Search results for: WELDQN
-
INFLUENCE OF TACK WELDS DISTRIBUTION AND WELDING SEQUENCE ON THE ANGULAR DISTORTION OF TIG WELDED JOINT
PublicationIn this paper the influence of tack welds distribution and welding sequence on angular distortion of the Tungsten Inert Gas (TIG) welded joint was tested. Additionally, the effect of welding current on angular distortion was assessed. For research X2CrTiNb18 (AISI 441) stainless steel (2.5 mm thick) was chosen. During research specimens were prepared with different distributionsof tack...
-
Welding International
Journals -
Effect of welding conditions on susceptibility to cold cracking of underwater welded joints
PublicationPrzedstawiono wybrane aspekty spawalności stali przy spawaniu pod wodą metodą lokalnej komory suchej. Zwrócono szczególną uwagę na skłonność do tworzenia peknięć zimnych w SWC. Przy pomocy planowania doświadczeń określono ilościowy wpływ parametrów spawania na naprężenia krytyczne z próby implant.
-
The Effect of Welding Conditions on Mechanical Properties of Superduplex Stainless Steel Welded Joints
PublicationThe tests results of superduplex stainless steel welded joints made with a different heat input, using automatic submerged arc welding (SAW) and semi-automatic flux-cored arc welding (FCAW) have been presented. Metallographic examinations, the measurements of the ferrite content, the width of the heat affected zone (HAZ) and the hardness of the welds in characteristic areas have been performed. Significant differences in the amount of...
-
Welding Technology Review
Journals -
Investigation of Mechanical and Microstructural Properties of Welded Specimens of AA6061-T6 Alloy with Friction Stir Welding and Parallel Friction Stir Welding Methods
PublicationThe present study investigates the effect of two parameters of process type and tool offset on tensile, microhardness, and microstructure properties of AA6061-T6 aluminum alloy joints. Three methods of Friction Stir Welding (FSW), Advancing Parallel-Friction Stir Welding (AP-FSW), and Retreating Parallel-Friction Stir Welding (RP-FSW) were used. In addition, four modes of 0.5, 1, 1.5, and 2 mm of tool offset were used in two welding...
-
Effect of Storage Conditions of Rutile Flux Cored Welding Wires on Properties of Welds
PublicationThe influence of storage locations of two grades of rutile flux cored welding wires on their surface condition and the strength of the welds made with them were studied. Wires were stored in real urban conditions (Gdańsk and Katowice) for 1 month, simultaneously recording changes in conditions: temperature and relative humidity of the environment. Visual tests of wires in the delivered and stored condition as well as visual and...
-
Manufacturing Parameters, Materials, and Welds Properties of Butt Friction Stir Welded Joints–Overview
PublicationThe modern and eco-friendly friction stir welding (FSW) method allows the combination of even such materials that are considered to be non-weldable. The development of FSW technology in recent years has allowed a rapid increase in the understanding of the mechanism of this process and made it possible to perform the first welding trials of modern polymeric and composite materials, the joining of which was previously a challenge....
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublicationThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublicationThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
Angular welding distortion - one sided fillet weld
Open Research DataWelding is the basic method of joining ship hull elements during its construction. However, this method of joining structural elements generates shrinks. Shrinks causes deformation of the entire welded structure, both linear and angular. In the shipbuilding industry, there is a tendency to oversize fillet welds, at the design as well as manufacturing...
-
Jacek Tomków dr hab. inż.
PeopleEducation:1. 2018 - Ph.D. of Technical Sciencesin field of Materials Engineeringthesis: Influence of underwater welding conditions on cold cracking of high strength low alloy steel 2. 2012 - Master of Science Engineer, Gdansk University of Technologyin the field of: Mechanical Engineeringwith specialization in: Manufacturing Engineering and Computer Aided Manufacturing Processesthesis: Non-destructive testing of welding joints...
-
WELDING JOURNAL
Journals -
On the Application of Magnetoacoustic Emission for a Nondestructive Assessment of the Post Welding Heat Treatment of High Chromium Steel Weld Seams
PublicationThe paper analyses the possibility of post weld heat treatment (PWHT) quality assessment with the help of magnetoacoustic emission (MAE) signal measurements. Two welded superheater tubes, made of high chromium VM12 steel, were analysed—as welded and heat treated one. The analysed sample in the as welded state exhibited significantly higher hardness, accompanied by a big difference in the MAE signal intensity (of order of about...
-
Temper bead welding of S460N steel in wet welding conditions
PublicationWet welding is the most common method of welding in water environment. It is most often used for repairing of underwater parts of offshore structures. However, the water as a welding environment causes an increase of susceptibility of steels to cold cracking. For underwater constructions high strength low alloy (HSLA) steel are widely used. In wet welding condition a HSLA steel is characterized by high susceptibility to cold cracking....
-
Temper bead welding of S420G2+M steel in water environment
PublicationThe article presents the idea of the use of Temper Bead Welding (TBW) technique to improve the weldability of high strength steel at underwater wet welding conditions. Wet welding method with the use of covered electrodes is described. This work shows results of metallographic examinations and hardness measurements of samples of S420G2+M steel with weld beads performed under water. It has been shown that Temper Bead Welding technique...
-
Advantages of the Application of the Temper Bead Welding Technique During Wet Welding
PublicationThermo-mechanically rolled S460ML steel was chosen for welding in underwater wet welding conditions by covered electrodes. The main aim of this study was to check the weldability for fillet welds in a water environment by controlled thermal severity (CTS) tests and to check the influence of temper bead welding (TBW) on the weldability of the investigated steel. Non-destructive and destructive tests showed that S460ML steel has...
-
Explosive welding of metals.
PublicationPrzedstawiono wytwarzanie i zastosowanie łączników zgrzewanych wybuchowo oraz wpływ podłoża na ten proces.
-
Underwater welding - a review
PublicationW artykule przedstawiono stan obecny oraz perspektywy rozwoju technik spawania pod wodą. Przeanalizowano najważniejsze problemy spawania w środowisku wodnym. Przedstawiono najważniejsze kierunki badań spawania podwodnego podejmowane w Katedrze Technologii Materiałów Maszynowych i Spawalnictwa Politechniki Gdańskiej
-
Role of bead sequence in underwater welding
PublicationThis paper presents examinations of the role of the bead sequence in underwater welding. Two specimens of wet welded layers made by covered electrodes with the use of normalized S355G10+N steel were welded by a reasonable bead sequence. For each specimen, metallographic macro- and micro-scopic tests were done. Then, Vickers HV10 hardness measurements were conducted for each pad weld in the welded layer. The results show that welding...
-
Influence of Parameters of Laser Beam Welding on Structure of 2205 Duplex Stainless Steel
PublicationLaser welding is used in modern industry, having many advantages comparing to traditional welding technologies. Nowadays, industry sectors such as shipbuilding, automotive and aviation can’t be imagined without laser processing technologies. Possibility of increase of welded joint properties, autogenous welding and high level of process automation makes the technology of laser welding perspective part of the industry. Physical...
-
Assessment of FSW Welds Made of Aluminum Alloy AW7075-T651.
PublicationThis paper summarizes the results of experimental studies in which the aluminum alloy AW7075-T651 was friction stir welded (FSW) using various combinations of process parameters (rotational - R and travel speed - T). Mechanical properties of the test welds were assessed by using static tensile test and Vickers hardness measurement. The temperature of the welded plates was monitored during welding by means of thermocouples placed...
-
FEM modelling of stress and strain distribution in weld joints of steel sandwich panels
PublicationThe development of laser welding technology has enabled the mass production of thin-walled structures, including steel sandwich panels. The technology of joining plating panels with stiffeners by welding allows us to create joints with a specific geometry and material properties. In comparison with other types of joints, laser welds are characterized by their specific behaviour under cyclic load and, as a consequence, a different...
-
Forming of explosively welded metal plates.
PublicationW pracy przedstawiono możliwości kształtowania plastycznego poprzez walcowanie, tłoczenie, gięcie, skręcanie blach wielowarstwowych zgrzewanych wybuchowo.
-
Underwater welded joint properties investigation
PublicationPrzeprowadzono badania mikro- i makroskopowe złączy spawanych typu implant wykonanych pod wodą metodą lokalnej komory suchej. Wyniki badań świadczą o tym, że w SWC badanych złączy tworzą się kruche struktury hartownicze, które są odpowiedzialne za zwiększoną skłonność stali o podwyższonej wytrzymałości do tworzenia pęknieć zimnych. Analiza rozkładów twardości złączy implant również potwierdza istnienie szkodliwego wpływu środowiska...
-
Technology of welding hard wearing plates
Publication -
Underwater Welding of Duplex Stainless Steel
PublicationThe present work was conducted to assess the weldability of duplex stainless steel at underwater conditions. Interest of underwater welding of this steel grade is connected with necessity of preparing welding repair technologies for subsea pipelines widely used in offshore oil and gas industry. The GMA local cavity welding method was used in the investigations. Welded beads were performed underwater at 0.5 m depth and in the air....
-
Review of titanium and steel welding methods
PublicationThe paper presents review of methods of titanium and steel welding. On basis of professional literature it was stated that titanium can be joined with steel by means of explosive welding or brazing.Joining titanium with steel by TIG welding and friction welding methods is possible with the use of copper and tantalum or vanadium interlayer.
-
Effects of preheating on laser beam–welded NSSC 2120 lean duplex steel
PublicationDuplex stainless steels show sustainable alternative for the conventional austenitic grades, with higher strength, higher resistance against stress corrosion cracking, and lower purchase cost. Thus, duplex stainless steel gains more attention in construction, oil and gas, and chemical industries. Among duplex stainless steels, low nickel and low molybdenum alloyed lean duplex stainless steel are a cost-efective substitution of...
-
Effect of Linear Energy and Microstructure on the Content of Residual Hydrogen in Welded Joints made of Superduplex Steels
PublicationThe article presents tests concerning the content of retained hydrogen present in FCAW and SAW welded joints made of superduplex steel. The use of various welding technologies resulted in the obtainment of welds having different microstructures and ferrite contents. Measurements of retained hydrogen present in joints (performed using the complete combustion method) revealed various contents of hydrogen in the base material and...
-
Corrigendum to “An investigation on residual stress and fatigue life assessment of T-shape welded joints” [Eng. Fail. Anal. 141 (2022) 106685]
PublicationThis paper aims to quantitatively evaluate the residual stress and fatigue life of T-type welded joints with a multi-pass weld in different direction. The main research objectives of the experimental test were to test the residual stress by changing direction along with multiple wielding passes and determine the fatigue life of the welded joints. The result shows that compressive residual stress increases in the sample gradually...
-
An investigation on residual stress and fatigue life assessment of T-shape welded joints
PublicationThis paper aims to quantitatively evaluate the residual stress and fatigue life of T-type welded joints with a multi-pass weld in different direction. The main research objectives of the experimental test were to test the residual stress by changing direction along with multiple wielding passes and determine the fatigue life of the welded joints. The result shows that compressive residual stress increases in the sample gradually...
-
Corrosion behavior of hydrogen charged super duplex stainless steel welded joints
PublicationThe electrochemical behavior of the weld metal, heat-affected zone (HAZ), and base material of super duplex stainless steel (SDSS) welded joints, made with the application of flux-cored arc welding (FCAW) and submerged arc welding (SAW), were investigated with the use of metallographic examinations (optical microscopy and scanning electron microscopy), potentiodynamic polarization measurements and total hydrogen content determination...
-
Underwater Local Cavity Welding of S460N Steel
PublicationIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Dissimilar underwater wet welding of HSLA steels
PublicationThe high-strength low-alloy S460ML and S460N steels were chosen for underwater wet welding of dissimilar T-joints using covered electrodes. For improving the quality of joints, the temper bead welding (TBW) method was used. The application of TBW in pad welding conditions has been investigated earlier but the possibility of usage of this technique in welded joints was not analyzed. The main aim of the study was to check the influence...
-
Numerical simulations of S700MC laser and hybrid welding
Publication -
Numerical Simulation of Duplex Steel Multipass Welding
Publication -
Fatigue life of steel, laser welded panels
PublicationW publikacji przedstawiono zagadnienia dotyczące możliwości analizy trwałości zmęczeniowej stalowyxh paneli spawanych laserowo typu sandwich. Przedstawiono wyniki badań laboratoryjnych w skali naturalnej a także krzywe projektowe uzyskane na podstawie systematycznych badań połączeń elementarnych spawanych laserowo. Na podstawie przedstawionych i uogólnionych wyników pokazano propozycję metodyki szacowania trwałości zmęczeniowej...
-
An experimental study of high-hydrogen welding processes
PublicationThis paper presents investigation results of determination of the diffusible hydrogen content in deposited metal obtained by means of two most often used methods-the glycerin method and the mercury method. Relation has been defined between results of those methods in the area characteristic of low-hydrogen as well as high-hydrogen welding processes. Relations available in the literature do not include the diffusible hydrogen content...
-
Application of Multivariate Analysis Methods in Welding Engineering
PublicationPhenomena and processes taking place during welding are usually very complex and, for this reason, should be described using multivariate methods. The article discusses the methodological basis and selected application areas as regards the solving of welding problems using statistical multivariate methods. In addition, the article presents exemplary applications of the design of experiment, multiple regression analysis, cluster...
-
Forecasting of fatigue life of laser welded joints
PublicationW pracy przedstawiono podstawowe dane na temat stalowych paneli typu sandwich. Zaprezentowano wyniki testów zmęczeniowych elementarnych połączeń teowych spawanych laserowo. Omówiono szczegółowo te cechy, które mają istotny wpływ na statyczne i zmęczeniowe własności złącza. Na podstawie przedstawionych wyników badań zmęczeniowych elementarnych połączeń spawanych laserowo uzyskano krzywą projektową S-N dla jednego z pokazanych modeli...
-
China Welding (English Edition)
Journals -
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING
Journals -
Influence of the notch rounding radius on estimating the elastic notch stress concentration factor in a laser welded tee joint
PublicationIn recent years an increased interest of industry in sandwich-type metal structures can be observed. These structures consist of thin plates of 2.5 mm in thickness separated by stiffeners of different shapes and forms. Welds joining the plates and stiffeners are made on the outer side of the plates using laser welding technique. A locally focused source of heat causes the plate to melt creating a very narrow and elongated joint....
-
Quality increase for single-welded joints of thin-walled structures by means of simulation modelling
PublicationThe Simulation calculation module and the SolidWorks software package have helped to define the optimal shape and dimensions of single-welded joints which may serve the basis for calculating the process parameters of welding. Having compared the models with different weld cross-sections the authors have defined that the weld height and width do not significantly affect the stress concentration, and the stress concentration and...
-
Fatigue properties of laser welded steel sandwich panel.
PublicationPrzedstawiono wyniki badań laboratoryjnych paneli SANDWICH, prowadzonych w Kat. TOiOO Wydz. OiO na konstrukcjach w skali rzeczywistej. Przedstawiono program badań, omówiono założenia procedur badawczych i konstrukcję stanowisk testowych. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze. Przedstawiono propozycję algorytmu szacowania trwałości zmęczeniowej konstrukcji spawanych laserowo.
-
APPLICATION POSSIBILITIES OF THE S960 STEEL IN UNDERWATER WELDED STRUCTURES
PublicationIn this paper, the application possibilities of the ultra-high strength (UHSS). Domex 960 steel in the underwater welded structures are analyzed. In the research, the investigated material has been tested in bead-on-plate wet welding conditions with the usage of different heat input values, namely 0.63 kJ/mm, 0.72 kJ/mm and 0.93 kJ/mm. Specimens were performed by the manual metal arc (MMA) welding method with the usage of rutile...
-
Possibilities for assesment of the angular distortion in Welded T-joint
PublicationSpawanie jest podstawową techniką łączenia elementów konstrukcji kadłuba statku. Procesowi temu towarzyszą odkształcenia spawalnicze, co przysparza dużo problemów wykonawczych. W pracy przedstawiono wpływ przewymiarowania spoiny pachwinowej na wielkość kątowych odkształceń złącza. Dokonano porównania wartości określonych na podstawie inżynierskich hipotez z wynikami otrzymanymi podczas prób laboratoryjnych.
-
Design of thermal cutting table - welding technology and construction
PublicationW referacie przedstawiono pionierską pracę dyplomową stopnia inżynierskiego, wykonaną przez dwoje studentów Wydziału Mechanicznego Politechniki Gdańskiej zgodnie z systemem CDIO (Conceive, Design, Implement, Operate). W ramach pracy studenci zaprojektowali stół do cięcia termicznego metali (rysunki i obliczenia wytrzymałościowe metodą elementów skończonych), opracowali technologię spawania stołu oraz samodzielnie go wykonali. Stół...
-
Bead-on-Plate Underwater Wet Welding on S700MC Steel
PublicationThe participation of high strength steels in marine and offshore structures is increasing, which makes it necessary to develop recommendations for underwater repair welding works. The article presents the results of bead-on-plate welded specimens made of S700MC high strength steel in underwater wet welding conditions by covered elec- trodes. Three specimens with heat input values in the range 0.91-1.05 kJ/mm were made. The specimens...