Wyszukiwarka
Filtry
wszystkich: 12
wybranych: 9
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: nozzles
-
Design and distribution of air nozzles in the biomass boiler assembly
PublikacjaDue to energy crisis as well as increasing pollution of the environment, renewable energy sources usage increases all over the world. These facts encouraged authors to start research over developing a uniform biomass boiler calculation model. This paper presents a design of biomass boiler assembly created for ORC (Organic Rankine Cycle) unit since these systems could achieve strong position in energy industry....
-
CFD analysis of jet flows ejected from different nozzles
Publikacja -
Structural optimization of microjet array cooling system
PublikacjaThe single phase heat transfer from an upward facing, horizontal copper surface to arrays of impinging water jets was experimentally investigated. Experimental configuration allows for a free-surface unconfined jets flow. Square nozzles 50 × 100 μm arranged in four different geometries were used. Additionally, for the set of two jets array geometry was varied by adjusting the nozzle to nozzle distance. The area averaged heat transfer...
-
Investigations of Aerodynamics of Tesla Bladeless Microturbines
PublikacjaThe paper presents an analysis of a Tesla bladeless turbine for a co-generating micro-power plant of heat capacity 20 kW, whichoperates in an organic Rankine cycle with a low-boiling medium. Numerical calculations of flow in several Tesla turbine models areperformed for a range of design parameters. Results of investigations exhibit interesting features in the distribution of flowparameters within the turbine interdisk space. The...
-
EXPERIMENTAL RESEARCH ON INFLUENCE OF THE FUEL NOZZLE GEOMETRY ON THE FUEL CONSUMPTION OF THE MARINE 4-STROKE DIESEL ENGINE
PublikacjaThe article presents experimental research that has been carried out on a marine, 4-stroke, 3-cylinder, turbocharged engine. During testing, the engine operated at a constant rotational speed of 750 rpm and a load from 0 kW to 280 kW. The engine was fuelled by diesel oil of known specification and loaded by electric generator with water resistance. The fuel consumption was measured during the engine operation with fuel nozzles...
-
ENHANCED EVAPORATION OF THE DROPLETS OF CONDENSATE IN THE ASYMMETRICAL SHOCK WAVE ZONE
PublikacjaIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages [4,5]. The formation and evolution of these droplets lower the performance of the wet stages of the turbines, and their effects on the efficiency are collectively known as wetness losses [4]. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current....
-
Isothermal turbines − New challenges. Numerical and experimental investigations into isothermal expansion in turbine power plants
PublikacjaThe efficiency of power plants with steam or gas turbines depends on the efficiencies of a thermodynamic cycle and devices implementing this cycle. In the case of high power outputs, we cannot expect a significant increase in the efficiency of individual devices. Therefore, what remains is to increase the efficiency of the implemented thermodynamic cycle - the complex Rankine cycle in the case of steam turbines or the extended...
-
Design and investigations of a micro-turbine flow part
Publikacja-generative micro-power plant with the HFE7100 as a working medium was designed and built for experimental investigations. The heat output of the plant was assumed equal to 20 kW, while the electric output amounted to about 3kW.In the paper a multi-stage micro-turbine with partial admission of all the stages is described in detail and the results of the particular experimental investigations and numerical calculations are shown,...
-
Comparison of heat transfer characteristics in surface cooling using microjets with water, ethanol and HFE7100 as test fluids
PublikacjaAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the dimensions of the size of nozzle leads to an increase in the economy of cooling and improves its quality. Present study describes research related to the design and construction of the nozzles and microjet study, which may be applied in many technical applications such as in metallurgy, electronics, etc....