Publications
Filters
total: 733
Catalog Publications
Year 2015
-
An experimental study of high-hydrogen welding processes
PublicationThis paper presents investigation results of determination of the diffusible hydrogen content in deposited metal obtained by means of two most often used methods-the glycerin method and the mercury method. Relation has been defined between results of those methods in the area characteristic of low-hydrogen as well as high-hydrogen welding processes. Relations available in the literature do not include the diffusible hydrogen content...
-
Assessment of absorbability of seamless flux cored wires stored in extreme conditions
PublicationWater absorption tests by gravimetric method of three specimens of seamless rutile flux cored wires for flux cored arc welding were carried out. Examined wires are characterized by varied absorbability (Wg is ranged from 0.03 to 0.11% after 200 h of moisturizing).
-
Badania własności mechanicznych odlewów z żeliwa sferoidalnego (EN-GJS-500-7)
PublicationWykonano badania własności mechanicznych próbek pochodzących z odlewów z żeliwa sferoidalnego
-
Badania złączy lutowanych próżniowo ze stali austenitycznej
PublicationCelem badań była ocena poprawności budowy złącza lutowanego próżniowo ze stali austenitycznej 316L oraz analiza składu chemicznego charakterystycznych obszarów badanej próbki. Na podstawie badań wizualnych oraz metalograficznych na mikroskopie skaningowym (w tym analizy EDS) stwierdzono, że badane złącze charakteryzuje się dużym nasileniem występowania niezgodności, co wynika z silnej segregacji dendrytycznej pierwiastków stopowych....
-
CLAY MINERALS – MINERALOGY AND PHENOMENON OF CLAY SWELLING IN OIL & GAS INDUSTRY
PublicationAmong the minerals found in the earth's crust, clay minerals are of the widest interest. Due to the specific properties such as plasticity, absorbing and catalytic properties clay minerals are used in many industries (oil & gas, chemistry, pharmacy, refractory technology, ceramics etc.). In drilling, a phenomenon of swelling clays is frequently observed. It has an important impact on the cementing quality. During the last few decades...
-
Cold Cracking Of Underwater Wet Welded S355G10+N High Strength Steel
PublicationWater as the welding environment determines some essential problems influencing steel weldability. Underwater welding of high strength steel joints causes increase susceptibility to cold cracking, which is an effect of much faster heat transfer from the weld area and presence of diffusible hydrogen causing increased metal fragility. The paper evaluates the susceptibility to cold cracking of the high strength S355G10+N steel used,...
-
COMPARISON OF THE ABRASION RESISTANCE OF THE SELECTED BIOMATERIALS FOR FRICTION COMPONENTS IN ORTHOPEDIC ENDOPROSTHESES
PublicationRosnące z każdym rokiem zapotrzebowanie na endoprotezy stawów ortopedycznych przy jednoczesnym dążeniu do zwiększenia ich trwałości i wyeliminowania negatywnych skutków ubocznych produktów zużycia, które mogą wywoływać proces zapalny w tkankach determinuje potrzebę poszukiwania nowych biomateriałów, bądź metody modyfikacji ich powierzchni. Nadrzędnym celem prowadzonych przez nas badań było oszacowanie intensywności zużycia ściernego...
-
Development of Education Tomorrow’s Engineers at the Faculty of Mechanical Engineering in GUT
PublicationPaper presents educational activity of Faculty of Mechanical Engineering of the Gdańsk University of Technology. Faculty of Mechanical Engineering is one of the largest departments of the Gdańsk University of Technology (GUT), currently educating about 3 000 student. The Faculty of Mechanical Engineering offers studies in different areas: Mechanical Engineering, Medical and Mechanical Engineering, Materials Engineering, Mechatronic,...
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublicationThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Effect of underwater wet welding conditions on the diffusible hydrogen content in deposited metal
PublicationIn the study mercury displacement method was used for determination of diffusible hydrogen amount in deposited metal obtained during underwater wet welding with covered electrodes in laboratory conditions according to a two-level full factorial design for three factors. The factors and their levels were chosen among conditions and parameters of welding in accordance with the results of own preliminary studies. A statistical analysis...
-
ESTIMATION OF YOUNG`S MODULUS OF THE POROUS TITANIUM ALLOY WITH THE USE OF FEM PACKAGE
PublicationPorous structures made of metal or biopolymers with a structure similar in shape and mechanical properties to human bone can easily be produced by stereolithographic techniques, e.g. selective laser melting (SLM). Numerical methods, like Finite Element Method (FEM) have great potential in testing new scaffold designs, according to their mechanical properties before manufacturing, i.e. strength or stiffness. An example of such designs...
-
Fabrication of Composite Polyurethane/Hydroxyapatite Scaffolds Using Solvent-Casting Salt Leaching Technique
PublicationScaffolds are porous three-dimensional structures which are used to fill bone losses and make them possible to cells to grow. Many different structural and biological properties are required from them: porosity, mechanical strength and biocompability. The present research is aimed at development of composite polyurethane/hydroxyapatite scaffolds by using the solvent-casting salt leaching method. The SEM examinations were applied...
-
Final report on noise and rolling resistance
PublicationWork Package 6 deals with environmental impacts of PERS use, including noise and rolling resistance. This report covers preliminary noise tests performed in the laboratory and at the road test sites. The obtained results indicate that PERS material reduce noise considerably - up to 12 dB in comparison to SMA16 reference surface. Noise reduction properties are especially visible in the case of factory produced PERS slabs supplied...
-
Impact Behaviour of Glass Fribre /Epoxy Composites with Nano-Enhanced Resin after Water Exposure
PublicationImpact behaviour of glass fibre /epoxy composites with nano- SiO2 modified resin was studied in terms of low velocity impact after water exposure. Nanocomposites with 1%, 2%, 3% 5% 7% nano-SiO2 (Nanopox- Evonic) were investigated. Peak impact load and impact damage area as a function of nanoparticle contents were compared for dry specimens and for samples exposed to water (0.7 %wt. 1.7% water absorbed) at 1J, 2J 3J impact energies....
-
IMPACT-TOUGHNESS INVESTIGATIONS OF DUPLEX STAINLESS STEELS
PublicationDuplex stainless steels are very attractive constructional materials for use in aggressive environments because of their several advantages over austenitic stainless steels. Duplex steels have excellent pitting and crevice corrosion resistance, are highly resistant to chloride stress-corrosion cracking and are about twice as strong as common austenitic steels. Better properties are associated with their microstructures consisting...
-
IMPULSE NOISE ASSOCIATED WITH FIRING HANDHELD MILITARY WEAPONS
PublicationSports, hunting and military shooting grounds are well known sources of noise that can be disruptive both for people present at those facilities, as well as for people and animals that live nearby. What is more, shooters are also subjected to very painful and dangerous impulse noise. The paper discusses the issues related to the noise immission during firing of small firearms of military type that are typical for Poland. The experiments...
-
INFLUENCE OF PRESERVATIVE ON THE TENSILE STRENGTH OF THE TISSUE OF PORCINE CIRCULATORY SYSTEM
PublicationCurrently one of the leading causes of death worldwide is heart diseases which include calcification of heart valves and vascular aneurysm. There are many biomaterials that can substitute pathologically altered tissue, however, none of them is as perfect as native tissue. Currently, scientists are looking for new biomaterials that can be successfully implanted without exposing the patient to reoperation. Each material introduced...
-
Influence of Road Wetness on Tire-Pavement Rolling Resistance
PublicationRolling resistance of tires is one of the most important factors influencing energy consumption of road vehicles, especially on rural roads. For practical reasons, most of rolling resistance measurements are usually performed for dry road conditions. Based on the fact that roads are wet during a considerable time over the year and as part of the projects MIRIAM, ROLRES and ROSANNE, the TUG (Technical University of Gdańsk) in Poland...
-
Influence of Spatial Structures of 316L Stainless Steel on Its Cavitation Erosion Resistance
PublicationCavitation erosion performance of modified macroscopic internal structure 316L stainless steel was investigated. The samples processed by means of SLM method were subjected to cavitation erosion test. The scanning electron microscope Philips 30/ESEM was used to examine morphology of eroded surface.
-
Influence of Staphylloccoccus bacteria adhesion on the degradation of the Ti6Al4V alloy
PublicationThe paper deals with bacteria adhesion and the degradation of the Ti6Al4V alloy
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublicationTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Magnetoelectric effect in (BiFeO3)x–(BaTiO3)1-x solid solutions
PublicationThe aim of the present work was to study magnetoelectric effect (ME) in (BiFeO3)x–(BaTiO3)1x solid solutions in terms of technological conditions applied in the samples fabrication process. The rapidly growing interest in these materials is caused by their multiferroic behaviour, i.e. coexistence of both electric and magnetic ordering. It creates possibility for many innovative applications, e.g. in steering the magnetic memory...
-
Modyfikacja powierzchni stopu Ti13Nb13Zr metodą implantacji jonowej w aspekcie zastosowania na elementy trące w endoprotezach ortopedycznych
PublicationW celu określenia wpływu wybranych czynników tribologicznych na intensywność zużycia ściernego pary trącej złożonej z nowoczesnego stopu tytanu Ti13Nb13Zr oraz PE-UHMW, przeprowadzono badania tribologiczne. Uzyskane wyniki badań wykazały zbyt niską odporność na zużycie ścierne stopu tytanu Ti13Nb13Zr. Stosunkowo niska trwałość badanego stopu tytanu, wskazuję na potrzebę modyfikacji jego powierzchni w celu zwiększenia twardości....
-
Nano-particle doped hydroxyapatite material evaluation using Spectroscopic Polarization Sensitive Optical Coherence Tomography
PublicationBio-ceramics such as hydroxyapatite (HAp) are widely used materials in medical applications, especially as an interface between implants and living tissues. There are many ways of creating structures from HAp like electrochemical assisted deposition, biomimetic, electrophoresis, pulsed laser deposition or sol-gel processing. Our research is based on analyzing the parameters of the sol-gel method for creating thin layers of HAp....
-
Niszczenie wodorowe złączy spawanych ze stali ferrytyczno - austenitycznych typu superdupleks
PublicationPraca dotyczy problematyki niszczenia wodorowego stali superdupleks URANUS 52N+, w szczególności złączy spawanych wykonanych z tej stali z różną ilością wprowadzonego ciepła spawania. Całość opracowania składa się z dwóch części. Część pierwsza to przegląd literatury omawiający głównie wpływ wodoru oraz spawania na strukturę i własności stali dupleks. Część druga, doświadczalna zawiera tezę i cele rozprawy, charakterystykę badanego...
-
Noise Generated by Tyres Designet for Electric Vehicles - Results of Laboratory Experiments
PublicationA few years ago, electric and hybrid vehicles were rarely seen on public roads and were considered more as exotic curiosities or even as a sign of extravagance than a practical means of transport. Nowadays the situation has changes significantly. This was caused both by the technical development and legislative actions, as well as the organizational nature promoting the purchace and use of low emission vehicles. Electric vehicles...
-
Ocena jakości złączy lutowanych ze stali austenitycznej
PublicationCelem badań była ocena poprawności budowy złącza lutowanego próżniowo ze stali austenitycznej 316L oraz analiza składu chemicznego charakterystycznych obszarów badanej próbki. Na podstawie badań wizualnych oraz metalograficznych na mikroskopie skaningowym (w tym analizy EDS) stwierdzono, że badane złącze charakteryzuje się prawidłową budową i nielicznymi niezgodnościami zlokalizowanymi w pobliżu lica lutowiny. Wyniki analiz EDS...
-
Ocena możliwości naprawy rurociągu podwodnego ze stali API 5L X65 przy zastosowaniu spawania mokrego
PublicationPraca dotyczy zagadnień związanych z naprawami podwodnych rurociągów ze stali API 5L X65, które ulegają uszkodzeniom eksploatacyjnym. Wykonano w warunkach spawania mokrego elektrodami otulonymi złącza naprawcze symulowanych pęknięć w elementach rurociągu z izolacją polimerową oraz przeprowadzono ich badania nieniszczące, twardości oraz metalograficzne makroi mikroskopowe. Stwierdzono występowanie niezgodności spawalniczych typu:...
-
Ocena przydatności komercyjnych elektrod otulonych do spawania mokrego pod wodą z wykorzystaniem analizy skupień
PublicationNajbardziej uniwersalną i ekonomiczną metodą remontów konstrukcji eksploatowanych pod wodą jest spawanie mokre elektrodami otulonymi. Ze względu na bardzo dobrą operatywność i stabilność jarzenia się łuku w środowisku wodnym stosuje się elektrody o otulinie rutylowej. Na rynku dostępnych jest kilka gatunków elektrod dedykowanych do prac podwodnych, których cena jest znacznie wyższa niż elektrod komercyjnych. Celem pracy było statystyczne...
-
Opinia techniczna dotycząca połączeń spawanych rurociągu chloru gazowego
PublicationWykonano badania mające na celu ustalenie przyczyny uszkodzenia rurociągu ze stali nierdzewnej przeznaczonego do transportu chloru.
-
Opony i nawierzchnie drogowe dla samochodów elektrycznych
PublicationOd czasu wynalezienia koła, które to wydarzenie miało miejsce około 6 tys. lat temu, rozpoczęła się era transportu kołowego trwająca do dzisiaj. W początkowym okresie koło, a często walec, wykorzystywane były jedynie do przesuwania ciężkich przedmiotów na niewielkie odległości. Potem pojawiły się pojazdy kołowe napędzane siłą mięśni zwierząt pociągowych. Dopiero pod koniec XVIII wieku zbudowano pierwsze pojazdy, które możemy zakwalifikować...
-
OPRACOWANIE TECHNOLOGII OTRZYMYWANIA MEMBRAN CHITOZANOWYCH DO ZABIEGU STEROWANEJ REGENERACJI KOŚCI
PublicationPoniżej przedstawione badanie miało na celu wytworzenie asymetrycznych membran chitozanowych do zabiegu sterowanej regeneracji kości w stomatologii. W celu zbadania uzyskanej struktury wykonano mikrofotografie SEM.
-
Poroelastic Low Noise Road Surfaces
PublicationNoise is one of the most important problems related to road traffic. During the last decades, noise emitted by engine and powertrain of vehicles was greatly reduced and tyres became a clearly dominant noise source. The paper describes the concept of low noise poroelastic road surfaces that are composed with mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and are much more flexible...
-
Project of hip joint endoprothesis for an individual patient with materials selection
PublicationThis work includes the hip replacement design, based on the patient's medical records, the description of creation process and materials used for individual components.
-
Risks related to car fire on innovative Poroelastic Road Surfaces-PERS
PublicationTo reduce tyre/road noise, the concept of poroelastic road surfaces (PERS) was invented. PERS is a road surface material that is porous, and at the same time, it is flexible because of the substantial amount of rubber granulate content (from 20% to 85%). The rubber and stone particles are bound by polyurethane resin instead of bitumen. It was feared that in case of fire, because of the high content of rubber and polyurethane, there...
-
Rolling Resistance And Tire/Road Noise on Rubberized Asphalt Pavement In Poland
PublicationThe paper presents results of tire/road noise and rolling resistance measurements performed on stone-matrix asphalt (SMA) that contains rubberized asphalt developed and produced by the company in Poland. Bituminous binder was modified with polymer and additive of crumb rubber. First observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger car...
-
Skłonność stali S460ML do powstawania pęknięć zimnych podczas spawania pod wodą metodą mokrą
PublicationW pracy przedstawiono problem spawania stali o podwyższonej wytrzymałości S460ML podczas wykonywania złączy w środowisku wodnym, metodą mokrą, elektrodami otulonymi. Omówiono zachowanie się złączy próbnych (próba Tekken) podczas ich spawania pod wodą. Zrealizowane badania pokazały, iż stal S460ML w warunkach spawania mokrego (MMA) jest skłonna do tworzenia pęknięć zimnych w spoinie.
-
Spawalność tytanu Grade 2 na przykładzie płaszczowo-rurowego wymiennika ciepła
PublicationW artykule scharakteryzowano właściwości, obszary zastosowania i problemy związane ze spawalnością tytanu i jego stopów. Opracowano technologię spawania metodą TIG płaszczowo-rurowego wymiennika ciepła typu JAD B z tytanu Grade 2, zaprezentowano wyniki badań nieniszczących i niszczących złączy spawanych. Szczególną uwagę zwrócono na trudności związane z przygotowaniem krawędzi elementów do spawania i wynikające z nich niezgodności...
-
Stress anisotropy characterisation with the help of Barkhausen effect detector with adjustable magnetic field direction
PublicationIn the paper we describe a novel apparatus for the measurement of the Barkhausen noise (BN) angular dependence, which in turn may be indicative of the stress induced anisotropy of magnetic properties. Such dependence can be further used for the stress distribution evaluation. The change of magnetization direction in the material is obtained by varying the magnetic flux density in two perpendicular yokes of the apparatus. We present...
-
Surface treatment of C80U steel by long CO2 laser pulses
PublicationThe paper presents the results of laser-melted C80U steel. The processed steel was placed between two permanent magnets and laser beam whose scanning velocity was 10 mm/s. CO2 laser beam was working in pulse mode. Pulses were generated at 100% of the average preset power of 700W, with 45 ms irradiation, zero interval between pulses and beginning of pulse repetition upon the achievement of the average laser power. During the operation,...
-
The bahaviour of selected silver coated body implants in presence of various bacteria
PublicationThe article deals with implants covered with silver nanoparticles and its influence on bacteria adhesion.
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublicationThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
The effect of tire aging on acoustic performance of CPX reference tires
PublicationReduction of tire/road noise is one of the biggest environmental challenges of road traffic. To reduce that noise it is necessary to perform acoustic measurements on the base of wellproven standard procedures. One method of measurements that is in common use, namely the Close Proximity Method (CPX), is described in standard ISO-DIS 11819-2. As this method is used to classify road surfaces regarding their influence on vehicle noise,...
-
THE EVALUATION OF THE ABRASIVE WEAR OF THE TI13Nb13ZR ALLOY IMPLANTED BY NITROGEN IONS FOR FRICTION COMPONENTS OF THE HIP JOINT ENDOPROSTHESES
PublicationZ uwagi na potrzeby społeczne, a zwłaszcza rosnące zapotrzebowanie na endoprotezy stawów biodrowego i kolanowego oraz uwzględniając fakt, że procesy tribologiczne odgrywają wiodącą rolę w procesie utraty stabilności endoprotez ortopedycznych i decydują o ich trwałości, uznano za celowe przeprowadzenie oceny wpływu implantacji jonowej na zużycie ścierne biostopu Ti13Nb13Zr. Do badań wykorzystano pary trące: nieimplantowany stop...
-
The influence of road surface unevenness on tyre rolling resistance
PublicationThe geometric characteristics of road surface substantially affect the interaction between tyre and road. Depending on pavement texture wavelength, the texture chiefly affects tyre/road friction, rolling resistance, interior and exterior noise, tyre wear, and ride comfort. The article presents results of investigations on the influence of road surface unevenness on the rolling resistance of passenger car and truck tyres. The tests...
-
THE POSSIBILITY OF USE OF LASER-MODIFIED Ti6Al4V ALLOY IN FRICTION PAIRS IN ENDOPROSTHESES
PublicationThe purpose of this paper is to show results of laser treatment at cryogenic conditions of the Ti6Al4V alloy used for orthopedic applications. That modification process ought to bring beneficial changes of microstructure and residual stresses in the surface layer. The paper presents the abrasive wear of the base and laser remelted material in association with ceramics Al2O3. Despite the surface cracking after laser treatment the...
-
Use of X-ray radiography in the diagnosis of bonded anchors
PublicationKotwy wklejane należą do najbardziej popularnych metod montażu elementów konstrukcyjnych. Promieniowanie rentgenowskie częściowo umożliwia diagnostykę zespolenia lepiszcza z podłożem. W pracy przedstawiono wyniki analizy wpływu parametrów technicznych aparatów rentgenowskich na sposób i dokładność wykonania zdjęć diagnostycznych osadzenia kotew stalowych przy zastosowaniu lepiszcza syntetycznego
-
Wpływ modyfikacji laserowej stopu Ti13Nb13Zr na mikrostrukturę powłok hydroksyapatytowych
PublicationDotychczasowe badania powierzchni wszczepów tytanowych dla chirurgii kostnej wykazały, że osteointegracja na powierzchniach rozwiniętych jest znacznie szybsza niż na powierzchniach gładkich, co za tym idzie chropowatość powierzchni implantu ma bardzo duży wpływ na adhezję składników środowiska biologicznego. W artykule przedstawiono wstępne wyniki badań dotyczące wpływu chropowatości powierzchni stopu Ti13Nb13Zr o bardzo małym...
-
Wpływ techniki ściegu odpuszczającego na spawalność stali S355G10+N pod wodą
PublicationW artykule scharakteryzowano idee spawania mokrego oraz stosowanie techniki ściegów odpuszczających. Przedstawiono wpływ zastosowania techniki ściegu odpuszczającego na skłonność stali podwyższonej wytrzymałości S355G10+N do pękania zimnego wyrażoną twardością strefy wpływu ciepła w warunkach spawania podwodnego. Badania przeprowadzono na próbkach spawanych techniką mokrą elektrodami otulonymi (MMA). W wyniku zrealizowanych badań...
-
Wpływ warunków przechowywania na jakość drutów proszkowych
PublicationW pracy przedstawiono wyniki badań chłonności drutów proszkowych. Badane druty proszkowe zostały poddane ekstremalnym warunkom 60°C i wilgotności względnej 90% przez 240 godzin. Określono chłonność oraz zbadano jakość powierzchni drutów proszkowych po ekspozycji. Wykonano napoiny nawilżonymi drutami proszkowymi i zbadano ilość wodoru dyfundującego w stopiwie.
-
WRONG WAY! - amerykańskie doświadczenia w oznakowaniu dróg szybkiego ruchu
PublicationOd kilku lat w Polsce mamy już liczącą się sieć autostrad i dróg szybkiego ruchu, które bez wątpienia są kluczem do szybkiego i bezpiecznego poruszania się pojazdów samochodowych. W związku z rozwojem sieci drogowej pojawił się jednak nowy problem, który jak dotychczas jest w naszym kraju zupełnie - jazda "pod prąd". Niniejszy artykuł dotyczy tego problemu, gdyż regularnie co kilka tygodni dochodzą do nas informacje o poważnych...
-
Wstępne badania spawalności stali dupleks typu 2205 w środowisku wodnym metodą mokrą
PublicationW pracy przedstawiono wstępne wyniki badań spawalności stali ferrytyczno-austenitycznej odpornej na korozję typu dupleks 2205 w środowisku wodnym, metodą mokrą, elektrodami otulonymi. Omówiono wpływ cyklu cieplnego spawania na strukturę i właściwości napoin wykonanych pod wodą. Zrealizowane wstępne badania wykazały przydatność stali dupleks do spawania w środowisku wodnym.
-
X-Ray Diffraction, Mössbauer Spectroscopy and Magnetoelectric Effect Studies of Multiferroic Bi5Ti3FeO15 Ceramics
PublicationBi5Ti3FeO15 ceramics belongs to multiferroic class of materials. In this work it was prepared by solid-state sintering method and investigated by X-ray diffraction, Mössbauer spectroscopy, and magnetoelectric effect measurements. As it was proved by X-ray diffraction studies the single-phase Bi5Ti3FeO15 compound was obtained. The Mössbauer investigations revealed paramagnetic character of the compound at room temperature as well...
-
Zastosowanie promieniowanie rentgenowskiego w diagnostyce montażu kotew wklejanych
PublicationArtykuł przedstawia wyniki pomiarów skuteczności montażu kotew wklejanych wykonanych z zastosowaniem bezinwazyjnej metody diagnostycznej jaką jest promieniowanie rentgenowskie. badania wykonano dla przypadku osadzenia kotew w bloczkach wapienno-piaskowych. Przebadano wpływ lokalizacji miejsc osadzenia kotew na sposób kształtowania się połączenia pomiędzy żywicą a materiałem bloczka. Główny nacisk położono na dobór parametrów aparatu...
-
Zjawisko kawitacji ultradźwiękowej, jego zastosowania oraz metodyka badań niszczenia, które powoduje
PublicationW artykule przedstawiono krótką charakterystykę zjawiska kawitacji, ze szczególnym naciskiem na kawitację wywołaną ultradźwiękami. Nakreślony został mechanizm niszczenia kawitacyjnego powierzchni po czym opisane zostały współczesne zastosowania zjawiska z zakresu techniki oraz medycyny. Przedstawiono również główne założenia metodyki badań niszczenia kawitacyjnego za pomocą generatora ultradźwięków zgodne z normą ASTM-G32 oraz...
Year 2014
-
A New Microwave Ceramic – Polymer Composite with 0-3 Connectivity
PublicationGoal of the present research was to fabricate and study two-phase BiNbO4//PVDF composites with 0-3 connectivity. Such composite consists of there-dimensionally connected polymer matrix loaded with dielectric ceramic particles. In the present case BiNbO4 powder acted as an active phase (dispersed phase) whereas polyvinylidene fluoride (PVDF) acted as a non-active (passive) phase (matrix). BiNbO4//PVDF composites with the volume...
-
Analiza skupień jako metoda wspomagania decyzji zakupu urządzeń prądu stałego do spawania metodą TIG
PublicationW pracy podjęto zagadnienie wspomagania decyzji zakupu odpowiedniego spawalniczego źródła prądu. Zaproponowano rozwiązanie problemu z wykorzystaniem metod analizy skupień. Przedstawiono wyniki klasyfikacji 69 urządzeń prądu stałego do spawania TIG metodami Warda i k-średnich dla odpowiednio dobranego i przygotowanego zestawu cech diagnostycznych. Na podstawie wyników uznano, że analiza skupień może być skuteczną metodą wspomagania...
-
Analysis and Comparison of Safety of Children and Adult Passenger in Car Based on Crash Tests Results
PublicationMost important features of the child seat were presented. There was made analysis of selected dynamic loads acting on mannequins heads during a collision. Comparison of loads acting on the kid in a child seat and the other passengers in a car is presented. In analysis of the results particular attention has been paid on the children's secure in a car. The phenomena of collision child's occipital bone with seat backrest was described....
-
Analysis of Rolling Resistance of Tires With Run Flat Insert
PublicationRun flat properties are required for tires intended for special applications like military or rescue vehicles. Run-Flat inserts make possible to drive a car or truck, with certain restrictions, also when inflation pressure is very low or non-existing (after tire damage). Rolling resistance of tires rolling the inserts increases considerably in relation to the rolling resistance of properly inflated tires. This paper presents results...
-
Badania przyczyn uszkodzenia U-rurki wymiennika ciepła instalacji 150-E06
PublicationWykonano kompleksowe badania przyczyn uszkodzenia U-rurki wymiennika ciepła wykonanej ze stali A213 T11. Wskazano możliwe przyczyn wystąpienia uszkodzenia.
-
Badania warunków spawania pod wodą metodą lokalnej komory suchej
PublicationZastosowanie do spawania pod wodą metody lokalnej komory suchej stanowi alternatywę dla mających znacznie większe znaczenie praktyczne metod spawania w warunkach mokrych. Zwiększenie zakresu stosowania procesów spawalniczych przy miejscowym odizolowaniu obszaru spawania od wody uwarunkowane jest opracowywaniem nowych rozwiązań konstrukcyjnych, ale także poszerzaniem stanu wiedzy o przebiegu procesu m.in. poznaniem warunków panujących...
-
BADANIA ZŁĄCZY SPAWANYCH BIMETALU ZGRZEWANEGO WYBUCHOWO STALI NIESTOPOWEJ SA516 Gr. 60 ZE STOPEM MONEL 400
PublicationW pracy przedstawiono wyniki badań doczołowych złączy spawanych bimetalu typu stal niestopowa SA516 Gr. 60 - monel 400 (SB127 UNS 04400). Badany bimetal został wytworzony poprzez zgrzewanie wybuchowe. Określono własności mechaniczne, rozkład twardości oraz strukturę otrzymanych złączy. Zwrócono uwagę na trudności technologiczne spawania tego rodzaju materiału oraz możliwość generowania niezgodności spawalniczych.
-
Bead-on-plate welding on S235JR steel by underwater local dry chamber process
PublicationThe article presents the results of the effect of parameters of underwater local dry chamber welding on the properties of padding welds. The effect of heat input and the type of shielding gas on the structure and hardness of welds was established. the functions for estimating the maximum hardness of the heat affected zone have been also elaborated.
-
BIOMATERIALS AND IMPLANTS IN CARDIAC AND VASCULAR SURGERY - REVIEW
PublicationCurrently, on prosthesis in cardiac blood vessels and heart valves are used materials of animal or synthetic origin. For animal materials include, among others pericardial sac in which is the heart. Materials such as this (natural) are characterized by a remarkable biocompatibility within the human body, but their main disadvantage is the relatively low durability. In turn, synthetic materials, which include the austenitic chromium-nickel-molybdenum...
-
Comparative in vitro research of the Human Aortic Bioprosthesis
PublicationE valuate of the usefulness and reliability of structures based on the analysis of recorded parameters determining the flow through the Human Aortic Bioprosthesis (HAB) have been dealt with. By flow parameters changes determining the performance environment of prosthesis analyzed change of the motion dynamics of the valve leaflets as a function of pressure, thereby determining the degree of alignment of the prosthesis to the performance...
-
Comparison of road and laboratory measurements of tyre/road noise
PublicationTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
Dielectric Properties of BiNbO<sub>4</sub>-Based Ceramic-Polymer Composites with 0-3 Connectivity
PublicationIn the present study two-phase BiNbO4//PVDF composites with 0-3 connectivity were studied by impedance spectroscopy within the frequency range Δν=100Hz-1MHz at room temperature. Polyvinylidene fluoride (PVDF) acted as a matrix whereas bismuth niobate (BiNbO4) powder acted as a dispersed phase. The volume fraction of the ceramic phase was cV=2, 4, 6, 8, 10, 16 and 20vol%. Analysis of the impedance data registered for composites...
-
Diffusible hydrogen content in deposited metal of multilayer welded joints
PublicationThe article describes manufacturing technology of multilayer joints in terms of control the diffusible hydrogen content. Diffusible hydrogen content in deposited metal for multilayer welded joints made of covered rutile electrodes or covered cellulosic and basic electrodes was determined. It was found that after four beads, the diffusible hydrogen content decreases in the case of the first technology from 36 ml/100 g to 18 ml/100...
-
Diffusible Hydrogen Control in Flux Cored Arc Welding Process
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper an experimental...
-
Effect of microstructure on mechanical properties and corrosion resistance of 2205 duplex stainless steel
PublicationThis paper presents results of the research on impact of microstructure of austenitic-ferritic steel of duplex type on its mechanical properties and susceptibility to stress corrosion cracking. As showed, improper processing technologies more and more often used in shipbuilding industry for plates and other half-finished products made of duplex steel may cause significant lowering their properties, which frequently makes their...
-
Effect of microstructure on mechanical properties of BA1055 bronze castings
PublicationThe article presents research results performed on aluminum bronze CuAl10Fe5Ni5 (BA1032) castings used for marine propellers. Metallographic studies were made on light microscope and a scanning electron microscope to assess quantitatively and qualitatively the alloy microstructure. It has been shown that the shape, size and distribution of the iron-rich phase precipitates in bronze microstructure significantly affect its mechanical...
-
Ekspertyza połączeń lutowanych rur miedzianych
PublicationCelem pracy było ustalenie rodzaju lutu zastosowanego do spajania rur miedzianych o średnicy 20 mm, ustalenie technologii lutowania oraz wydanie opinii czy połączenia lutowane gwarantują bezpieczeństwo podczas użytkowania rurociągu w wewnętrznej instalacji gazowej w budownictwie mieszkaniowym
-
Ekspertyza przyczyn korozji złącza spawanego rury ze szwem 129x3,0 mm z instalacji flokulatora
PublicationCelem pracy było ustalenie przyczyn korozji złącza spawanego rury ze szwem 130x3,0 mm z instalacji flokulatora. Instalacja była wykonana ze stali nierdzewnej AISI 316L. Zakres pracy obejmował: wykonanie analizy EDX składu chemicznego spoiny oraz nalotów obecnych na rurociągu, wykonanie badań próbek metalograficznych wraz z określeniem mikrostruktury
-
Environmental degradation of Ti alloys in artificial saliva and a role of fluorides
PublicationThe titanium and its alloys are potentially prone to hydrogen embrittlement, including those proposed for dental implants. The research has been aimed to assess a susceptibility to environment-enhanced degradation of the Ti-13Zr-13Nb alloy in artificial saliva with or without hydrofluoric acid, subject or not to cathodic polarisation. The results have shown that even if artificial saliva is safe environment, both cathodic polarization...
-
Evaluation of Wear Resistance of Ti alloys used for elements friction of knee endoprosthesis
PublicationThe paper presents research results of resistance to abrasive wear of titanium alloys: Ti6Al4V (commonly used) and Til3Nb13Zr (alloy of new generation) in association with polyethylene (UHMW-PE) predisposed for elements on pair of the knee endoprosthesis. The results were analysed from the point of possibility of an use of new generation titanium alloys as components of such implants. The tests of resistance to abrasive wear of...
-
HOW EFFICIENT IS NOISE LABELING OF TIRES?
PublicationSince 2012 all new tires in Europe must be labeled. The label contains general information about tire performance concerning rolling resistance (that corresponds to fuel economy), noise emission and wet grip (only for passenger car tires). Measurements of noise performance of tires must be performed according to the Annex 3 of the Regulation No 117 of the Economic Commission for Europe of the United Nations. The regulation specifies...
-
Hydrogen Damage in Superaustenitic 904L Stainless Steels
Publicationresults on the influence of hydrogen on corrosion resistance and of hydrogen embrittlement of 904L superaustenitic stainless steel were investigated. The cracking behavior was studied by performing a slow strain rate test in synthetic seawater under varying cathodic polarization conditions. The results showed that the steel’s plasticity varied with the applied cathodic current density. Significant reductions in ductility were found,...
-
IN VIVO DEGRADATION OF BIOMATERIALS
PublicationThe material designed to be introduced into the human tissue should be biocompatible and biofunctional. Unless it is so, the body may respond to the implant in different ways. An inflammation reaction may appear such as: parting of items of the implant surface resulting from fraction or pressure. The condition of the surface has an important influence on the usefulness of the implant. The required values depend on the implant function...
-
Influence of Phase Composition on Dielectric Properties of Bismuth-Based Ceramics with Scheelite-Type Structure
PublicationGoal of the present research was to study dielectric properties of BiNbO4 ceramics fabricated by solid state reaction route followed with pressureless sintering. The samples were fabricated from the mixture of oxides, viz. Nb2O5 and Bi2O3. Apart from stoichiometric amount an excess of 3%, 5% and 10% by mole of Bi2O3 was used. It was found that an excess amount of Bi2O3 oxide caused formation of Bi5Nb3O15 minor phase in amount of...
-
Inżynieria Powierzchni: Wybrane zagadnienia
PublicationZakres tematyczny niniejszego podręcznika obejmuje zagadnienia z dziedziny inżynierii powierzchni dotyczące podstawowych procesów niszczenia powierzchni tworzyw metalicznych oraz metod stosowanych w celu podwyższenia odporności korozyjnej oraz odporności na zużycie. Wybrano i opisano głównie tradycyjne technologie inżynierii powierzchni takie jak galwanotechnika, pokrywanie ogniowe (zanurzeniowe), natryskiwanie cieplne, napawanie,...
-
LOW NOISE TIRES FOR HYBRID AND ELECTRIC VEHICLES
PublicationLow Emission Vehicles that are hybrid and electric cars may benefit from specially designed tires that are optimized for driving conditions typical for such vehicles. It is possible that in the future Low Emission Vehicles, especially passenger cars, will substitute conventional vehicles in all applications, however for the time being they are mostly used in urban and suburban areas. Urban traffic has a rather low demand for grip...
-
Methods of Tire Rolling Resistance Measurements
PublicationTire rolling resistance is one of the factors related to tire/road interaction that has important influence on road vehicles performance. Raising fuel price and increased concern related to the environmental changes result in growing interest in reduction of tire rolling resistance that influences fuel consumption, especially in free-flowing highway traffic with moderate speeds. There are several methods of tire rolling resistance measurements....
-
Mn Road Facility Badania nawierzchni drogowych w amerykańskim stylu
PublicationPomimo znacznego rozwoju technik modelowania matematycznego oraz badań laboratoryjnych nie jest obecnie możliwe wyeliminowanie badań nawierzchni drogowych i ich monitorowania w warunkach drogowych. W pracy przedstawiono drogowe badania oporu toczenia opon samochodowych na torach doświadczalnych Francji i Stanów Zjednoczonych wykonane za pomocą przryczepy dynamometrycznej zbudowanej w Politechnice Gdańskiej. Podano przykładowe wyniki...
-
Morphology and properties of nanotubular oxide layer on the Ti13Zr13Nb alloy
PublicationThe Ti13Zr13Nb alloy in solid and porous form was oxidised. The constant voltage 20 V, oxidation time 0.5 and 1 h, and 1 M H3PO4 (orthophosphoric acid) with addition of HF (hydrofluoric acid) as a test solution were applied. SEM (Scanning Electron Microscope) examinations of surface, EDS (Energy Dispersive X-ray Spectroscopy) chemical analysis, nanohardness and nano-scratch tests, and corrosion potentiokinetic tests at various...
-
Mössbauer Spectroscopy and Magnetoelectric Effect Studies of Multiferroic Ceramics Based on BiFeO<sub>3</sub>
PublicationIn this work the results of investigations for (BiFeO3)x(BaTiO3)1-x and Bi1-xNdxFeO3 solid solutions are described. Samples were prepared by the conventional solid-state sintering method. X-ray diffraction, 57Fe Mössbauer spectroscopy, and magnetoelectric effect measurements were applied as complementary methods to determine the structure and magnetic properties of materials. For (BiFeO3)x(BaTiO3)1-x solid solutions Mössbauer...
-
Nanotubular oxide layers and hydroxyapatite coatings on ‘Ti–13Zr–13Nb’ alloy
PublicationThe presented research was aimed to determine the mechanical properties of the nanotubular oxide layer covered with hydroxyapatite coating. The Ti–13Zr–13Nb alloy was oxidised in 1M phosphoric acid with an addition of 0?5% HF for HF solution at 20 V voltage. The electrochemically assisted deposition of hydroxyapatite was performed at cyclic polarisation in NH4H2PO4 and CaCl2 solution at 80uC. The mechanical properties were determined...
-
Ocena przyczyn awarii robota BT-1000
PublicationPrzeprowadzono analizy kinematyki ruchu elementów głowicy robota oraz obliczenia symulacyjne stanu obciążeń połączeń ruchowych w celu oceny rzeczywistego stanu pracy tych elementów. Oceniono modyfikacje konstrukcyjne i sformułowano wnioski odnośnie możliwości zwiększenia trwałości najbardziej obciążonych elementów.
-
Opinia dotycząca stanu mieszadeł komór fermentacyjnych oczyszczalni ścieków Gdańsk-Wschod
PublicationDokonano oględzin i oceny stanu mieszadła zbiornika 15/3.
-
Opinia o innowacyjności - Wzrost konkurencyjności przedsiębiorstwa ZPHU TEMIROL poprzez zakup innowacyjnej maszyny do obróbki plastycznej blach
PublicationWykonano opinię o innowacyjności dotyczącą prasy krawędziowej TOSKAR EASYFAB 2600/120 wyposażonej w sterownik Next dedykowanej do precyzyjnego gięcia blach do grubości 6 mm
-
Opinia o innowacyjności; Wdrożenie technologii spawania stali duplex w połączonej metodzie rulonowej i swobodnego podparcia.
PublicationOpinia dotyczy nowego sposobu wykonania cylindrycznego zbiornika stalowego o dużych wymiarach, co stanowi ulepszenie znanej techniki wytwarzania zbiorników metodą podbudowy dolnych pierścieni od dachu w dół z zastosowaniem tzw. swobodnego podparcia.
-
Opór toczenia opon samochodowych
PublicationOpór toczenia opon samochodowych jest jednym z istotnych parametrów charakteryzujących współpracę opon samochodowych z nawierzchnią jezdni. jego wartość wpływa na zużycie paliwa a przez to na koszt transportu samochodowegooraz na osiągi pojazdów, takie jak prędkość maksymalna czy zdolność przyspieszania. W zależności od warunków ruchu zmniejszenie oporu toczenia o 10% powoduje zmniejszenie zużycia paliwa o2-4%. Zmniejszenie zużycia...
-
Outboard valve material testing
PublicationWykonano analizę przyczyn uszkodzenia korozyjnego zaworu zaburtowego. Sformułowano wnioski.
-
Pomiar naprężeń własnych metodą Barkhausena za pomocą sondy z wirującym polem magnetycznym
PublicationW pracy przedstawiono nowy sposób pomiaru naprężeń własnych w elementach konstrukcji z wykorzystaniem polowego efektu Barkhausena. Informację o stanie naprężeń uzyskano z analizy rozkładu kątowego natężenia efektu Barkhausena zmierzonego w sposób automatyczny poprzez sondę z wirującym polem magnetycznym. Przedstawiono zasadę działania i opis układu pomiarowego oraz przykłady wykorzystania tej metody w ocenie stanu naprężenia w...
-
Pomiary ilości wodoru dyfundującego w stopiwie elektrod celulozowych i zasadowych
PublicationW artykule scharakteryzowano technologię wytwarzania złączy poprzecznych rurociągów energetycznych w aspekcie kontroli ilości wodoru dyfundującego. Oznaczono zawartość wodoru dyfundującego w stopiwie dla złączy wielościegowych wykonanych elektrodami o otulinie celulozowej i zasadowej. Ustalono, że po wykonaniu 4 ściegów ilość wodoru dyfundującego spada z około 40 ml/100 g do poziomu 12 ml/100 g i zaproponowano wyjaśnienie mechanizmów...
-
Porównanie zużycia ściernego wybranych biomateriałów przeznaczonych na komponenty ślizgowe endoprotez stawu biodrowego
PublicationNadrzędnym wymaganiem stawianym nowoczesnym endoprotezom jest wysoka trwałość współpracujących elementów, przekładająca się na optymalnie długi czas funkcjonowania w organizmie ludzkim. Niestety trwałość obecnie stosowanych endoprotez stawu biodrowego ograniczona jest procesami zużycia tribologicznego, zachodzącymi w podstawowym układzie ruchowym pomiędzy głową, a panewką zaimplantowanej endoprotezy stawu biodrowego [Pawlak i in....
-
Preliminary studies of seamless flux cored wires stored in extreme conditions
PublicationIn the paper preliminary experimental studies of flux cored wires moisturized under controlled conditions are described. Three seamless wires of different grades have been placed in environmental chamber and moisturized in extremely adverse conditions (temperature T = 60° C, relative humidity H = 90%) for 240 hours. During this time measurements of weight gain and observations of surface of wires have been carried out. Also diffusible...
-
PROBLEMY SPAWANIA PODWODNEGO STALI O PODWYŻSZONEJ WYTRZYMAŁOŚCI
PublicationW artykule scharakteryzowano obecnie stosowane techniki spawania podwodnego oraz problemy związane z uzyskiwaniem złączy o wymaganych własnościach. Przedstawiono wyniki badań spawalności stali o podwyższonej wytrzymałości w warunkach podwodnych. Wskazano główne kierunki badawcze oraz rozwój technologii spawalniczych zmierzających do ograniczenia wpływu niekorzystnych warunków spawania podwodnego oraz poprawy jakości złączy wykonywanych...
-
Progress in the post weld residual stress evaluation using Barkhausen effect meter with a novel rotating magnetic field probe
PublicationWe report the progress in post weld residual stress evaluation using Barkhausen effect (BE) meter with rotating magnetic field probe. The novel probe of the BE meter contains two C-core electromagnets and searching coil with ferrite antenna. This meter allows automatic measurements of BE intensity envelopes at different angles of magnetizing field. The full process of measurement at given position of the probe takes about only...
-
Raport z badań materiałowych rurociągu instalacji wody chłodzącej hydrozespołu HZ-4 z Elektrowni Wodnej Żarnowiec
PublicationWykonano badania materiałowe fragmentów rurociągów instalacji wody chłodzącej hydrozespołu. Zakres pracy obejmował analizę chemiczną stali rurociągu, badania makroskopowych uszkodzeń rurociągu, badania EDX osadów i produktów korozji występujących na powierzchni wewnętrznej rurociągu, badania mikroskopowe uszkodzeń i oceny stanu rurociągu
-
Raport z badań rury króćca N1 z reaktora 150-R1 Grupa LOTOS S.A
PublicationPrzedmiotem pracy było przeprowadzenie badań materiałowych rury króćca fi 367,6 mm z reaktora 150. Celem badań było ustalenie stanu materiału po eksploatacji