Publikacje
Filtry
wszystkich: 690
Katalog Publikacji
Rok 2020
-
Różne oblicza nanostruktur tlenku tytanu(IV)
PublikacjaW niniejszej pracy omówiono różnorodność nanostruktur tlenku tytanu(IV) w odniesieniu do ich zastosowania w fotokatalitycznej degradacji zanieczyszczeń organicznych, szczególnie niepodatnych na rozkład biologiczny.
-
Stability analysis of nanobeams in hygrothermal environment based on a nonlocal strain gradient Timoshenko beam model under nonlinear thermal field
PublikacjaThis article is dedicated to analyzing the buckling behavior of nanobeam subjected to hygrothermal environments based on the principle of the Timoshenko beam theory. The hygroscopic environment has been considered as a linear stress field model, while the thermal environment is assumed to be a nonlinear stress field based on the Murnaghan model. The size-dependent effect of the nanobeam is captured by the nonlocal strain gradient...
-
Stress-driven nonlocal elasticity for nonlinear vibration characteristics of carbon/boron-nitride hetero-nanotube subject to magneto-thermal environment
PublikacjaStress-driven nonlocal theory of elasticity, in its differential form, is applied to investigate the nonlinear vibrational characteristics of a hetero-nanotube in magneto-thermal environment with the help of finite element method. In order to more precisely deal with the dynamic behavior of size-dependent nanotubes, a two-node beam element with six degrees-of freedom including the nodal values of the deflection, slope and curvature...
-
Structural and catalytic properties of ceria layers doped with transition metals for SOFCs fueled by biogas
PublikacjaThe aim of this paper was to investigate an influence of the nanocrystalline Ce0.8A0.2O2-δ (A = Mn, Fe, Co, Ni, Cu) materials on the direct internal reforming of biogas in SOFC. Structural analysis of fabricated compounds has been done. An in-situ analysis of a composition of outlet gases from operating SOFC was performed using FTIR spectroscopy with simultaneous electrical tests. It was found out, that type of dopant strongly...
-
Submicron inorganic particles as an additional filler in hybrid epoxy matrix composites reinforced with glass fibres
PublikacjaIn this study, the effect of selected submicron metal oxide (zinc oxide, titanium oxide) or non-metal oxide (silicon dioxide) particles on mechanical and thermo-mechanical properties of epoxy/glass composites was investigated. The applied epoxy resin was a diglycidyl ether of bisphenol-A cured with triethylenetetramine. As a reinforcement twill weave E-glass fabric was used. Hybrid composites (contained particulate and fibrous...
-
Synthesis of CoFe2O4 Nanoparticles: The Effect of Ionic Strength, Concentration, and Precursor Type on Morphology and Magnetic Properties
PublikacjaThe present study highlights the effect of metal precursor types (SO4 2¯, Cl¯, and NO3¯), their concentration, and the influence of ionic strength of reaction environment on the morphology, surface, and magnetic properties of CoFe2O4 particles. The magnetic nanoparticles were obtained by chemical coprecipitation in alkaline medium at increasing metal concentration in the range of 0.0425 mol·dm-3 to 0.17 mol·dm-3 and calcination...
-
Teaching architectural history through virtual reality
PublikacjaThe impact of implementing 3D models and virtual reality in teaching the theory of architecture and architectural history is the theme of this article. Virtual reality and easy-to-use 3D tools allow a whole historic object to be visualised. As a result, there is social and economic pressure to modernise present educational methods using this technology. Therefore, the authors have focused their research on an issue of significance...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublikacjaThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
The experience of movement in orbital space architecture: A narrative of weightlessness
PublikacjaBased upon a combination of architectural theories, the knowledge of space environment, and psychology of isolated and confined environments, this qualitative research aims to study orbital space settlement in a way to get the built space congenial to the human experience of movement. In this sense, sensors, self-propulsion or mechanical actuators, the inhabitant’s mental and visual capacity for movement, as well as the represented...
-
THE IMPACT OF GROUND TIRE RUBBER TREATMENT ON THE THERMAL CONDUCTIVITY OF FLEXIBLE POLYURETHANE/GROUND TIRE RUBBER COMPOSITES
PublikacjaWaste car tires are burdensome waste, and their utilization is crucial for the natural environment. In many countries, the primary method of their recycling is energy recovery, performed by simple combustion. However, material recycling is much more effective and significantly more beneficial for the natural environment. It results in the generation of ground tire rubber, which can be used to produce polymerrubber composites. It...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
The Synergistic Microbiological Effects of Industrial Produced Packaging Polyethylene Films Incorporated with Zinc Nanoparticles
PublikacjaZinc compounds in polyolefin films regulate the transmission of UV-VIS radiation, affect mechanical properties and antimicrobial activity. According to hypothesis, the use of zinc- containing masterbatches in polyethylene films (PE) with different chemical nature—hydrophilic zinc oxide (ZO) and hydrophobic zinc stearate (ZS)—can cause a synergistic effect, especially due to their antimicrobial properties. PE films obtained on an...
-
Torsional stability capacity of a nano-composite shell based on a nonlocal strain gradient shell model under a three-dimensional magnetic field
PublikacjaThis paper considers a single-walled composite nano-shell (SWCNS) exposed in a torsional critical stability situation. As the magnetic field affects remarkably nanostructures in the small size, a three-dimensional magnetic field is assessed which contains magnetic effects along the circumferential, radial and axial coordinates system. Based on the results of the nonlocal model of strain gradient small-scale approach and the first-order...
-
Towards Changes of Macro-Economic Structures in Middle Eastern Countries. Empirical Evidence for 1970–2018
PublikacjaMiddle East countries share a wide bundle of specific structural economic features and one of the latest is a high dependency of these economies on fossil fuels, which is quantitatively demonstrated through the share of oil and gas revenues in total export, but also in gross domestic product composition. This high economic dependency on natural resources on one hand has recently generated a material wealth of Middle Eastern countries...
-
Ultrasound assisted synthesis of 3-alkynyl substituted 2-chloroquinoxaline derivatives: Their in silico assessment as potential ligands for N-protein of SARS-CoV-2
PublikacjaIn view of recent global pandemic the 3-alkynyl substituted 2-chloroquinoxaline framework has been explored as a potential template for the design of molecules targeting COVID-19. Initial in silico studies of representative compounds to assess their binding affinities via docking into the N-terminal RNA-binding domain (NTD) of N-protein of SARS-CoV-2 prompted further study of these molecules. Thus building of a small library of...
-
Vibration and buckling characteristics of nonlocal beam placed in a magnetic field embedded in Winkler–Pasternak elastic foundation using a new refined beam theory: an analytical approach
PublikacjaIn this article, a new refined beam theory, namely one variable first-order shear deformation theory, has been employed to study the vibration and buckling characteristics of nonlocal beam. The beam is exposed to an axial magnetic field and embedded in Winkler–Pasternak foundation. The von Kármán hypothesis along with Hamilton’s principle has been implemented to derive the governing equations for both the vibration and buckling...
-
VUV photofragmentation of the six-membered heterocyclic molecules containing oxygen
PublikacjaCancer is a significant public health concern worldwide, which results in millions of deaths each year. The standard cure routine for cancer is surgery, and nowadays, radiotherapy or a hadrontherapy. Depending on the type of cancer, patients may undergo additional treatment, including targeted therapy. A combination of radio- or hadron-therapy with proper drug treatment can inhibit the proliferation of cancer cells and thus can...
-
Wybrane zagadnienia projektowania, wykonawstwa oraz użytkowania betonowych posadzek przemysłowych w aspekcie ich ścieralności
Publikacjaw artykule przedstawiono najczęściej spotykane problemy związane z projektowaniem, realizacją oraz późniejszą eksploatacją posadzek w aspekcie ich ścieralności
Rok 2019
-
A comprehensive approach to double inverted pendulum modelling
PublikacjaThe problem of mathematical modelling and indication of properties of a DIP has been investigated in this paper. The aim of this work is to aggregate the knowledge on a DIP modelling using the Euler-Lagrange formalism in the presence of external forces and friction. To indicate the main properties important for simulation, model parameters identification and control system synthesis, analytical and numerical tools have been used....
-
Automated Parameter Determination for Horizontal Curves for the Purposes of Road Safety Models with the Use of the Global Positioning System
PublikacjaThis paper presents the results of research conducted to develop an automated system capable of determining parameters for horizontal curves. The system presented in this article could calculate the actual course of a road by means of a two-stage positioning of recorded points along the road. In the first stage, measurements were taken with a Real-Time Network (RTN) receiver installed in a research vehicle. In the second stage,...
-
Charakterystyka oporności Klebsiella pneumoniae New Delhi na karbapenemy
PublikacjaBakterie Klebsiella pneumoniae New Delhi, posiadające gen oporności na karbapenemy (blaNDM) zostały po raz pierwszy wyizolowane w 2008 roku w Szwecji od pacjenta wcześniej hospitalizowanego w Indiach. Bakterie te szybko rozprzestrzeniają się po całym świecie, a od 2011 roku występują również w Polsce. Stanowią one wysokie ryzyko epidemiologiczne, ponieważ gen oporności na karbapenemy przekazywany jest pomiędzy bakteriami poprzez...
-
Cross sections for electron collision with pyridine [C5H5N] molecule
PublikacjaThe absolute grand -total cross section (TCS) for electron scattering from pyridine, C5H5N, molecules has been measured at impact energies from 0.6 to 300 eV in the linear electron-transmission experiment. The obtained TCS energy dependence appears to be typical for targets of high electric-dipole moment; the cross section generally decreases with rising energy, except for the 3–20 eV range, where a broad enhancement peaked near...
-
Fabrication and Structural Properties of LaNb 1‐x As x O 4 Ceramics
PublikacjaLanthanum niobate substituted with arsenic was synthesized by three methods: solid state reaction from binary oxides and two different methods combining co-precipitation and solidstate reaction. In the first of the combined methods LaNb1- xAsxO4 was synthesized from LaAsO4, obtained from coprecipitation method, and lanthanum and niobium oxides. In the second LaNbO4 was first synthesized from binary oxides and then mixed with LaAsO4...
-
Fast Basis Function Estimators for Identification of Nonstationary Stochastic Processes
PublikacjaThe problem of identification of a linear nonsta-tionary stochastic process is considered and solved using theapproach based on functional series approximation of time-varying parameter trajectories. The proposed fast basis func-tion estimators are computationally attractive and yield resultsthat are better than those provided by the local least squaresalgorithms. It is shown that two...
-
In situ study of a composition of outlet gases from biogas fuelled Solid Oxide Fuel Cell performed by the Fourier Transform Infrared Spectroscopy
PublikacjaThe purpose of this study was to develop a method and software based on the Fourier Transform Infrared Spectroscopy for the in-situ, quantitative analysis of the composition of outlet gases from Solid Oxide Fuel Cell (SOFC). The calibration procedure performed at the beginning of the experiment indicated a polynomial dependence between the concentration of a calibrating gas (CO, CO2, CH4) and the corresponding integrated absorbance in...
-
Local basis function estimators for identification of nonstationary systems
PublikacjaThe problem of identification of a nonstationary stochastic system is considered and solved using local basis function approximation of system parameter trajectories. Unlike the classical basis function approach, which yields parameter estimates in the entire analysis interval, the proposed new identification procedure is operated in a sliding window mode and provides a sequence of point (rather than interval) estimates. It is...
-
Metody strojenia regulatorów typu PID z wykorzystaniem technologii syntezy regulatorów od stanu
PublikacjaUkłady sterujące typu PID są jednymi z najbardziej popularnych regulatorów wykorzystywanych w układach regulacji. W związku z tym znanych jest szereg metod doboru wartości ich parametrów (nastaw). Obok różnych metod inżynierskich czy analitycznych strojenia tego typu regulatorów, dostępne są również podejścia bazujące na optymalizacji. Wskaźnikiem jakości znajdującym w nich zastosowanie jest np. całka z kwadratu uchybu. W artykule...
-
MicroGal Gravity Measurements with MGS-6 Micro-g LaCoste Gravimeter
PublikacjaKnowing the exact number of fruit and trees helps growers to make better decisions about how to manage their production in the orchard and prevent plant diseases. The current practice of yield estimation is to manually count fruit or flowers (before harvesting), which is a very time-consuming and costly process. Moreover it’s not practical for large orchards. It also doesn’t allow to make predictions of plant development in a more...
-
Optical Magnetometry Based on Nanodiamonds with Nitrogen-Vacancy Color Centers
PublikacjaNitrogen-vacancy color centers in diamond are a very promising medium for many sensing applications such as magnetometry and thermometry. In this work, we study nanodiamonds deposited from a suspension onto glass substrates. Fluorescence and optically detected magnetic resonance spectra recorded with the dried-out nanodiamond ensembles are presented and a suitable scheme for tracking the magnetic-field value using a continuous...
-
Prądy łożyskowe w układach napędowych z silnikami indukcyjnymi
PublikacjaW pracy przedstawiono problemy występujące w układach napędowych z silnikami indukcyjnymi zasilanymi z falownika napięcia. Zwrócono uwagę na rosnącą liczbę uszkodzeń silników w napędach przekształtnikowych. Wskazano przyczyny wynikające z charakteru zasilania przekształtnikowego silnika. Główną uwagę poświęcono prądowi łożyskowemu, który odpowiada za większość awarii maszyn. Przedstawiono rodzaje prądów łożyskowych, wyjaśniając...
-
Projekt systemu sterowania dwukołowym robotem balansującym
PublikacjaW niniejszym artykule rozważony został problem sterowania dwukołowym robotem balansującym. Celem zaprezentowanych prac było zaprojektowanie systemu sterowania tego typu obiektem z wykorzystaniem metod nowoczesnej teorii sterowania. W ramach syntezy, bazując na wyprowadzonym w oparciu o zasady dynamiki Newtona modelu, dobrana została struktura systemu sterowania w postaci regulatora wykorzystującego sprzężenie zwrotne od stanu oraz...
-
Road Restraint Systems as a Basis for Roadside Safety Improvement
PublikacjaRoadside-related crashes occur when vehicles run off the road. The majority of the crashes have severe outcomes, especially when an object is hit (tree, pole, supports, front wall of a culvert, barrier). These accidents represent app. 19% of all of Poland's road deaths. Roadside crashes involve: hitting a tree, hitting a barrier, hitting a sign or utility pole, vehicle roll-over on the roadside, vehicle roll-over on a slope and...
-
Seismic pounding between adjacent buildings: Identification of parameters, soil interaction issues and mitigation measures
PublikacjaStructural pounding has been observed in many previous earthquakes due to insufficient gap commonly provided between adjacent structures. The collisions usually generate large impact forces and short duration acceleration pulses which may result in significant damage to the colliding buildings. Because of that, earthquake induced structural pounding has been intensively studied and investigated for the last three decades. Results...
-
Sources of inspiration in designing ecological buildings. If not Pinterest than what?
PublikacjaEfficiency of ecological measures for sustainable architecture depends greatly upon the moment in which it is defined as essential, and how early it can be applied during the design concept stage. The following article refers to inspiration, the initial stage of the design and means to combine it with substantial knowledge regarding ecological architecture. Means, such as computer programs...
-
The Effects of Roadside Hazards on Road Accident Severity
PublikacjaThe risk of becoming involved in an accident emerges when elements of the transport system do not operate properly (man – vehicle – road – roadside). The road, its traffic layout andsafety equipment have a critical impact on road user safety. This gives infrastructural work a priority in road safety strategies and programmes. Run-off-road accidents continue to be one of the biggest problems of road safety with consequences including...
-
The effects of selected factors on regional road fatalities – analysis of the Łódź region
PublikacjaAnalysis of regional accident records shows that a country’s national road safety programme does not have the same effect in each of its regions. What may be a serious problem in one region may be of marginal significance in another. Polish and international experience shows that main risk groups and types of accidents related to the level of development and quality of the road network differ from region to region. The conclusion...
-
The experience of movement in the built form and space: A framework for movement evaluation in architecture
Publikacja“Movement in architecture” is an organized system of various types of movements stimulated by specific architectural elements. This research was conducted through a qualitative-analytical method and empirical and bibliographical research methods with the aim to categorize different types of movements based on the explorer and observer relationships with the built space and form. So far, most of the related studies have focused...
-
Tynki w budownictwie ogólnym. wybrane badania oraz problemy eksploatacyjne
PublikacjaMonografia stanowi studium przypadku problemów związanych z realizacją oraz eksploatacją tynków stosowanych w obiektach budownictwa ogólnego
-
Wytwarzanie i wybrane właściwości kompozycji kauczukowych z regenerowaną celulozą.
PublikacjaCelem niniejszej pracy było zbadanie wpływu regenerowanych włókien wiskozowych (dodanych w ilości 10, 20, 30 phr) jako proekologicznego napełniacza na wybrane właściwości kompozycji na osnowie kauczuku na-turalnego. Dla każdej z wyżej wymienionych proporcji otrzymano materiały wulkanizowane przez 5, 10, 15, 20 minut. Uzyskane materiały poddano statycznej próbie rozciągania, badaniu elastyczności przy odbiciu metodą...
-
Zastosowanie metody szacowania kosztów cyklu życia w zarządzaniu infrastrukturą transportową
PublikacjaZarządzanie infrastrukturą transportową powinno przebiegać w myśl zrównoważonego rozwoju. Należy podejmować działania i czynności, które łączą w sposób optymalny aspekty środowiskowe, społeczne oraz wydatki ponoszone na rzecz infrastruktury. W artykule przedstawiono koncepcję myślenia w cyklu życia uwzględniające powyższe problemy. Praktycznym narzędziem służącym do zarządzania infrastrukturą transportową jest metoda szacowania...