Filtry
wszystkich: 1831
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: clamping diameter
-
Microgrinding with single-disk lapping kinematics.
PublikacjaGrinding operations are carried out with a variety of tool-workpiece configurations. The selection of a grinding process for a particular application depends on part shape, part size, ease of fixture, requirements concerning the acceptable shape errors. It is evident that lapping is very effective in eliminating the waviness while surface grinding is not. Dual disk machines for the double face grinding with planetary kinematics...
-
A method of predicting the best conditions for large-size workpiece clamping to reduce vibration in the face milling process
PublikacjaThe paper presents an innovative method of solving the problem of vibration suppression during milling of large-size details. It consists in searching for the best conditions for clamping the workpiece based on a rapid modal identification of the dominant natural frequencies only and requires repetitive changes in the tightening torque of the clamping screws. Then, by estimating the minimum work of the cutting forces acting in...
-
Experimental investigations on adiabatic frictional pressure drops of R134a during flow in 5mm diameter channel
PublikacjaThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a at a saturation pressure of 5.5 bar corresponding to the saturation temperature of 19.4 °C. Study cases have been set for a mass flux varying from 100 to 500 kg/m2 s. The frictional pressure drop was characterized for the refrigerant R134a, for vapor qualities ranging from 0 to 1. Long-time thermal stability of test facility allowed to gather...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublikacjaThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublikacjaW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...
-
The influence of height-do-diameter ratio on wind load of double-shell cylindrical, vertical tank
PublikacjaW pracy zaprezentowano skrót badań modelowych obciążenia wiatrem dwupłaszczowych zbiorników walcowych o różnych smukłościach aerodynamicznych. Przedstawiono wyniki pomiarów przeprowadzonych na dwóch modelach zbiorników z dachem pływającym i stosunku wysokości do średnicy płaszcza 0,45 i 0,25.
-
“DIY” Silica Nanoparticles: Exploring the Scope of a Simplified Synthetic Procedure and Absorbance-Based Diameter Measurements
Publikacja -
Zeta potential and effective diameter of n-tetradecane emulsions in n-propanol solutions and in the presence of lysozyme
Publikacja -
Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters
PublikacjaThe collision of two or more liquid jets may provide considerable atomisation and efficient mixing of injected substances at the same time. This phenomenon is used, among others, in rocket engines, where the fuel and oxidiser are introduced separately and almost immediately mixed through self-impingement. Depending on the injection and operating conditions, diverse configurations of impinging jets are used, such as doublets,...
-
Markers of Anemia in Children with Type 1 Diabetes
Publikacja -
Bone status in adolescents with type 1 diabetes
Publikacja -
Cognitive Dysfunction in Type 1 Diabetes Mellitus
Publikacja -
Benefits of hypertension management in diabetes: An opportunity not to be missed
Publikacja -
Optimization of clamping stiffness during milling of high-dimensional structures with the use of techniques of experiment – aided virtual prototyping
PublikacjaThe subject of this paper is a method of searching for conditions of minimizing the vibration level of a tool-high dimensional flexible workpiece, at unchangeable technological parameters of the machining process. It depends on repeatable change of the values of the stiffness coefficients as soon as an optimal vibration state of the workpiece approaches. There are assessed the values of dominant ”peaks” in the frequency spectra...
-
Experimentally Aided Operational Virtual Prototyping to Predict Best Clamping Conditions for Face Milling of Large-Size Structures
PublikacjaVibrations occurring during milling operations are one of the main issues disturbing the pursuit of better efficiency of milling operations and product quality. Even in the case of a stable cutting process, vibration reduction is still an important goal. One of the possible solutions to obtain it is selection of the favorable conditions for clamping the workpiece to the machine table. In this paper, a method for predicting and...
-
Influence of Flat Lapping Kinematics on Machinability of Ceramics
PublikacjaNew tools for flat grinding of ceramics are presented in the paper. Electroplated CBN tools (B64 and B107) were used in a modified single-disc lapping machine configuration. The results from experiments, such as the material removal rate and surface roughness parameters are presented and analyzed. Numerical simulations, based on the model for the shape error and tool wear estimation in machining with flat lapping kinematics, are...
-
Shaping of the workpiece surface in single-disc lapping
PublikacjaShape errors of the tool exert a dominant influence on the shape accuracy of the workpiece. The correlation between flatness errors of the lap and flatness errors of the workpieces was checked experimentally and determined analytically. Computer model of the workpiece shaping by lapping was developed. Evaluation method of the workpiece orientation as well as some simulation results for a lap with shape errors of convexity and cincavity...
-
Research on the wear evenness of the tool in flat lapping
PublikacjaIn this paper, the dimensionless distribution of the material removal stock and the trajectories of abrasive grains cutting in single-sided lapping process are presented. They were numerically simulated based on the tribological model and kinematics equations. It can be observed that the trajectories geometry of single abrasive as well the velocities have a great influence on the final geometrical deviation. During machining, the...
-
Results of abrasive slurry dosage in lapping process
PublikacjaPrzedstawiono wyniki badań dawkowania zawiesiny ściernej w docieraniu powierzchni płaskich elementów ceramicznych. Analizowano wpływ dawkowania na podstawowe parametry chropowatości powierzchni ceramiki Al2O3 i Al2O3-ZrO2.
-
Surface contamination after lapping by abrasive material
PublikacjaPrzedstawiono wyniki badań skażenia powierzchni żeliwa sferoidalnego mikroziarnami węglika krzemu po docieraniu. Określowo wpływ współczynnika upakowania mikroziaren w strefie docierania na intensywność skażenia powierzchni ścierniwem. W badaniach wykorzystano powierzchniową mikroanalizę rentgenowską.
-
The idea of a robotic single-sided lapping system
PublikacjaThis paper reviews the idea of a robotic lapping system. Robot’s assistance automates the lap-ping process and supports the development of a flexible lapping system. However, the main aim behind the idea of a robotic lapping system is to provide improved means for controlling the posi-tion of conditioning rings on a lapping plate. Due to the kinematics of lapping process, the profile wear of the tool is not constant along the radius....
-
Wave damping and smoothing in the unsteady pipe flow
Publikacjalaboratoryjne eksperymenty wykonane dla rur polietylenowych o różnej długości wykazały obecność takich zjawisk jak zmienna prędkość propagującej fali ciśnienia oraz jej intensywne tłumienie i wygładzanie. w artykule zaproponowano modyfikacje standardowych równań przepływu nieustalonego. polega ona na wprowadzeniu zmiennej prędkości fali oraz dyssypacji energii na jej czole opisanej członem dyfuzyjnym. do rozwiązania równań zaproponowano...
-
Analysis of flat compensator lapping in an assembly process
PublikacjaPrzedstawiono sposób analizy docierania kompensatora płaskiego podczas montażu połączenia konstrukcyjnego. Wyznaczono czas główny obróbki i koszty operacji docierania jednotarczowego
-
Problems of flat surface lapping : chapter 16
PublikacjaPrzedstawiono problemy docierania powierzchni płaskich w układach jednotarczowych. Omówiono analityczne i numeryczne modele kinematyki docierarek konwencjonalnych i niestandardowych, obróbkę docierakami aktywizowanymi w sposób swobodny i wymuszony, jednolitymi i dwumetalowymi. Zaprezentowano wyniki obróbki narzędziami ścierno-metalowymi elementów ceramicznych.
-
Shaping of the workpiece surface in single-disc lapping
PublikacjaPrzedstawiono korelację pomiędzy błędami kształtu docieraka i błędami kształtu przedmiotów obrabianych. Wyniki analityczne zostały sprawdzone doświadczalnie, co pozwoliło zbudować komputerowy model kształtowania powierzchni docieranych. Przedstawiono sposób wyznaczania intensywności kontaktu między przedmiotem docieranym, a docierakiem. Opracowano metodę wyznaczania położenia przedmiotu na docieraku.
-
Lapping of flat surfaces with two metallic tools.
PublikacjaPrzedstawiono opis docierania powierzchni płaskich docierakami aktywizowanymi w sposób swobodny i wymuszony oraz narzędziami dwumetalowymi i ściernometalowymi. Wyznaczono zużycie docieraków stalowo-żeliwnych oraz wydajność obróbki żeliwa sferoidalnego niestopowego i stali NC6.
-
Emissivity of the one-plate lapping machine tool
PublikacjaPrzedstawiono wyniki badań własnych emisyjności docieraka żeliwnego docierarki jednotarczowej. Omówiono konstrukcje produkowanych docierarek jednotarczowych wyposażonych w system kontroli temperatury lub chłodzenia tarczy docierającej. Podano warunki pomiarów temperatury przy użyciu kamery termowizyjnej typu V-20II firmy VIGO System S.A.
-
The Finite Pore Volume GAB Adsorption Isotherm Model as a Simple Tool to Estimate a Diameter of Cylindrical Nanopores
Publikacja -
Striking influence of NiO catalyst diameter on the carbonization of polypropylene into carbon nanomaterials and their high performance in the adsorption of oils
Publikacja -
Investigation of DPPC effect on SiO2 particles and in the presence of phospho(lipases) by zeta potential and effective diameter measurements
Publikacja -
Investigations of DPPC effect on Al2O3 particles in the presence of (phospho)lipases by the zeta potential and effective diameter measurements
Publikacja -
Effect of mean grain diameter on vortices, force chains and local volume changes in granular shear zones
PublikacjaW artykule pokazano rozwój różnych zjawisk mikrostrukturalnych na poziomie ziarna materiału granulowanego podczas parcia pasywnego piasku na sztywną ściankę przemieszczającą się poziomo. Obliczenia wykonano stosując metodę DEM. Wyniki na poziomie globalnym porównano z wynikami MES. Szczególna uwagę zwrócono na rozwój wirów i łańcuchów sił miedzy ziarnami.
-
DIABETES EDUCATOR
Czasopisma -
Journal of Diabetes
Czasopisma -
Diabetes Mellitus
Czasopisma -
Diabetes Therapy
Czasopisma -
Nutrition & Diabetes
Czasopisma -
Diabetes Aktuell
Czasopisma -
Diabetes Spectrum
Czasopisma -
Practical Diabetes
Czasopisma -
Clinical Diabetes
Czasopisma -
Diabetes Forecast
Czasopisma -
JMIR Diabetes
Czasopisma -
Investigations on mixture preparation for two phase adiabatic pressure drop of R134a flowing in 5 mm diameter channel
PublikacjaThe article presents detailed two-phase adiabatic pressure drops data for refrigerant R134a. Study cases have been set for a mass flux varying from 200 to 400 kg/m2 s, at the saturation temperature of 19.4 ◦C. Obtained experimental data was compared with the available correlations from the literature for the frictional pressure drop during adiabatic flow. Influence of mixture preparation on pressure drop was investigated, for...
-
A semi-empirical method for calculation of flow boiling heat transfer coefficients for conventional channels and small diameter tubes
PublikacjaW pracy przedstawiono rozważania na temat modelowania dwufazowego przepływu wrzącego w kanałach konwencjonalnych i w kanałach o małej średnicy. Przedstawiono modyfikację korelacji zaproponowanej wcześniej przez J. Mikielewicza na podstawie nowych danych eksperymentalnych, uzyskanych dla kanałów o małej średnicy. Bank danych obejmował ponad 460 punktów pomiarowych dla czynników R141b, R134a, R113, R123, R12, R11 i wody. Uzyskano...
-
Improved semi-empirical method for determination of heat transfer coefficient in flow boiling in conventional and small diameter tubes
PublikacjaPraca dotyczy przedstawienia poprawionego modelu umożliwiającego wyznaczanie współczynnika przejmowania ciepła w kanałach o małych średnicach jaj i tych tradycyjnych. Model zweryfikowano na 6 czynnikach chłodnuiczych uzyskując bardzo zadowalającą zgodność.
-
A pilot study to assess an in-process inspection method for small diameter holes produced by Direct Metal Laser Sintering
PublikacjaPurpose The purpose of this research is to evaluate the geometric quality of small diameter holes in parts printed by DMLS technology. An in-process optical inspection method is proposed and assessed during a pilot study. The influence of the theoretical hole diameter assumed in a CAD system and the sample thickness (hole length) on the hole clearance was analysed. Design/methodology/approach The samples made of two different...
-
Experimental investigation of M-shape heat transfer coefficient distribution of R123 flow boiling in small-diameter tubes
PublikacjaW publikacji przedstawiono wyniki badań wrzenia czynnika R123 w srebrnych rurkach o małych średnicach (średnice wewnętrzne wynosiły odpowiednio 1.15 mm i 2.3 mm). Badania przeprowadzono w szerokim zakresie stopnia suchości pary (0.01-0.9), gęstości strumienia masy (650-3000 kg/(m2s)) oraz gęstości strumienia ciepła (40-80 kW/m2). W badaniach wykazano, że istnieją dwa lokalne maksima współczynnika przejmowania ciepła w jego profilu...
-
Lipid peroxidation as a consequence of diabetes: effects of different treatment
Publikacja -
Prevalence of diabetes in Poland: a combined analysis of national databases
Publikacja