Search
Faculty of Mechanical Engineering and Ship Technology
Publications
Filters
total: 4536
displaying 1000 best results Help
Catalog Publications
Year 2022
-
The EU Tyre Noise Label: The problem with measuring the noise level of only a few of all tyre variants
PublicationThe STEER project, described in another Inter-Noise 2022 paper, has evaluated the performance of the noise label of the European tyre label. The major finding was that uncertainties of the tyre/road noise measurements were higher than should be accepted. One of the worst uncertainty sources was found to be the common practice to measure only some tyres of all sizes or variants within a tyre line, to save money. Generally, only...
-
The impact of surface slope and calculation resolution on the fractal dimension for fractures of steels after bending-torsion fatigue
PublicationThe article presents the results of the fractal dimension measurements on the fatigue fracture surfaces of 10HNAP and S355J2 steels specimens after combined bending-torsion fatigue. For smooth and ring-notched specimens, three loading conditions were analyzed: (1) bending; (2) bending-torsion; and (3) torsion fatigue. Post-failure surface topography measurements were carried out on the entire fracture surfaces using an optical...
-
The Latest Advances in Wireless Communication in Aviation, Wind Turbines and Bridges
PublicationPresent-day technologies used in SHM (Structural Health Monitoring) systems in many implementations are based on wireless sensor networks (WSN). In the context of the continuous development of these systems, the costs of the elements that form the monitoring system are decreasing. In this situation, the challenge is to select the optimal number of sensors and the network architecture, depending on the wireless system’s other parameters...
-
The Motion Analysis of Attacus Atlas Rigid Wing
PublicationThe remarkable aerodynamic efficiency of flapping insect wings has fascinated researchers for many years. Butterfly wings are distinguished by a much larger lifting surface, and thus, a different style of flapping flight. The considerations described in the article are an introduction to a fully flexible analysis of the wing in motion. The study of the rigid wing gives the basic knowledge necessary in the further process. The yaw,...
-
The potential of computational methods for the categorization of architectural objects on the example of media architecture
PublicationThe paper presents an example of the categorization of architectural objects and assessment of the characteristics of urban space, based on the analysis of specific features of architectural objects and urban landscape. The conducted analysis refers to media architecture and is presented in the complex context of the development of media solutions. The field of influence of IT on architecture is also stressed, both on the architect’s...
-
The vibration-based assessment of the influence of elevated temperature on the condition of concrete beams with pultruded GFRP reinforcement
PublicationConcrete beams reinforced with glass fiber reinforced polymer (GFRP) bars subjected to elevated temperature have been experimentally studied. The influence of high temperatures on GFRP-reinforced concrete beams condition has been check both, destructively and nondestructively. The nondestructive tests foresaw vibration-based tests to obtain the natural frequency values after exposure to varying temperatures. The vibration-based...
-
Thermal cooling process by nanofluid flowing near stagnating point of expanding surface under induced magnetism force: A computational case study
PublicationThis paper is dedicated to the exam of entropy age and research of the effect of mixing nanosolid additives over an extending sheet. In this review, Newtonian nanofluid version turned into researched at the actuated appealing field, heat radiation and variable heat conductivity results. With becoming modifications, the proven PDEs are moved into popular differential situations and paintings mathematically making use of a specific...
-
Thermal Energy Development in Magnetohydrodynamic Flow Utilizing Titanium Dioxide, Copper Oxide and Aluminum Oxide Nanoparticles: Thermal Dispersion and Heat Generating Formularization
PublicationThe main aim of this article heat transfer in thermal engineering deals with the production, use, transformation, and transfer of thermal energy. Engineering and industrial fields including food packaging, the production of food additives, electronic cooling, microturbines, etc. heavily rely on heat transmission. Due to its intriguing potential in industries like the production of polymers, paper, crystal glass, etc., scientists...
-
Thermodynamic, ecological, and economic analysis of negative CO2 emission power plant using gasified sewage sludge
PublicationCurrently, sewage sludge is considered as a biomass, according to the Polish act on renewable energy sources from 20th of February 2015 and its novel version from 19th of July 2019. Possibility to utilize sewage sludge in gasification process is an additional advantage of the negative CO2 emissions power plant (nCO2PP). The work presents results of thermodynamic, ecological, and economical analysis using a zero-dimensional mathematical...
-
Three-Dimensional Fractography for Conventional and Additive Manufactured Steels After Bending-Torsion Fatigue
PublicationIn this study, fracture surface topography parameters were measured to investigate the effects of multiaxial loading. In order to assess the metrological aspects of fracture for notched specimens made of high-strength steels processed by both conventional and additively manufacturing (AM) techniques, an optical surface profilometer was used. Three bending moment to torsion moment ratios (B/T) were studied, i.e. 2, 1 and 2/3. The...
-
Towards an Understanding of the Stability Assessment of Floating Buildings
PublicationOne of the most important aspects of the design of floating facilities such as ships, floating offshore structures or floating houses is stability. Its impact on both general safety and operational aspects renders it a fundamental consideration already in preliminary design stages. Usually, the concept of sufficient stability of floating buildings is associated with the ability to keep an allowed heel angle and residual freeboard,...
-
Towards classification of patients based on surface EMG data of temporomandibular joint muscles using self-organising maps
PublicationThe study considers the need for an effective method of classification of patients with a temporomandibular joint disorder (TMD). The self-organising map method (SOM) was applied to group patients and used together with the cross-correlation approach to interpret the processed (rectified and smoothed by using root mean square (RMS) algorithm) surface electromyography signal (sEMG) obtained from testing the muscles (two temporal...
-
Towards Designing an Innovative Industrial Fan: Developing Regression and Neural Models Based on Remote Mass Measurements
PublicationThis article presents the process of the construction and testing a remote, fully autonomous system for measuring the operational parameters of fans. The measurement results obtained made it possible to create and verify mathematical models using linear regression and neural networks. The process was implemented as part of the first stage of an innovative project. The article presents detailed steps of constructing a system to...
-
Towards evaluation of the Second Generation Intact Stability Criteria - examination of a fishing vessel vulnerability to surf-riding, based on historical capsizing
PublicationThe Second Generation Intact Stability Criteria (SGISC) are the latest achievements in the field of intact ship stability assessment. The criteria are the result of massive international cooperative efforts and extensive research that lasted more than 15 years. Even though they are based on a solid scientific foundation, the trial period has commenced to collect user experience and further validation. One of possible approaches...
-
Tribological Properties of Thermoplastic Materials Formed by 3D Printing by FDM Process
PublicationThe dataset entitled 3D printed ABS thermoplastic vs. steel. Dry sliding wear test in constant load & velocity ring on flat configuration. Test parameters: print layer thickness and orientation. Test symbol: 019_h_4 contains: the time base (expressed in seconds and minutes), the friction torque for sliding friction, rotational velocity of the counter – specimen (velocity of sliding), friction coefficient, load in the friction contact...
-
Tyre/road noise measurements on ISO tracks according to the UNECE Regulation 117
PublicationWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on 3 ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance, and this directive is based on the measurement procedures defined in the UN ECE Reg.117. The same test car, test tyres and measurement equipment as well as personnel were used...
-
Tyre/road noise measurements on ISO tracks using the modified CPX method
PublicationTyre rolling noise test method specified in the UNECE Regulation 117 is directly used in the Tyre Labelling Directive. Noise level specified on EU Tyre Label of each new tyre available on the European market was determined based on vehicle coast-by noise measurements performed on the standard reference road surface proscribed in the ISO 10844:2014. Available data from investigations by the vehicle and tyre industry and results...
-
Underwater Processing of Materials
PublicationEditorial do SI
-
Underwater wet welding of S1300 ultra-high strength steel
PublicationMarine Structures Volume 81, January 2022, 103120 Underwater wet welding of S1300 ultra-high strength steel Author links open overlay panelJacekTomkówGrzegorzRogalski https://doi.org/10.1016/j.marstruc.2021.103120 Get rights and content Under a Creative Commons licenseopen access Highlights • Technological method of S1300 steel underwater weldability improving was proposed. • Number of cracks and hardness of welded joints was...
-
Using differential pressure sensor to measure nitrous oxide level in a tank
PublicationA method for measuring the level of liquid nitrous oxide oxidizer in a hybrid rocket motor oxidizer tank is proposed. Presented approach is more accurate than the most commonly used method of this measurement, which employs weighting of the whole sounding rocket or an oxidizer tank. In our solution we use a differential pressure sensor to measure the change of pressure at the bottom of an oxidizer tank in comparison to the pressure...
-
Verification of the method of reconstructing convective velocity fields on the basis of temperature fields in vertical, differential and equally heated, open and closed channels
PublicationThis paper describes a method of reconstructing velocity fields, i.e. a numerical reconstruction procedure (NRP) that involves the numerical processing of experimentally measured temperature distributions in free convection heat transfer. The NRP consists in solving only the continuity and Navier–Stokes equations with an additional source term. This term is proportional to a known temperature (e.g. from a thermal imaging camera)...
-
Vibration-Based Investigation of a Historic Bell Tower to Understand the Occurrence of Damage
PublicationABSTRACT The paper presents a survey of the historic Arch-cathedral bell tower in Vilnius induced by the appearance of cracks in the structure after a new bell system installation. An attempt is undertaken to identify the reason for the crack occurrence and to check a possible crack influence on global structural behaviour. The research is based on dynamic measurements made in the tower during ambient vibrations and during vibrations...
-
Weather Routing System Architecture Using Onboard Data Collection and Route Optimisation
PublicationThis paper describes the architecture of a weather routing system consisting of two key elements: onboard monitoring and route optimiser sub-systems. The former is responsible for collecting various onboard measurements, such as current ship position or ship motion variables. These data, when gathered and processed, are then used for fine-tuning a ship model. The model, together with weather forecasts, is utilised by a multi-objective...
-
Whether Carbon Nanotubes Are Capable, Promising, and Safe for Their Application in Nervous System Regeneration. Some Critical Remarks and Research Strategies
PublicationCarbon nanotubes are applied in or considered for different fields of medicine. Among them is the regeneration or rebuilding of nervous system components, which still lack substantial progress; this field is supported by carbon nanotubes to a great extent as the principal material. The limited research on this issue has involved PU/silk/MWCNTs, PCL/silk/MWCNTs, PCL/PGS/CNTs, chitin/CNTs, PGF/CNTs, CNTs/PGFs/PLDLA,MWCNTs chitosan,MWCNTs/PPy,...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublicationWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
Wpływ środowiska i warunków zamocowania na drgania elementów obiektów wynoszonych w przestrzeń kosmiczną
PublicationRozprawa doktorska dotyczy zagadnienia analizy wpływu ciśnienia atmosferycznego i siły docisku na współczynnik tłumienia drgań mechanicznych. Głównym celem pracy było sformułowanie opisu oddziaływania otoczenia obiektów drgających w warunkach wynoszenia w przestrzeń kosmiczną na parametry tych drgań. Przedstawiono przegląd literatury dotyczący sposobu pomiaru oraz metod identyfikacji parametrów drgań, zagadnienia tribologii oraz...
-
WPŁYW UŁOŻENIA I RODZAJU ZASTOSOWANYCH WŁÓKIEN WĘGLOWYCH NA WYTRZYMAŁOŚĆ KOMPOZYTU DLA MONOCOQUE’A BOLIDU FORMUŁY STUDENT
PublicationCelem niniejszej pracy jest przetestowanie jaki wpływ ma sposób ułożenia oraz rodzaj zastosowanych włókien węglowych na wytrzymałość elementu kompozytowego. Poprzez sprawdzenie czterech rodzajów próbek badawczych w dwóch oddzielnych testach stanie się możliwe stwierdzenie, który typ próbki charakteryzuje się największą wytrzymałością dla przyjętych założeń badawczych. Dzięki temu zbadany rodzaj kompozytu zostanie zastosowany w...
-
WPŁYW USTAWIENIA GEOMETRII ZAWIESZENIA NA OPORY RUCHU I ZUŻYCIE PALIWA W POJAZDACH WYŚCIGOWYCH
PublicationCelem przeprowadzonych prac było sprawdzenie wpływu konstrukcji i ustawień zawieszenia pojazdu klasy Formuła Student na opory ruchu, a co za tym idzie zużycie paliwa. Przeprowadzenie badań w postaci pomiarów zużycia paliwa oraz czasów przejazdów okrążeń na torze w różnych konfiguracjach układu zawieszenia wymagało stworzenia kompletnego układu zawieszenia, które zostało zastosowane w konstrukcji PGR-05 zespołu PGRacing Team. Na...
-
Wpływ warunków zgrzewania metodą Friction Stir Welding na własności mechaniczne i jakość złączy ze stopu aluminium
PublicationW prezentacji przedstawiono wyniki badań nad wpływem warunków zgrzewania metodą FSW na jakość połączeń ze stopów aluminium.
-
Wpływ warunków zgrzewania metodą Friction Stir Welding na własności mechaniczne i jakość złączy ze stopu aluminium
PublicationCelem niniejszych badań było porównanie wpływu kształtu narzędzia na złącze oraz uzyskanie wartości parametrów zgrzewania tarciowego z przemieszaniem (FSW) zapewniających najlepszą możliwą jakość złącza. Zastosowanym materiałem był stop aluminium EN AW-3004 (AlMn1Mg1). Według najlepszej wiedzy autorów dotychczas nie przedstawiono żadnych badań tego stopu w kwestii zgrzewania FSW. Złącza pięcioczołowe wykonano samodzielnie opracowanym...
-
WYNIKI SYMULACJI NUMERYCZNEJ CYKLU ROBOCZEGO SILNIKA O ZS W PROGRAMIE DIESEL-RK ORAZ OCENA ICH UŻYTECZNOŚCI W PROCESIE PLANOWANIA BADAŃ DIAGNOSTYCZNYCH OKRĘTOWEGO SILNIKA TŁOKOWEGO
PublicationW artykule przedstawiono wyniki symulacji numerycznej procesu roboczego realizowanego w silniku tłokowym o zapłonie samoczynnym. W zastosowanym programie użytkowym DIESEL-RK zaimplementowano silnik laboratoryjny Farymann Diesel typ D10. Wprowadzono wybraną niesprawność jego układu funkcjonalnego zasilania paliwem - obniżone ciśnienie otwarcia wtryskiwacza pwtr. Wyznaczono wartości adekwatnych parametrów diagnostycznych: temperaturę...
-
Wyszukiwanie źródła sygnału przy użyciu grupy robotów
PublicationW pracy przedstawiono algorytm wyszukiwania źródła sygnału oparty na zmodyfikowanej metodzie wyszukiwania źródła sygnału RSSI. Fizyczna implementacja tego algorytmu opiera się na wykorzystaniu losowo rozłożonych dwukołowych robotów poruszających się w formacji roju. Uzyskane wyniki z badań doświadczalnych wskazują, że proponowana fizyczna implementacja algorytmu w przeprowadzonych próbach pozwoliła na uzyskanie średniej dokładności...
-
Z historii Stowarzyszenia Inżynierów i Techników Polskich w Szwajcarii
PublicationPrzedstawiono, pokrótce, historię i działalność Stowarzyszenia Inżynierów i Techników Polskich w Szwajcarii. Wspomniano o związkach polskich naukowców pracujących w szwajcarskich uczelniach, w pierwszych latach powojennych, z Politechniką Gdańską.
-
Z historii Stowarzyszenia Techników i Inżynierów Polskich na Litwie
PublicationPrzedstawiono pokrótce historię Stowarzyszenia Techników i Inżynierów Polskich na Litwie. Wskazano na związki STIP z Europejską Federacją Polonijnych Stowarzyszeń Naukowo-Technicznych oraz z FSNT NOT. Scharakteryzowano działalność patrona Stowarzyszenia Techników i Inżynierów na Litwie Rafała Kalinowskiego.
-
Zastosowanie przedmiotowych uchwytów modułowych w operacjach wytwarzania na przykładzie obróbki korpusu.
PublicationOmówiono zastosowanie przedmiotowych uchwytów modułowych w operacjach obróbkowych. Przedstawiono dwa warianty technologii korpusu jednolitego. Omówiono konstrukcje wykorzystywanych uchwytów modułowych oraz ich koszt i czasochłonność analizowanych operacji na dwóch centrach obróbkowych, o pionowej i poziomej osi wrzeciona.
-
Zmiennofazowy akumulator ciepła w dolnym źródle pompy ciepła – propozycja dla budynku jednorodzinnego
PublicationW artykule przedstawiono autorskie rozwiązanie zmiennofazowego akumulatora ciepła, w którym jawne i utajone ciepło szarych ścieków jest odbierane za pomocą prototypowego wymiennika ciepła posadowionego w akumulatorze i sprzęgniętego z parownikiem pompy ciepła. Ścieki szare dopływają do akumulatora z budynku jednorodzinnego. Układ funkcjonuje w systemie grzewczym tego budynku. Omówiono doświadczenia z dotychczasowej eksploatacji...
-
Znaczenie mocy testu statystycznego w analizie diagnostycznej okrętowego silnika o ZS
PublicationW artykule przedstawiono sposób interpretacji błędów pierwszego (α) i drugiego (β) rodzaju oraz wartości krytycznej Fkr rozkładu Fishera-Snedecora. Omówiono dwa sposoby weryfikacji istotności wpływu parametru wejściowego na wyjściowy. Przeanalizowano znaczenie mocy testu statystycznego M w diagnostyce parametrycznej okrętowych silników o ZS. Przeprowadzono analizę wpływu wartości poziomu istotności na wartość krytyczną statystyki...
Year 2021
-
A comparative performance assessment of a hydrodynamic journal bearing lubricated with oil and magnetorheological fluid
PublicationThis work presents the investigation results of a journal bearing lubricated with magnetorheological fluid that is activated by a local constant magnetic field to vary both the local flow resistance and pressure. The bearing performance is assessed via Finite Element Modelling (FEM) and results are corroborated by experiments. The FEM model uses the Bingham model to describe the fluid film. A dedicated test rig is used to assess...
-
A device for measuring heat flux on a rocket skin surface
PublicationA novel method for measuring heat flux on a surface is presented. It is an extensive upgrade of currently known heat flux sensors used mostly in civil engineering. As the thermal environment of launchers, especially sounding rocket can have an enormous negative effect on payload, careful considerations have to be taken in the process of preparing insulation. Usually, thermal data provided by the launch vehicle manufacturer is limited...
-
A method of predicting the best conditions for large-size workpiece clamping to reduce vibration in the face milling process
PublicationThe paper presents an innovative method of solving the problem of vibration suppression during milling of large-size details. It consists in searching for the best conditions for clamping the workpiece based on a rapid modal identification of the dominant natural frequencies only and requires repetitive changes in the tightening torque of the clamping screws. Then, by estimating the minimum work of the cutting forces acting in...
-
A Pilot Study on Machining Difficult-to-Cut Materials with the Use of Tools Fabricated by SLS Technology
PublicationThe growing use of contemporary materials in various industrial sectors, such as aerospace, automotive, as well as the oil and gas industry, requires appropriate machining methods and tools. Currently, apart from the necessity to obtain high-dimensional and shape accuracy, the efficiency and economic aspects of the selected manufacturing process are equally important, especially when difficult-to-cut materials, such as hard and...
-
A pilot study to assess manufacturing processes using selected point measures of vibroacoustic signals generated on a multitasking machine
PublicationThe article presents the method for the evaluation of selected manufacturing processes using the analysis of vibration and sound signals. This method is based on the use of sensors installed outside the machining zone, allowing to be used quickly and reliably in real production conditions. The article contains a developed measurement methodology based on the specific location of microphones and vibration transducers mounted on...
-
A review on application of artificial neural network (ANN) for performance and emission characteristics of diesel engine fueled with biodiesel-based fuels
PublicationBiodiesel has been emerging as a potential and promising biofuel for the strategy of reducing toxic emissions and improving engine performance. Computational methods aiming to offer numerical solutions were inevitable as a study methodology which was sometimes considered the only practical method. Artificial neural networks (ANN) were data-processing systems, which were used to tackle many issues in engineering and science, especially...
-
A ship domain-based model of collision risk for near-miss detection and Collision Alert Systems
PublicationThe paper presents a new model of ship collision risk, which utilises a ship domain concept and the related domain-based collision risk parameters. An encounter is here described by five variables representing: degree of domain violation (DDV), relative speed of the two vessels, combination of the vessels’ courses, arena violations and encounter complexity. As for the first three variables, their values can be directly computed...
-
A study of jet impingement cooling enhancement by concave and convex heat sink shape modifications
PublicationThe rising demand for efficient cooling technologies is a strong driver of extensive research in this area. This trend is particularly strong in turbines and microprocessors technology. Presented study is focused on the jet impingement cooling concept, which is used in various configurations for many years. The potential of the heat sink shape modification is not yet fully explored. Available literature suggests that average Nusselt...
-
A technique of experiment aided virtual prototyping to obtain the best spindle speed during face milling of large-size structures
PublicationThe paper presents an original method concerning vibration suppression problem during milling of large-size and geometrically complicated workpieces with the use of novel way of selecting the spindle speed. This consists in repetitive simulations of the cutting process for subsequent values of the spindle speed, until the best vibration state of the workpiece is reached. An appropriate method of obtaining a computational model,...
-
Advanced super-hydrophobic polymer-based porous absorbents for the treatment of oil-polluted water
PublicationThe threat of environmental pollution caused by spilled oil is rapidly increasing along with the expansion of oil exploration, the development of maritime activities and industrial growth. Oil spill incidents usually affect seriously the ecosystem and human life. Therefore, the treatment and recovery of the oil spill have been considered as an ultra-important issue to protect the environment and to minimize its negative impacts...
-
ADVANCES IN MATERIALS SCIENCE EDITORIAL ON THE JOURNAL'S 20th ANNIVERSARY
PublicationEditorial on the occasion of the 20th anniversary of Advances in Materials Science journal.
-
An Experimentally Aided Operational Virtual Prototyping to Obtain the Best Spindle Speed during Face Milling of Large-Size Structures
PublicationAbstract: The paper presents an original method concerning the problem of vibration reduction in the general case while milling large-size and geometrically complex details with the use of an innovative approach to the selection of spindle speed. A computational model is obtained by applying the so-called operational approach to identify the parameters of the workpiece modal model. Thanks to the experimental modal analysis results,...
-
An Improved Method of Minimizing Tool Vibration during Boring Holes in Large-Size Structures
PublicationThe paper presents a thoroughly modified method of solving the problem of vibration suppression when boring large-diameter holes in large-size workpieces. A new approach of adjusting the rotational speed of a boring tool is proposed which concerns the selection of the spindle speed in accordance with the results of the simulation of the cutting process. This streamlined method focuses on phenomenological aspects and involves the...