Filtry
wszystkich: 1074
wybranych: 903
Wyniki wyszukiwania dla: HEAT TRANSFER SURFACE AREA
-
Comparative study of a bottoming SRC and ORC for Joule–Brayton cycle cooling modular HTR exergy losses, fluid-flow machinery main dimensions, and partial loads
PublikacjaEnergy conversion efficiency increase in power plants with high-temperature gas-cooled reactors via implementation of the bottoming cycle was investigated under nominal and minimal thermal load of a high-temperature reactor (HTR). Heat transfer surface area and turbine outlet volumetric flow rate in bottoming cycles was also investigated. Water and two low-boiling point working fluids (ammonia and ethanol) were analyzed. Analyzed...
-
Heat Transfer in Adsorption Chillers with Fluidized Beds of Silica Gel, Zeolite, and Carbon Nanotubes
Publikacja -
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublikacjaIn the paper are presented the results of calculations using authors own model to predict heat transfer coefficient during flow boiling for carbon dioxide. The experimental data from various researches were scrutinised conducted for a full range of quality variation and wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The work shows the importance of taking into account surface...
-
Heat Transfer During Pool Boiling of Water, Methanol and R141b on Porous Coated Horizontal Tube Bundles
PublikacjaThis paper presents the results of experimental investigation of water, methanol and R141b refrigerant boiling on horizontal porous coated tube bundles supposed to represent a flooded-type evaporator. Experiments were carried out for a bundle of 19 tubes in triangular layout for two pitch-to-diameter ratio values – 1.7 and 2.0 – in atmospheric and sub-atmospheric pressure conditions. Average heat transfer coefficients – both local,...
-
Heat transfer and fluid flow visualization using liquid crystal thermography
PublikacjaW pracy przedstawiono możliwości wykrzystania termografii ciekłokrystalicznej do badań wymiany ciepła oraz wizualizacji pola przepływu w elementach urządzeń przemysłowych.
-
The Numerical Comparison of Heat Transfer in a Coated and Fixed Bed of an Adsorption Chiller
Publikacja -
A comparative study of different methods for heat transfer enhanced by the use of TVG
PublikacjaArtykuł dotyczy badań eksperymentalnych i numerycznych intensyfikacji wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu dla różnej geometrii turbulizatorów. Do badań eksperymentalnych wykorzystano termografię ciekłokrystaliczną a modelowanie fizyczne wykonano za pomocą kodu komputerowego FLUENT.
-
Numerical single-phase modeling of turbulent flow and heat transfer of nanofluids
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (6 000< Re < 12 000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with published experimental data.
-
Hybrid evolutionary partitioning algorithm for heat transfer enhancement in VLSI circuits
PublikacjaW niniejszym artykule przedstawiono metodę pozwalającą na polepszenie transferu ciepła z układu scalonego do otoczenia poprzez zwiększenie liczby połączeń zewnętrznych, co pozwoliło na polepszenie przewodności cieplnej układu scalonego. Dla osiągnięcia tego celu opracowano nowy, hybrydowy, ewolucyjny algorytm podziału (ang. Hybrid Evolutionary Partitioning Algorithm - HEPA). Obliczenia przeprowadzone dla wybranych przykładów testowych...
-
Turbulent flow and heat transfer of a liquid film formed by impinging jet.
PublikacjaZaproponowano prosty model wymiany ciepła w turbulentnym filmie cieczowym utworzonym przez uderzająca strugę. Rozpatrzono dwa przypadki: przepływ rozwijający się i w pełni rozwinięty filmu cieczowego. W obu przypadkach model wyprowadzono na podstawie zmiany grubości filmu w wyniku działania sił bezwładności i sił tarcia. Wyznaczono profile prędkości w obu zakresach co umożliwia wyznaczenie współczynników wymiany ciepła.
-
Experimental study of natural convection heat transfer from horizontal conic
PublikacjaPrzedstawiono badania eksperymentalne i ich wyniki konwekcji swobodnej w wodzie i powietrzu poziomych stożków o kącie przy podstawie 30, 45 i 60 deg. Wyniki badań wykazują dobrą zgodność z rozwiązaniem teoretycznym i z danymi literaturowymi.
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublikacjaIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Inverse heat transfer problem solution of sounding rocket using moving window optimization
PublikacjaAn Inverse Heat Transfer Problem is solved for a sounding rocket module given its geometry and measured temperature profile. The solution is obtained via moving window optimization, a technique for solving inverse dynamics. An analysis is performed to modify the method to avoid oscillatory behavior of the resulting heat flux profile. The method parameters are tuned in relation to characteristic phases of the flight. Results are...
-
Structural optimization of microjet array cooling system
PublikacjaThe single phase heat transfer from an upward facing, horizontal copper surface to arrays of impinging water jets was experimentally investigated. Experimental configuration allows for a free-surface unconfined jets flow. Square nozzles 50 × 100 μm arranged in four different geometries were used. Additionally, for the set of two jets array geometry was varied by adjusting the nozzle to nozzle distance. The area averaged heat transfer...
-
Impact of the inclination angle of the condenser with refrigerant R410A on heat transfer coefficient – experimental study
PublikacjaIn the paper the authors present results of a laboratory test of the condenser with refrigerant R410A. The effect of the inclination of this condenser on the heat transfer coefficient value has been considered. The test has proved that there is an optimal inclination angle of the condenser which gives maximal value of this coefficient.
-
Theoretical consideration of free convective heat transfer from a round isothermal plate slightly inclined from the vertical
PublikacjaA semi-analytical solution of simplified Navier-Stokes and Fourier-Kirchhoff equations describing free convective heat transfer from a round isothermal surface slightly inclined from the vertical is presented. The solution is based on the assumption, typical for natural convection, that the velocity component normal to the surface is negligibly small in comparison to the tangential one. Next we neglect the nonlinear inertia force...
-
Numerical model for thin liquid film with evaporation and condensation on solid surfaces in systems with conjugated heat transfer
PublikacjaCondensation and evaporation processes from wetted surfaces are of utmost importance in many technological or industrial applications. In many devices such as home-appliances and air conditioning systems just to name a few, condensation and evaporation processes greatly impact their performance and energy efficiency; The physics of these processes is quite complex, involving conjugate heat transfer among solid–liquid film-gaseous...
-
Implementation of the Boundary Element Method to Two-Dimensional Heat Transfer with Thermal Bridge Effects
PublikacjaThe work presents an application of the boundary element method applied to a two-dimensional conductive heat transfer. The algorithm of the method is explained and its advantages are outlined. Green's function as a fundamental solution for Poisson's equation in two dimensions was used and the direct approach was applied. The presented results concern building construction elements as typical cases of thermal bridges. Some properties...
-
Experimental study of flow boiling pressure drop and heat transfer of R1233zd(E) at moderate and high saturation temperatures
PublikacjaThe paper presents the results of experimental study of flow boiling of R1233zd(E) in minichannel at moderate and high saturation temperatures. The heat transfer coefficient and pressure drop were measured for flow boiling in a stainless steel tube with 2 mm inside diameter and a length of 300 mm. Experiment has been conducted for saturation temperatures ranging from 83 to 145 °C which corresponds to values of reduced pressures...
-
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublikacjaW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaNanofluids came to be seen as a new generation of coolants, especially in single-phase systems. Conducted experiments indicate that the increase in thermal conductivity is not the only reason for the intensification of heat transfer when using nanofluids. Preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter...
-
EXPERIMENTAL VERIFICATION OF THE METHOD OF FLOW BOILING AND FLOW CONDENSATION HEAT TRANSFER PREDICTION FOR SELECTED FLUIDS
PublikacjaIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of different refrigerants. The experimental data from various research studies from literature were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in- house developed model....
-
Experimental Investigation of an Intensified Heat Transfer Adsorption Bed (IHTAB) Reactor Prototype
Publikacja -
Experimental study of flow pattern and heat transfer during steam drying of wood
PublikacjaBadania wysokotemperaturowego suszenia drewna zostały zainspirowane koniecznością instensyfikacji wymiany ciepła i masy na potrzeby przemysłu drzewnego, a w szczególności meblarskiego, w zakresie doskonalenia metod suszenia drewna, modelowania intensyfikacji wymiany ciepła i masy w elementach suszonych, opracowania ekologicznych i energooszczędnych systemów suszarniczych, ochrony środowiska związanej z racjonalnym zużyciem energii,...
-
Prediction of flow boiling heat transfer data for R134a, R600a and R290 in minichannels
PublikacjaIn the paper presented is the analysis of the results of calculations using a model to predict flow boiling of refrigerants such as R134a, R600a and R290. The latter two fluids were not used in development of model semiempirical correction. For that reason the model was verified with present experimental data. The experimental research was conducted for a full range of quality variation and a relatively wide range of mass velocity....
-
Flow visualization and heat transfer investigations on the flat plate with streamwise pressure gradient
PublikacjaPaper presents experimental investigations results for film cooling on a flat plate. The main objective of the design is the streamwise pressure distribution on the flat plate as in the blade cascade. The transient and steady-state technique with liquid crystals for the surface temperature distribution with film cooling has been used in experiments in a low speed wind tunnel.
-
Heat transfer enhancement, flow visualization and friction characteristics in rib-roughened channels
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych związanych z intensyfikacją wymiany ciepła w kanałach wyposażonych w żebra, które poprawiają warunki przejmowania ciepła od ścianki do przepływającego medium. W badaniach wykorzystano system PIV oraz termografię ciekłokrystaliczną.
-
The effect of plate size on the natural convective heat transfer intensity of horizontal surfaces
PublikacjaW pracy przedstawiono badania wpływu rozmiarów płyty prostokątnej poziomej na intensywność wymiany ciepła w warunkach konwekcji swobodnej. Zaproponowano dwa zakresy: dla płyt o wymiarze charakterystycznym mniejszym niż 0,1 m - 0,2 m intensywność konwekcyjnej wymiany ciepła jest odwrotnie proporcjonalna do szerokości płyty, dla płyt szerszych niż 0,2 m szerokość płyty nie wpływa znacząco na współczynnik konwekcyjnej wymiany ciepła....
-
Influence of porous coating on heat transfer during R22 and R134a flow boiling.
PublikacjaPrzedstawiono wpływ powłoki porowatej na przenoszenie ciepła i spadku ciśnienia podczas wrzenia w przepływie czynników chłodniczych, R22 i R134a.
-
Theoretical and experimental research of heat and mass transfer in adsorption process in dac systems
PublikacjaPrzedstawiono badania wymiany ciepła i masy w stałych adsorpcyjnych elementach wykonanych na bazie silikażelu. Zaprezentowano również informacje dotyczące osuszania w systemach klimatyzacyjnych. Na zkończenie pokazano wyniki numerycznej symulacji i skojarzonej wymiany ciepła i masy w chłodzonym osuszaczu.
-
Influence of pressure on heat transfer during pool boiling on smooth tube bundle
PublikacjaPrzedstawiono wyniki badań eksperymentalnych wrzenia wody, metanolu i R141b na pęu rur głądkich w warunkach podcisnienia i ciśnienia atmosferycznego
-
Turbulence model evaluation for numerical modelling of turbulent flow and heat transfer of nanofluids
PublikacjaIn this work, Nusselt number and friction factor are calculated numerically for turbulent pipe flow (Reynolds number between 6000 and 12000) with constant heat flux boundary condition using nanofluids. The nanofluid is modelled with the single-phase approach and the simulation results are compared with experimental data. Ethylene glycol and water, 60:40 EG/W mass ratio, as base fluid and SiO2 nanoparticles are used as nanofluid...
-
Influence of nanoparticle concentration on convective heat transfer of water-Al2O3 nanofluids inside horizontal tubes
PublikacjaThis work presents preliminary results of the experimental investigation of the forced convection heat transfer of water-Al2O3 nanofluids inside stainless steel tube with 8 mm internal diameter and 2000 mm length. Nanoparticles were tested at the concentrations of 0.01%, 0.1%, 1% and 5% by weight and the Reynolds number range encompasses laminar as well as turbulent flows.
-
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...
-
Promising Nanoparticle-Based Heat Transfer Fluids—Environmental and Techno-Economic Analysis Compared to Conventional Fluids
PublikacjaProviding optimal operating conditions is one of the major challenges for effective heating or cooling systems. Moreover, proper adjustment of the heat transfer fluid is also important from the viewpoint of the correct operation, maintenance, and cost efficiency of these systems. Therefore, in this paper, a detailed review of recent work on the subject of conventional and novel heat transfer fluid applications is presented. Particular...
-
A new construction of shell-and-tube heat exchanger with impinging jets and minichannels technologies for heat recovery from gases – experimental analysis
PublikacjaA dynamic development of technologies allowing waste heat utilization is observed in a correspondence with a pro-ecological approach of the zero waste idea. Such approach becomes the most demanding in the area of low-temperature was heat sources, especially gaseous media. Till now, they were usually not utilized due to unfavorable thermal conditions and high costs. Therefore, the zero waste approach directs research on techniques...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublikacjaThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
Computational analysis of power-law fluids for convective heat transfer in permeable enclosures using Darcy effects
PublikacjaNatural convection is a complex environmental phenomenon that typically occurs in engineering settings in porous structures. Shear thinning or shear thickening fuids are characteristics of power-law fuids, which are non-Newtonian in nature and fnd wide-ranging uses in various industrial processes. Non-Newtonian fuid fow in porous media is a difcult problem with important consequences for energy systems and heat transfer. In this...
-
Analytical model with non-adiabatic effects for pressure drop and heat transfer during boiling and condensation flows in conventional channels and minichannels
PublikacjaIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for boiling flow and condensation flow with account of non- adiabatic effects for some recent data collected from literature. The first effect, the modification of interface shear stresses in annular flow pattern is considered through incorporation of the so called "blowing parameter". The mechanism of...
-
Heat Transfer Augmentation through Different Jet Impingement Techniques: A State-of-the-Art Review
Publikacja -
Intensyfikacja wymiany ciepła przy pomocy mikrostrug = Heat transfer intensification using microjets.
PublikacjaW pracy przedstawiono wyniki badań eksperymentalnych nad intensyfikacją strumienia ciepła przy pomocy pojedynczej mikrostrugi wody. W pracy przedstawiono wyniki badań dla dysz o średnicy 180 i 280 mikrometrów.
-
Nucleate pool boiling heat transfer from small horizontal smooth tube bundles
PublikacjaPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia wody destylowanej, metanolu i R141b na poziomym pęku rur gładkich, który składał się z 19 rurek, ogrzewanych elektrycznie, w układzie przestawionym i podziałce 1.7d oraz 2.0d. Wyznaczono również wartości współczynnika wpływu pęku. Podano równanie korelacyjne do obliczania średniego współczynnika przejmowania ciepła
-
Numerical Investigation of Nuclear Reactor Kinetic and Heat Transfer Fractional Model with Temperature Feedback
PublikacjaAbstract—In the paper, the numerical results concerning the kinetics and proposed heat exchange models in nuclear reactor based on fractional calculus are presented for typical inputs. Two fractional models are proposed and compared with the model based on ordinary derivative. The first fractional model is based on one of the generalized Cattaneo equations. The second one is based on replacing the ordinary to fractional order of...
-
Determination of heat transfer coefficient in evaporator of the organic Rankine cycle using the Wilson method.
PublikacjaW pracy zastosowano metodę Wilsona do wyznaczania współczynnika przejmowania ciepła. Przedmiotem rozważań jest płytowy wymiennik ciepła pracujący jako parownik w laboratoryjnym stanowisku realizującym obieg ORC. Wykorzystana metoda jest metodą wydajną w przypadku wymienników ciepła o złożonej geometrii i dużej liczbie kanałów, dla których pomiar temperatury ścianki jest niemożliwy, a przez to określenie współczynników przejmowania...
-
Free convective heat transfer structures as a function of the width of isothermal horizontal rectangular plates
PublikacjaZaprezentowano rezultaty badań eksperymentalnych konwekcyjnej wymiany ciepła od izotermicznych płyt prostokątnych skierowanych ku górze. Na podstawie przeprowadzonych wizualizacji zaproponowano dwa modele struktur przepływu. Rozwiązania analityczne dla tych modeli przedstawiono w postaci zależności liczb Nusselta Rayleigh'a. Stwierdzono, że przepływ koncentryczny występuje dla małych wartości liczb Ra, szczególnie w przypadku płyt...
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublikacjaPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
Natural convective heat transfer from isothermal horizontal, vertical and inclined plates - a review
PublikacjaW artykule przedstawiono przegląd otrzymanych przez różnych badaczy korelacji eksperymentalych, teoretycznych i numerycznych, opisujących wymianę ciepła od izotermicznych płyt o różnym kącie pochylenia. Przedstawiono model matematyczny zjawiska. Opisano stosowane metody badawcze i wskazano przyczyny rozbieżności pomiędzy przedstawionymi przez wielu autorów wynikami.
-
The use of liquid crystal thermography and particle image velocimetry in the exploration of heat transfer measurements
PublikacjaArtykuł dotyczy badań eksperymentalnych wymiany ciepła w modelowym wymienniku ciepła z turbulizatorami przepływu przy użyciu termografii ciekłokrystalicznej i cyfrowej anemometrii obrazowej.
-
Possibility of thermal imaging use in studies of natural convection heat transfer on the example of an isothermal vertical plate
Publikacja -
Comparison of predictive methods for flow boiling heat transfer in conventional channels and minichannels - the effect of reduced pressure
PublikacjaIn the paper are presented the results of follow on studies from [1]–[3] using authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data collected from various researchers to investigate the sensitivity of the in-house developed model. The collected experimental data came from various studies from literature and were conducted for the full...