Wyszukiwarka
Katedra Metrologii i Optoelektroniki
Publikacje
Filtry
wszystkich: 772
Katalog Publikacji
Rok 2015
-
Use of optical skin phantoms for preclinical evaluation of laser efficiency for skin lesion therapy
PublikacjaSkin lesions are commonly treated using laser heating. However, the introduction of new devices into clinical practice requires evaluation of their performance. This study presents the application of optical phantoms for assessment of a newly developed 975-nm pulsed diode laser system for dermatological purposes. Such phantoms closely mimic the absorption and scattering of real human skin (although not precisely in relation to...
-
Waves in a short cable at low frequencies, or just hand-waving? What does physics say? (Invited paper)
PublikacjaWe address the question of low-frequency signals in a short cable, which are often considered as waves in engineering calculations. Such an assumption violates several laws of physics, but exact calculations can be carried out via linear network theory.
-
Zastosowanie Komputerów w Nauce i Technice 2015 XXV cykl seminariów zorganizowany przez PTETiS, Oddział w Gdańsku
PublikacjaZaproponowano zastosowanie termografii skokowej (badania nieniszczące) do indywidualnej oceny jakości warystorów. Dla 20 warystorów niskonapięciowych przeprowadzono badania, w ramach których wykonano pomiary parametrów elektrycznych i termicznych przed testami narażeniowymi i po 2 kolejnych cyklach narażeń (dwa poziomy). Testy narażeniowe zastosowano w celu pogorszenia jakości badanych warystorów. Porównano zasady klasyfikacji...
Rok 2014
-
Algorytmy przetwarzania widm Ramana w procesie detekcji substancji chemicznych
PublikacjaRozprawa przedstawia szczegółowo algorytmy, jakie są stosowane podczas przetwarzania widm Ramana, rejestrowanych przenośnym spektrometrem o skończonej rozdzielczości. Pracę podzielono na osiem rozdziałów. W pierwszym określono cel i tezy pracy. Rozdział drugi opisuje podstawowe pojęcia dotyczące zjawiska Ramana oraz zasady budowy urządzeń do pomiarów widm Ramana. W rozdziale trzecim scharakteryzowano błędy występujące podczas pomiarów...
-
Anatomy of noise in quantitative biological Raman spectroscopy
PublikacjaRaman spectroscopy is a fundamental form of molecular spectroscopy that is widely used to investigate structures and properties of molecules using their vibrational transitions. It relies on inelastic scattering of monochromatic laser light irradiating the specimen. After appropriate filtering the scattered light is dispersed onto a detector to determine the shift from the excitation wavelength, which appears in the form of...
-
AUTOMATED SYSTEM FOR FLUCTUATION ENHANCED GAS SENSING
PublikacjaResistance gas sensors exhibit random phenomena (resistance noise) which can be utilized to improve gas sensitivity and selectivity. That new emerging technique has to be investigated to recognize optimal parameters for gas detection. It means that a measurement system has to have ability of numerous parameters adjustment (e.g., sampling frequency, heater voltage, polarization current, voltage noise amplification). That fact induced...
-
Autonomiczny sterownik systemu pomiarowego na bazie sieci komputerowej
PublikacjaWspółpraca wielu urządzeń pomiarowych czy długotrwała akwizycja danych napotyka problemy: brak jednolitego interfejsu umożliwiającego użytkownikowi proste zarządzanie zbieraniem danych i przejrzystą ekspozycję danych, zużycie energii komputera nadzorującego ciągłą pracę sieci przyrządów pomiarowych. Rozwiązaniem może być zastosowanie autonomicznego kontrolera procesu akwizycji danych umożliwiającego konfigurację parametrów pracy...
-
Błędy w przedstawianiu wyników pomiarów i wartości wielkości fizycznych popełniane w pracach studenckich
PublikacjaArtykuł powstał na bazie doświadczeń zdobytych podczas pracy dydaktycznej autora jako wykładowcy i nauczyciela akademickiego prowadzącego zajęcia w Laboratorium Podstaw Metrologii. Przytoczono przykłady nieprawidłowości w przedsta-wianiu wyników pomiarów i wartości wielkości fizycznych pochodzące z prac pisemnych studentów i skonfrontowano je z zaleceniami Międzynarodowego Układu Jednostek Miar (SI), oraz polskimi aktami prawnymi.
-
Characterization of Optical and Electrical Properties of Transparent Conductive Boron-Doped Diamond thin Films Grown on Fused Silica
PublikacjaA conductive boron-doped diamond (BDD) grown on a fused silica/quartz has been investigated. Diamond thin films were deposited by the microwave plasma enhanced chemical vapor deposition (MW PECVD). The main parameters of the BDD synthesis, i.e. the methane admixture and the substrate temperature were investigated in detail. Preliminary studies of optical properties were performed to qualify an optimal CVD synthesis and film parameters...
-
Comment on "Quantitative comparison of analysis methods for spectroscopic optical coherence tomography"
PublikacjaIn a recent paper by Bosschaart et al. [Biomed. Opt. Express 4, 2570 (2013)] various algorithms of time-frequency signal analysis have been tested for their performance in blood analysis with spectroscopic optical coherence tomography sOCT). The measurement of hemoglobin concentration and oxygen saturation based on blood absorption spectra have been considered. Short time Fourier transform (STFT) was found as the best method for...
-
Demonstrator testera wbudowanego BIST dla układów w pełni różnicowych
PublikacjaPrzedstawiono demonstrator testera wbudowanego, przeznaczony do pracy na stanowisku dydaktycznym w laboratorium z przedmiotu Zaawansowane Metody Pomiarowe i Diagnostyczne. Na stanowisku studenci zapoznają się z technologią BIST (ang. Built-In Self-Test), która jest przykładem wdrożenia strategii projektowania dla testowania.
-
Detection of Denatonium Benzoate (Bitrex) Remnants in Noncommercial Alcoholic Beverages by Raman Spectroscopy
PublikacjaIllegal alcoholic beverages are often introduced into market using cheap technical alcohol, which is contaminated by denatonium benzoate (Bitrex) of very small concentration. Bitrex is the most bitter chemical compound and has to be removed before alcohol consumption. The home-made methods utilize sodium hypochlorite to disintegrate particles of denatonium benzoate in alcohol and to remove bitter taste before trading. In this experimental...
-
Determination of refractive index dispersion using fiber-optic low-coherence Fabry–Perot interferometer: implementation and validation
PublikacjaWe present the implementation and validation of low-coherence Fabry–Perot interferometer for refractive index dispersion measurements of liquids. A measurement system has been created with the use of four superluminescent diodes with different optical parameters, a fiber-optic coupler and an optical spectrum analyzer. The Fabry–Perot interferometer cavity has been formed by the fiber-optic end and mirror surfaces mounted on a micromechanical...
-
Diagnostyka analogowych filtrów wielosekcyjnych oparta na klasyfikato-rach neuronowych z dwucentrowymi funkcjami bazowymi
PublikacjaPrzedmiotem artykułu jest zastosowanie klasyfikatora z dwucentrowymi funkcjami bazowymi do lokalizacji uszkodzeń w wielosekcyjnych torach analogowych elektronicznych systemów wbudowanych sterowanych mikrokontrolerem. Przedstawiono szczegóły procedury pomiarowej oraz metody detekcji i lokalizacji uszkodzeń toru analogowego z wykorzysta-niem klasyfikatora DB zaimplementowanego w postaci algorytmicznej w kodzie programu mikrokontrolera....
-
Diagnostyka analogowych filtrów wielosekcyjnych oparta na magistrali testującej IEEE1149.1
PublikacjaPrzedstawiono nową koncepcję testera JTAG BIST do samo-testowania torów analogowych opartych na wielosekcyjnych filtrach wyższego rzędu w mieszanych sygnałowo mikrosystemach elektronicznych sterowanych mikrokontrolerami i wyposażonych w magistralę testującą IEEE1149.1 (JTAG). Bazuje ona na metodzie diagnostycznej opartej na przekształce-niu transformującym próbki odpowiedzi czasowych kolejnych sekcji filtra pobudzonego impulsem...
-
Direct amination of boron-doped diamond by plasma polymerized allylamine film
PublikacjaA novel microwave pulsed-plasma based method for the modification of the hydrogen-terminated polycrystalline boron-doped diamond (BDD) with a thin film of polymerized allylamine (PPAAm) is reported. A modified BDD surface is resistant to hydrolysis and delamination and is characterized by a high density of positively charged amino groups. Pulsed microwave plasma was applied to improve the degree of cross-linking and bonding of...
-
Distributed wireless sensor for measuring humidity and temperature
PublikacjaHumidity and temperature monitoring is often required in industrial halls and laboratories and can be crucial, because many properties of electrical devices deteriorates under influence of these parameters. There are several useful commercial methods for measuring humidity and temperature, such as commercial hygrometers and humidity recorders. However, they do not allow data acquisition simultaneously from multiple sensors. This...
-
Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a Tool for Analyzing Surface Oxidation Processes on Boron-Doped Diamond Electrodes
PublikacjaSurface oxidation processes play a key role in understanding electrochemical properties of boron-doped diamond (BDD) electrodes. The type of surface termination groups, which create the potential window of electrolytic water stability or hydrophobicity, influences such properties. In this study the kinetics of oxidation process under anodic polarization were studied in situ by means of Dynamic Electrochemical Impedance Spectroscopy...
-
Efficiency of gas mixtures detection by resistive gas sensors
PublikacjaResistive gas sensors are very popular and are commonly used to detect various gases and their mixtures. Theeir main disadvantage is very limited selectivity. Practical use of gas sensors in environenmental applications requires determination of concentration of a few mixed gases at the same time. We would like to present recent results of gas detection improvement by utilizing a single gas sensor and additional measurements to...
-
EFFICIENCY OF GAS MIXTURES DETECTION BY RESISTIVE GAS SENSORS
PublikacjaResistive gas sensors are very popular and are commonly used to detect various gases and their mixtures. Their main disadvantage is very limited selectivity. Practical use of gas sensors in environmental applications (e.g., in sewage systems to protect workers, in air conditioning systems to monitor atmosphere quality) requires determination of concentration of a few mixed gases at the same time. We would like to present recent...
-
Energooszczędny kontroler systemu pomiarowego na bazie sieci Ethernet
PublikacjaWspółpraca wielu urządzeń pomiarowych czy długotrwała akwizycja danych napotyka problemy: brak jednolitego interfejsu umożliwiającego użytkownikowi proste zarządzanie zbieraniem danych i przejrzystą ekspozycję danych, zużycie energii komputera nadzorującego ciągłą pracę sieci przyrządów pomiarowych. Rozwiązaniem może być zastosowanie autonomicznego kontrolera procesu akwizycji danych umożliwiającego konfigurację parametrów pracy...
-
Fluctuation enhanced gas sensing using UV irradiated Au-nanoparticle-decorated WO3-nanowire films
PublikacjaWO3 nanowires (WO3-NWs) decorated with gold nanoparticles (AuNPs) were utilized in resistive gas sensor devices to detect ethanol by use of fluctuation enhanced sensing (FES). The experimental system records both DC resistance and fluctuations of the sensing film. Our data verify that the sensitivity and selectivity of the gas sensor are improved by applying FES when the sensor is stimulated with a combination of UV light and heating....
-
High-Speed Serial Embedded Deterministic Test for System-on-Chip Designs
PublikacjaThe paper presents a high-speed serial interface between external tester and Embedded Deterministic Test (EDT) compression logic hosted by SoC designs. With only a single bidirectional link, the system is capable of feeding distributed heterogeneous cores with hundreds of test channels. Moreover, it synergistically supports EDT bandwidth management to improve the overall test performance. A detailed study indicates a high potential...
-
Image projection in Immersive 3D Visualization Laboratory
PublikacjaIn recent years, many centers in the world attempted to build a virtual reality laboratory. The main idea of such laboratory is to allow the user to “immerse” into and move in a computer-generated virtual world. In the paper, the underlying principles of the system of virtual reality (VR) are described. The selected implementations constructed by the research centers of the world are also presented. The cave automatic virtual environment...
-
Innovative Solutions for Immersive 3D Visualization Laboratory
PublikacjaThe paper presents results of the work concerning the technical specification of Immersive 3D Visualization Laboratory to be opened in late summer 2014 at the Faculty of Electronics, Telecommunications and Informatics at Gdańsk University of Technology in Poland. The person immersed in VR space will be placed in a transparent sphere with a diameter of over 10 feet, supported on rollers and equipped with a motion tracking system....
-
Investigation of RTS Noise in Reverse Polarized Silicon Carbide Schottky Diodes
PublikacjaOne of the method of electronic device quality and reliability evaluation is observation of its inherent noise. The RTS phenomena usually indicates the presence of large defects in the structure of the material of the device, therefore it can be treated as an indicator of technology quality. In the paper authors present results of RTS investigations in reverse polarized Silicon Carbide Schottky diodes. Devices being studied are...
-
Launch of the Immersive 3D Visualization Laboratory
PublikacjaThe paper presents the concept of Immersive 3D Visualization Laboratory, formed at the Faculty of Electronics, Telecommunications and Informatics at Gdańsk University of Technology under the project Gdańsk University of Technology's Modern auditoriums. The basic unit of this laboratory will be cubic CAVE (Cave Automatic Virtual Environment) enriched with spherical walk simulator. This device will allow the user unlimited walking,...
-
Local impedance imaging of boron-doped polycrystalline diamond thin films
PublikacjaLocal impedance imaging (LII) was used to visualise surficial deviations of AC impedances in polycrystalline boron-doped diamond (BDD). The BDD thin film electrodes were deposited onto the highly doped silicon substrates via microwave plasma-enhanced CVD. The studied boron dopant concentrations, controlled by the [B]/[C] ratio in plasma, ranged from 1 × 1016 to 2 × 1021 atoms cm−3. The BDD films displayed microcrystalline structure,...
-
New approaches for improving selectivity and sensitivity of resistive gas sensors: A review
PublikacjaResistive gas sensors are very popular and reliable but suffer from low selectivity and sensitivity. Various methods have been suggested to improve both features without increasing the number of sensors in gas detection systems. Fluctuation enhanced gas sensing was proposed to improve gas detection efficiency by analyzing low-frequency resistance fluctuations, and noise parameters can be more informative than the single DC resistance...
-
Novel approach to modeling spectral-domain optical coherence tomography with Monte Carlo method
PublikacjaNumerical modeling Optical Coherence Tomography (OCT) systems is needed for optical setup optimization, development of new signal processing methods and assessment of impact of different physical phenomena inside the sample on OCT signal. The Monte Carlo method has been often used for modeling Optical Coherence Tomography, as it is a well established tool for simulating light propagation in scattering media. However, in this method...
-
Novel Functionalization of Boron-Doped Diamond by Microwave Pulsed-Plasma Polymerized Allylamine Film
PublikacjaWe report the novel modification of a hydrogen-terminated polycrystalline boron-doped electrode with a microwave pulsed-plasma polymerized allylamine. Boron-doped diamond (BDD) was coated with a very thin layer of adherent cross-linked, pinhole- and additive-free allylamine plasma polymer (PPAAm) resistant to hydrolysis and delamination and characterized by a high density of positively charged amino groups. The pulsed microwave...
-
Optical and structural properties of polycrystalline CVD diamond films grown on fused silica optical fibres pre-treated by high-power sonication seeding
PublikacjaIn this paper, the growth of polycrystalline chemical vapour deposition (CVD) diamond thin films on fused silica optical fibres has been investigated. The research results show that the effective substrate seeding process can lower defect nucleation, and it simultaneously increases surface encapsulation. However, the growth process on glass requires high seeding density. The effects of suspension type and ultrasonic power were...
-
Optical properties of boron-doped nanocrystalline diamond films studied by spectroscopic ellipsometry
PublikacjaThe optical properties of boron-doped nanocrystalline diamond films, coated using Microwave Plasma Enhanced Chemical Vapour Deposition (μPE CVD) system, were analyzed by spectroscopic ellipsometry. Diamond films were deposited on silicon substrates. The ellipsometry data (refractive index (n(λ)), extinction coefficient (k(λ)) were modeled using dedicated software. Evolution of the optical structure with boron doping was observed...
-
Parallel multithread computing for spectroscopic analysis in optical coherence tomography
PublikacjaSpectroscopic Optical Coherence Tomography (SOCT) is an extension of Optical Coherence Tomography (OCT). It allows gathering spectroscopic information from individual scattering points inside the sample. It is based on time-frequency analysis of interferometric signals. Such analysis requires calculating hundreds of Fourier transforms while performing a single A-scan. Additionally, further processing of acquired spectroscopic information...
-
Performance Analysis of the "Intelligent" Kirchhoff- Law - Johnson-Noise Secure Key Exchange
PublikacjaThe Kirchhoff-law - Johnson-noise (KLJN) secure key distribution system provides a way of exchanging theoretically secure keys by measuring random voltage and current through the wire connecting two different resistors at Alice’s and Bob’s ends. Recently new advanced protocols for the KLJN method have been proposed with enhanced performance. In this paper, we analyze the KLJN system and compare with the „intelligent” KLJN (iKLJN)...
-
Polarization-sensitive optical coherence tomography for ceramic materials inspection
PublikacjaCeramics production is looking for a fast, reliable and non-destructive method that can be implemented on site for defect detection and analysis. In this paper we present polarization-sensitive optical coherence tomography (PS-OCT) as a method for defect inspection. Proposed extensions to standard OCT provide additional information for complete characterization of tested object. We compare OCT and microscope imaging that can easily...
-
Przemysłowe zastosowania optycznej tomografii koherentnej
PublikacjaOptyczna tomografia koherentna (OCT) jest nowoczesną techniką obrazowania wewnętrznej struktury obiektów rozpraszających światło. Główne zastosowania OCT należą do dziedziny obrazowania medycznego, jednak prowadzony jest także szereg badań nad przemysłowymi aplikacjami tej metody. Zaletą OCT jest możliwość tomograficznego obrazowania z rozdzielczością rzędu pojedynczych mikrometrów w sposób szybki i nieinwazyjny. W niniejszym artykule...
-
Quality assessment of ZnO-based varistors by 1/f noise
PublikacjaNoise has been used as a diagnostic tool of surge arrester varistor structures comprising of ZnO grains of various type and size. The physical and electrical properties of the measured samples have been described. In the experimental study, the applied measurement system and the results of noise measurements for the selected structures of varistors designed for the continuous working voltage 280 V, 440 V and 660 V have been presented....
-
Response of a New Low-Coherence Fabry-Perot Sensor to Hematocrit Levels in Human Blood
PublikacjaIn this paper, a low-coherence Fabry-Perot sensor with a spectrally measured signal processing response to the refractive index of liquids is presented. Optical fiber sensors are potentially capable of continuous measuring hematocrit levels in blood. Low-coherence Fabry-Perot interferometric sensors offer a robust solution, where information about the measurand is encoded in the full spectrum of light reflected from the sensing...
-
Samotestowanie toru analogowego ze wzmacniaczem w pełni różnicowym w elektronicznych systemach wbudowanych sterowanych mikrokontrole-rami
PublikacjaPrzedstawiono nową metodę samotestowania toru analogowego opartego na wzmacniaczu w pełni różnicowym w elektronicznych systemach wbu-dowanych sterowanych mikrokontrolerami. Bazuje ona na nowej metodzie diagnostycznej opartej na przekształceniu transformującym próbki odpo-wiedzi czasowej badanej części analogowej na pobudzenie "ujemnym" impulsem prostokątnym na wejściu Vocm na krzywe identyfikacyjne w przestrzeni pomiarowej. Metoda...
-
SAMPLE-AND-HOLDING METHOD FOR GAS SENSING APPLIED FOR RESISTANCE GAS SENSORS
PublikacjaThe DC resistance of a Taguchi gas sensor is influenced by the ambient gas. To improve the selectivity and sensitivity of a sensor the fluctuation enhanced sensing (FES) was used. The paper proposes a novel methodology of utilizing FES technique that sample composition of an ambient atmosphere and hold it for further processing (sample-and-holding technique). The method uses the heated gas sensor to sample an ambient atmosphere...
-
Supercapacitors - charge redistribution and restoring voltage
PublikacjaThe charge in supercapacitor is stored on electrodes and in electrolyte. The charges on electrodes create the Helmholtz double layer which is formed immediately with time constant of the order of seconds, while the charge storage in electrolyte is going on with time constant of the order of hundreds seconds. When the charged supercapacitor is shorted for few seconds, the charge from electrodes is discharged while the charge in...
-
Szumy czujników : Metody pomiarów i analizy
PublikacjaW pracy przedstawiono problematykę pomiarów i analizy szumów w wybranych rodzajach czujników. Przedstawiono mechanizmy powstawania szumów, metody ich pomiarów oraz analizy. W pracy występuje szereg przykładów w których szumy są źródłem informacji o zjawiskach zachodzących w otoczeniu czujnika. Praca będzie przydatna dla osób zajmujących się problematyką pomiarów i analizy sygnałow o niewielkiej intensywności.
-
Termowizja jako narzędzie weryfikacji stanu elementów ochronnych SMD podczas badań udarowych
PublikacjaPrzedstawiono wyniki badań przyrostów temperatury rejestrowanych za pomocą kamery termowizyjnej ochronnych elementów SMD podczas wykonywania badań odporności na udary napięciowe wykonywane wg normy EN61000-4-5 dla różnych poziomów sprzężeń impedancyjnych
-
Thickness and structure change of titanium (IV) oxide thin films synthesized by the sol–gel spin coating method
PublikacjaTitanium dioxide is a well-known material in nanotechnology, while it provides new opportunities due to its interesting properties, for example, as a semiconductor with a quite significant forbidden band gap energy of 3.2 eV. In this study, thin films of titanium dioxide (TiO2) were synthesized in amorphous and crystallographic systems using the sol–gel process. Atomic Force Microscopy (AFM), Raman spectroscopy and X-ray diffraction...
-
Thin CVD diamond films - synthesis, properties, applications
PublikacjaThe basic model of diamond films growth, in the low pressure synthesis, deposition from the CVD gas phase, is the mixture of hydrocarbon gas in presence with activated hydrogen and its nucleation on the substrate as a result of pyrolysis reaction. It allows to cross the great energetic barrier between graphite and diamond. High pressure and temperature are replaced by change of electronic structure of atoms into gas precursors...
-
Time-frequency analysis in optical coherence tomography for technical objects examination
PublikacjaOptical coherence tomography (OCT) is one of the most advanced optical measurement techniques for complex structure visualization. The advantages of OCT have been used for surface and subsurface defect detection in composite materials, polymers, ceramics, non-metallic protective coatings, and many more. Our research activity has been focused on timefrequency spectroscopic analysis in OCT. It is based on time resolved spectral analysis...
-
Two‐functional μBIST for Testing and Self‐Diagnosis of Analog Circuits in Electronic Embedded Systems
PublikacjaThe paper concerns the testing of analog circuits and blocks in mixed‐signal Electronic Embedded Systems (EESs), using the Built‐in Self‐Test (BIST) technique. An integrated, two‐functional, embedded microtester (μBIST) based on reuse of signal blocks already present in an EES, such as microprocessors, memories, ADCs, DACs, is presented. The novelty of the μBIST solution is its extended functionality. It can perform 2 testing functions:...
-
Układy zasilania energią resztkową z urządzeń grzewczych
PublikacjaPozyskiwanie energii resztkowej z różnorodnych źródeł ma za zadanie odzyskanie energii z nietypowych źródeł takich jak np.: drgania, ruch mas powietrza, efekt termiczny. Energia pozyskiwana z tych niekonwencjonalnych źródeł jest obecnie wykorzystywana do zasilania sieci sensorowych, czy mikrokontrolerów o niskich poborach mocy. Stosowanie technologii pozyskiwania energii resztkowej pozwala wyeliminować konieczność doprowadzania...
-
Uruchomienie Laboratorium Zanurzonej Wizualizacji Przestrzennej
PublikacjaArtykuł przedstawia koncepcję Laboratorium Zanurzonej Wizualizacji Przestrzennej (ang. Immersive 3D Visualization Laboratory), powstającego właśnie przy Wydziale Elektroniki, Telekomunikacji i Informatyki (ang. Faculty of Electronics, Telecommunications and Informatics) Politechniki Gdańskiej (ang. Gdańsk University of Technology) w ramach grantu Nowoczesne Audytoria Politechniki Gdańskiej (ang. project Gdansk University of Technology’s...