Search
Search results for: SAWDUST
-
Sorption of Chlorinated Solvents on Pine and Oak sawdust
PublicationThe article presents assessment of pine and oak sawdusts as sorbents for removal of chlorinated solvents from water. Sawdusts as potential sorbents were characterized with elemental analysis and BET analyses. Sorption capacity was determined for both pine and oak sawdust towards 1,1,2-trichloroethane, tetrachloroethene and 1,1,1,2-tetrachloroethane. Pine sawdust was able to adsorb greater amounts of chlorinated solvents compared...
-
Bio-Based Polyurethane Networks Derived from Liquefied Sawdust
PublicationThe utilization of forestry waste resources in the production of polyurethane resins is a promising green alternative to the use of unsustainable resources. Liquefaction of wood-based biomass gives polyols with properties depending on the reagents used. In this article, the liquefaction of forestry wastes, including sawdust, in solvents such as glycerol and polyethylene glycol was investigated. The liquefaction process was carried...
-
Granulometric characterization of Arctic driftwood sawdust from frame sawing process
PublicationArctic driftwood can be used as an alternative source of wood as construction timber and furniture material, especially in Iceland and Greenland. The use of Arctic driftwood can help in the fight against climate change, by developing land reforestation processes and reducing the volume harvested wood from forests and sustainability of harvesting processes. In this paper the results of an analysis of the effect of long-term residence...
-
Optimal selection of the sawdust separation device for a narrow-kerf sawing machine PRW15-M
PublicationW pracy przedstawiono granulometryczną analizę rozkładu wiórów i pyłu drzewnego otrzymanego w procesie przecinania suchych pryzm sosnowych na pilarce ramowej wielopiłowej PRW15-M. Wielkości wiórów mieściły się w granicach od 84,7 μm do nawet 14 mm. Te ostatnie są elementami będącymi efektem rozszczepiania dolnej powierzchni pryzmy przez wychodzące z niej ostrza piły. Większośc wiórów z najmniejszych frakcji ma postać sześciennych...
-
THE EFFECT OF WOOD DRYING METHOD ON THE GRANULARITY OF SAWDUST OBTAINED DURING THE SAWING PROCESS USING THE FRAME SAWING MACHINE
PublicationThe experimental results of the study focused on the effect of drying processes of warm air drying at the temperature of 6580°C and warm air-steam mixture drying at the temperature of 105°C of pine and beech wood to the size of sawdust grains created by cutting using RPW 15M frame saw is presented in the paper. Particle size analysis of dry sawdust was performed using two methods - screening method and optical method based on...
-
Effect of thermal modification of oak wood on sawdust granularity = Utecaj termicke modifikacije na granulometrijski sastav piljevine
PublicationW pracy przedstawiono wyniki badania składu granolumetrycznego trocin po przecinaniu na pilarce ramowej wielopiłowej PRW15M drewna dębowego (przed i po obróbce termicznej). Wykazano, że uzyskiwane trociny z drewna po modyfikacji termicznej charakteryzują się większym udziałem frakcji drobnych.
-
Sawdust size distribution analysis of thermally modified and unmodified oak wood sawed on the frame sawing machine PRW15-M
PublicationW pracy przedstawiono wyniki analizy granulometrycznej składu wiórów drewna dębowego niemodyfikowanego i modyfikowanego termicznie uzyskanych podczas piłowania na pilarce ramowej PRW15-M z prędkością posuwu 1.67 mmin-1. Otrzymane trociny termicznie modyfikowanego drewna dębowego składają się z wiórów o ziarnistości w przedziale od 44.7 mm do 4.6 mm, podczas gdy dla drewna niemodyfikowanego zaobserwowano zmiany ziarnistości w granicach...
-
The Biotic and Abiotic Carbon Monoxide Formation During Aerobic Co-digestion of Dairy Cattle Manure With Green Waste and Sawdust
Publication -
Influence of feed rate on the granularity and homogenity of oak sawdust obtained during the sawing process on the frame sawing machine PRW15M
PublicationOpisano wpływ prędkości posuwu na skład granulometryczny i jednorodność trocin dębowych otrzymanych podczas procesu przecinania na pilarce ramowej PRW15M. Wykazano, że otrzymane trociny mogą być wykorzystane w produkcji produktów drewnopochodnych w ilości 75% dla posuwu 0.36 m/min i 82% przy posuwie 1.67 m/min. Pozostałe trociny stanowią odpad.
-
The effect of thermal modification of ash wood on granularity and homogeneity of sawdust in the sawing process on a sash gang saw PRW 15-M in view of its technological usefulness
PublicationPrzedstawiono wyniki analiz granulometrycznych trocin, drewna jesionowego niemodyfikowanego (Fraxinus exelsior L.) i modyfikowanego termicznie, otrzymanych w procesie przecinania drewna na pilarce ramowej wielopiłowej PRW15-M. Przecinanie drewna prowadzono dla dwu prędkości posuwu 0,36 m·min-1 oraz 1,67 m·min-1. Ziarnistośćpowstających trocin dla drewna jesionowego modyfikowanego termicznie zawierała się w przedziale od 33,5 μm...
-
Granulometric analysis of dry sawdust from the sawing process on the frame sawing machine PRW15M = Granulometrická analýza suchej piliny z procesu pílenia borovicového dreva na rámovej píle PRW-15M
PublicationW artykule przedstawiono wyniki analizy granulometrycznej trocin otrzymanych podczas procesu przecinania drewna sosnowego na pilarce ramowej PRW15M. Wielkość otrzymanych trocin miesciła się w zakresie od 84,7 µm do 15,2 mm. Z punktu widzenia kształtu trociny średniej wielkości d>125µm są swym kształtem zbliżone do włókien drzewnych. Z kolei, drobne frakcje d<125µm mają kształt sześcienny. Ponadto, wzrost prędkości posuwu powoduje...
-
Influence of drying mode and feed per tooth rate on the fine dust creation in pine and beech sawing on a mini sash gang saw
PublicationThe experimental results of the study focused on the effect of drying processes of modified air drying and warm air steam mixture drying of pine and beech wood on the size of sawdust particles created in cutting using PRW-15M sash gang saw, are presented in the paper. Particle size analysis of dry sawdust was performed using two methods—sieving method and laser diffraction analysis. The results showed that the drying process did...
-
The effect of full-cell impregnation of pine wood (Pinus Sylvestris L.) on the fine dust content during sawing on a frame sawing machine
PublicationIn this paper the results of the analysis of the effect of the impregnation treatment of pine wood on the granularity of sawdust from the sawing process on the frame sawing machine PRW 15M are presented. Granulometric analyses of chips from impregnated and unimpregnated pine wood implies that the impregnation of pine wood does not affect the size and structure of the sawdust produced. A major ≈ 95% share of the formed chips is...
-
The role of additives in improving the flammability and calorific value of leather shavings and the binding of chromium compounds in ash
PublicationLeather processing companies are struggling with the problem of increasing costs of post-production waste disposal. Therefore, the issue of thermal waste disposal at the plant and the use of generated heat in the production process is becoming more and more popular. Leather waste on its own does not allow for autothermal combustion despite the sufficient higher heating value (HHV). Therefore the Authors proposed to improve the...
-
Liquefaction of alder wood as the source of renewable and sustainable polyols for preparation of polyurethane resins
PublicationLiquefaction of wood-based biomass gives different polyol properties depending on the reagents used. In this article, alder wood sawdust was liquefied with glycerol and poly(ethylene glycol) solvents. Liquefaction reactions were carried out at temperatures of 120, 150 and 170 °C. The obtained bio-polyols were analyzed in order to establish the process efficiency, hydroxyl number, acid value, viscosity and structural characteristics...
-
Particulate Matter Production of Small Heat Source Depending on the Bark Content in Wood Pellets
PublicationWood pellets as biofuel are more and more used in small heat sources in Europe. Standard wood pellets are produced from wood sawdust without bark. The paper deals about the impact of bark in wood pellets on their properties and combustion process. Special attention in this work is paid to production of particulate matter during combustion of wood pellets depending on bark content. There were experimentally produced spruce wood...
-
Pre-Treatment of Furniture Waste for Smokeless Charcoal Production
PublicationThe aim of this study was to assess the possibility of using furniture waste for smokeless fuel production using the pyrolysis process. Four types of wood-based wastes were used in the pyrolysis process: pine sawdust (PS), chipboard (CB), medium-density fiberboard (MDF), and oriented strand board (OSB). Additionally, the slow and fast types of pyrolysis were compared, where the heating rates were 15 C/min and 100 C/min, respectively....
-
Economical wood sawing with circular saw blades of a new design (Ekonomicno piljenje drva kruznom pilom novog dezajna)
PublicationMaterial-saving and energy-saving belong to the basic requirements imposed on contemporary manufacturing processes. The realization of these processes gives measurable profi ts, not only economical butalso ecological. In the case of wood sawing with circular saw blades, material- and energy-savings are dependent on total overall set of teeth (theoretical kerf) and teeth position accuracy in relation to the workpiece. Hence, it...
-
Removal of diphenols using pine biochar. Kinetics, equilibrium, thermodynamics, and mechanism of uptake
PublicationThermal pyrolysis synthesized activated biochar from the Pinus elliottii sawdust (PS) at 600° C. The obtained activated biochar (PB600) was used for the removal of three diphenols, catechol (CAT), resorcinol (RES), and hydroquinone (HYD), which are utilized mainly in different industries. The PB600 was characterized by several analytical techniques. The BET surface area of 1473 m2.g−1 and a total pore volume of 0.707 cm3 g−1 was...
-
Effect of Thermal Treatment of Birch Wood by Saturated Water Vapor on Granulometric Composition of Chips from Sawing and Milling Processes from the Point of View of Its Processing to Composites
PublicationThe goal of this work is to investigate the impact of thermal modification of birch wood with saturated steam on the particle size distribution of the sawing and milling process. Birch wood (Betula pendula Roth) is an excellent source to produce plywood boards. Wastes from mechanical processing of birch wood are suitable to produce composite materials. Granulometric analyses of chips from sawing processes on the PRW 15M frame saw,...