Publications
Filters
total: 732
Catalog Publications
-
On degradation of glass/polyester laminate immersed in water
PublicationMechanical behaviour was compared for glass/ polyester laminates manufactured in the boatbuilding plant using three methods: hand lay-up, vacuum bagging, infusion. Specimens were tested in dry condition and following accelerated water immersion test (70°C- corresponding to the exposure of 30 years at 19°C). In three point bending test 40-50% reduction in laminate strength was observed due to water immersion. The highest degradation...
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublicationThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublicationThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
The influence of biological environment on the appearance of silver-coated implants
PublicationDespite antibiotics preventive treatment before and after implantation, risk of infection is real. The infections at the implant surface developein a few months after applying them into the body. To prevent the development of bacteria and to reduce the risk of infection, implants coated with silver layer come into use. The paper presents the research results in biological environment on vein and orthopaedicimplants covered with...
-
Kształtowanie właściwości warstwy wierzchniej podczas szlifowania
PublicationW artykule scharakteryzowano szlifowanie powierzchni płaskich połączone ze zmianami właściwości warstwy wierzchniej, zwłaszcza poprzez jej zahartowanie. Omówiono problemy związane z tzw. technologią grind-hardening. Dodatkowo przedstawiono badania, w których po procesie szlifowania uzyskano lepsze właściwości elementu obrabianego wskutek odkształcenia plastycznego.
-
Influence of Phase Composition on Dielectric Properties of Bismuth-Based Ceramics with Scheelite-Type Structure
PublicationGoal of the present research was to study dielectric properties of BiNbO4 ceramics fabricated by solid state reaction route followed with pressureless sintering. The samples were fabricated from the mixture of oxides, viz. Nb2O5 and Bi2O3. Apart from stoichiometric amount an excess of 3%, 5% and 10% by mole of Bi2O3 was used. It was found that an excess amount of Bi2O3 oxide caused formation of Bi5Nb3O15 minor phase in amount of...
-
Diffusible hydrogen content in deposited metal of multilayer welded joints
PublicationThe article describes manufacturing technology of multilayer joints in terms of control the diffusible hydrogen content. Diffusible hydrogen content in deposited metal for multilayer welded joints made of covered rutile electrodes or covered cellulosic and basic electrodes was determined. It was found that after four beads, the diffusible hydrogen content decreases in the case of the first technology from 36 ml/100 g to 18 ml/100...
-
Preliminary studies of seamless flux cored wires stored in extreme conditions
PublicationIn the paper preliminary experimental studies of flux cored wires moisturized under controlled conditions are described. Three seamless wires of different grades have been placed in environmental chamber and moisturized in extremely adverse conditions (temperature T = 60° C, relative humidity H = 90%) for 240 hours. During this time measurements of weight gain and observations of surface of wires have been carried out. Also diffusible...
-
Comparative in vitro research of the Human Aortic Bioprosthesis
PublicationE valuate of the usefulness and reliability of structures based on the analysis of recorded parameters determining the flow through the Human Aortic Bioprosthesis (HAB) have been dealt with. By flow parameters changes determining the performance environment of prosthesis analyzed change of the motion dynamics of the valve leaflets as a function of pressure, thereby determining the degree of alignment of the prosthesis to the performance...
-
Powikłania po rekonstrukcji piersi: problem zakażeń i strategii prewencyjnej - przegląd literaturowy
PublicationW niniejszej pracy przedstawiono dane dotyczące powikłań po rekonstrukcji piersi. Manuskrypt ma na celu usystematyzowanie wyników badań z ostatnich lat wraz z aspektami, takimi jak: częstotliwość występowania powikłań oraz ich rodzaj, czynniki predysponujące, a także możliwości profilaktyki. Przeanalizowano dane literaturowe z ogólnie dostępnych artykułów z okresu ostatnich pięciu lat, ze szczególnym uwzględnieniem zakażeń. Do...
-
The Effect of Long Term Service at Elevated Temperatures on Microstructure Degradation of Austenitic Reformer Tubes
PublicationThe paper analyses the relationship between an increase of the inner diameter of tubes made of Manaurite XM cast steel and transformations occurring in their microstructure due to long-lasting operation in methane reformer. Examinations included metallographic analysis with light microscope (LM), scanning electron microscope (SEM) and microanalysis of the chemical composition of precipitates (EDX). It was indicated that there is...
-
Influence of parameters of deep grinding on nanohardness and surface roughness of C45 steel
PublicationPrzedstawiono wyniki badań wpływu głębokości współbieżnego szlifowania powierzchni płaskich na chropowatość i nanotwardość warstwy wierzchniej stali C45 o strukturze ferrytyczno-perlitycznej i średniej wielkości ziarna 20 μm. Dla wszystkich wartości głębokości szlifowania uzyskano znaczny wzrost twardości warstwy wierzchniej przedmiotu obrabianego.
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Effect of the Post-Weld Surface Condition on the Corrosion Resistance of Austenitic Stainless Steel AISI 304
PublicationSurfaces of welded elements made of corrosion-resistant (stainless) steels develop temper colours. The removal of thickened oxide layers off steels exposed to temperatures below 300°C is necessary and entails the restoring of high corrosion resistance of the stainless steel. The article presents tests concerned with the effect of a method applied to remove post-weld temper on the corrosion resistance of austenitic stainless steel...
-
Badania spawalności stali S460N w środowisku wodnym z wykorzystaniem próby Tekken
PublicationSpawanie w środowisku wodnym niesie ze sobą wiele problemów, wśród których najważniejszym jest skłonność stali do powstawania pęknięć zimnych. O ile w przypadku spawania na powietrzu istnieje wiele metod zapobiegania tym pęknięciom, o tyle pod wodą zastosowanie tych metod jest ograniczone. Z tego powodu konieczne jest określenie skłonności danego materiału do pękania zimnego. W pracy oceniono spawalność drobnoziarnistej...
-
Influence of dopants on structure of polycrystalline bismuth niobate
PublicationBismuth niobate (BiNbO4) has attracted attention as a low-fired ceramics with promising microwave application potential. BiNbO4 ceramics was fabricated by mixed oxide method and sintered at temperature T<1000˚C. As the sintering aids a small amount of CuO oxide was used. The crystalline structure of the ceramic samples was examined by X-ray diffraction method at room temperature. The Rietveld refinement method was used for analysis...
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Determination of moisture resistance of covered electrodes according to PN-EN ISO 14372
PublicationMoisture present in the electrode covering is one of the sources of diffusible hydrogen in welded joints. In order to study the diffusible hydrogen content in deposited metal, a stand for moisturizing covered electrodes, in accordance with the PN-EN ISO 14372 standard, was built. After the stand was completed, a test of moisturizing the electrodes was carried out and measurements of the diffusible hydrogen content in deposited...
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublicationGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
Quality increase for single-welded joints of thin-walled structures by means of simulation modelling
PublicationThe Simulation calculation module and the SolidWorks software package have helped to define the optimal shape and dimensions of single-welded joints which may serve the basis for calculating the process parameters of welding. Having compared the models with different weld cross-sections the authors have defined that the weld height and width do not significantly affect the stress concentration, and the stress concentration and...
-
INFLUENCE OF CERAMIC COATING ON MECHANICAL PROPERTIES OF STAINLESS STEEL
PublicationCrystal structure and phase composition of stainless steel substrates (AISI 304 type) was studied and it was found that they adopted the cubic symmetry. The calculated elementary cell parameter for the mayor Fe-Ni phase (weight fraction 99%) was a = 3.593 Å, whereas the mean grain size was = 2932 Å. Morphology of the stainless steel substrate surface was studied with profilometry. Mechanical properties of the stainless steel...
-
X-RAY DIFFRACTION STUDY OF BISMUTH LAYER-STRUCTURED MULTIFERROIC CERAMICS
PublicationGoal of the present research was to apply a solid state reaction route to fabricate bismuth layer-structured multiferroic ceramics described with the formula Bi5FeTi3O15 and reveal the influence of processing conditions on its crystal structure and phase composition. Simple oxide powders Bi2O3, TiO2 and Fe2O3 were used to fabricate Aurivillius-type bismuth layer-structured ferroelectrics. Pressureless sintering in ambient air was...
-
Modelowanie asymetrycznego procesu walcowania blach bimetalowych = The modeling of asymetrical rolling process of bimetallic plate
PublicationW pracy rozważano problem płynięcia plastycznego bimetalowego pasma podczas asymetrycznego procesu walcowania blach bimetalowych. Asymetrię procesu uzyskano w wyniku wprowadzenia różnic w wartościach sił tarcia na powierzchniach styku pasma z poszczególnymi walcami.
-
Numerical modelling of asymetric double-layer Al-Cu plate rolling process
PublicationNiekorzystnym zjawiskiem towarzyszącym procesom walcowania płaskich wyrobów bimetalowych jest krzywizna pasma na wyjściu z kotliny walcowniczej wynikająca z nierównomierności odkształcenia warstw bimetalowej blachy. Możliwość szybkiego i łatwego przeciwdziałania temu zjawisku daje wprowadzenie asymetrii prędkości bądź średnic walców roboczych. W przedstawionym artykule zaprezentowano badania komputerowe procesu walcowania blach...
-
Wpływ parametrów asymetrycznego walcowania na krzywiznę walcowanej blachy bimetalowej = The influence of parameters of assymetric rolling on the curvature of bimmetal plate
PublicationWyginanie się bimetalowych blach grubych po wyjściu z kotliny walcowniczej jest zjawiskiem utrudniającym bezawaryjne prowadzenie procesu technologicznego. Na podstawie licznych prac [1¸4] można stwierdzić, że zastosowanie walcowania asymetrycznego jest jedną z metod pozwalających na wyeliminowanie niekorzystnego wpływu wyginania się dwuwarstwowej blachy po procesie walcowania. Do badań numerycznych asymetrycznego procesu walcowania...
-
Numeryczne modelowanie prędkości płynięcia warstw blachy bimetalowej w procesie walcowania = The numerical modelling of the layers flow velocity in bimetal plates rolling proces
PublicationW pracy przedstawiono wyniki obliczeń numerycznych dotyczących procesu asymetrycznego walcowania blach bimetalowych 18G2A+1H13.
-
The reactions occuring on the implant as a result of contact with human tissue
PublicationObecnosc implantu w ciele czlowieka powoduje liczne, czesto nieprzewidywalne skutki. Powodem takiej sytuacji jest duza roznorodnosc interakcji materialu medycznego z kontaktujaca sie z nim tkanka. Stwierdzenie to dotyczy glownie oddzialywan i skutkow zachodzacych na poziomie molekularnym w poszczegolnych komorkach kontaktujacej sie tkanki.
-
Allergy to implant components: chromium, nickiel, cobalt and titanium
PublicationImplant jest kompozycja roznych pierwiastkow: niklu, chromu, kobaltu, tytanu, molibdenu i wanadu. Pierwiastki te moga doprowadzic do alergii, egzemy i obluzowania implantu.
-
CLAY MINERALS – MINERALOGY AND PHENOMENON OF CLAY SWELLING IN OIL & GAS INDUSTRY
PublicationAmong the minerals found in the earth's crust, clay minerals are of the widest interest. Due to the specific properties such as plasticity, absorbing and catalytic properties clay minerals are used in many industries (oil & gas, chemistry, pharmacy, refractory technology, ceramics etc.). In drilling, a phenomenon of swelling clays is frequently observed. It has an important impact on the cementing quality. During the last few decades...
-
Reduction of Derivative pipeline effort in water turbine
PublicationThe paper presents an approach to evaluate and reduce the effort of the derivative pipeline in a water turbine of a hydrostatic power station in its vulnerable spots. Potential places of the biggest effort of the structure, as well as the coefficient of displacement and safety factor related to them were identified using FEM numerical method. Pipeline reinforcement was designed and made based on FEM analysis. Original technology...
-
Opinia dotycząca stanu mieszadeł komór fermentacyjnych oczyszczalni ścieków Gdańsk-Wschod
PublicationDokonano oględzin i oceny stanu mieszadła zbiornika 15/3.
-
Influence of Spatial Structures of 316L Stainless Steel on Its Cavitation Erosion Resistance
PublicationCavitation erosion performance of modified macroscopic internal structure 316L stainless steel was investigated. The samples processed by means of SLM method were subjected to cavitation erosion test. The scanning electron microscope Philips 30/ESEM was used to examine morphology of eroded surface.
-
Ocena przyczyn awarii robota BT-1000
PublicationPrzeprowadzono analizy kinematyki ruchu elementów głowicy robota oraz obliczenia symulacyjne stanu obciążeń połączeń ruchowych w celu oceny rzeczywistego stanu pracy tych elementów. Oceniono modyfikacje konstrukcyjne i sformułowano wnioski odnośnie możliwości zwiększenia trwałości najbardziej obciążonych elementów.
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublicationThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Ekspertyza materiałowa rurociągu wody pitnej ze stali gatunku AISI 304
PublicationCelem pracy było ustalenie przyczyny zniszczenia instalacji wodociągowej w budynku. Instalacja była wykonana ze stali nierdzewnej AISI 304. Zakres pracy obejmował: badania makroskopowe uszkodzeń, mikroanalizę EDX produktów korozji występujących na powierzchni wewnętrznej rurociągu, badania metalograficzne uszkodzeń i ocena stanu stali. Analiza doboru stali na elementy instalacji wodociągowej
-
Ocena stanu technicznego i prognoza trwałości eksploatacyjnej reaktorów 150-R1 i 150-R2 na instalacji 150 w Grupie Lotos SA w postoju 2013
PublicationPrzedmiotem pracy było wykonanie oceny stanu technicznego reaktorów 150-R1 i 150-R2 instalacji 0150 po remoncie w 2013
-
Outboard valve material testing
PublicationWykonano analizę przyczyn uszkodzenia korozyjnego zaworu zaburtowego. Sformułowano wnioski.
-
Raport z badań materiałowych rurociągu instalacji wody chłodzącej hydrozespołu HZ-4 z Elektrowni Wodnej Żarnowiec
PublicationWykonano badania materiałowe fragmentów rurociągów instalacji wody chłodzącej hydrozespołu. Zakres pracy obejmował analizę chemiczną stali rurociągu, badania makroskopowych uszkodzeń rurociągu, badania EDX osadów i produktów korozji występujących na powierzchni wewnętrznej rurociągu, badania mikroskopowe uszkodzeń i oceny stanu rurociągu
-
Effect of microstructure on mechanical properties and corrosion resistance of 2205 duplex stainless steel
PublicationThis paper presents results of the research on impact of microstructure of austenitic-ferritic steel of duplex type on its mechanical properties and susceptibility to stress corrosion cracking. As showed, improper processing technologies more and more often used in shipbuilding industry for plates and other half-finished products made of duplex steel may cause significant lowering their properties, which frequently makes their...
-
Progress in the post weld residual stress evaluation using Barkhausen effect meter with a novel rotating magnetic field probe
PublicationWe report the progress in post weld residual stress evaluation using Barkhausen effect (BE) meter with rotating magnetic field probe. The novel probe of the BE meter contains two C-core electromagnets and searching coil with ferrite antenna. This meter allows automatic measurements of BE intensity envelopes at different angles of magnetizing field. The full process of measurement at given position of the probe takes about only...
-
Wpływ budowy złożonych warstw powierzchniowych i nano-warstw na trwałość kompozytów poliestrowo-szklanych w środowisku wodnym
PublicationModyfikacja nanocząstkami warstw laminatów stosowanych na małe jednostki pływające powinno spowodować korzystne zmiany morfologii mikrostruktury, podwyższyć odporność udarową i zwiększyć odporność na działanie wody. Celem naukowym pracy, dotyczącej degradacji kompozytów polimerowych stosowanych w budowie małych jednostek pływających, była charakterystyka porównawcza materiałów warstwowych aktualnie proponowanych przez przemysł...
-
Pomiar naprężeń własnych metodą Barkhausena za pomocą sondy z wirującym polem magnetycznym
PublicationW pracy przedstawiono nowy sposób pomiaru naprężeń własnych w elementach konstrukcji z wykorzystaniem polowego efektu Barkhausena. Informację o stanie naprężeń uzyskano z analizy rozkładu kątowego natężenia efektu Barkhausena zmierzonego w sposób automatyczny poprzez sondę z wirującym polem magnetycznym. Przedstawiono zasadę działania i opis układu pomiarowego oraz przykłady wykorzystania tej metody w ocenie stanu naprężenia w...
-
Opony i nawierzchnie drogowe dla samochodów elektrycznych
PublicationOd czasu wynalezienia koła, które to wydarzenie miało miejsce około 6 tys. lat temu, rozpoczęła się era transportu kołowego trwająca do dzisiaj. W początkowym okresie koło, a często walec, wykorzystywane były jedynie do przesuwania ciężkich przedmiotów na niewielkie odległości. Potem pojawiły się pojazdy kołowe napędzane siłą mięśni zwierząt pociągowych. Dopiero pod koniec XVIII wieku zbudowano pierwsze pojazdy, które możemy zakwalifikować...
-
Analiza skupień jako metoda wspomagania decyzji zakupu urządzeń prądu stałego do spawania metodą TIG
PublicationW pracy podjęto zagadnienie wspomagania decyzji zakupu odpowiedniego spawalniczego źródła prądu. Zaproponowano rozwiązanie problemu z wykorzystaniem metod analizy skupień. Przedstawiono wyniki klasyfikacji 69 urządzeń prądu stałego do spawania TIG metodami Warda i k-średnich dla odpowiednio dobranego i przygotowanego zestawu cech diagnostycznych. Na podstawie wyników uznano, że analiza skupień może być skuteczną metodą wspomagania...
-
Wpływ warunków przechowywania na jakość drutów proszkowych
PublicationW pracy przedstawiono wyniki badań chłonności drutów proszkowych. Badane druty proszkowe zostały poddane ekstremalnym warunkom 60°C i wilgotności względnej 90% przez 240 godzin. Określono chłonność oraz zbadano jakość powierzchni drutów proszkowych po ekspozycji. Wykonano napoiny nawilżonymi drutami proszkowymi i zbadano ilość wodoru dyfundującego w stopiwie.
-
OPRACOWANIE TECHNOLOGII OTRZYMYWANIA MEMBRAN CHITOZANOWYCH DO ZABIEGU STEROWANEJ REGENERACJI KOŚCI
PublicationPoniżej przedstawione badanie miało na celu wytworzenie asymetrycznych membran chitozanowych do zabiegu sterowanej regeneracji kości w stomatologii. W celu zbadania uzyskanej struktury wykonano mikrofotografie SEM.
-
Use of X-ray radiography in the diagnosis of bonded anchors
PublicationKotwy wklejane należą do najbardziej popularnych metod montażu elementów konstrukcyjnych. Promieniowanie rentgenowskie częściowo umożliwia diagnostykę zespolenia lepiszcza z podłożem. W pracy przedstawiono wyniki analizy wpływu parametrów technicznych aparatów rentgenowskich na sposób i dokładność wykonania zdjęć diagnostycznych osadzenia kotew stalowych przy zastosowaniu lepiszcza syntetycznego
-
The bahaviour of selected silver coated body implants in presence of various bacteria
PublicationThe article deals with implants covered with silver nanoparticles and its influence on bacteria adhesion.
-
IMPULSE NOISE ASSOCIATED WITH FIRING HANDHELD MILITARY WEAPONS
PublicationSports, hunting and military shooting grounds are well known sources of noise that can be disruptive both for people present at those facilities, as well as for people and animals that live nearby. What is more, shooters are also subjected to very painful and dangerous impulse noise. The paper discusses the issues related to the noise immission during firing of small firearms of military type that are typical for Poland. The experiments...
-
Noise Generated by Tyres Designet for Electric Vehicles - Results of Laboratory Experiments
PublicationA few years ago, electric and hybrid vehicles were rarely seen on public roads and were considered more as exotic curiosities or even as a sign of extravagance than a practical means of transport. Nowadays the situation has changes significantly. This was caused both by the technical development and legislative actions, as well as the organizational nature promoting the purchace and use of low emission vehicles. Electric vehicles...