Filters
total: 2359
filtered: 1911
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: Flash boiling
-
Investigation of R 22 and R 134a flow boiling in enhanced tubes
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła i spadków ciśnienia podczas wrzenia w przepływie R22 oraz R134a. Do badań użyto dwie rurki o rozwiniętej wewnętrznej powierzchni, tj. rurkę śrubowo-formowaną i rurkę niskożebrowaną oraz dwie rurki gładkie, jako rurki referencyjne. Eksperymenty przeprowadzono przy temperaturze nasycenia ok. zero stopni Celsjusza i końcowym stopniu suchości ok. 0.7. Wyniki badań eksperymentalnych...
-
Pool boiling of nanofluids on rough and porous coated tubes: experimental and correlation
PublicationThe paper deals with pool boiling of water-Al2O3 and water- Cu nanofluids on rough and porous coated horizontal tubes. Commercially available stainless steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate the test heater. The tube surface was roughed with emery paper 360 or polished with abrasive compound. Aluminium porous coatings of 0.15 mm thick with porosity of about 40% were produced by...
-
Design analysis of Tesla micro-turbine operating on a low-boiling medium
PublicationThis paper presents results of the design analysis of a Tesla bladeless turbine intended for a co-generating micro-power plantof heat capacity 20 kW, which operates in an organic Rankine cycle on a low-boiling medium. Numerical calculations of flowin several Tesla turbine models were performed for a range of design parameters. Results of investigations exhibit interestingfeatures in the distribution of flow parameters within the...
-
Pool boiling of water-Al2O3 nanofliud on horizontal porous coated tube
PublicationPrzedstawiono wyniki badań przejmowania ciepła podczas wrzenia w dużej objętości nanocieczy woda-Al2O3 na poziomej rurce z aluminiową powłoką porowatą o grubości 0.15 mm i porowatości 40%. Koncentracja nanocząstek wnosiła 0.01%, 0.1% oraz 1%. Niezależnie od koncentracji współczynnik przejmowania ciepła przy wrzeniu nanocieczy był niższy niż przy wrzeniu wody destylowanej.
-
Flow boiling intensification in minichannels by means of mechanical flow turbulising inserts
PublicationThe work presents the results of experimental investigation on heat transfer in minichannels. Refrigerant R123 was used as a test fluid. Single vertical silver tubes of 380 mm length and 2.3 mm diameter were examined with two variants of turbulising inserts. A wide range of parameters was considered, namely mass flux G=534-3011 kg/(m2s), heat flux qw=28.5-68.4 kW/m2, saturation temperature Tsat=23-86 stC and the full range of vapour...
-
Pressure drop and heat transfer during boiling and condensation at subcritical region
PublicationMost of the data presented in the literature relate to saturation temperatures in the range - 20°C to 40°C due to the application in refrigeration technology. There is necessity to extend databases to higher values of saturation temperature due to new applications such as Organic Rankine Cycle and high temperature heat pumps. Only few papers contain data for high reduced pressure for low boiling point liquids. This paper focus...
-
Experimental Investigations On The Momentum Pressure Drop During Flow Boiling Of R134a
PublicationThe article presents experimental investigations of the pressure drop during twophase flow. Experiments were performed for both adiabatic and heated flow of R134a. Obtained flow patterns were compared with the literature. Obtained data is used to validate momentum pressure drop predictions, a set of graphs showing comparisons, for a representative set of experimental conditions, of the two-phase frictional pressure gradients for...
-
Building a Nest by an Automaton
PublicationA robot modeled as a deterministic finite automaton has to build a structure from material available to it. The robot navigates in the infinite oriented grid $Z x Z$. Some cells of the grid are full (contain a brick) and others are empty. The subgraph of the grid induced by full cells, called the {\em field}, is initially connected. The (Manhattan) distance between the farthest cells of the field is called its {\em span}. The robot...
-
Experimental and theoretical study of flow boiling and dryout phenomenon of ethanol in vertical minitubes
PublicationW ramach przeprowadzonych prac zaadoptowano istniejące stanowisko do badań laminarnej konwekcji wymuszonej, wrzenia w przepływie oraz wysychania filmu cieczy na ściance kanału wykorzystując etanol jako płyn roboczy. Przeprowadzono systematyczne badania wrzenia w przepływie dla dwóch średnic rur, tj. 1.15mm i 2.3mm. W badaniach wykorzystano najnowsze osiągnięcia z zakresu technik termowizyjnych celem znalezienia dokładnej lokalizacji...
-
Pool boiling of water-Al2O3 and water-Cu nanofluids on horizontal smooth tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia dwóch nanocieczy woda-Al2O3 i woda Cu na poziomych gładkich rurkach stalowych i miedzianych. Koncentracja nanoicząstek wynosiła 0.01%, 0.1% oraz 1%.
-
Chapter 1. Modelling of temperature field of cylindrical pool boiling heating section
PublicationPoddano analizie fundamentalny problem określania temperatury powierzchni, na której zachodzi wrzenie. Rozpatrzono dwa przypadki ogrzewania sekcji: z zastosowaniem grzejnika patronowego oraz użyciem sekcji jako elementu oporowego. Sformułowano i rozwiązano zagadnienia brzegowe 1D, 2D ORAZ 3D. Przedstawiono wyniki obliczeń numerycznych z zastosowaniem MES.
-
Influence of pressure on heat transfer during pool boiling on smooth tube bundle
PublicationPrzedstawiono wyniki badań eksperymentalnych wrzenia wody, metanolu i R141b na pęu rur głądkich w warunkach podcisnienia i ciśnienia atmosferycznego
-
Horizontal flow boiling of R22, R134a and their mixtures with oil in smooth and enhanced tubes
PublicationOpisano stanowisko i procedurę badawczą. Przedstawiono wyniki badań wrzenia czynników R 22 i R 134a oraz ich mieszanin z olejem wewnątrz dwóch rur gładkich i dwóch rur o rozwiniętej powierzchni. Zweryfikowno wybrane korelacje współczynnika przejmowania ciepła podczas wrzenia czystych czynników chłodniczych w rurach gładkich.
-
Modelling of temperature field of flat boiling section with active single nucleation site
PublicationZaprezentowano główne założenia wybranych modeli wrzenia dla pojedynczego centrum nukleacji. Przedstawiony model numeryczny dotyczy zagadnienia dwuwymiarowego, osiowo-symetrycznego, nieizotropowego przewodzenia ciepła dla warunków brzegowych pierwszego, drugiego i trzeciego rodzaju. Warunek brzegowy drugiego rodzaju reprezentuje gęstość strumienia ciepła połączoną z generacją pęcherzy z pojedynczego centrum nukleacji.
-
Influence of porous coating on heat transfer during R22 and R134a flow boiling.
PublicationPrzedstawiono wpływ powłoki porowatej na przenoszenie ciepła i spadku ciśnienia podczas wrzenia w przepływie czynników chłodniczych, R22 i R134a.
-
Flow boiling of R22, R134a and R 407C inside horizontal smooth tubes.
PublicationPrzedstawiono wyniki badań współczynnika przejmowania ciepła i spadku cisnienia podczas wrzenia czynników R22, R134a i R407C w rurach gładkich, wykonanych z miedzi i ze stali nierdzewnej.Opisano stanowisko i procedurę badawczą. Temperatura wrzenia wynosiła 0 st.C, stopień suchości na wlocie do odcinka pomiarowego był równy O, a na wylocie 0,7. Badania prowadzono w zakresie gestości strumienia masy od 250 do 500 kg/m2s. Zaobserwowano...
-
A simplified energy dissipation based model of heat transfer for subcooled flow boiling
PublicationIn the paper a model is presented based on energetic considerations for subcooled flow boiling heat transfer. The model is the extension of authors own model developed earlier for saturated flow boiling and condensation. In the former version of the model we used the heat transfer coefficient for the liquid single-phase as a reference level, due to the lack of the appropriate model for heat transfer coefficient for the subcooled...
-
Prediction of flow boiling heat transfer data for R134a, R600a and R290 in minichannels
PublicationIn the paper presented is the analysis of the results of calculations using a model to predict flow boiling of refrigerants such as R134a, R600a and R290. The latter two fluids were not used in development of model semiempirical correction. For that reason the model was verified with present experimental data. The experimental research was conducted for a full range of quality variation and a relatively wide range of mass velocity....
-
Pool boiling of water-Al2O3 and water-Cu nanofluids on horizontal smooth tubes
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia dwóch nanocieczy, tj. woda-Al2O3 i woda-Cu o trzech koncentracjach masowych nanocząstek: 0.01%,0.1% oraz 1% na poziomych gładkich rurkach ze stali nierdzewnej i miedzi o średnicy zewnętrznej 10 mm.
-
An improved method for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the paper are presented the results using the authors own model to predict heat transfer coefficient during flow boiling. The model has been tested against a large selection of experimental data to investigate the sensitivity of the in-house developed model. In the work are presented the results of calculations obtained using the semi-empirical model on selected experimental flow boiling data of the refrigerants: R134a, R1234yf,...
-
Modelling study of flow boiling heat transfer of perspective fluids for refrigeration technology
PublicationThere is a gap of knowledge on flow boiling at high saturation temperatures and higher values of reduced pressure. Thus far, the in-house developed semi-empirical model for flow boiling and flow condensation showed a satisfactory accuracy for calculations for various refrigeration fluids for a wide scope of reduced pressures. This study presents results of calculations of heat transfer coefficient of perspective refrigeration fluids,...
-
The effect of reduced pressure on carbon dioxide flow boiling heat transfer in minichannels
Publication. In the paper presented are the results of the study on the effect of reduced pressure on flow boiling heat transfer data in minichannels as well as conventional ones. That effect renders that most of heat transfer correlations fail to return appropriate results of predictions. Mostly they have been developed for the reduced pressures from the range 0.1-0.3. The special correction has been postulated to the in-house model of flow...
-
Thermal performance of a prototype plate heat exchanger with minichannels under boiling conditions
PublicationTo solve the problem and to meet the requirements of customers in the field of high heat fluxes transfer in compact units, a new design of plate heat exchanger with minichannels (minichannels PHE) was proposed. The aim was to construct a compact heat exchanger of high effectiveness for the purpose of household cogeneration ORC system. In this paper the experimental analysis of an assembled prototype of such compact heat exchanger...
-
Accurate rolling resistance Rolling resistance measurements can be influenced by a number of factors
PublicationTire rolling resistance is one of the most difficult-to-measure parameters of the tire/ pavement interface, especially if road measurements are required. First of all, it is necessary to measure a fairly small force in the system that is heavily loaded by other forces and subjected to many adverse effects causing measurement errors. The second problem is related to the fact that tire rolling resistance depends on many factors,...
-
Daylight recommendation for building interiors in the selected national building and lighting regulations in the EU
PublicationThe quality of life within building environment is closely linked to the quality of daylight effectively delivered into the living space. The paper describes the results of the normative documents review and a comparative analysis, based on which daylight recommendations present in national regulations have been compiled.
-
Phenolic Acid Content and Antioxidant Properties of Edible Potato (Solanum tuberosum L.) with Various Tuber Flesh Colours
Publication -
Circumferential temperature distribution during pool boiling of R 141b onhorizontal modified tubes.
PublicationZaproponowano własną bierną, metodę intensyfikacji przejmowania ciepła w obszarze górnej tworzącej rurki w celu zminimalizowania obwodowego rozkładu temperatury. Metoda polega na naniesieniu aluminiowej warstwy porowatej tylko na części powierzchni rurki - właśnie w obszarze górnej tworzącej.
-
Influence of porous coating on heat transfer during flow boiling of R22, R134a and R407C
PublicationPrzedstawiono wpływ pwłoki porowatej w pozionej rurce podczas wrzenia w przepływie i spadku ciśnienia czynników chłodniczych R22, R134a i R407C.
-
Pool Boiling of Water–Al2O3 and Water–Cu Nanofluids Outside Porous Coated Tubes
PublicationThis paper deals with pool boiling ofwater–Al2O3 and water–Cu nanofluids on porous coated, horizontal tubes. Commercially available stainless-steel tubes having 10 mm outside diameter and 0.6 mm wall thickness were used to fabricate a test heater. Aluminum porous coatings 0.15 mm thick with porosity of about 40% were produced by plasma spraying. A smooth tube served as a reference tube. The experiments were conducted under different...
-
The effect of boiling in a thermosyphon on surface tension and contact angle of silica and graphene oxide nanofluids
Publication -
A new procedure for the determination of distillation temperature distribution of high-boiling petroleum products and fractions
PublicationThe distribution of distillation temperatures of liquid and semi-fluid products, including petroleum fractions and products, is an important process and practical parameter. It provides information on properties of crude oil and content of particular fractions, classified on the basis of their boiling points, as well as the optimum conditions of atmospheric or vacuum distillation. At present, the distribution of distillation temperatures...
-
Nucleate pool boiling heat transfer from small horizontal smooth tube bundles
PublicationPrzedstawiono wyniki pomiarów współczynnika przejmowania ciepła podczas wrzenia wody destylowanej, metanolu i R141b na poziomym pęku rur gładkich, który składał się z 19 rurek, ogrzewanych elektrycznie, w układzie przestawionym i podziałce 1.7d oraz 2.0d. Wyznaczono również wartości współczynnika wpływu pęku. Podano równanie korelacyjne do obliczania średniego współczynnika przejmowania ciepła
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublicationIn the paper are presented the results of calculations using authors own model to predict heat transfer coefficient during flow boiling for carbon dioxide. The experimental data from various researches were scrutinised conducted for a full range of quality variation and wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The work shows the importance of taking into account surface...
-
Non-adiabatic Effects in Pressure Drop Calculations in Flow Boiling and Flow Condensation in Minichannels
PublicationConsiderations presented in the paper relate both to the case of flow boiling and flow condensation in conventional channels as well as small diameter ones. Authors devoted all the possible attention that the modeling presented is applicable to the whole range of quality variation in both cases of condensation and boiling. The form of two-phase flow multiplier, which is a major factor in modeling presented here, should be capable...
-
A semi-empirical model for flow boiling heat transfer with account of the reduced pressure effect
PublicationIn the present study the attention was focused on the influence of reduced pressure on the predictions of heat transfer during flow boiling at the extensive range of pressures. The results of calculations were to test the sensitivity of the in-house flow boiling model with respect to the selection of the appropriate two-phase flow multiplier, which is one of the distinctive elements of that model. For this purpose a few two-phase...
-
Experimental study and comparison with predictive methods for flow boiling heat transfer coefficient of HFE7000
PublicationThis article describes an experimental study of flow boiling of HFE7000 inside a smooth vertical channel. The investigation has been carried out in a circular stainless-steel tube with an inner diameter of 2.3 mm. The data have been collected for the applied heat fluxes q ranging from 61 to 205 kW/m2, the mass flux G ranging from 214 to 1006 kg/(m2 s), the saturation temperature Tsat ranging from 30 to 54 °C and the full range...
-
A simplified energy dissipation based model of heat transfer for post-dryout flow boiling
Publicationmodel for post dryout mist flow heat transfer is presented based on considerations of energy dissipation in the flow. The model is an extension of authors own model developed earlier for saturated and subcooled flow boiling. In the former version of the model the heat transfer coefficient for the liquid singlephase convection as a reference was used, due to the lack of the appropriate model for heat transfer coefficient for the...
-
Thermal-hydraulic issues of flow boiling and condensation in organic Rankine cycle heat exchangers
PublicationW pracy przedstawiono szereg zagadnień cieplno-przepływowych podczas wrzenia i kondensacji w przepływie w wymiennikach ciepła obiegu ORC. Uwzględniono przemiany fazowe. Analizowano zagadnienia stabilności pracy wymienników oraz ich dynamikę
-
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublicationDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Flow distribution and heat transfer in minigap and minichannel heat exchangers during flow boiling
PublicationThe topic of boiling heat transfer in miniscale geometries has focused the ever increasing interest of researchers in recent years. However, most of the works are related to mini- and microchannels and much less to minigaps. Meanwhile, minigaps allow for more comprehensive experimental studies, i.e. flow visualisations due to the flat, two-dimensional configuration of the flow. The results of the experimental investigations of...
-
Prediction of flow boiling heat transfer coefficient for carbon dioxide in minichannels and conventional channels
PublicationIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of carbon dioxide. The experimental data from various resea rches were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in-house model. The results show the importance of taking into...
-
Statistical Dynamics of the Rolling Mills
Publication -
Location of ship rolling axis.
PublicationPodano definicję osi kołysań statku i metodę określania jej położenia. Położenie osi zależy nie tylko od rozkładu mas statku ale równiez od tzw. ''mas towarzyszących'', które są reprezentacją sił hydrodynamicznych działających na statek w czasie kołysania. Podano proste formuły pozwalajace obliczyć poprawne położenie osi kołysań statku.
-
A new method for determination of flow boiling heat transfer coefficient in conventional diameter channels and minichannels
PublicationW pracy przedstawiono rozważania związane z modelowaniem wrzenia w przepływie w kanałach o średnicach konwencjonalnych, małych i minikanałach. Przedstawiono przegląd podejść do modelowania wymiany ciepła i w tym świetle przedstawiono oryginalne podejście autora. W przeciwieństwie do innych podejść metoda autora ma zastosowanie zarówno do kanałów o średnicach konwencjonalnych i minikanałach. Przedstawiono zadowalające porównania...
-
Circumferential temperature distribution during nucleate pool boiling outside smooth and modified horizontal tubes
PublicationPrzedstawiono wyniki badań eksperymentalnych obwodowego rozkłądu temperatury w poziomych rurkach, ogrzewanych elektrycznie na których zachodzi wrzenie pęcherzykowe. Wykazano, że lokalne - w obszarze górnej tworzącej rurki, zastosowanie powłki porowatej prowadzi do wygładzenia rozkładu temperatury oraz obniżenia średniej temperatury ścianki.
-
A semi-empirical method for calculation of heat transfer coefficient in flow boiling for conventional tubes and minichannels
PublicationW pracy przedstawiono zagadnienia które należy uwzględnić podczas modelowania wymiany ciepła z wrzeniem w przepływie w kanałach o małej średnicy. Uzyskano dobrą zgodność z wynikami badań eksperymentalnych.
-
Influence of wall temperature on heat transfer coefficient during R 22 boiling in microfin tube
PublicationPrzedstawiono wyniki badań współczynnika przejmowania ciepła i spadku ciśnienia podczas wrzenia czynnika R 22 w rurze nisko żebrowanej. Opisano stanowisko i procedurę badawczą. Zaobserwowano spadek współczynnika przejmowania. Opisano stanowisko i procedurę badawczą. Zaobserwowano spadek współczynnika przejmowania ciepła wraz ze wzrostem temperatury ścianki rury.
-
Effect of asymmetric fluid flow distribution on flow boiling in a microchannel heat sink – An experimental investigation
PublicationFlow boiling in microchannels is emerging as an exclusive cooling solution for miniaturized high-power electronic devices alongside having other high heat flux applications. Size miniaturization at microscale strangely increases heat transfer performance as well as flow boiling instabilities. Many flow boiling instabilities are interrelated and result from imperfect hydrodynamic conditions. One of such problems is flow maldistribution among...
-
A semi-empirical method for calculation of heat transfer coefficient in flow boiling for conventional tubes and minichannels
PublicationW pracy przedstawiono zagadnienia któe należy uwzględnić podczas modelowania wymiany ciepła z wrzeniem w przepływie w kanałach o małej średnicy. Uzyskano dobrą zgodność z wynikami badań eksperymentalnych.
-
Comparitive study of heat transfer and pressure drop during flow boiling and flow condensation in minichannels
PublicationIn the paper a method developed earlier by authors is applied to calculations of pressure drop and heat transfer coefficient for flow boiling and also flow condensation for some recent data collected from literature for such fluids as R404a, R600a, R290, R32,R134a, R1234yf and other. The modification of interface shear stresses between flow boiling and flow condensation in annular flow structure are considered through incorporation...