Filters
total: 459
Search results for: FE METHOD
-
Imaging of grains and internal stresses in GO Fe-Si alloy with Barkhauseneffects
PublicationBadano próbki stali transformatorowej Fe-Si ze strukturą zorientowaną (GO). Polowy efekt Barkhausena wykorzystano do zobrazowania ziaren pod warstwą ochronną a poziom naprężeń wewnętrznych wyznaczono wykorzystując mechaniczny efekt Barkhausena.
-
XPS measurements of the Fe-Pb-Si based glass
Open Research DataGlass samples with nominal compositions of xFe2O3-(50-x)PbO–50SiO2, where x = 12.5, 15, 17.5 (mol%) were prepared. Analytical grade substrates were used: Fe2O3, SiO2, and PbO. The appropriate amounts of reagents were mixed in an agate mortar. The powders obtained were melted in porcelain un-enamelled crucibles in an electric furnace at a temperature...
-
Effect of laser heating on cavitation behaviour of Fe-Cr-Mn coating.
PublicationW pracy przedstawiono badania odporności kawiracyjnej napoiny Fe-Cr-Mn po obróbce laserowej polegającej na przetapianiu napoiny wiązką lasera CO2 o mocy 1000W oraz jej nagrzewaniu w stanie stałym. Rezultaty badań wskazują,że po każdym rodzaju obróbki występuje inna podatność obrobionej powierzchni do odkształceń plastycznych pod działaniem obciążeń kawitacyjnych.
-
Shear fracture of longitudinally reinforced concrete beams under bending using Digital Image Correlation and FE simulations with concrete micro-structure based on X-ray micro-computed tomography images
PublicationThe paper presents experimental and numerical investigations of the shear fracture in rectangular concrete beams longitudinally reinforced with steel or basalt bar under quasi-static three point bending. Shear fracture process zone formation and development on the surface of beams was investigated by Digital Image Correlation (DIC) whereas thorough analyses of 3D material micro-structure, air voids, width and curvature of shear...
-
Periodic Properties of 1D FE Discrete Models in High Frequency Dynamics
PublicationFinite element discrete models of various engineering 1D structures may be considered as structures of certain periodic characteristics. The source of this periodicity comes from the discontinuity of stress/strain field between the elements. This behaviour remains unnoticeable, when low frequency dynamics of these structures is investigated. At high frequency regimes, however, its influence may be strong enough to dominate calculated...
-
La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ oxygen electrodes for solid oxide cells prepared by polymer precursor and nitrates solution infiltration into gadolinium doped ceria backbone
PublicationInfiltration is a method, which can be applied for the electrode preparation. In this paper oxygen electrode is prepared solely by the infiltration of La0.6Sr0.4Co0.2Fe0.8O3‐δ (LSCF) into Ce0.8Gd0.2O2-δ (CGO) backbone. The use a polymer precursor as an infiltrating medium, instead of an aqueous nitrate salts solution is presented. It is shown that the polymer forms the single-phase perovskite at 600 °C, contrary to the nitrates...
-
Fabrication, microstructure and properties of Al-Si -Fe-Cu in situ composites.
PublicationW poszukiwaniu tanich kompozytów na bazie stopów Al powstała koncepcja otrzymywania kompozytów in situ o osnowie stopu Al-Si w reakcji ciekłego stopu Al-Si (Al-Si11, Al-Si25) z proszkiem Fe. Powstałe wydzielenia np. iglastego AlFe4Si w stopie AlSi25 o niezbyt wysokiej twardości (rys.2) stanowią skuteczne wzmocnienie stopu pod względem twardości, sztywności i wytrzymałości na ściskanie jak też obniżonej ścieralności. Jednak znaczny...
-
Impact of plastic deformation on magnetoacoustic properties of Fe-2%Si alloy
PublicationW artykule przedstawiono wyniki komplementarnych badań własności magnetycznych stopu Fe-2%Si po deformacji plastycznej. Badania obejmowały pomiary pętli histerezy magnetycznej B(H), magnetycznego efektu Barkhausena oraz emisjii magnetoakustycznej. Badane próbki poddane były deformacji plastycznej do poziomu sięgajćego 8%. Właściwości pętli histerezy zostały skwantyfikowane z wykorzystaniem pola koercji oraz maksymalnej magnetycznej...
-
Magnetically induced dynamical stability of a Fe monolayer on W(110)
Publication -
Fe analysis of loadson the silo wall and stresses in the silo structure.
PublicationArtykuł przedstawia numeryczne wyniki naporu materiałów sypkich na ścinanie podczas przepływu w silosach z lejem w kształcie osiowo-symetrycznego stożka.
-
Impact of low-temperature sintering on the Fe-based amorphous coatings
PublicationBulk metallic glasses (BMGs) have gained a lot of attention in recent years due to their outstanding properties such as high hardness and excellent wear and corrosion resistance. However, they are restricted in industrial applications due to their extreme brittleness. Iron based amorphous coatings from BMGs are the best solution to use them by overcoming the problem of extreme brittleness. The coatings can be sprayed by various...
-
FE analysis of reinforced concrete corbels with enhanced continuum models
PublicationW artykule pokazano wyniki MES symulacji wsporników żelbetowych. Zachowanie wsporników modelowano przy zastosowaniu 3 różnych modeli betonu: sprężysto-plastycznego, degradacji sprężystej i rozmytych rys. Modele rozszerzono o długość mikrostruktury przy zastosowaniu teorii nielokalnej. Wyniki numeryczne porównano z doświadczeniami z literatury.
-
FE-simulations of size effects in granular and quasi-brittle materials
PublicationW artykule przedstawiono symulacje efektów skali w materiałach granulowanych i kruchych. Obliczenia wykonano dla ściskania dwuosiowego i fundamentu w przypadku materiałów granulowanych oraz belek zginanych w przypadku materiałów kruchych. Do obliczeń wykorzystano mikropolarne prawo hipoplastyczne i sprężysto-plastyczne prawo z nielokalnym osłabieniem.
-
FE-analysis of contractant shear zones in loose granular materials
PublicationW artykule przedstawiono wyniki numerycznej analizy stref ścinania w materiałach granulowanych luźnych. Obliczenia wykonano dla 4 różnych problemów brzegowych: ścinania warstwy między dwoma bardzo szorstkimi ścianami, ściskania w płaskim stanie odkształcenia, dwuosiowego ściskania, odporu na ściankę. Obliczenia wykonano stosując metodę elementów skończonych na bazie mikropolarnego prawa hipoplastycznego.
-
FE-simulations of direct and simple shearing within a polar hypoplasticity
PublicationW artykule przedstawiono wyniki analizy MES dwóch podstawowych testów w mechanice gruntów, mianowicie testu bezpośredniego ścinania i testu prostego ścinania. Obliczenia wykonano stosując metodę elementów skończonych i mikropolarne hipoplastyczne prawo konstytutywne. Szczególną uwagę zwrócono na wpływ warunków brzegowych na lokalizacje odkształceń.
-
FE-analysis of shearing of granular bodies in a direct shear box
PublicationW artykule przedstawiono wyniki numerycznej obszernej analizy testu bezpośredniego ścinania. w materiałach granulowanych. Obliczenia wykonano stosując metodę elementów skończonych i mikropolarne hipoplastyczne prawo konstytutywne. Analizę wykonano dla różnego poziomu obciażenia, długości charakterystycznej, wskaźnika porowatości, długości próbki W analizie uwzględniono lokalizacje odkształceń stycznych.
-
Magneto-mechanical properties evolution of Fe-C alloy during precipitation process.
PublicationZbadano pętlę histerezy magnetycznej oraz natężenia mechanicznego i polowego efektu Barkhausena w stopie Fe-C w funkcji czasu wygrzewania izotermicznego w temperaturze 473 K. Wyznaczono rozkłady poziomu naprężeń wewnętrznych oraz straty energii na procesy histerezowe. Wykazano, iż pole koercji Hc jest paraboliczną funkcją średniego poziomu naprężeń sigma-i.
-
Influence of laser beam machining on the cavitation resistance of Fe-Cr-Co clad.
PublicationW pracy przedstawiono wpływ laserowego nagrzewania bezzmiany stanu skupienia i laserowego przetapiania napoin ze stopu Fe-Cr-Co na ich odporność kawitacyjną. Badania kawitacyjne prowadzono na stanowisku z wirującą tarczą. Plastyczne odkształcenia powierzchni określano za pomocą analizy obrazów erodowanych powierzchni. Uzyskane rezultaty wskazują, że laserowo obrabiane powierzchnie miały różną podatność do plastycznego odkształcania...
-
Depth XPS profile of Fe-S layers on a titanium substrate
Open Research DataDepth XPS profile of Fe-S layers on a titanium substrate was measured. Material was etched by Argon ion gun and measured by XPS method. For each sample, three times per 10 minutes each was sputtered.
-
XPS measurement of the Fe-Ti based materials
Open Research DataThe mono‐ and bimetal‐modified (Pd, Cu) titanium(IV) oxide and iron oxide (III) photocatalysts were prepared by chemical reduction method and characterized using XPS method. The composition of elements incorporated in the surface layer of mono- and bimetallic photocatalysts was determined by XPS analysis, as well as the valence state of elements. Measurements...