Search
Filters
total: 100
filtered: 97
-
Catalog
Chosen catalog filters
Search results for: HOMOGENEUS AND HETROGENEOUS CONDENSATION
-
COMPARISON OF TWO MODELS OF CONDENSATION
PublicationIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages. At least last two stages of this part of turbines operate in two –phase region. The liquid phase in this region in mainly created in the process of homogeneous and heterogeneous condensation. Several observations confirm however, that condensation often occurs earlier than it is predicted by theory i.e. before the...
-
Estimation of the steam condensation flow via CFD methods
PublicationThe results of numerical simulations to predict the performance of different steam models have been presented. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine stage. For numerical analysis three models have been finally used – the ideal steam model without condensation, an equilibrium steam...
-
„Eulerian – Eulerian” versus ,,Eulerian –Lagrangean” models of condensation
PublicationLiquid phase in the flowing vapor through stages of the steam turbine is the cause of a lot of failures. Nowadays, due to work of steam turbines at partial load, process of homogeneous and heterogeneous condensation still is current. The formation of drops of condensate under conditions other than nominal operation of turbine is a process still unknown. Engineers and designers involved in the development of power station machines...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symetrical phenomena. Their description however with a single correlation has yet to be suggested.In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the buble generetion is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such case...
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena, however their description with a single correlation has yet to be suggested. In the case of flow boiling in minichannels there is mostly encountered the annular flow structure, where the bubble generation is not present. Similar picture holds for the case of inside tube condensation, where annular flow structure predominates. In such...
-
Remarks on steam condensation modeling related to steam turbine large output
PublicationIn the paper numerical simulations have been performed to predict the performance of the diferent steam models. All of the considered models of steam condensation have been validated on the base of benchmark experiment employing expansion in nozzle and next on the low pressure part of the steam turbine equipped with the so-called Baumann stage. For numerical analysis three models have been finally used - the ideal steam model without...
-
Evaporation and condensation
PublicationW pracy przedstawiono encyklopedyczne ujęcie wrzenia i kondensacji.
-
Comparative study of flow condensation in conventional and small diameter tubes
PublicationIn the paper a method developed earlier by the first author is applied to calculations of heat transfer coefficient for inside tube condensation. The method has been verified using experimental data from literature on several fluids in different microchannels and compared to three well established correlations.
-
PRESSURE DROP OF HFE7000 AND HFE7100 IN FLOW CONDENSATION IN MINICHANNELS WITH ACCOUNT OF NON-ADIABATIC EFFECTS
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear stress acting between vapor phase and liquid...
-
Non-adiabatic Effects in Pressure Drop Calculations in Flow Boiling and Flow Condensation in Minichannels
PublicationConsiderations presented in the paper relate both to the case of flow boiling and flow condensation in conventional channels as well as small diameter ones. Authors devoted all the possible attention that the modeling presented is applicable to the whole range of quality variation in both cases of condensation and boiling. The form of two-phase flow multiplier, which is a major factor in modeling presented here, should be capable...
-
Determination of pressure drop in flow condensation of HFE7000 in minichannels with account of non-adiabatic effects
PublicationFlow boiling and flow condensation are often regarded as two opposite or symmetrical phenomena involving the change of phase. There is a temptation to describe both these phenomena with one only correlation, however such method has yet to be suggested. From amongst the structures present in flow boiling and flow condensation at least the annular flow structure seems to be mostly appropriate to the common modeling. However, the shear...
-
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublicationIn the paper the authors present investigations of flow condensation with the use of the HFE-7100 as a working fluid. The original and new approach to removing the heat from the channel was applied. The research was carried out using a wide-range real time observations, e.g. using infrared camera and stroboscope microphotography. This paper presents the details of experiment as well as the influence of heat and flow parameters...
-
Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels
PublicationAttention is focused on the issues of flow resistance and pressure drop of perspective refrigeration fluids during condensation in the two-phase flow in minichannels. The case of the flow through a cylindrical single channel of 2.3 mm inner diameter was carefully analyzed. Pressure drop tests have been performed in diabatic flow conditions. The effect of heat flux, mass flux, vapour quality and saturation temperature on the two-phase...
-
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublicationIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...
-
Numerical model for thin liquid film with evaporation and condensation on solid surfaces in systems with conjugated heat transfer
PublicationCondensation and evaporation processes from wetted surfaces are of utmost importance in many technological or industrial applications. In many devices such as home-appliances and air conditioning systems just to name a few, condensation and evaporation processes greatly impact their performance and energy efficiency; The physics of these processes is quite complex, involving conjugate heat transfer among solid–liquid film-gaseous...
-
A novel concept of enhanced direct-contact condensation of vapour- inert gas mixture in a spray ejector condenser
PublicationAn analytical model of direct steam condensation (DCC) in the novel idea of spray ejector condenser (SEC) in the presence of inert gas has been developed. It is based on continuity, momentum and energy equations for the steam-carbon dioxide mixture and direct contact condensation mechanisms due to heat transfer and concentration. Crucial in the process of DCC is atomisation of the motive fluid in the ejector. The effect of atomised...
-
Experimental investigations on pressure drop during the condensation in flow of HFE7000 in vertical minichannel
PublicationIn the work presented in the paper authors focused attention on the issues of flow resistance and pressure drop during condensation in the flow. The case of the descending flow through a cylindrical single-channel of 2.3 mm inner diameter was carefully analyzed. In the course of investigations a new working fluid HFE 7000 has been scrutinised which has a strongly differing properties in comparison to the other fluids that are commonly...
-
CO2 capture through direct-contact condensation in a spray ejector condenser and T- junction separator
PublicationThe design principle underlying the steam condensation and CO2 purification in a gas power plant with a focus on reducing CO2 emissions encompasses the deployment of a spray ejector condenser (SEC) and separator. This innovative system facilitates direct-contact condensation of steam with non-condensable gas (CO2) by inter acting with a spray of subcooled water, seamlessly integrated with a T-junction separator mechanism aimed...
-
Analytical model with non-adiabatic effects for pressure drop and heat transfer during boiling and condensation flows in conventional channels and minichannels
PublicationIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for boiling flow and condensation flow with account of non- adiabatic effects for some recent data collected from literature. The first effect, the modification of interface shear stresses in annular flow pattern is considered through incorporation of the so called "blowing parameter". The mechanism of...
-
Calculation method for flow boiling and flow condensation of R134a and R1234yf in conventional and small diameter channels
PublicationThe paper presents the results of calculations performed using the authors’ model to predict the heat transfer coefficient during flow boiling for two refrigerants R134a and R1234yf. The experimental data from various past studies have been collected and the calculations have been conducted for the full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house...
-
Direct-contact condensation from vapour- gas mixture in a spray ejector condenser for negative CO2 power plant
PublicationDirect-contact condensation of vapour containing the inert gas on a spray of subcooled liquid exists in a number of technical applications. For example, it may be found in the nuclear industry (e.g. pressurized jet under normal operating conditions, in safety analyses) or in the chemical industry (e.g. mixing-type heat exchanger, degasser, sea water desalting). The problem is also essential to modelling and analysis of some...
-
Non-isothermal effects in condensation inside tubes
PublicationWrzenie i kondensacja w przepływie są zjawiskami symetrycznymi, aczkolwiek ich opis za pomocą jednej korelacji w konfrontacji z eksperymentem nie dawał dobrych rezultatów. W pracy zmodyfikowano naprężenia styczne na granicy rozdziału faz w ten sposób, że uwzględniono wymianę pędu na granicy rozdziału faz i możliwym stała się adaptacja wcześniej zaproponowanego przez autorów modelu wrzenia w przepływie do obliczeń wymiany ciepła...
-
Experimental investigations on condensation in flow in small diameter channels
PublicationW pracy przedstawiono innowacyjne podejście do eksperymentalnych badań kondensacji w przepływie oraz omówiono wstępne wyniki badań eksperymentalnych kondensacji etanolu w pionowej rurce srebrnej o średnicy wewnętrznej 2.3 mm.
-
Heat and mass exchange in the process of condensation on critical droplets.
PublicationSformułowano model wzrostu kropli krytycznej podając równania zmiany masy i temperatury kropli. Pokazano formę zlinearyzowaną tych równań dobrze aproksymującą wzrost kropli w poblizu wymiaru krytycznego. Podano rozwiązanie układu zlinearyzowanego uzależniając zmianę temperatury od zmiany masy kropli i czasu charakterystycznego.
-
Multi-objective optimization of the ORC axial turbine for a waste heat recovery system working in two modes: cogeneration and condensation
PublicationDue to the demand of the district heating network and electric power grid ORC turbines can operate in the condensation and cogeneration modes. This approach requires the design of an expander which is characterized by high efficiency in each mode of operation. The paper is devoted to a multi-objective efficiency optimization of a one stage axial ORC turbine working on MM (Hexamethyldisiloxane). An Implicit Filtering algorithm (IF)...
-
Application of Feed Forward Neural Networks for Modeling of Heat Transfer Coefficient During Flow Condensation for Low and High Values of Saturation Temperatur
PublicationMost of the literature models for condensation heat transfer prediction are based on specific experimental parameters and are not general in nature for applications to fluids and non-experimental thermodynamic conditions. Nearly all correlations are created to predict data in normal HVAC conditions below 40°C. High temperature heat pumps operate at much higher parameters. This paper aims to create a general model for the calculation...
-
Controlling nodal displacement of pantographic structures using matrix condensation and interior-point optimization: A numerical and experimental study
PublicationThis study presents an innovative approach for the precise control of nodal displacements in pantographic structures. The method is founded on the Matrix Condensation of Force Method, seamlessly integrated with an Interior Point Optimization algorithm. This combination offers a unique advantage by allowing users to manipulate displaced nodes within a defined coordination domain. Furthermore, this approach introduces the Interior...
-
Experimental investigations on condensation in flow of HFE-7100 in small diameter channels
PublicationW pracy przedstawiono wyniki badań eksperymentalnych kondensacji czynnika HFE-7100 w minikanale o średnicy wewnętrznej 2.3 mm. Opisano również oryginalne podejście w prowadzeniu badań nad uzyskaniem lokalnych wartości współczynnika przejmowania ciepła podczas kondensacji w przepływie.
-
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublicationMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Catalytic aldol condensation of formaldehyde with acetic acid on titanium phosphates modified by different techniques
Publication -
Efficient method for Knoevenagel condensation in aqueous solution of amino acid ionic liquids (AAILs)
Publication -
Inert gas condensation made bimetallic FeCu nanoparticles - plasmonic response and magnetic ordering
Publication -
Thermal-hydraulic issues of flow boiling and condensation in organic Rankine cycle heat exchangers
PublicationW pracy przedstawiono szereg zagadnień cieplno-przepływowych podczas wrzenia i kondensacji w przepływie w wymiennikach ciepła obiegu ORC. Uwzględniono przemiany fazowe. Analizowano zagadnienia stabilności pracy wymienników oraz ich dynamikę
-
EXPERIMENTAL VERIFICATION OF THE METHOD OF FLOW BOILING AND FLOW CONDENSATION HEAT TRANSFER PREDICTION FOR SELECTED FLUIDS
PublicationIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of different refrigerants. The experimental data from various research studies from literature were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in- house developed model....
-
Early stages of condensation from the gaseous phase in a H2O-N2 system: a molecular dynamics study.
PublicationW pracy przedstawiono wyniki symulacji wczesnych etapów kondensacji z fazy gazowej w układzie xH2O (1-x)N2. Przeanalizowano całkowitą liczbę klastrów, średni rozmiar klastra i rozmiar klastra maksymalnego w funkcji czasu.
-
A common method for calculation of flow boiling and flow condensation heat transfer coefficients in minichannels with account of nonadiabatic effects
PublicationW pracy przedstawiono metodę ogólną wyznaczania współczynników przejmowania ciepła podczas wrzenia w przepływie i kondensacji w przepływie w minikanałach z uwzględnieniem efektu nieadiabatycznego. Uwzględnia ona wpływ modyfikacji naprężeń stycznych na granicy ciecz-para na wymianę ciepła.
-
Non-isothermal effects in a common method for calculation of heat transfer coefficient in flow boiling and flow condensation in minichannels
PublicationW pracy przestawiono efekty nieizotermiczne w metodzie wyznaczania współczynnika przejmowania ciepła podczas wrzenia w przepływie oraz kondensacji w przepływie w minikanałach. Wyniki obliczeń porównano z badaniami eksperymentalnymi z literatury, uzyskując dobrą zgodność.
-
Response to the queries raised by Dr M.M. Awad in a letter to editor comments on “Pressure drop of HFE7000 and HFE7100 during flow condensation in minichannels”
Publication.
-
Development of a spray-ejector condenser for the use in a negative CO2 emission gas power plant
PublicationOne promising solution for developing low-emission power technologies is using gaseous fuel combustion in pure oxygen when the exhaust gas mixture is composed of H2O and CO2, and where CO2 is separated after steam condensation. The paper presents the results of computational analyses providing to the Spray-Ejector Condenser (SEC) development, which is one of the crucial components of the negative CO2 gas power plant (nCO2PP) cycle...
-
Effect of the inclination angle of the condenser on the heat transfer coefficient value – experimental study
PublicationWhen considering problem of the condensation of the refrigerant in a flow inside channel, one needs to pay attention to the shape of its cross-section, the hydraulic diameter, the channel length as well as the orientation of the channel axis in space (horizontal, vertical, inclined). This paper presents an experimental study concerning the effect of the inclination angle of the condenser with a single coil pipe on the heat transfer...
-
CO2 capture using steam ejector condenser under electro hydrodynamic actuator with non-condensable gas and cyclone separator: A numerical study
PublicationThe concept for condensation of steam and CO2 separation in a negative CO2 emission gas power plant involves the utilization of a steam ejector condenser (SEC) for direct-contact condensation of vapor with inert gas (CO2) on a spray of subcooled liquid, integrated with a separator to produce pure CO2. Due to the increasing diffusion resistance and reduced convective heat transfer between the steam and subcooled water phases...
-
Synthesis of compounds with C-P-P and C=P-P bond systems based on the phospha-Wittig reaction
PublicationA reactivity study of a β-diketiminate titanium(III) phosphanylphosphido complex [MeNacNacTi(Cl){η2-P(SiMe3)-PtBu2}] (1) towards ketones such as benzophenone, 9-fluorenone, acetophenone, cyclopentanone, cyclohexanone and cycloheptanone is reported. The reactions of 1 with aromatic ketones (without α-protons) directly lead to the Ti(III) complex [MeNacNacTi(μ2-Cl)(OSiMe3)] (5) as well as Ti(IV) complexes with the pinacol condensation...
-
Comparative study of operation of condensing and traditional boilers equipped with the ORC module for electricity generation
PublicationCondensing technology applied to boilers is to make full use of thermal energy contained in the fuel. That means that additionaly the heat from condensation of exhaust gases can be used for the purposes of heating the domestic hot water and to cover the demand for central heating. The study analyzed the operation of the "traditional" boiler equipped with the ORC module as the similar arrangement but with the condensing boiler....
-
Applications of Alkanethiols in Organic Synthesis
PublicationThis manuscript is an update to the earlier Science of Synthesis contribution describing methods for the synthesis of alkanethiols. Thiols can be converted into sulfonic, sulfinic, sulfenic acid and their derivatives, sulfides, disulfides, polysulfides, sulfonium salts, and thiiranes, etc. These transformations are accomplished by nucleophilic displacement or addition, oxidation, condensation, or coupling reactions involving thiol...
-
Metal ion directed template synthesis using 2-acetyl-1,3-indandione and ethylenediamine: steric and electronic restrictions
PublicationA template synthesis using 2-acetyl-1,3-indandione and ethylenediamine results in formation of octahedral Ni complex, whose crystal structure has been resolved using single crystal X-ray diffraction. The structure indicates that only exocyclic enolic oxygen atom of the triketone takes part in the condensation with ethylenediamine.
-
High-efficient, zero-emission energy production
PublicationThis paper presents innovative thermodynamiccycles with high-efficient, zero-emission energy production. The main aim of this work is to show the role of nano-phenomena in the enhancement of the power of thermodynamic cycles. For that purpose, the cycles using oxy-combustion and spray ejected condensation are first studied and, secondly hybrid cycles using fuel cells and gas turbines are presented. The role of nano-phenomena in...
-
Analysis of cyclone separator solutions depending on SEC outlet conditions in nCO2PP
PublicationUtilization of spray ejector condenser in order to carry out direct-contact condensation of vapour with inert gas (CO2) on a spray of subcooled liquid integrated with separator (to make pure CO2) has been proposed for the task of condensation and CO2 separation in the negative CO2 emission gas power plant. Condensation and separation has a significant impact on the thermodynamic efficiency of the entire negative CO2 emission gas...
-
Giant Nernst effect in the incommensurate charge density wave state of P4W12O44
PublicationWe report the study of Nernst effect in quasi-low-dimensional tungsten bronze P4W12O44 showing a sequence of Peierls instabilities. We demonstrate that both condensation of the electronic carriers in the charge density wave state and the existence of high-mobility electrons and holes originating from the small pockets remaining in the incompletely nested Fermi surface give rise to a Nernst effect of a magnitude similar to that...
-
Efficient Method for the Synthesis of Functionalized Basic Maleimides
PublicationA three-step procedure involving Diels-Alder condensation of maleic anhydride with furane, formation of N-substituted imide upon reaction with appropriate diamine and a final retro Diels-Alder regeneration of the maleic carbon-carbon double bond is proposed for an unequivocal synthesis of N-substituted basic maleimides. The novel method is characterized by mild reaction conditions, easy work-up, high yields and no need for additional...
-
Alkanethiolates of Group 1,2, and 13-15 Metals
PublicationThis manuscript is an update to the earlier Science of Synthesis contribution describing methods for the synthesis of alkanethiolates of group 1, 2, and 13-15 metals. Alkanethiolates can be converted into S-alkyl thiocarboxylic acid esters, 1-thioglycosides, S-alkyl thiosulfinates, tetrahydro-1,4-thiazine-3-ones, sulfides, disulfides, sulfonium salts, dithioacetals and dithioketals, etc. These transformations are accomplished by...