Wyniki wyszukiwania dla: FINANSOWANIE START-UPÓW
-
AI Tech start 2022
Kursy Online -
Carbon dioxide potential reduction using Start-Stop system in a car
PublikacjaOperating fuel consumption increases significantly when the vehicle stops frequently while driving or when the engine is idling during braking. In such cases, the internal combustion engine consumes the fuel but the mechanical energy is not used by the drive system. The amount of fuel that is consumed in this time by the engine can potentially be saved if the car is equipped with a Stop-Start system. Start-Stop system automatically...
-
Finansowanie działalności MSP
Kursy Online -
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublikacjaThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
Finansowanie zadań oświatowych jednostek samorządu terytorialnego
PublikacjaCelem monografii jest przedstawienie, analiza i ocena procesu organizacji i finansowania zadań oświatowych w Polsce. W ujęciu szczegółowym w książce skupiono się opisie zasad organizacji i finansowania zadań oświatowych z punktu widzenia samorządu terytorialnego, w tym także zasad finansowania i przekazywania środków publicznych w formie dotacji placówkom prowadzonym przez podmioty inne niż jednostki samorządu terytorialnego. W...
-
Stanowisko do badania łożysk foliowych w cyklu start-stop
Publikacjastreszczenie: w artykule przedstawiono stanowisko do badań typu start-stop, które zostało zaprojektowane do testów przydatności materiałów i rozwiązań konstrukcyjnych aerodynamicznych łożysk foliowych. jest to jeden z modułów stanowiska badawczego wykorzystywanego w badaniach łożysk maszyn szybkoobrotowych opracowywanych w ramach projektu poig.01.03.01-00-027/08 pt. "wykorzystanie materiałów i konstrukcji inteligentnych do opracowania...
-
Stanowisko do badania łożysk foliowych w cyklu start-stop
PublikacjaStreszczenie: W artykule przedstawiono stanowisko do badań typu Start-Stop, które zostało zaprojektowane do testów przydatności materiałów i rozwiązań konstrukcyjnych aerodynamicznych łożysk foliowych. Jest to jeden z modułów stanowiska badawczego wykorzystywanego w badaniach łożysk maszyn szybkoobrotowych opracowywanych w ramach projektu POIG.01.03.01-00-027/08 pt. "Wykorzystanie materiałów i konstrukcji inteligentnych do opracowania...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
Start-up of a power unit of a thermal power plant auxiliary systems with supply from a hydropower plant
PublikacjaThis article discusses the issues related to a power unit of a thermal power plant start-up with the use of a hydropower plant. Hydropower plant can supply and will enable start-up of auxiliary equipment in a power unit of a thermal power plant. Due to high capacity of auxiliary drives, start-up of auxiliaries in a thermal power plant after blackout (and boiler shutdown) is not possible from emergency energy sources in the power...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublikacjaStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...