Search
Filters
total: 15
filtered: 12
-
Catalog
Chosen catalog filters
Search results for: PROFILOMETRIA
-
Medical polyurethanes with different hard segments content obtained from polycaprolactone diol, aliphatic diisocyanates and butanediol.
PublicationW artykule opisano syntezę 3 serii segmentowych poliuretanów o przeznaczeniu medycznym otrzymanych z polikaprolaktonodiolu, alifatycznych diizocyjanianów: 1,6 heksametylenowego lub 4,4'-dicyklohesametylenowego oraz butanodiolu. Przedstawiono charakterystykę PU uzyskaną na podstawie badania pęcznienia w wodzie, oleju oraz soli fizjologicznej, właściwości powierzchniowych (kąt zwilżania i profilometria), a także badania IR i DSC....
-
Spectroscopic studies of sol-gel derived thin film structures for integrated optics
PublicationPrzedstawiono wyniki badania struktur cienkowarstwowych wykonywanych dla zastosowań w optyce zintegrowanej z polimerów hybrydowych (np. w postaci ścieżek śwaitłowodów planarnych). Jakość i jednorodność stuktur badano za pomocą mikroskopii ramanowskiej, mikroskopii optycznej i profilometrii światła białego. Wykonano porównanie wyników uzyskanych tymi trzema metodami.
-
Fracture Energy of Bonded Joints with 2D Elastic Adhesive Layer
PublicationWhen bonded joint is subjected to mode I fracture loading, the adhesive joints analytical solutions treats the adhesive layer, usually, as not existing or 1D Hooke elastic layer. In the case of 1D elastic layer, represented as Hookes spring element, is acting, only, in direction contrary to the applied load. Basing on the information yielded from sensitive laser profilometry technique, where deflections of bonded part of the joint...
-
Dimensional accuracy and roughness of lamellas when sawing frozen wood
PublicationPrzedstawiono wpływ obniżania temperatury drewna sosnowego (-5°C i -20°C) i prędkości posuwu na dokładność wymiarową deszczułek oraz chropowatość powierzchni po przecinaniu. Badania prowadzono na pilarce ramowej wielopiłowej PRW15M z użyciem cienkich pił z ostrzami stellitowanymi. Otrzymywane wyniki odnoszono do wyników przecinania drewna o temperaturze +18°C. Profil grubości określano metodą kontaktową z pomiarem ciągłym na długości...
-
Adhesive compliance effect in mode I separation:Profilometry approach
PublicationThe effect of adhesive compliance on the deflection of a loaded, bonded beam was studied using laser profilometry. Experimental data obtained were compared with both Euler-Bernoulli (encastré) and Winkler (one parameter elastic foundation) models. A third, analytical, 2D model, based on shear within the adhesive layer (two parameter elastic foundation), was introduced. Finite element analysis (FEA) was also used to study the effect...
-
Formation and Growth of the Crack in Bonded Joints Under Mode I Fracture: Substrate Deflection at Crack Vicinity
PublicationAdhesive bonding is now commonly used in aircraft, cars, boats, etc. In these applications, thin panels are often bonded. In such thin structures, heterogeneous mechanical loading along the bondline edge (or potential crack front), is likely to arise due to 3D structural effects. The crack front and its vicinity is a special region, in that it is where structural properties of the adherend material meet those of the adhesive (discontinuity)....
-
Laser reflectance interferometry system with a 405 nm laser diode for in-situ measurement of CVD diamond thickness
PublicationIn situ monitoring of the thickness of thin diamond films during technological processes is important because it allows better control of deposition time and deeper understanding of deposition kinetics. One of the widely used techniques is laser reflectance interferometry (LRI) which enables non-contact measurement during CVD deposition. The authors have built a novel LRI system with a 405 nm laser diode which achieves better...
-
On the crack front curvature in bonded joints
PublicationStandard tests of adhesively bonded specimens are likely to produce heterogeneous stress distribution along the crack front and its vicinity. High separation rate mode I dominated fracture test is performed.Observation of post mortem fractured surfaces with an optical microscope reveals characteristic features of mixed mode I/III fracture near the sides of the specimen but not in the middle. At first, finite elements calculations...
-
Badania tribologicznych właściwości nanokompozytowych warstw Ni-P/Si3N4 osadzanych metodą redukcji chemicznej na stopie aluminium AW-7075
PublicationPrzedstawiono wyniki tribologicznych badań warstw nanokompozytowych Ni-P/Si3N4 i niklowych Ni-P osadzonych na stopie aluminium AW-7075 metodą redukcji chemicznej, a także stopu AW-7075 bez powłoki. Warstwy nanokompozytowe wytworzono, stosując azotek krzemu Si3N4 w postaci polidyspersyjnego proszku o wielkości cząstek 20–25 nm. Analizowano wpływ zawartości w materiale warstwy fazy dyspersyjnej na twardość i zużycie ścierne, którą...
-
INFLUENCE OF CERAMIC COATING ON MECHANICAL PROPERTIES OF STAINLESS STEEL
PublicationCrystal structure and phase composition of stainless steel substrates (AISI 304 type) was studied and it was found that they adopted the cubic symmetry. The calculated elementary cell parameter for the mayor Fe-Ni phase (weight fraction 99%) was a = 3.593 Å, whereas the mean grain size was = 2932 Å. Morphology of the stainless steel substrate surface was studied with profilometry. Mechanical properties of the stainless steel...
-
Optical profilometer
PublicationThe profilometry plays a huge role in the most fields of science and technology. It allows to measure the profile of the surface with high-resolution. This technique is used in the fields like optic, electronic, medicine, automotive, and much more. The aim of the current work was to design and build optical profilometer based on the interference phenomena. The developed device has been working with He-Ne laser (632.8 nm). The optical...
-
Diamond-based protective layer for optical biosensors
PublicationOptical biosensors have become a powerful alternative to the conventional ways of measurement owing to their great properties, such as high sensitivity, high dynamic range, cost effectiveness and small size. Choice of an optical biosensor's materials is an important factor and impacts the quality of the obtained spectra. Examined biological objects are placed on a cover layer which may react with samples in a chemical, biological...