Search
dr inż. Aleksandra Świerczyńska
Employment
- Assistant professor at Institute of Manufacturing and Materials Technology
Publications
Filters
total: 67
Catalog Publications
Year 2024
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublicationUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
Exploring the trends in flux-cored arc welding: scientometric analysis approach
PublicationFlux-cored arc welding (FCAW) is a universal group of welding methods in terms of the scope of application and automation possibilities, the share of which in various industries in many countries is still increasing. The paper presents the results of bibliographic analyses (scientometric analysis with the use of VOSviewer, Bibliometrix and CitNetExplorer tools) of a data set of 993 publications indexed in the Web of Science database...
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublicationThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
Year 2023
-
Determination of t8/5 cooling times for underwater local dry welding of steel
PublicationKnowledge of thermal history is the basic condition for studying the structure - properties of welded joints. The determinant of thermal history is the thermal cycle, whose in-situ measurements are still a big challenge. Water as the welding environment complicates this issue even more. The article presents a method to determine an equation for calculating t8/5 cooling times for underwater gas metal arc welding of unalloyed steels...
-
Effect of Arc Strikes on High Strength Low Alloy Steels Welded by SMAW
PublicationWet welding with covered electrodes (Shielded Metal Arc Welding – SMAW) is the most commonly used method of carrying out welding repair works in a water environment. Limited visibility and the inability to move freely under water result in an increased risk of formation of welding imperfections such as lack of fusion, lack of penetration and arc strikes. The work focused on changes in the properties and structure of steel subjected...
-
Effects of Storing Flux-Cored Wires under Various Conditions
PublicationWelding processes involving the use of flux-cored wires are becoming increasingly popular, particularly in shipbuilding as well as in off-shore and civil engineering. The article presents characteristics of the welding process, its areas of application as well as advantages and disadvantages (e.g. necessity of ensuring appropriate conditions for the storage of filler metal wires). The satisfaction of quality-related requirements...
-
Kinetics of Intermetallic Phase Precipitation in Manual Metal Arc Welded Duplex Stainless Steels
PublicationThe article presents the influence of heat treatment on the kinetics of transformations in lean duplex LDX2101 steel and a weld made of standard duplex 2209 material, which was welded by manual metal arc welding. Changes in the microstructure, hardness, and magnetic phase content were analyzed after heat treatment was conducted at a temperature of 800 °C for a period ranging from 15 to 1440 min. Light and scanning microscopy, Vickers...
-
Microstructure and Mechanical Properties of Combined GTAW and SMAW Dissimilar Welded Joints between Inconel 718 and 304L Austenitic Stainless Steel
PublicationA dissimilar welded joint of Inconel 718 and 304L austenitic stainless steel was prepared using a combined procedure with the gas tungsten arc welding and shielded metal arc welding processes by employing the Ni-based fillers: ERNiCr-3 and ENiCrFe-3. The welded joints were investigated for metallographic testing and mechanical properties, and a relationship was established between the microstructure and the resultant mechanical...
-
Wpływ niezgodności spawalniczych typu ślad zajarzania łuku na strukturę i twardość stali T24
PublicationW pracy opisano badania eksperymentalne dotyczące oceny wpływu cyklu cieplnego podczas tworzenia się niezgodności spawalniczych typu ślady zajarzania łuku na właściwości i strukturę stali T24. Ujawniono wpływ suszenia elektrod na wielkość strefy utlenienia oraz wpływ natężenia prądu spawania na wielkość wykonanego śladu zajarzenia łuku. Przedstawione wyniki badań potwierdzają konieczność wykrywania i usuwania śladów zajarzania...
Year 2022
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublicationIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublicationThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublicationWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
Year 2021
-
Bead-on-Plate Underwater Wet Welding on S700MC Steel
PublicationThe participation of high strength steels in marine and offshore structures is increasing, which makes it necessary to develop recommendations for underwater repair welding works. The article presents the results of bead-on-plate welded specimens made of S700MC high strength steel in underwater wet welding conditions by covered elec- trodes. Three specimens with heat input values in the range 0.91-1.05 kJ/mm were made. The specimens...
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublicationThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
Study on Microstructural Characterization, Mechanical Properties and Residual Stress of GTAW Dissimilar Joints of P91 and P22 Steels
PublicationThis article deals with the dissimilar joining of two different grade Cr-Mo steel (2.25Cr-1Mo: P22 and modified 9Cr-1Mo: P91) for power plant application. The dissimilar butt-welded joint was produced for conventional V groove design by using the gas tungsten arc welding (GTAW) process with the application of an ERNiCrMo-3 Ni-based super alloy filler. A microstructure characterization was performed to measure the inhomogeneity...
Year 2020
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublicationThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Hydrogen embrittlement of X2CrNiMoCuN25-6-3 super duplex stainless steel welded joints under cathodic protection
PublicationThe effect of cathodic polarization conditions on hydrogen degradation of X2CrNiMoCuN25-6-3 super duplex stainless steel welded joints, obtained using flux cored arc and submerged arc welding methods, was evaluated. Slow strain rate tensile tests of base material and welded specimens, ferrite content measurements, scanning electron microscopy observations, and statistical analysis were performed. It was found that hydrogenation...
-
Laser Dissimilar Welding of AISI 430F and AISI 304 Stainless Steels
PublicationA dissimilar autogenous laser welded joint of AISI 430F (X12CrMoS17) martensitic stainless steel and AISI 304 (X5CrNi18-10) austenitic stainless steel was manufactured. The welded joint was examined by non-destructive visual testing and destructive testing by macro- and microscopic examination and hardness measurements. With reference to the ISO 13919-1 standard the welded joint was characterized by C level, due to the gas pores...
-
Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel Alloy
PublicationIn this article, the mechanical properties and microstructure of 304L austenitic stainless steel/Incoloy 800HT nickel alloy dissimilar welded joints are investigated. The joints were made of 21.3 mm × 7.47 mm tubes using the TIG process with the use of S Ni 6082 nickel filler metal. No welding imperfections were found and high strength properties of joints were obtained, meeting the assumed acceptance criteria of the product’s...
-
Plasticity of Bead-On-Plate Welds Made with the Use of Stored Flux-Cored Wires for Offshore Applications
PublicationExtreme atmospheric conditions in the marine and offshore industry are harmful to engineering materials, especially to welded joints, and may cause degradation of their properties. This article presents the results of research on the plasticity of bead-on-plate welds made using two types of seamless, copper plated flux-cored wires. Before welding, spools with wire were stored for 1 month in two distinct locations with different...
Year 2019
-
Determination of moisture resistance of covered electrodes according to PN-EN ISO 14372
PublicationMoisture present in the electrode covering is one of the sources of diffusible hydrogen in welded joints. In order to study the diffusible hydrogen content in deposited metal, a stand for moisturizing covered electrodes, in accordance with the PN-EN ISO 14372 standard, was built. After the stand was completed, a test of moisturizing the electrodes was carried out and measurements of the diffusible hydrogen content in deposited...
-
Effect of Storage Conditions of Rutile Flux Cored Welding Wires on Properties of Welds
PublicationThe influence of storage locations of two grades of rutile flux cored welding wires on their surface condition and the strength of the welds made with them were studied. Wires were stored in real urban conditions (Gdańsk and Katowice) for 1 month, simultaneously recording changes in conditions: temperature and relative humidity of the environment. Visual tests of wires in the delivered and stored condition as well as visual and...
-
Kwalifikowanie technologii lutowania twardego próżniowego stali austenitycznej zgodnie z wymaganiami przepisów ASME BPVC, sekcja IX
PublicationW artykule przedstawiono procedurę kwalifikowania technologii lutowania twardego w piecu próżniowym na przykładzie elementów ze stali wysokostopowej nierdzewnej austenitycznej łączonych lutem miedzianym z grupy F-No. 105, zgodnie z przepisami ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators)....
-
Qualification of brazing procedure for furnace brazing of austenitic steel according to requirements of the ASME BPVC section IX
PublicationThe article presents the procedure for qualifying brazing technology in a vacuum furnace on the example of stainless steel elements joined with copper filler material from the F-No group. 105, in accordance with the ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators). The essential variables...
-
The influence of solution annealing temperature on the properties of Lean Duplex 2101 welded joints in tubes
PublicationThe article presents a technology of TIG longitudinal welding without filler material (142) of heat exchanger tubes made of Lean Duplex 2101. The results of studies on the effect of heat treatment (solution annealing) on tensile strength, plasticity, delta ferrite and the structure of smooth tubes are shown. It was found, that the change in solution annealing temperature across the tested range has an impact on mechanical properties...
-
Wpływ temperatury przesycania na właściwości złączy spawanych rur ze stali typu Lean Duplex 2101
PublicationW artykule przedstawiono wpływ temperatury przesycania w powiązaniu z technologią spawania wzdłużnego metodą TIG (142) rurek stosowanych w budowie wy-mienników ciepła ze stali Lean Duplex 2101. Przedstawiono wyniki badań wytrzymałości na rozciąganie, prób technologicznych określających właściwości plastyczne, makro- i mikro-skopowe oraz pomiaru zawartości ferrytu delta metodą magnetyczną. Ustalono, że zmiana temperatury przesycania...
Year 2018
-
Application of Multivariate Analysis Methods in Welding Engineering
PublicationPhenomena and processes taking place during welding are usually very complex and, for this reason, should be described using multivariate methods. The article discusses the methodological basis and selected application areas as regards the solving of welding problems using statistical multivariate methods. In addition, the article presents exemplary applications of the design of experiment, multiple regression analysis, cluster...
-
Dobór urządzeń do zgrzewania oporowego punktowego z wykorzystaniem analizy skupień
PublicationW pracy omówiono zagadnienie doboru urządzeń do zgrzewania oporowego punktowego, stwierdzając na podstawie przeglądu literatury, że nie istnieje obiektywna metoda wspomagająca decyzję zakupu takich zgrzewarek. Do rozwiązania problemu zaproponowano zastosowanie metod analizy skupień. Zgromadzono i opracowano dane diagnostyczne opisujące 35 zgrzewarek oporowych punktowych, a następnie przeprowadzono ich klasyfikacje metodami Warda...
-
Oznaczenie ilości wodoru dyfundującego w stopiwie drutów proszkowych Kobelco DW-A70L
PublicationNa zlecenie firmy VELTECH Konrad Matolicz wykonano pomiary ilości wodoru dyfundującego w stopiwie dwóch wytopów drutu proszkowego gatunku Kobelco DW-A70L. Ze względu na klasę badanego drutu (H5) pomiary zrealizowano metodą rtęciową, która jest zalecana przez właściwą normę regulującą badania nawodorowania stopiwa spoiw do spawania. Wyniki pomiarów ilości wodoru dyfundującego w stopiwie drutów proszkowych gatunku Kobelco DW-A70L...
-
Wpływ parametrów spawania metodą 136 na ilość wodoru dyfundującego w stopiwie
PublicationW pracy przedstawiono wyniki badań zmian nawodorowania stopiwa drutu proszkowego powodowanych przez założone wartości podstawowych parametrów spawania. Dzięki zastosowaniu teorii planowania eksperymentu stwierdzono, że największy wpływ na Sterowanie wartościami parametrów spawania może prowadzić do zmiany klasy drutu w zakresie H5-H15.
Year 2017
-
Assessment of crack resistance of S355J2+N steel according to SEP 1390 standard
PublicationThe aim of the study was to evaluate the weldability of S355J2+N steel by bending test according to SEP 1390. In the specimen from S355J2+N steel 3 external cracks were found, 1 of which were stopped in the fusion line and 2 in heat affected zone. Results of bending test for investigated grade of steel are positive.
-
Assessment of crack resistance of ship steels according to SEP 1390 standard
PublicationThe aim of the study was to evaluate the weldability of E36 nd NVE-36 steels by bending test according to SEP 1390. In the case of the specimen from E36 steel 9 external cracks were found, 5 of which were stopped in the fusion line and 4 in heat affected zone. In the case of the specimen from NVE-36 steel 8 external cracks were found, 4 of which were stopped in the fusion line and 4 in heat affected zone. Results of bending test...
-
Corrosion behavior of hydrogen charged super duplex stainless steel welded joints
PublicationThe electrochemical behavior of the weld metal, heat-affected zone (HAZ), and base material of super duplex stainless steel (SDSS) welded joints, made with the application of flux-cored arc welding (FCAW) and submerged arc welding (SAW), were investigated with the use of metallographic examinations (optical microscopy and scanning electron microscopy), potentiodynamic polarization measurements and total hydrogen content determination...
-
Diffusible hydrogen management in underwater wet self-shielded flux cored arc welding
PublicationThis article reports the effect of underwater wet welding parameters and conditions on the diffusible hydrogen content in deposited metal for welding with a self-shielded flux cored wire. The diffusible hydrogen content in deposited metal was determined using the glycerin method according to the Plackett-Burman design determining the significance of the effect of the stick out length, welding current, arc voltage, travel speed...
-
Możliwości sterowania ilością wodoru dyfundującego w złączach spawanych
PublicationW pracy omówiono metalurgiczne i technologiczne czynniki wpływające na obecność wodoru dyfundującego w stopiwie uzyskanym w środowisku powietrznym i pod wodą oraz podano metody obniżania jego ilości. Przedstawiono wyniki badań ukierunkowanych na określenie wpływu warunków i parametrów spawania na nawodorowanie stopiwa. Opracowano i podano zależności umożliwiające prognozowanie zawartości wodoru w złączach wykonanych pod wodą...
Year 2016
-
Analiza technologii lutowania próżniowego stali austenitycznej
PublicationCelem badań była ocena poprawności budowy złącza lutowanego próżniowo ze stali austenitycznej oraz analiza składu chemicznego charakterystycznych obszarów badanej próbki. Na podstawie badań wizualnych oraz metalograficznych na mikroskopie skaningowym (w tym analizy EDS) stwierdzono, że badane złącze charakteryzuje się prawidłową geometrią, jednak występują w nim liczne niezgodności (wydzielenia), co świadczy o nieprawidłowych parametrach...
-
Assessment of hydrogenation of deposited metal of P 62 MR covered electrodes
PublicationThe determination of diffusible hydrogen content in deposited metal of P 62 MR covered electrodes for manual metal arc welding by mercury method was carried out. The test results indicate that covered electrodes 62 P MR grade generate a mean of 4.02 ml/100g of diffusible hydrogen in deposited metal, which is consistent with H5 class.
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublicationThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
Ocena jakości złączy lutowanych płytowego wymiennika ciepła
PublicationNa podstawie wyników badań metalograficznych makro- i mikroskopowych oraz badań składu chemicznego (EDS) przeprowadzono ocenę jakości złączy lutowanych płytowego wymiennika ciepła ze stali odpornej na korozję. Stwierdzono występowanie licznych niezgodności w lutowinie oraz strefy dyfuzyjnej o ponadnormatywnej szerokości w materiale rodzimym.
-
Opracowanie technologii spawania laserowego stali o wysokiej wytrzymałości
PublicationWykonano złącza spawane wiązką światła koherentnego ze stali konstrukcyjnej o ultra wysokiej wytrzymałości. Określono zakresy parametrów, które umożliwiają wykonywanie złączy doczołowych oraz napawanie badanej stali.
-
Stanowiska do badań kruchości wodorowej
PublicationW pracy przedstawiono wybrane aspekty niszczenia wodorowego metali oraz złączy spawanych. Przedstawiono stanowiska badawcze wykorzystywane do oceny niszczenia wodorowego, w tym zaprojektowane i wykonane w Zespole Inżynierii Spajania PG stanowisko do realizacji próby SSRT.
-
Temper bead welding of S420G2+M steel in water environment
PublicationThe article presents the idea of the use of Temper Bead Welding (TBW) technique to improve the weldability of high strength steel at underwater wet welding conditions. Wet welding method with the use of covered electrodes is described. This work shows results of metallographic examinations and hardness measurements of samples of S420G2+M steel with weld beads performed under water. It has been shown that Temper Bead Welding technique...
-
Wpływ nawodorowania na odporność korozyjną stali superdupleks spawanej metodą SAW
PublicationW pracy przedstawiono wyniki badań metodą potencjodynamiczną odporności korozyjnej złączy ze stali superdupleks wykonanych procesem SAW. Ustalono, że największą wrażliwością na korozję charakteryzuje się spoina.
-
Zastosowanie próby implant do oceny spawalności stali
PublicationPraca dotyczy oceny spawalności stali o podwyższonej i wysokiej wytrzymałości w aspekcie eksperymentalnego określania skłonności do tworzenia pęknięć zimnych. W artykule opisano metodykę określania wrażliwości na pękanie próbą implant. Przedstawiono również proponowane w literaturze i autorskie sposoby opracowywania i przedstawiania wyników badań rozpatrywaną metodą i ich interpretacji.
Year 2015
-
Assessment of absorbability of seamless flux cored wires stored in extreme conditions
PublicationWater absorption tests by gravimetric method of three specimens of seamless rutile flux cored wires for flux cored arc welding were carried out. Examined wires are characterized by varied absorbability (Wg is ranged from 0.03 to 0.11% after 200 h of moisturizing).
-
Effect of underwater wet welding conditions on the diffusible hydrogen content in deposited metal
PublicationIn the study mercury displacement method was used for determination of diffusible hydrogen amount in deposited metal obtained during underwater wet welding with covered electrodes in laboratory conditions according to a two-level full factorial design for three factors. The factors and their levels were chosen among conditions and parameters of welding in accordance with the results of own preliminary studies. A statistical analysis...
-
Niszczenie wodorowe złączy spawanych ze stali ferrytyczno - austenitycznych typu superdupleks
PublicationPraca dotyczy problematyki niszczenia wodorowego stali superdupleks URANUS 52N+, w szczególności złączy spawanych wykonanych z tej stali z różną ilością wprowadzonego ciepła spawania. Całość opracowania składa się z dwóch części. Część pierwsza to przegląd literatury omawiający głównie wpływ wodoru oraz spawania na strukturę i własności stali dupleks. Część druga, doświadczalna zawiera tezę i cele rozprawy, charakterystykę badanego...
-
Ocena przydatności komercyjnych elektrod otulonych do spawania mokrego pod wodą z wykorzystaniem analizy skupień
PublicationNajbardziej uniwersalną i ekonomiczną metodą remontów konstrukcji eksploatowanych pod wodą jest spawanie mokre elektrodami otulonymi. Ze względu na bardzo dobrą operatywność i stabilność jarzenia się łuku w środowisku wodnym stosuje się elektrody o otulinie rutylowej. Na rynku dostępnych jest kilka gatunków elektrod dedykowanych do prac podwodnych, których cena jest znacznie wyższa niż elektrod komercyjnych. Celem pracy było statystyczne...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublicationThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
Wpływ warunków przechowywania na jakość drutów proszkowych
PublicationW pracy przedstawiono wyniki badań chłonności drutów proszkowych. Badane druty proszkowe zostały poddane ekstremalnym warunkom 60°C i wilgotności względnej 90% przez 240 godzin. Określono chłonność oraz zbadano jakość powierzchni drutów proszkowych po ekspozycji. Wykonano napoiny nawilżonymi drutami proszkowymi i zbadano ilość wodoru dyfundującego w stopiwie.
seen 3389 times