Search
Division Of Structural Materials Technology And Welding
Publications
Filters
total: 59
Catalog Publications
Year 2025
-
Characteristics of AISI 420 And AISI 301 Stainless Steels Coatings Obtained by Thermal Spraying
PublicationIn this study, AISI 301 and AISI 420 stainless steels were deposited on an AISI 4135 substrate using the wire arc spray process (WASP). X-ray spectrum analysis revealed the presence of a body centred cubic (bcc) structure in both coatings. In particular, the AISI 301 coating showed the additional identification of chromium carbide Cr7C3. Conversely, the AISI 420 coating manifested the presence of a body centred cubic (Fe, Cr) structure,...
-
Microstructure degradation and creep failure study of the dissimilar metal welded joint of heat-resistant steel and Inconel 617 alloy tested at 650 °C and applied stress range of 100–150 MPa
PublicationThe advanced ultra-supercritical (A-USC) power plant system is anticipated to become India's next-generation base-load power station. To adopt AUSC technology, dissimilar welded joints (DWJs) between heat-resistant steels and the nickel-based alloys, using the nickel-based fillers, will need to be implemented. However, failure of dissimilar welded joints from P92 steel base metal or the heat affected zone (HAZ) has been commonly...
-
Pulsed current GTAW Inconel 625/AISI 304 L steel dissimilar joint: Microstructure and mechanical properties
PublicationThe present study aims to investigate the microstructure and mechanical behavior of Pulsed Current Gas Tungsten Arc Welded (PCGTAW) dissimilar joints of Inconel 625 and AISI 304 L steel. The dissimilar metal welded (DMW) joint was obtained using the Ni-based ERNiCrMo-3 filler. The welded joint was subjected to a microstructural study using optical microscopy and Scanning electron microscopy (SEM) with energy dispersive X-Ray...
-
Pulsed GTAW joint of P92 steel and Inconel 625: microstructure and mechanical properties
PublicationIn the present work, the relationship between microstructure and mechanical properties has been investigated for the dissimilar welded joint of P92 steel and Inconel 625, fabricated using the pulsed current gas tungsten arc welding (GTAW) process. Microstructural investigation revealed that the pulsed current resulted in fner equiaxed dendrites in the bulk weld metal, while columnar dendrites were observed in the weld metal near...
-
The influence of selected metal oxides and laser modification on the surfaces of titanium alloys – Bibliometric and systematic review
PublicationManufacturing of oxide coatings (ZnO, ZrO2 , CuO) and laser processing are methods for modifying the surface of titanium and its alloys. It is particularly useful in implantology, where these techniques allow for proper connection of the implant to human tissue. The article consists of two complementary parts: a bibliographic review and a literature survey. The results of a bibliographic analysis conducted for a set of 429 publications...
Year 2024
-
A dissimilar welded joint of grade 92 steel and AISI 304L steel obtained using IN82 buttering and IN617 fller: relationship of microstructure and mechanical properties
PublicationUnfavourable operating conditions of equipment in the energy industry resulting from high-temperature loads determine the need to use special materials and technological solutions, including welding procedures. In this article, buttering using IN82 (ERNiCr-3) consumables was proposed as a method to improve the weldability of grade 92 steel joined by the gas tungsten arc welding (GTAW) process with AISI 304L (IN617 fller). The...
-
Activated Tungsten Inert Gas Weld Characteristics of P91 Joint for Advanced Ultra Supercritical Power Plant Applications
PublicationActivated Tungsten Inert Gas (A-TIG) welding, a variant of tungsten inert gas (TIG) welding, was used for welding P91. In Generation IV power plants, P91 welds are prone to premature failure due to the presence and formation of brittle phases and creep at high temperatures. When performing A-TIG welding, the flux composition plays a role in the reversal of the Marangoni flow in the weld pool, which ultimately determines the level...
-
Advanced ultra super critical power plants: role of buttering layer
PublicationDissimilar metal welded (DMW) joint plays a crucial role in constructing and maintaining ultra-supercritical (USC) nuclear power plants while presenting noteworthy environmental implications. This research examines different welding techniques utilized in DMWJ, specifically emphasizing materials such as P91. The study investigates the mechanical properties of these materials, the impact of alloying elements, the notable difficulties...
-
Corrosion performance of super duplex stainless steel and pipeline steel dissimilar welded joints: a comprehensive investigation for marine structures
PublicationThis study investigates the corrosion behavior of dissimilar gas tungsten arc (GTA) welded joints between super duplex stainless steel (sDSS 2507) and pipeline steel (X-70) using electrochemical and immersion corrosion tests. The GTA welds were fabricated using ER2594 and ER309L fller metals. The study examined the electrochemical characteristics and continuous corrosion behavior of samples extracted from various zones of the weldments...
-
Creep rupture study of dissimilar welded joints of P92 and 304L steels
PublicationThe present work investigates the high-temperature tensile and creep properties of the dissimilar metal weld joints of 304L austenitic stainless steel (SS) and P92 creep strength-enhanced ferritic-martensitic (CSEF/M) steel under diferent testing condition. Thermanit MTS 616 fller rod (P92 fller) and the multi-pass tungsten inert gas (TIG) welding process were used to create the dissimilar weld connection. The ultimate tensile...
-
Effect of underwater friction stir welding parameters on AA5754 alloy joints: experimental studies
PublicationThe water as a welding environment may generate serious technological and metallurgical problems but in certain cases, the physicochemical properties of water can be used effectively, e.g., to impart the specific properties of welded materials. The purpose of the work was verification of effectiveness of the water cooling of aluminium alloy AA5754 for various sets of technological parameters of underwater friction stir welding...
-
Effects of preheating on laser beam–welded NSSC 2120 lean duplex steel
PublicationDuplex stainless steels show sustainable alternative for the conventional austenitic grades, with higher strength, higher resistance against stress corrosion cracking, and lower purchase cost. Thus, duplex stainless steel gains more attention in construction, oil and gas, and chemical industries. Among duplex stainless steels, low nickel and low molybdenum alloyed lean duplex stainless steel are a cost-efective substitution of...
-
Enhanced Spectroscopic Insight into Acceptor-Modified Barium Strontium Titanate Thin Films Deposited via the Sol–Gel Method
PublicationIn the present paper, composite thin films of barium strontium titanate (BaxSr1−xTiO3) with an acceptor modifier (magnesium oxide—MgO) were deposited on metal substrates (stainless steel type) using the sol–gel method. The composite thin films feature BaxSr1−xTiO3 ferroelectric solid solution as the matrix and MgO linear dielectric as the reinforcement, with MgO concentrations ranging from 1 to 5 mol%. Following thermal treatment...
-
Exploring the trends in flux-cored arc welding: scientometric analysis approach
PublicationFlux-cored arc welding (FCAW) is a universal group of welding methods in terms of the scope of application and automation possibilities, the share of which in various industries in many countries is still increasing. The paper presents the results of bibliographic analyses (scientometric analysis with the use of VOSviewer, Bibliometrix and CitNetExplorer tools) of a data set of 993 publications indexed in the Web of Science database...
-
Microstructural evolution and mechanical behavior of activated tungsten inert gas welded joint between P91 steel and Incoloy 800HT
PublicationThis study examines the welded joint between P91 steel and Incoloy 800HT using the Activated Tungsten Inert Gas (A-TIG) welding process. The focus is on analyzing the microstructure and evaluating the mechanical properties of joints made with different compositions of activating flux. Owing to the reversal of the Marangoni effect in which the conventional direction of molten metal flow in the weld pool is reversed due to the application...
-
Microstructure and mechanical properties of a dissimilar metal welded joint of Inconel 617 and P92 steel with Inconel 82 buttering layer for AUSC boiler application
PublicationThe application of the novel dissimilar metal welded (DMW) joint, utilizing Inconel 617 and P92 steel, was showcased in the advanced ultra-supercritical (AUSC) boiler. The work has been performed to investigate the effect of Inconel 82 (ERNiCr-3) buttering layer on microstructure and mechanical properties (high-temperature tensile strength, impact strength and microhardness) of gas tungsten arc welded (GTAW) dissimilar joint between...
-
Operational Performance and Weld Bead Characteristics of Experimental Tubular-Wires for Underwater Welding
PublicationAiming to evaluate new formulations and their operational behavior underwater, two experimental tubular wires with different chemical compositions in their internal flux were initially manufactured, employing a pilot machine and a unique manufacturing process. Weld beads were deposited on a plate placed in a flat position inside a tank using a mechanized system and the IMC 300 welding power source. The work was done at a depth...
-
Role of buttering layer composition on microstructural heterogeneity and mechanical properties of Alloy 617 and P92 steel dissimilar welded joints for future Indian AUSC program
PublicationRestrictive operating conditions (even exceeding 700 °C) of materials in advanced ultra super critical (AUSC) power plants and the need to minimize manufacturing and maintenance costs require the production of dissimilar metal welded joints (DMW). Significant differences in the physical and chemical properties of welded materials lead to phenomena that reduce the weldability of the metals used and force the search for solutions...
-
Storage of High-Strength Steel Flux-Cored Welding Wires in Urbanized Areas
PublicationThe condition of the consumables is a key factor determining the waste reduction in the welding processes and the quality of the welded joint. The paper presents the results of tests of four types of fux-cored wires dedicated for welding high-strength steels, stored for 1 month and 6 months in Poland in two urbanized areas: in a large seaside city (Gdańsk) and in Warsaw, located in the center of the country. The wires were subjected...
-
The Use of Cluster Analysis to Assess the Wear Resistance of Cermet Coatings Sprayed by High Velocity Oxy-Fuel on Magnesium Alloy Substrate
PublicationCermet coatings are one of the best surface protection of machine elements against wear. On the other hand, the most universal and economically justified method of applying such coatings is high velocity oxy-fuel (HVOF) spraying. This method makes it possible to produce coatings characterized by compact structure, low porosity and very good adhesion to the substrate. All these fundamental properties contribute to the high wear...
Year 2023
-
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublicationThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Determination of t8/5 cooling times for underwater local dry welding of steel
PublicationKnowledge of thermal history is the basic condition for studying the structure - properties of welded joints. The determinant of thermal history is the thermal cycle, whose in-situ measurements are still a big challenge. Water as the welding environment complicates this issue even more. The article presents a method to determine an equation for calculating t8/5 cooling times for underwater gas metal arc welding of unalloyed steels...
-
Dissimilar autogenous TIG joint of Alloy 617 and AISI 304H steel for AUSC application
PublicationTo reduce costs and improve high-temperature performance in Advanced Ultra Super Critical (AUSC) boilers, it is necessary to weld austenitic steel to Inconel alloy. In this study, the autogenous tungsten inert gas (TIG) welding process was used to join Alloy 617 and an austenitic AISI 304H steel plate of thickness 5 mm. Microstructural analysis showed that the microstructure formation was uneven along the weldments, with columnar...
-
Effect of Arc Strikes on High Strength Low Alloy Steels Welded by SMAW
PublicationWet welding with covered electrodes (Shielded Metal Arc Welding – SMAW) is the most commonly used method of carrying out welding repair works in a water environment. Limited visibility and the inability to move freely under water result in an increased risk of formation of welding imperfections such as lack of fusion, lack of penetration and arc strikes. The work focused on changes in the properties and structure of steel subjected...
-
Effect of water salinity on properties of multipass underwater wet manual metal arc welded joints
PublicationThe weldability of steel under the water is limited due to the influence of the environment. Water causes limited visibility, presence of the residual stresses, increasing the cooling rate, and increasing the diffusible hydrogen content in deposited metal, leading to the formation of brittle microstructures in heat-affected zone (HAZ). The paper presents the results of mechanical properties testing of S420G2+M steel welded joints...
-
Effects of Storing Flux-Cored Wires under Various Conditions
PublicationWelding processes involving the use of flux-cored wires are becoming increasingly popular, particularly in shipbuilding as well as in off-shore and civil engineering. The article presents characteristics of the welding process, its areas of application as well as advantages and disadvantages (e.g. necessity of ensuring appropriate conditions for the storage of filler metal wires). The satisfaction of quality-related requirements...
-
Friction Stir Welding of Aluminum in the Aerospace Industry: The Current Progress and State-of-the-Art Review
PublicationThe use of the friction stir welding (FSW) process as a relatively new solid-state welding technology in the aerospace industry has pushed forward several developments in different related aspects of this strategic industry. In terms of the FSW process itself, due to the geometric limitations involved in the conventional FSW process, many variants have been required over time to suit the different types of geometries and structures,...
-
High-Temperature Tensile Behaviour of GTAW Joints of P92 Steel and Alloy 617 for Two Different Fillers
PublicationThis study explores the high-temperature (HT) tensile rupture characteristics of a dissimilar gas-tungsten-arc-welded (GTAW) joint between P92 steel and Alloy 617, fabricated using ER62SB9 and ERNiCrCoMo-1 fillers. The high-temperature tensile tests were performed at elevated temperatures of 550 ◦C and 650 ◦C. An optical microscope (OM) and a field emission scanning electron microscope (FESEM) were utilized to characterize the...
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublicationThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...
-
Investigating the Effects of Geometrical Parameters of Re-Entrant Cells of Aluminum 7075-T651 Auxetic Structures on Fatigue Life
PublicationIn this study, the effects of two geometrical parameters of the re-entrant auxetic cells, namely, internal cell angle (θ) and H/L ratio in which H is the cell height, and L is the cell length, have been studied on the variations of Poisson’s ratio and fatigue life of Aluminum 7075-T6 auxetic structures. Five different values of both the H/L ratio and angle θ were selected. Numerical simulations and fatigue life predictions have...
-
Investigation on polypropylene friction stir joint: effects of tool tilt angle on heat flux, material flow and defect formation
PublicationTool tilt angle (TTA) is a critical factor that can control material flow in polymeric materials' friction stir joining (FSJ). This study selected a TTA range between 0° to 4° for FSJ of polypropylene (PP) polymer sheet. A modified computational fluid dynamic (CFD) technique was implemented to gain a deep understanding of the effects of TTA during FSJ of PP. The PP joint's internal flow, defect formation, heat generation, and tensile...
-
Kinetics of Intermetallic Phase Precipitation in Manual Metal Arc Welded Duplex Stainless Steels
PublicationThe article presents the influence of heat treatment on the kinetics of transformations in lean duplex LDX2101 steel and a weld made of standard duplex 2209 material, which was welded by manual metal arc welding. Changes in the microstructure, hardness, and magnetic phase content were analyzed after heat treatment was conducted at a temperature of 800 °C for a period ranging from 15 to 1440 min. Light and scanning microscopy, Vickers...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublicationThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study
PublicationTwo types of the weld joint of Inconel 617 alloy were produced using gas tungsten arc welding (GTAW) and shielded metal arc welding (SMAW) processes with ERNiCrCoMo-1 filler metal and ENiCrCoMo-1 electrode, respectively. The weld metal showed the segregation of the principle alloying elements like Mo and Cr along the inter-dendritic spaces, triggering the formation of secondary phases. The microstructure characterization of the...
-
Microstructure and Mechanical Properties of Combined GTAW and SMAW Dissimilar Welded Joints between Inconel 718 and 304L Austenitic Stainless Steel
PublicationA dissimilar welded joint of Inconel 718 and 304L austenitic stainless steel was prepared using a combined procedure with the gas tungsten arc welding and shielded metal arc welding processes by employing the Ni-based fillers: ERNiCr-3 and ENiCrFe-3. The welded joints were investigated for metallographic testing and mechanical properties, and a relationship was established between the microstructure and the resultant mechanical...
-
P92 steel and inconel 617 alloy welds joint produced using ERNiCr-3 filler with GTAW process: Solidification mechanism, microstructure, mechanical properties and residual stresses
PublicationThe objective of the current study was to analyse the microstructure, mechanical characteristics, and residual stresses of a dissimilar welded joint (DWJ) made of P92 steel and the Inconel alloy 617 (IN617) using the gas tungsten arc welding (GTAW) method. The ERNiCr-3 filler was selected to produce the conventional V groove (VG) and narrow V groove (NVG) butt joint. The filler deficient zones in the weldments, such as the filler...
-
Review on friction stir welding of dissimilar magnesium and aluminum alloys: Scientometric analysis and strategies for achieving high-quality joints
PublicationMagnesium and aluminum alloys continually attract interest as lightweight structural materials for transport applications. However, joining these dissimilar alloys is very challenging. The main obstacle that hinders progress in dissimilar Mg-Al joining is the formation of brittle intermetallic compounds (IMCs). As a solid-state joining technique, FSW is an excellent candidate to attenuate the deleterious IMC effects in dissimilar...
-
Selection of Electrode Material for Inconel 617/P92 Steel SMAW Dissimilar Welds
PublicationThe present work aimed to investigate the microstructure and mechanical properties of the dissimilar shielded metal arc welded (SMAW) joint of Alloy 617 and P92 steel for advanced ultrasupercritical boilers. The SMAW joint was produced using three different types of electrodes, namely, ENiCrFe-3, ENiCrMo-3, and ENiCrCoMo-1. During microstructural observation of the welded joints, no possible cracking was detected in the weldments....
-
Study on Microstructure-Property Relationship of Inconel 617 Alloy/304L SS Steel Dissimilar Welds Joint
PublicationWelding of Inconel 617 (IN617) alloy and austenitic 304L SS steel has been attempted using the autogenous Laser Beam Welding (LBW) process. Characterization of dissimilar weldments was performed on either side of the fusion boundaries. The metallographic results showed that the inhomogeneous microstructure formation for weld metal contained columnar and cellular dendrites near the interface, whilst the columnar, cellular and equiaxed...
-
Technologies for Joining and Forming Thin-Walled Structures in the Construction of Transportation Vehicles
PublicationEditorial
-
The Application of Cluster Analysis in the Assessment of the Weldability of Unalloyed Steels
PublicationNon-alloy steels constitute a large group of steels characterised by diversified chemical composition, structural morphology and a wide range of mechanical properties (determining weldability). The paper presents results of multidimensional analyses (based on cluster analysis) of 110 selected unalloyed steel grades. Properties adopted as diagnostic features included the chemical composition, mechanical properties (yield point)...
-
Wpływ niezgodności spawalniczych typu ślad zajarzania łuku na strukturę i twardość stali T24
PublicationW pracy opisano badania eksperymentalne dotyczące oceny wpływu cyklu cieplnego podczas tworzenia się niezgodności spawalniczych typu ślady zajarzania łuku na właściwości i strukturę stali T24. Ujawniono wpływ suszenia elektrod na wielkość strefy utlenienia oraz wpływ natężenia prądu spawania na wielkość wykonanego śladu zajarzenia łuku. Przedstawione wyniki badań potwierdzają konieczność wykrywania i usuwania śladów zajarzania...
Year 2022
-
Advancements in the Additive Manufacturing of Magnesium and Aluminum Alloys through Laser-Based Approach
PublicationComplex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives such as reduced part numbers, greater functionality, and lightweight, among others. Polymers, metals, and ceramics are the few materials that can be used in AM technology, but metallic materials (Magnesium and Aluminum) are attracting more attention from the research and industrial point of view. Understanding the role...
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublicationIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
BADANIA JAKOŚCI BEZSZWOWYCH DRUTÓW PROSZKOWYCH
PublicationProces spawania drutami proszkowymi (FCAW) zyskuje coraz większą popularność w różnych dziedzinach przemysłu. Przemysł stoczniowy oraz offshore znacznie częściej wykorzystuje tę metodę przy wykonywaniu odpowiedzialnych i masywnych konstrukcji, których nie można wykonać stosując metody w pełni zautomatyzowane, np. spawanie łukiem krytym. Wzrost zainteresowania tą metodą spowodowany jest przez wysoką wydajność procesu spawania, łatwość...
-
Badania nieniszczące czopów łopatek turbiny Hz3 EW Straszyn na obecność pęknięć nieciągłości
PublicationCelem badań była identyfikacja wad materiałowych na czopach łopatek Hz3 w turbinie Kaplana , na podstawie następujących badań: - wizualnych (VT), - magnetyczno proszkowych (MT), ultradźwiękowych. Na podstawie w/w badań poszczególnych stref pomiarowych, dokonano oceny wadliwości materiału 4 czopów łopatek, łączących łopatki z wieńcem Hz3, z punktu widzenia inicjacji pęknięć. Wynik badań przekazano Zleceniodawcy.
-
Deformable model of a butterfly in motion on the example of Attacus atlas
PublicationInsect wings can undergo significant chordwise (camber) as well as spanwise (twist) deformation during flapping flight but the effect of these deformations is not well understood. The shape and size of butterfly wings leads to particularly large wing deformations, making them an ideal test case for investigation of these effects. High-speed videogrammetry was used to capture the wing kinematics and deformations. The movements of...
-
Effect of Tool Positioning Factors on the Strength of Dissimilar Friction Stir Welded Joints of AA7075-T6 and AA6061-T6
PublicationFriction Stir Welding (FSW) is a solid-state bonding technique. There are many direct and indirect factors affecting the mechanical and microstructural properties of the FSW joints. Tool offset, tilt angle, and plunge depth are determinative tool positioning in the FSW process. Investigating the effect of these factors simultaneously with other parameters such as process speeds (rotational speed and translational speed) and tool...
-
Effects of Noncontact Shoulder Tool Velocities on Friction Stir Joining of Polyamide 6 (PA6)
PublicationIn this study, the effects of the traverse and rotational velocities of the noncontact shoulder tool on the heat generation and heated flux during the friction stir joining of high-density polyamide 6 (PA6) polymer were investigated. The computational fluid dynamics (CFD) method was employed to simulate the thermomechanical phenomena during the friction stir joining (FSJ) process of PA6. A developed model was used to consider the...
-
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublicationThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...