnych. W pracy przedstawiono sformułowanie nowego element spektralnego dla ram płaskich bazującego na teorii pręta Mindlina...
-
Crack identification using wavelets on experimental staticdeflection profiles
PublicationArtykuł prezentuje metodę lokalizacji uszkodzeń w belce wspornikowej za pomocą transformaty falkowej statycznej linii ugięcia. Efektywnośc proponowanej techniki jest sprawdzona na podstawie badań eksperymentalnych. Do pomiaru statycznej linii ugięcia proponuje się metodę fotogrametryczną.
-
Application of continuous wavelet transform in vibration based damage detection method for beams and plates
PublicationW artykule zaprezentowano metodę lokalizacji uszkodzeń w konstrukcjach belkowych i płytowych bazującą na analizie falkowej. Wyznaczono postacie drgań badanych konstrukcji. Postacie drgań konstrukcji belkowej zostały przeanalizowane jednowymiarową transfrormatą falkową. Sformułowano dwuwymiarową transformatę falkową, którą zastosowano do postaci drgań konstrukcji płytowej.
-
Diagnostic system of cylindrical shell based on experimental modes and wavelet analysis
PublicationArtykuł poświęcony jest technice lokalizacji uszkodzeń w powłoce cylindrycznej. Na podstawie eksperymentalnie wyznaczonych postaci drgań oraz analizy falkowej wyznaczono miejsce uszkodzenia. Przedstawiono algorytm poszukiwania uszkodzeń poprzez zastosowanie sztycznej sieci neuronowej.
-
Application of time-frequency methods for analysis of dynamic silo flow
PublicationW artykule przedstawiono możliwość stosowania metod czasowo-częstotliwościowych w analizie dynamicznego przepływu materiału sypkiego w silosie. W pracy omówiono wyniki FT (Fourier Transform), STFT (Short Time Fourier Transform) oraz WT (Wavelet Transform)
-
Identyfikacja uszkodzeń płyt dwuwymiarową transformatą falkową eksperymentalnej postaci drgań
PublicationArtykuł poświęcony jest identyfikacji zniszczeń konstrukcji płytowych. Rozważano płytę z wprowadzonym defektem o powierzchni równej 2.4% powierzchni płyty i głębokości równej 25% jej grubości. Obliczono dwuwymiarową transformatę pierwszej postaci drgań wyznaczonej eksperymentalnie i numerycznie. Lokalizację defektu wskazuje lokalne ekstremum w przestrzennym rozkładzie modułów transformaty falkowej.
-
Damage location in beam and plate structures by wavelet analysis of experimentally determined mode shapes
PublicationArtykuł dotyczy zastosowania analizy falkowej do lokalizacji uszkodzeń w konstrukcjach belkowych i płytowych. Wykonano testy dynamiczne belki wspornikowej i płyty utwierdzonej wzdłuż jednej z krawędzi. Lokalizację defektu otrzymano za pomocą transformaty falkowej eksperymentalnie wyznaczonych postaci drgań.
-
Wavelet analysis in detection and localization of damage in engineering structures
Publication -
Damage detection in rectangular plates by continuous two-dimensional wavelet transform
PublicationPraca opisuje zastosowanie dwuwymiarowej transformaty falkowej do detekcji i lokalizacji uszkodzeń w konstrukcji płytowej. Defekt zlokalizowano na podstawie postaci drgań z symulacji numerycznych oraz z badań eksperymentalnych.
-
Characterization of Corrosion-Induced Fracture in Reinforced Concrete Beams Using Electrical Potential, Ultrasound and Low-Frequency Vibration
PublicationThe paper deals with the non-destructive experimental testing of the reinforced concrete beams under progressive corrosion. A series of experiments using electrical potential, ultrasound and low-frequency vibrations techniques are reported. Electrical potential and natural frequencies were used to characterise and monitor the corrosion process at its initial state. The P-wave velocity measurements were proved to be effective in...
-
Anisotropy and compaction gradient assessment on rammed earth specimens through sonic tomography approach
PublicationRammed earth is a traditional construction technique that has recently gained attention because of its benefits from an ecological perspective. The conservation of the existing valuable cultural heritage sites and the quality control of new constructions built with this material require the development and application of practical inspection techniques. This paper explores the application of sonic tests and sonic tomography as...
-
On using digital photos in a structure rehabilitation.
PublicationPraca dotyczy metody optycznego pomiaru ugięć w konstrukcjach inżynierskich na podstawie fotografii cyfrowych.
-
Identyfikacja zniszczeń belek poprzez transformatę falkową statycznej linii ugięcia.
PublicationW pracy przedstawiono technikę lokalizacji zniszczeń poprzez transformatę falkową statycznej linii ugięcia belki wspornikowej. Przedstawiono obliczenia bazujące na danych numerycznych i eksperymentalnych.Eksperymentalne pomiary ugięć wykonano metodą optyczną na podstawie forografii cyfrowych.
-
Numerical simulation of damage detection in rectangular plate by two-dimensional wavelet transform.
PublicationW pracy przedstawiono metodę lokalizacji pęknięć w płytach przy zastosowaniu transformaty falkowej.
-
Flatter jednoprzęsłowej wiszącej kładki dla pieszych
PublicationPrzedstawiono analizę aerodynamiczną stateczności wybranego typu wiszącej kładki dla pieszych z uwzględnieniem zjawiska flatteru i dywergencji.
-
Crack identification in cantilever beam using wavelets
PublicationPrzedstawiono metodę identyfikacji zniszczeń przy użyciu transformacji falkowej. Rozpatrzono przykład belki wspornikowej. Pokazano, że transformacja falkowa wykrywa miejsce zniszczenia.
-
Coda wave interferometry in monitoring the fracture process of concrete beams under bending test
PublicationEarly detection of damage is necessary for the safe and reliable use of civil engineering structures made of concrete. Recently, the identification of micro-cracks in concrete has become an area of growing interest, especially using wave-based techniques. In this paper, a non-destructive testing approach for the characterization of the fracture process was presented. Experimental tests were made on concrete beams subjected to mechanical...
seen 10173 times