Wyszukiwarka
Wydział Inżynierii Mechanicznej i Okrętownictwa
Publikacje
Filtry
wszystkich: 2551
wyświetlamy 1000 najlepszych wyników Pomoc
Katalog Publikacji
Rok 2022
-
PORÓWNANIE DZIAŁANIA POPRZECZNYCH ŁOŻYSK ŚLIZGOWYCH NA ZMODERNIZOWANYM STANOWISKU DYDAKTYCZNYM
PublikacjaW artykule przedstawiono autorską metodę porównania działania poprzecznych łożysk ślizgowych na podstawie wyników badań wykonanych na zmodernizowanym stanowisku laboratoryjnym. Modernizacja stanowiska składającego się ze źródła mocy w postaci silnika elektrycznego napędzającego dwa wały połączone sprzęgłem i zakończone łożyskiem wzdłużnym przekazującym siłę naporu. Podłączenie przetwornika częstotliwości umożliwiło pracę silnika...
-
Prediction of Weld Deformations by Numerical Methods - Review
PublikacjaThe welding process is the basic technique of joining in the shipbuilding industry. This method generates welding distortions that cause a lot of problems during the manufacturing process due to both the time and cost of straightening as well as their influence on later stages of production. Proper preparation of welding processes plays a growing role in the shipbuilding industry and the development of calculating tools is being...
-
Preliminary studies on the effect of feed speed on the colour change of wood
PublikacjaThis paper presents the results of preliminary analyses of the effect of cutting parameters on changes in the colour of wood. Beech wood cut with use circular saw was analysed. The cutting parameter tested was the feed speed, represented by the feed per tooth. Sawing processes with different feed per tooth ranging from 0.0008 mm to 0.09 mm were analysed. It was observed that over the entire range of feed rate per tooth analysed,...
-
Probing Local Structural Changes by Sharp Luminescent Infrared Nanophosphor for Application in Light-Emitting Diodes
PublikacjaCr3+-doped infrared phosphors are promising candidates for next-generation phosphor-converted infrared light-emitting diodes (LEDs) because they can, in principle, tune and convert the luminescence spectra from an LED chip. However, most studies focus on broad-band Cr3+-doped phosphors, and the control mechanism of Cr3+-doped phosphors with sharp line emissions remains ambiguous. Here, we report LiGa5(1–x)Al5xO8:Cr3+ phosphors...
-
Problems associated with the up of actuating system of a single-disc lapping machine for flat surfaces
PublikacjaPrzedstawiono wyniki badań nagrzewania się podstawowych elementów układu wykonawczego docierarki jednotarczowej o standardowej kinematyce do obróbki powierzchni płaskich. Analizowano przyrost temperatury zespołu napędowego, rolek i pierścieni prowadzących separatory oraz tarczy docierającej i obrabianych elementów. Badano nagrzewanie się układu obróbkowego podczas wyrównywania żeliwnego narzędzia i docierania powierzchni płaskich....
-
Production and Properties of the Porous Layer Obtained by the Electrochemical Method on the Surface of Austenitic Steel
Publikacja: The growing demand for implants has seen increasing interest in the introduction of new technologies and surface modification methods of metal biomaterials. This research aimed to produce and characterize a porous layer grown on austenitic stainless steel 316L, obtained via the anodization process near the micro-arc oxidation, i.e., low voltage micro-arc oxidation (LVMAO). The discussed layer significantly influences the properties...
-
Properties of New Composite Materials Based on Hydroxyapatite Ceramic and Cross-Linked Gelatin for Biomedical Applications
PublikacjaThe main aim of the research was to develop a new biocompatible and injectable composite with the potential for application as a bone-to-implant bonding material or as a bone substitute. A composite based on hydroxyapatite, gelatin, and two various types of commercially available transglutaminase (TgBDF/TgSNF), as a cross-linking agent, was proposed. To evaluate the impacts of composite content and processing parameters on various...
-
Przegląd metod wytwarzania energii elektrycznej z wodoru i ocena potencjału ich zastosowania w krajowym systemie elektroenergetycznym
PublikacjaW artykule dokonano przeglądu dostępnych metod wytwarzania energii elektrycznej z udziałem technologii wodorowych i podjęto próbę oceny potencjału ich zastosowania w polskim systemie elektroenergetycznym. Szczególną uwagę poświęcono ogniwom paliwowym, omawiając dostępne na rynku typy ogniw oraz ich podstawowe parametry techniczne. W zakresie technologii wodorowych, rozważono możliwość samodzielnej pracy ogniw paliwowych, turbin...
-
Quasi-Static Response
PublikacjaConcern for the quasi-static response of ship and offshore structures, as required for safety and serviceability assessments. Attention shall be given to uncertainty quantification of quasi-static load and response analysis approaches, and their limitations, including exact and approximate methods for derivation of different acceptance criteria.
-
Reliability of acicular grindable thermocouples for transient temperature measurements at sliding contacts
PublikacjaAcicular grindable thermocouples represent an interesting and prospective technique of temperature measurements at sliding contacts. This study aimed at the investigation of their reliability and accuracy as applied to the friction materials of various classes in contact with steel. The tests were conducted on a pin-on-disc tribometer under stationary and transient regimes. The experimental results were validated by comparing the...
-
Research on Linear Actuators for Active Foil Bearings
PublikacjaActive foil bearings are a kind of gas foil bearing. They contain actuators which allow for modification of the bearing sleeve size and the shape of the lubrication gap. Rotor vibrations can be actively controlled by these changes. It is possible, among other things, to reduce the starting torque, control the vibration amplitude at different speeds and improve operational safety. Prototypes of active foil bearings are being developed...
-
Rheology of Variable Viscosity‐Based Mixed Convective Inclined Magnetized Cross Nanofluid with Varying Thermal Conductivity
PublikacjaCross nanofluid possesses an extraordinary quality among the various fluidic models to explore the key characteristics of flowing fluid during very low and very high shear rates and its viscosity models depend upon shear rate. The current study establishes the numerical treatment regarding variable viscosity‐based mixed convective inclined magnetized Cross nanofluid with var‐ ying thermal conductivities over the moving permeable...
-
Simulation of hybridized nanofluids flowing and heat transfer enhancement via 3-D vertical heated plate using finite element technique
PublikacjaThe present study probed the creation of heat energy and concentrating into Newtonian liquids across vertical 3D-heated plates. The role of the Soret and Dufour theories in concentrating and energy formulas is discussed. The role of hybrid nanoparticles is introduced to illustrate particle efciency in terms of solute and thermal energy. It is removed a viscous dissipation process and a changing magnetic feld. The proposed approach...
-
Slowly-closing valve behaviour during steam machine accelerated start-up
PublikacjaThe paper discusses the state of stress in a slowly-closing valve during accelerated start-up of a steam turbine. The valve is one of the first components affected by high temperature gradients and is a key element on which the power, efficiency and safety of the steam system depend. The authors calibrated the valve model based on experimental data and then performed extended Thermal-FSI analyses relative to experiment. The issue...
-
Some new soliton solutions to the higher dimensional Burger–Huxley and Shallow water waves equation with couple of integration architectonic
PublikacjaIn this paper, we retrieve some traveling wave, periodic solutions, bell shaped, rational, kink and anti-kink type and Jacobi elliptic functions of Burger’s equation and Shallow water wave equation with the aid of various integration schemes like improved -expansion scheme and Jacobi elliptic function method respectively. We also present our solutions graphically in various dimensions.
-
Stress analysis of suspended rail vehicle bogie
PublikacjaNiniejsza publikacja została poświęcona analizie wytrzymałościowej wybranych elementów wózka – osi zestawu kołowego i ramy. Obliczenia osi wykonano w oparciu o metodę analityczną przy rozpatrzeniu różnych materiałów jej wykonania. Do sprawdzenia wytrzymałości ramy wykorzystano metodę elementów skończonych, a obciążenie wyznaczono zgodnie z wytycznymi normy PN-EN 13749. Sam wózek jest częścią podwieszanego elektrycznego zespołu...
-
Stress–strain model of lower corroded steel plates of normal strength for fitness-for-purpose analyses
PublikacjaThis study investigates the mechanical properties of specimens made of normal strength steel subjected to lower marine immersed corrosion degradation levels (below 25 %). The specimens were corroded in laboratory conditions, and only natural factors were controlled to raise the corrosion rate (reaching the level of 1 mm/year). Three different thicknesses of plates made of normal strength of shipbuilding steel are investigated (between...
-
Struktury oraz mapy przepływu R1233zd w okrągłym minikanale przy średnich i wysokich wartościach ciśnienia zredukowanego [w:] Postępy w badaniach wymiany ciepła i masy
PublikacjaW wiedzy dotyczącej struktur przepływu niskowrzących czynników roboczych w zakresie wysokich temperatur nasycenia (powyżej 120°C) oraz średnich i wysokich wartościach ciśnienia zredukowanego (0.5-0.9) występuje luka. W literaturze obecne są dane dotyczące podobnych wartości ciśnień zredukowanych, ale dla niższych wartości temperatury nasycenia (głównie z zakresu -20°C do 40°C). Wynika to z dotychczasowych zastosowań chłodniczych...
-
Study of the Layer-Type BST Thin Film with X-ray Diffraction and X-ray Photoelectron Spectroscopy
PublikacjaIn the present paper, results of X-ray photoelectron studies of electroceramic thin films of barium strontium titanate, Ba1xSrxTiO3 (BST), composition deposited on stainless-steel substrates are presented. The thin films were prepared by the sol-gel method. A spin-coating deposition of BST layers with different chemical compositions was utilized so the layer-type structure of (0-2) connectivity was formed. After the deposition,...
-
TEMPERATURE INFLUENCE ON TIRE ROLLING RESISTANCE MEASUREMENTS QUALITY
PublikacjaGlobal warming makes it necessary to reduce energy consumption, which in the case of motor vehicles, is connected, among other things, with reduction of resistive forces acting on a vehicle during its motion. One of the most important components of those forces is rolling resistance, which is very difficult to measure, especially in road conditions. The article deals with issues related to the influence of the thermal state of...
-
The effect of beech wood (Fagus sylvatica L.) steaming process on the colour change versus depth of tested wood layer
PublikacjaThe results of experimental research on the colour changes of beech wood at different depths of the tested layer are presented. Beech wood (Fagus sylvatica L.) dried in a conventional kiln was tested. Half of the wood samples were steamed prior to the drying process. Colour changes were measured at various depths after the face milling process was used to remove the material to expose to the deeper surface. The colour changes were...
-
The Effect of Openings’ Size and Location on Selected Dynamical Properties of Typical Wood Frame Walls
PublikacjaThe wooden frame constructions are now popular in many developed countries of the world. Many of these locations where such buildings are constructed are exposed to seismic and other shocks which are generated by human activities. This paper discusses the effect of the size and location of openings in the wooden frame walls under dynamic loadings. Natural frequencies of such frames with and without openings have been determined....
-
The effect of Sr and Mg substitutions on structure, mechanical properties and solubility of fluorapatite ceramics for biomedical applications
PublikacjaIonic substitutions play important role in the modifications of biological apatites. Recently, attention has been focused on the co-doping effects on the functional properties of apatite-based biomaterials. In this research work, the dense samples of fluorapatites, Ca10(PO4)6F2 and Ca8MgSr(PO4)6F2, were produced after sintering at 1250 °C for 6 h in air. Structural characterization carried out with XRD, IR, Raman and SEM, confirmed...
-
The Effects of Pin Profile on HDPE Thermomechanical Phenomena during FSW
PublikacjaFriction stir welding (FSW) of polymeric materials has recently attracted significant attention. Herein, we present the effect of the tool pin profile on the FSW of high-density polyethylene (HDPE) joints through joint experimental analysis and thermomechanical simulations. For analysis of pin profile effects on the thermomechanical properties of HDPE joints, frustum (FPT), cubic (CPT), and triangular (TPT) pin shapes were selected...
-
The energy approach to fatigue crack growth of S355 steel welded specimens subjected to bending
PublikacjaThe study presents the results of the research on the rate of fatigue crack growth subjected to bending in the ferritic-pearlitic structure. The studies were carried out at a constant amplitude of the moment and at various values of the load ratios R and at the operating frequency of the machine of 28.4 Hz. Flat specimens made of S355 steel and with fillet welds and with double-sided blunt external notches as well as concave...
-
The impact of shipping 4.0 on controlling shipping accidents: A systematic literature review
PublikacjaMaritime shipping, with a significant role in global trade, confronts various accidents leading to loss of lives, properties, and the environment. Shipping 4.0 technologies are scaling up to address this problem by employing real-time data-driven technologies, including cyber-physical systems, advanced tracking and tracing, intelligent systems, and big data analytics. Despite growing attention, there is a general lack of clarity...
-
The impact of surface slope and calculation resolution on the fractal dimension for fractures of steels after bending-torsion fatigue
PublikacjaThe article presents the results of the fractal dimension measurements on the fatigue fracture surfaces of 10HNAP and S355J2 steels specimens after combined bending-torsion fatigue. For smooth and ring-notched specimens, three loading conditions were analyzed: (1) bending; (2) bending-torsion; and (3) torsion fatigue. Post-failure surface topography measurements were carried out on the entire fracture surfaces using an optical...
-
The influence of pressure drop on the working volume of a hydraulic motor
PublikacjaReliability and maintenance analysis of hydraulic positive machines basicly focused on the processes of their wear and failure. But in order to correctly assess the mechanical and volumetric efficiency of a hydraulic motor, both at the stage of development research or at the stage of control tests during its exploitation, the working volume of this motor must be correctly determined. Therefore this paper proposes a new method of...
-
The methodology of design of satellite working mechanism of positive displacement machine
PublikacjaIn this paper is described a methodology of design of satellite mechanism consisting of two noncircular gears (externally toothed rotor and internally toothed curvature) and circular gears (satellites). In the presented methodology is assumed that the rotor pitch line is known, and the curvature pitch line is necessary to designate. The presented methodology applies to mechanisms for which the number of the curvature humps is at...
-
The Motion Analysis of Attacus Atlas Rigid Wing
PublikacjaThe remarkable aerodynamic efficiency of flapping insect wings has fascinated researchers for many years. Butterfly wings are distinguished by a much larger lifting surface, and thus, a different style of flapping flight. The considerations described in the article are an introduction to a fully flexible analysis of the wing in motion. The study of the rigid wing gives the basic knowledge necessary in the further process. The yaw,...
-
The potential of computational methods for the categorization of architectural objects on the example of media architecture
PublikacjaThe paper presents an example of the categorization of architectural objects and assessment of the characteristics of urban space, based on the analysis of specific features of architectural objects and urban landscape. The conducted analysis refers to media architecture and is presented in the complex context of the development of media solutions. The field of influence of IT on architecture is also stressed, both on the architect’s...
-
Thermal cooling process by nanofluid flowing near stagnating point of expanding surface under induced magnetism force: A computational case study
PublikacjaThis paper is dedicated to the exam of entropy age and research of the effect of mixing nanosolid additives over an extending sheet. In this review, Newtonian nanofluid version turned into researched at the actuated appealing field, heat radiation and variable heat conductivity results. With becoming modifications, the proven PDEs are moved into popular differential situations and paintings mathematically making use of a specific...
-
Thermal Energy Development in Magnetohydrodynamic Flow Utilizing Titanium Dioxide, Copper Oxide and Aluminum Oxide Nanoparticles: Thermal Dispersion and Heat Generating Formularization
PublikacjaThe main aim of this article heat transfer in thermal engineering deals with the production, use, transformation, and transfer of thermal energy. Engineering and industrial fields including food packaging, the production of food additives, electronic cooling, microturbines, etc. heavily rely on heat transmission. Due to its intriguing potential in industries like the production of polymers, paper, crystal glass, etc., scientists...
-
Thermodynamic, ecological, and economic analysis of negative CO2 emission power plant using gasified sewage sludge
PublikacjaCurrently, sewage sludge is considered as a biomass, according to the Polish act on renewable energy sources from 20th of February 2015 and its novel version from 19th of July 2019. Possibility to utilize sewage sludge in gasification process is an additional advantage of the negative CO2 emissions power plant (nCO2PP). The work presents results of thermodynamic, ecological, and economical analysis using a zero-dimensional mathematical...
-
Three-Dimensional Fractography for Conventional and Additive Manufactured Steels After Bending-Torsion Fatigue
PublikacjaIn this study, fracture surface topography parameters were measured to investigate the effects of multiaxial loading. In order to assess the metrological aspects of fracture for notched specimens made of high-strength steels processed by both conventional and additively manufacturing (AM) techniques, an optical surface profilometer was used. Three bending moment to torsion moment ratios (B/T) were studied, i.e. 2, 1 and 2/3. The...
-
Towards evaluation of the Second Generation Intact Stability Criteria - examination of a fishing vessel vulnerability to surf-riding, based on historical capsizing
PublikacjaThe Second Generation Intact Stability Criteria (SGISC) are the latest achievements in the field of intact ship stability assessment. The criteria are the result of massive international cooperative efforts and extensive research that lasted more than 15 years. Even though they are based on a solid scientific foundation, the trial period has commenced to collect user experience and further validation. One of possible approaches...
-
Uncertainty quantification of modal parameter estimates obtained from subspace identification: An experimental validation on a laboratory test of a large-scale wind turbine blade
PublikacjaThe uncertainty afflicting modal parameter estimates stems from e.g., the finite data length, unknown, or partly measured inputs and the choice of the identification algorithm. Quantification of the related errors with the statistical Delta method is a recent tool, useful in many modern modal analysis applications e.g., damage diagnosis, reliability analysis, model calibration. In this paper, the Delta method-based uncertainty...
-
Underwater Processing of Materials
PublikacjaEditorial do SI
-
Weather Routing System Architecture Using Onboard Data Collection and Route Optimisation
PublikacjaThis paper describes the architecture of a weather routing system consisting of two key elements: onboard monitoring and route optimiser sub-systems. The former is responsible for collecting various onboard measurements, such as current ship position or ship motion variables. These data, when gathered and processed, are then used for fine-tuning a ship model. The model, together with weather forecasts, is utilised by a multi-objective...
-
Whether Carbon Nanotubes Are Capable, Promising, and Safe for Their Application in Nervous System Regeneration. Some Critical Remarks and Research Strategies
PublikacjaCarbon nanotubes are applied in or considered for different fields of medicine. Among them is the regeneration or rebuilding of nervous system components, which still lack substantial progress; this field is supported by carbon nanotubes to a great extent as the principal material. The limited research on this issue has involved PU/silk/MWCNTs, PCL/silk/MWCNTs, PCL/PGS/CNTs, chitin/CNTs, PGF/CNTs, CNTs/PGFs/PLDLA,MWCNTs chitosan,MWCNTs/PPy,...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublikacjaWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
Wpływ parametrów konstrukcyjnych sprzęgieł mokrych i ich sterowania na zmiany wybranych wielkości fizycznych w trakcie zmian przełożenia przekładni mechanicznej
PublikacjaPrzedmiotem rozprawy doktorskiej jest analiza wpływu parametrów konstrukcyjnych i sterowania sprzęgłami ciernymi na zmiany wybranych wielkości fizycznych w trakcie zmiany przełożenia dwubiegowej przekładni mechanicznej typu Powershift. W ramach rozprawy przedstawiono znane rozwiązania skrzyń biegów maszyn roboczych. Szczególną uwagę poświęcono skrzyniom Powershift i stosowanych w nich rozwiązaniach sterowania sprzęgłami. Ponadto...
-
Wpływ warunków zgrzewania metodą Friction Stir Welding na własności mechaniczne i jakość złączy ze stopu aluminium
PublikacjaW prezentacji przedstawiono wyniki badań nad wpływem warunków zgrzewania metodą FSW na jakość połączeń ze stopów aluminium.
-
Wpływ warunków zgrzewania metodą Friction Stir Welding na własności mechaniczne i jakość złączy ze stopu aluminium
PublikacjaCelem niniejszych badań było porównanie wpływu kształtu narzędzia na złącze oraz uzyskanie wartości parametrów zgrzewania tarciowego z przemieszaniem (FSW) zapewniających najlepszą możliwą jakość złącza. Zastosowanym materiałem był stop aluminium EN AW-3004 (AlMn1Mg1). Według najlepszej wiedzy autorów dotychczas nie przedstawiono żadnych badań tego stopu w kwestii zgrzewania FSW. Złącza pięcioczołowe wykonano samodzielnie opracowanym...
-
WYNIKI SYMULACJI NUMERYCZNEJ CYKLU ROBOCZEGO SILNIKA O ZS W PROGRAMIE DIESEL-RK ORAZ OCENA ICH UŻYTECZNOŚCI W PROCESIE PLANOWANIA BADAŃ DIAGNOSTYCZNYCH OKRĘTOWEGO SILNIKA TŁOKOWEGO
PublikacjaW artykule przedstawiono wyniki symulacji numerycznej procesu roboczego realizowanego w silniku tłokowym o zapłonie samoczynnym. W zastosowanym programie użytkowym DIESEL-RK zaimplementowano silnik laboratoryjny Farymann Diesel typ D10. Wprowadzono wybraną niesprawność jego układu funkcjonalnego zasilania paliwem - obniżone ciśnienie otwarcia wtryskiwacza pwtr. Wyznaczono wartości adekwatnych parametrów diagnostycznych: temperaturę...
-
Wyszukiwanie źródła sygnału przy użyciu grupy robotów
PublikacjaW pracy przedstawiono algorytm wyszukiwania źródła sygnału oparty na zmodyfikowanej metodzie wyszukiwania źródła sygnału RSSI. Fizyczna implementacja tego algorytmu opiera się na wykorzystaniu losowo rozłożonych dwukołowych robotów poruszających się w formacji roju. Uzyskane wyniki z badań doświadczalnych wskazują, że proponowana fizyczna implementacja algorytmu w przeprowadzonych próbach pozwoliła na uzyskanie średniej dokładności...
-
Z historii Stowarzyszenia Inżynierów i Techników Polskich w Szwajcarii
PublikacjaPrzedstawiono, pokrótce, historię i działalność Stowarzyszenia Inżynierów i Techników Polskich w Szwajcarii. Wspomniano o związkach polskich naukowców pracujących w szwajcarskich uczelniach, w pierwszych latach powojennych, z Politechniką Gdańską.
-
Z historii Stowarzyszenia Techników i Inżynierów Polskich na Litwie
PublikacjaPrzedstawiono pokrótce historię Stowarzyszenia Techników i Inżynierów Polskich na Litwie. Wskazano na związki STIP z Europejską Federacją Polonijnych Stowarzyszeń Naukowo-Technicznych oraz z FSNT NOT. Scharakteryzowano działalność patrona Stowarzyszenia Techników i Inżynierów na Litwie Rafała Kalinowskiego.
-
Zastosowanie przedmiotowych uchwytów modułowych w operacjach wytwarzania na przykładzie obróbki korpusu.
PublikacjaOmówiono zastosowanie przedmiotowych uchwytów modułowych w operacjach obróbkowych. Przedstawiono dwa warianty technologii korpusu jednolitego. Omówiono konstrukcje wykorzystywanych uchwytów modułowych oraz ich koszt i czasochłonność analizowanych operacji na dwóch centrach obróbkowych, o pionowej i poziomej osi wrzeciona.
-
Zmiennofazowy akumulator ciepła w dolnym źródle pompy ciepła – propozycja dla budynku jednorodzinnego
PublikacjaW artykule przedstawiono autorskie rozwiązanie zmiennofazowego akumulatora ciepła, w którym jawne i utajone ciepło szarych ścieków jest odbierane za pomocą prototypowego wymiennika ciepła posadowionego w akumulatorze i sprzęgniętego z parownikiem pompy ciepła. Ścieki szare dopływają do akumulatora z budynku jednorodzinnego. Układ funkcjonuje w systemie grzewczym tego budynku. Omówiono doświadczenia z dotychczasowej eksploatacji...