Wyniki wyszukiwania dla: heat transfer
-
Risk of power cables insulation failure due to the thermal effect of solar radiation
PublikacjaLow-voltage, as well as high-voltage power cable lines, are usually buried in the ground. The ampacity of the power cables in the ground mainly depends on the thermal resistivity of the soil, which may vary in a wide range. A common practice in power cable systems performance is to supply them from a pole of an overhead line. If so, a section of the line is located in free air and can be directly exposed to solar radiation. In...
-
Numerical simulation of hardening of concrete plate
PublikacjaThe paper presents a theoretical formulation of concrete curing in order to predict temperature evolution and strength development. The model of heat flow is based on a well-known Fourier equation. The numerical solution is implemented by means of the Finite Difference Method. In order to verify the model, the in situ temperature measurements at the top plate of a road bridge were carried out. A high agreement between numerical...
-
Quantitative study of free convective heat losses from thermodynamic partitions using Thermal Imaging
PublikacjaThe following paper presents a simple method of determining the presence, distribution and values of heat losses from external building walls as thermodynamic partitions using a Thermal Imaging Camera (TIC). According to Fourier's equation, the value of heat loss is proportional to the temperature gradient ∂t/∂y|y=0 in air in the y direction perpendicular to the heated surface. Unfortunately, air temperature cannot be measured...
-
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublikacjaThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
The In-House Method of Manufacturing a Low-Cost Heat Pipe with Specified Thermophysical Properties and Geometry
PublikacjaVarious types of heat pipes are available to purchase off the shelf, from various manufacturers, but most of them have strictly defined geometry and technical parameters. However, when there is a need to use a heat pipe (HP) with an unusual size and shape or working conditions other than the standard ones, it becomes very costly to order them from manufacturers, especially in small quantities, and only a few producers are willing...
-
A device for measuring heat flux on a rocket skin surface
PublikacjaA novel method for measuring heat flux on a surface is presented. It is an extensive upgrade of currently known heat flux sensors used mostly in civil engineering. As the thermal environment of launchers, especially sounding rocket can have an enormous negative effect on payload, careful considerations have to be taken in the process of preparing insulation. Usually, thermal data provided by the launch vehicle manufacturer is limited...
-
Preliminary results from HEDGEHOG REXUS project – A sounding rocket experiment on accelerations, vibrations and heat flow
PublikacjaDuring flight, a sounding rocket is subject to a unique environment - severe vibrations and substantial heat flux. In order to design payloads, precise measurement of these conditions is required. This paper presents preliminary results from HEDGEHOG REXUS Project, whose scientific goal was to characterise the thermal and dynamic environment of REXUS sounding rockets. For this purpose, two new sensors have been designed - mechanical...
-
A study of jet impingement cooling enhancement by concave and convex heat sink shape modifications
PublikacjaThe rising demand for efficient cooling technologies is a strong driver of extensive research in this area. This trend is particularly strong in turbines and microprocessors technology. Presented study is focused on the jet impingement cooling concept, which is used in various configurations for many years. The potential of the heat sink shape modification is not yet fully explored. Available literature suggests that average Nusselt...
-
Paweł Dąbrowski dr inż.
Osoby -
Michał Pysz mgr inż.
Osoby -
Moizuddin S. Khaja Doctoral Candidate
Osoby -
Mateusz Mielcarek
Osoby